RESUMEN

In this study, we propose a non - toxic and low-cost fabrication of cellulose-based eutectogel through the ZnCl2/H2O/H3PO4 deep eutectic solvent (DES) to dissolve cellulose followed by free-radical polymerization of acrylamide. Particularly, the introduction of cellulose enhances the mechanical properties of eutectogels while eliminating the environmental concerns of the traditional nanocellulose fabrication process. Owing to the dynamic transfer of ions in the eutectogel network, the prepared eutectogels exhibit adjustable conductivity (0.9- 1.37 Sm-1, 15 °C) and stretching sensitivity (Gauge factor = 5.4). The resulting DES - cellulose-based eutectogels (DCEs) exhibited ultra stretchability (4086 %), high toughness (261.3 MJ/m3), excellent ionic conductivity (1.64 Sm-1, 20 °C), high transparency (>85 %), outstanding antifreezing performance (<-80 °C), and other comprehensive characteristics. The DCEs had been proven to have multiple sensitivities to external stimuli, like temperature, strain, and pressure. As a result, the DCEs can be assembled into multifunctional sensors. Moreover, this work also demonstrated the satisfactory performance of DCEs in flexible electroluminescent devices. The low cost and high efficiency made the preparation method of this experiment an efficient strategy for developing high-performance cellulose-based eutectogels, which would greatly promote the application of such materials in areas such as artificial skin for soft robots and other wearable devices.

Asunto(s)

RESUMEN

Integrated safety sensors for personal protection equipment increasingly attract research activities as there is a high need for workers in delicate situations to be physically monitored in order to avoid accidents. In this work, we present a simple approach to generate thin, homogeneous polypyrrole (PPy) layers on flexible textile polyamide fabrics. PPy layers of 0.5-1 µm were deposited on the fabric, which thus kept its flexibility. The conductive layers are multifunctional and can act as temperature and gas sensors for the detection of corrosive gases such as HCl and NH3. Using three examples of life-threatening environments, we were able to monitor temperature, atmospheric NH3 and HCl within critical ranges, i.e., 100 to 400 ppm for ammonia and 20 to 100 ppm for HCl. In the presence of HCl, a decrease in resistance was observed, while gaseous NH3 led to an increase in resistance. The sensor signal thus allows for distinguishing between these two gases and indicating critical concentrations. The simple and cheap manufacturing of such PPy sensors is of substantial interest for the future design of multifunction functional sensors in protective clothing.

RESUMEN

Accurate acquisition of physiological and physical information from human tissue is essential for health monitoring, disease prevention and treatment. The existing antennas with traditional rigid or flexible substrates are susceptible to motion artifacts in wearable applications due to the miniaturization limitation and lack of proper adhesion and conformal interfaces with the skin. Recent advances in wearable radio frequency (RF) bioelectronics directly drawn on the skin are a promising solution for future skin-interfaced devices. Herein, we present a first-of-its kind epidermal antenna architecture with skin as the antenna substrate, which is ultra-low profile, ultra-conformal, ultra-compact, and simple fabrication without specialized equipment. The radiation unit and ground of antenna are drawn directly on the skin with the strong adhesion and ultra conformality. Therefore, this RF device is highly adaptable to motion. As a proof-of- feasibility, epidermal antenna can be freely drawn on demand at different locations on the skin for the development of temperature sensor, skin hydration sensor, strain sensor, glucose sensor and other devices. An epidermal antenna-based temperature sensor can offer accurate and real-time monitoring of human body temperature changes in the ultra-wideband (UWB) range. The results during the monitoring of hydration level with and without stretching show that the epidermal antenna drawn on the skin is motion artifact-free. We also designed an epidermal antenna array employing a horseshoe-shaped configuration for the precise identification of various gestures. In addition, the non-invasive blood glucose level (BGL) monitoring results during the in-vivo experiments report high correlation between the epidermal antenna responses and BGLs, without any time hysteresis. After the prediction of BGL by BP network, all the predicted BGL values are fallen 100% into the clinically acceptable zones. Together, these results show that epidermal antenna offers a promising new approach for biosensing platform.

Asunto(s)

RESUMEN

Food packaging detection devices have attracted attention to optimize storage situations and reduce food spoilage. However, low-cost and highly sensitive multifunctional sensors for detecting both food freshness and packaging pressure are still lacking. In this study, a multifunctional sensor was developed consisting of a MXene coated alcohol-soluble polyurethane fiber network (MXene/APU) and composite biohydrogel films made of konjac glucomannan, chitosan, and blueberry anthocyanin (KCB). Based on the pressure sensitivity of MXene/APU and the color changes of KCB in response to pH values, the sensor can detect internal package bulging, external squeezing, and food deterioration. The pressure sensor shows a sensitivity of 1.16 kPa-1, a response time of 200 ms, a wide strain range of 1092%, and stability over multiple loops. The pressure sensor could detect human motion and identify surface morphologies. The excellent sensor performance was attributed to the porous structure and large specific surface area of microfiber networks, conductivity of MXene nanosheets, and protective effect of KCB films coated on the conductive membrane. Besides, the microfluidic blow-spinning method used to prepare microfiber networks showed the advantages of low energy consumption and high production efficiency. Based on the color changes of blueberry anthocyanin loaded in KCB films in response to pH, the sensor realized sensitive spoilage detection of food containing protein. This study provides a new multifunctional food packaging sensing device and a greater understanding of the optimization and application of related devices.

Asunto(s)

RESUMEN

This paper presents the Tactile Blep (T-Blep), an optical soft sensor that can measure the stiffness and force of different materials. The sensor consists of an inflatable membrane with an optical elements inside. The T-Blep can switch between stiffness detection and force detection modes, by changing the pattern followed by internal pressure of the membrane. Simulations reveal that a 1 mm-thick membrane enables differentiation of extra-soft, soft, and rigid targets. Furthermore, the sensitivity and FSO of the force estimation can be adjusted by varying the internal pressure. Force detection experiments exhibit a sixfold increase in detectable force range as internal pressure varies from 10 kPa to 40 kPa, with a force peak of 5.43 N and sensitivity up to 331 mV/N. A piecewise force reconstruction method provides accurate results even in challenging conditions (R2>0.994). Stiffness detection experiments reveal distinguishable patterns of pressure and voltage during indentation, resulting in a classification accuracy of 97%.

RESUMEN

Online monitoring of prognostic biomarkers is critically important when diagnosing disorders and assessing individuals' health, especially for chronic and infectious diseases. Despite this, current diagnosis techniques are time-consuming, labor-intensive, and performed offline. In this context, developing wearable devices for continuous measurements of multiple biomarkers from body fluids has considerable advantages including availability, rapidity, convenience, and minimal invasiveness over the conventional painful and time-consuming tools. However, there is still a significant challenge in powering these devices over an extended period, especially for applications that require continuous and long-term health monitoring. Herein, a new freestanding, wearable, multifunctional microneedle-based extended gate field effect transistor biosensor is fabricated for online detection of multiple biomarkers from the interstitial fluid including sodium, calcium, potassium, and pH along with excellent electrical response, reversibility, and precision. In addition, a hybrid powering system of triboelectric nanogenerator and solar cell was developed for creating a freestanding, closed-loop platform for continuous charging of the device's battery and integrated with an Internet of Things technology to broadcast the measurements online, suggesting a stand-alone, stable multifunctional tool which paves the way for advanced practical personalized health monitoring and diagnosis.

RESUMEN

With the commercialization of first-generation flexible mobiles and displays in the late 2010s, humanity has stepped into the age of flexible electronics. Inevitably, soft multifunctional sensors, as essential components of next-generation flexible electronics, have attracted tremendous research interest like never before. This review is dedicated to offering an overview of the latest emerging trends in soft multifunctional sensors and their accordant future research and development (R&D) directions for the coming decade. First, key characteristics and the predominant target stimuli for soft multifunctional sensors are highlighted. Second, important selection criteria for soft multifunctional sensors are introduced. Next, emerging materials/structures and trends for soft multifunctional sensors are identified. Specifically, the future R&D directions of these sensors are envisaged based on their emerging trends, namely i) decoupling of multiple stimuli, ii) data processing, iii) skin conformability, and iv) energy sources. Finally, the challenges and potential opportunities for these sensors in future are discussed, offering new insights into prospects in the fast-emerging technology.

RESUMEN

Wearable electronics have received extensive attention in human-machine interactions, robotics, and health monitoring. The use of multifunctional sensors that are capable of measuring a variety of mechanical or environmental stimuli can provide new functionalities for wearable electronics. Advancements in material science and system integration technologies have contributed to the development of high-performance flexible multifunctional sensors. This review presents the main approaches, based on functional materials and device structures, to improve sensing parameters, including linearity, detection range, and sensitivity to various stimuli. The details of electrical, biocompatible, and mechanical properties of self-powered sensors and wearable wireless systems are systematically elaborated. Finally, the current challenges and future developmental directions are discussed to offer a guide to fabricate advanced multifunctional sensors.

RESUMEN

Humans can perceive our complex world through multi-sensory fusion. Under limited visual conditions, people can sense a variety of tactile signals to identify objects accurately and rapidly. However, replicating this unique capability in robots remains a significant challenge. Here, we present a new form of ultralight multifunctional tactile nano-layered carbon aerogel sensor that provides pressure, temperature, material recognition and 3D location capabilities, which is combined with multimodal supervised learning algorithms for object recognition. The sensor exhibits human-like pressure (0.04-100 kPa) and temperature (21.5-66.2 °C) detection, millisecond response times (11 ms), a pressure sensitivity of 92.22 kPa-1 and triboelectric durability of over 6000 cycles. The devised algorithm has universality and can accommodate a range of application scenarios. The tactile system can identify common foods in a kitchen scene with 94.63% accuracy and explore the topographic and geomorphic features of a Mars scene with 100% accuracy. This sensing approach empowers robots with versatile tactile perception to advance future society toward heightened sensing, recognition and intelligence.

RESUMEN

Flexible mechanical sensors based on nanomaterials operate on a deformation-response mechanism, making it challenging to discern different types of mechanical stimuli such as pressure and strain. Therefore, these sensors are susceptible to significant mechanical interference. Here, we introduce a multifunctional flexible sensor capable of discriminating coupled pressure and strain without cross-interference. Our design involves an elastic cantilever fixed on the pillar of the flexible main substrate, creating a three-dimensional (3D) substrate, and two percolative nanoparticle (NP) arrays are deposited on the cantilever and main substrate, respectively, as the sensing materials. The 3D flexible substrate could confine pressure/strain loading exclusively on the cantilever or main substrate, resulting in independent responses of the two nanoparticle arrays with no cross-interference. Benefitting from the quantum transport in nanoparticle arrays, our sensors demonstrate an exceptional sensitivity, enabling discrimination of subtle strains down to 1.34 × 10-4. Furthermore, the suspended cantilever with one movable end can enhance the pressure perception of the NP array, exhibiting a high sensitivity of -0.223 kPa-1 and an ultrahigh resolution of 4.24 Pa. This flexible sensor with multifunctional design will provide inspiration for the development of flexible mechanical sensors and the advancement of decoupling strategies.

Asunto(s)

RESUMEN

A traditional injectable photocrosslinked hydrogel had disadvantages of the residual photoinitiator and toxic crosslinker, slow in situ curing, and a complex preparation process. At the same time, hydrogels cannot act as artificial skin to restore skin sensory function during the wound healing cycle. In this work, an injectable photocrosslinked hydrogel was prepared which can be quickly in situ cured without photoinitiator. Oxidized sodium alginate was used as a natural macromolecular crosslinking agent to form an injectable hydrogel framework with the photosensitive polymer polyvinyl alcohol bearing styrylpyridinium group (PVA-SBQ). In addition, the hydrogel was endowed with photothermal therapy property after the introduction of biomass-like polydopamine particles. When used as a wound dressing, the hydrogel exhibited an excellent antibacterial property, with an antibacterial rate of 99.56% Escherichia coli and 97.96% Staphylococcus aureus. As a result, the hydrogel could significantly accelerate the repair of infected wounds, with a wound healing rate of 96.45% after 14 days. Moreover, the hydrogel exhibited a sensitive and stable sensing property, making it promising to reconstitute the sensory function of damaged skin during treatment. This work provides an idea for the development of injectable photocrosslinked hydrogel dressing.

Asunto(s)

RESUMEN

A multi-functional sensing system based on surface plasmon resonance (SPR) phenomenon using a square glass rod with two gold-deposited adjacent faces was developed in this work. This sensor system consists of a unpolarized light-emitting diode, a gold-deposited square glass rod, a polarizing beam splitter, and two photodiodes. The SPR responses of two adjacent faces are independently and simultaneously measured with a polarizing beam splitter and two PDs. The response property of the gold-deposited face was confirmed using methanol solutions of ethylene glycol. The response curve of the sensor of the 45 nm gold-deposited face was compared with the theoretical curve calculated using multi-layer Fresnel equations. It was confirmed that the experimental curve is similar to the theoretical one. An evaluation was carried out on the square glass rod, which has an unmodified face and Teflon AF2400 coated gold-deposited face as multi-functional sensor. It was confirmed that this sensor can simultaneously measure the ethanol concentration in the glucose mix solution and refractive index of the sample from the calibration curve. Since this sensor can measure multiple components simultaneously, expected applications to various fields include medical diagnosis, food analysis, and environmental monitoring.

RESUMEN

Developing sensors for monitoring physiological parameters such as temperature and strain for point of care (POC) diagnostics is critical for better care of the patients. Various commercial sensors are available to get the job done; however, challenges like the structural rigidity of such sensors confine their usage. As an alternative, flexible sensors have been looked upon recently. In most cases, flexible sensors cannot discriminate the signals from different stimuli. While there have been reports on the printable sensors providing cross-talk-free solutions, research related to developing sensors from a sustainable source providing discriminability between signals is not well-explored. Herein, we report the development of a stencil printable composition made of graphene and epoxidized natural rubber. The stencil printability index was vetted using rheological studies. Post usage, the developed sensor was dissolved in an organic solvent at room temperature. This, along with the choice of a sustainable elastomer, warrants the minimization of electronic waste and carbon footprint. The developed material demonstrated good conformability with the skin and could perceive and decouple the signals from temperature and strain without inducing any crosstalks. Using a representative volume element model, a comparison between experimental findings and computation studies was made. The developed sensors demonstrated gauge factors of -506 and 407 in the bending strain regimes of 0-0.04% and 0.04%-0.09%, respectively, while the temperature sensitivity was noted to be -0.96%/°C. The printed sensors demonstrated a multifunctional sensing behavior for monitoring various active physiological parameters ranging from temperature, strain, pulse, and breathing to auditory responses. Using a Bluetooth module, various parameters like temperature and strain could be monitored seamlessly in a smart-phone. The current development would be crucial to open new avenues to fabricate crosstalk-free sensors from sustainable sources for POC diagnostics.

Asunto(s)

RESUMEN

Motion sensors are an essential component of many electronic systems. However, the development of inertial motion sensors based on fatigue-free soft proof mass has not been explored extensively in the field of soft electronics. Nontoxic gallium-based liquid metals are an emerging class of material that exhibit attractive electromechanical properties, making them excellent proof mass materials for inertial sensors. Here, we propose and demonstrate a fully soft laser-induced graphene (LIG) and liquid metal-based inertial sensor integrated with temperature, humidity, and breathing sensors. The inertial sensor design confines a graphene-coated liquid metal droplet inside a fluidic channel, rolling over LIG resistive electrode. The proposed sensor architecture and material realize a highly mobile proof mass and a vibrational space for its oscillation. The inertial sensor exhibits a high sensitivity of 6.52% m-1 s2 and excellent repeatability (over 12 500 cycles). The platform is fabricated using a scalable, rapid laser writing technique and integrated with a programmable system on a chip (PSoC) to function as a stand-alone system for real-time wireless monitoring of movement patterns and the control of a robotic arm. The developed printed inertial platform is an excellent candidate for the next-generation of wearables motion tracking platforms and soft human-machine interfaces.

Asunto(s)

RESUMEN

Developing a printed elastomeric wearable sensor with good conformity and proper adhesion to skin, coupled with the capability of monitoring various physiological parameters, is very crucial for the development of point-of-care sensing devices with high precision and sensitivity. While there have been previous reports on the fabrication of elastomeric multifunctional sensors, research on the printable elastomeric multifunctional adhesive sensor is not very well explored. Herein, we report the development of a stencil printable multifunctional adhesive sensor fabricated in a solvent-free condition, which demonstrated the capability of having good contact with skin and its ability to function as a temperature and strain sensor. Functionalized liquid isoprene rubber was selected as the matrix while carboxylated multiwalled carbon nanotubes (c-CNTs) were used as the nanofiller. The selection of the above model compounds facilitated the printability and also helped the same composition to demonstrate stretchability and adhesiveness. A realistic three-dimensional microstructure (representative volume element model) was generated through a computational framework for the current c-CNT-liquid elastomer. Further computational simulations were performed to test and validate the correlation between electrical responses to that of experimental studies. Various physiological parameters like motion sensing, pulse, respiratory rate, and phonetics detection were detected by leveraging the electrically resistive nature of the sensor. This development route can be extended toward developing different innovative adhesives for point-of-care sensing applications.

Asunto(s)

RESUMEN

Multifunctional environmental sensing is crucial for various applications in agriculture, pollution monitoring, and disease diagnosis. However, most of these sensing systems consist of multiple sensors, leading to significantly increased dimensions, energy consumption, and structural complexity. They also often suffer from signal interferences among multiple sensing elements. Herein, we report a multifunctional environmental sensor based on one single sensing element. A MoS2 film was deposited on the surface of a piezoelectric microcantilever (300 × 1000 µm2) and used as both a sensing layer and top electrode to make full use of the changes in multiple properties of MoS2 after its exposure to various environments. The proposed sensor has been demonstrated for humidity detection and achieved high resolution (0.3% RH), low hysteresis (5.6%), and fast response (1 s) and recovery (2.8 s). Based on the analysis of the magnitude spectra for transmission using machine learning algorithms, the sensor accurately quantifies temperatures and CO2 concentrations in the interference of humidity with accuracies of 91.9 and 92.1%, respectively. Furthermore, the sensor has been successfully demonstrated for real-time detection of humidity and temperature or CO2 concentrations for various applications, revealing its great potential in human-machine interactions and health monitoring of plants and human beings.

Asunto(s)

RESUMEN

Monitoring biosignals at the skin interface is necessary to suppress the potential for decubitus ulcers in immobile patients confined to bed. We develop conformally contacted, disposable, and breathable fabric-based electronic devices to detect skin impedance, applied pressure, and temperature, simultaneously. Based on the experimental evaluation of the multifunctional sensors, a combination of robust AgNW electrodes, soft ionogel capacitive pressure sensor, and resistive temperature sensor on fabric provides alarmed the initiation of early-stage decubitus ulcers without signal distortion under the external stimulus. For clinical verification, an animal model is established with a pair of magnets to mimic a human decubitus ulcers model in murine in vivo. The evidence of pressure-induced ischemic injury is confirmed with the naked eye and histological and molecular biomarker analyses. Our multifunctional integrated sensor detects the critical time for early-stage decubitus ulcer, establishing a robust correlation with the biophysical parameters of skin ischemia and integrity, including temperature and impedance.

Asunto(s)

RESUMEN

Multifunctional electronic skins have attracted considerable attention for soft electronics including humanoid robots, wearable devices, and health monitoring systems. Simultaneous detection of multiple stimuli in a single self-powered device is desired to simplify artificial somatosensory systems. Here, inspired by the structure and function of human skin, an ultrasensitive self-powered multimodal sensor is demonstrated based on an interlocked ferroelectric copolymer microstructure. The triboelectric and pyroelectric effects of ferroelectric microstructures enable the simultaneous detection of mechanical and thermal stimuli in a spacer-free single device, overcoming the drawbacks of conventional devices, including complex fabrication, structural complexity, and high-power consumption. Furthermore, the interlocked microstructure induces electric field localization during ferroelectric polarization, leading to enhanced output performance. The multimodal tactile sensor provides ultrasensitive pressure and temperature detection capability (2.2 V kPa-1 , 0.27 nA °C-1 ) over a broad range (0.1-98 kPa, -20 °C < ΔT < 30 °C). Furthermore, multiple simultaneous stimuli can be distinguished based on different response times of triboelectric and pyroelectric effects. The remarkable performance of this sensor enables real-time monitoring of pulse pressure, acoustic wave detection, surface texture analysis, and profiling of multiple stimuli.

Asunto(s)

RESUMEN

Recent advances in wearable patches have included various sensors to monitor either physiological signs, such as the heart rate and respiration rate, or metabolites. Nevertheless, most of these have focused only on a single physiological measurement at a time, which significantly inhibits the calibration of various biological signals and diagnostic facilities. In this study, a novel multifunctional hybrid skin patch was developed for the electrochemical analysis of sweat glucose levels and simultaneous monitoring of electrocardiograms (ECGs). Furthermore, pH and temperature sensors were co-integrated onto the same patch for the calibration of the glucose biosensor to prevent inevitable inhibition and weakening of enzyme activity due to changes in the sweat pH and temperature levels. The fabricated electrochemical glucose biosensor exhibited excellent linearity (R2 = 0.9986) and sensitivity (29.10 µA mM-1 cm-2), covering the normal range of human sweat. The potentiometric pH sensor displayed a good response with an excellent sensitivity of -77.81 mV/pH and high linearity (R2 = 0.991), indicating that it can distinguish variations in the typical pH range for human sweat. Furthermore, the P, QRS complex, and T peaks in the measured ECG waveforms could be clearly distinguished, indicating the reliability of the fabricated flexible dry electrodes for continuous monitoring. The fabricated skin patch overcomes the inconvenience of the mandatory attachment of multiple patches on the human body by fully integrating all the electrochemical and electrophysiological sensors on a single patch, thus facilitating advanced glycemic control and continuous ECG monitoring for smart management of chronic diseases and healthcare applications.

Asunto(s)

RESUMEN

With the demand for accurately recognizing human actions and environmental situations, multifunctional sensors are essential elements for smart applications in various emerging technologies, such as smart robots, human-machine interface, and wearable electronics. Low-dimensional materials provide fertile soil for multifunction-integrated devices. This review focuses on the multifunctional sensors for mechanical stimulus and environmental information, such as strain, pressure, light, temperature, and gas, which are fabricated from low-dimensional materials. The material characteristics, device architecture, transmission mechanisms, and sensing functions are comprehensively and systematically introduced. Besides multiple sensing functions, the integrated potential ability of supplying energy and expressing and storing information are also demonstrated. Some new process technologies and emerging research areas are highlighted. It is presented that optimization of device structures, appropriate material selection for synergy effect, and application of piezotronics and piezo-phototronics are effective approaches for constructing and improving the performance of multifunctional sensors. Finally, the current challenges and direction of future development are proposed.

Asunto(s)