RESUMO

Legumes are abundant sources of proteins, and white common bean proteins play an important role in air-water interface properties. This study aims to investigate the technical-functional properties of white common bean protein isolate (BPI) as a function of pH, protein concentration, and guar gum (GG) presence. BPI physicochemical properties were analyzed in terms of solubility, zeta potential, and mean particle diameter at pH ranging from 2 to 9, in addition to water-holding capacity (WHC), oil-holding capacity (OHC), and thermogravimetric analysis. Protein dispersions were evaluated in terms of dynamic, interfacial, and foam-forming properties. BPI showed higher solubility (>80 %) at pH 2 and above 7. Zeta potential and mean diameter ranged from 15.43 to -34.08 mV and from 129.55 to 139.90 nm, respectively. BPI exhibited WHC and OHC of 1.37 and 4.97 g/g, respectively. Thermograms indicated decomposition temperature (295.81 °C) and mass loss (64.73 %). Flow curves indicated pseudoplastic behavior, with higher η100 values observed in treatments containing guar gum. The behavior was predominantly viscous (tg δ > 1) at lower frequencies, at all pH levels, shifting to predominantly elastic at higher frequencies. Equilibrium surface tension (γeq) ranged from 43.87 to 41.95 mN.m-1 and did not decrease with increasing protein concentration under all pH conditions. All treatments exhibited ϕ < 15°, indicating predominantly elastic surface films. Foaming properties were influenced by higher protein concentration and guar gum addition, and the potential formation of protein-polysaccharide complexes favored the kinetic stability of the system.

Assuntos

RESUMO

In this work, a numerical method is proposed to predict the electrokinetic phenomena and combined with an experimental study of the surface charge density (ρs) and zeta potential (ζ) behavior is investigated for borosilicate immersed in KCl and NaCl electrolytes, and for imogolite immersed in KCl, CaCl2, and MgCl2 electrolytes. Simulations and experiments of the electrokinetic flows with electrolyte solutions were performed to accurately determine the electric double layer (EDL), ζ, and ρs at various electrolyte concentrations and pH. The zeta potential was experimentally determined and numerically predicted by solving the coupled governing equations of mass, species, momentum, and electrical field iteratively. Our numerical prediction shows that ζ for borosilicate develops strong nonlinear behavior with the ion concentration following a power-law. Likewise, the ρs obeys a nonlinear behavior, decreasing as the concentration increases. Moreover, for imogolite, both ζ and the ρs behave nonlinearly with the pH. The EDL for borosilicate and imogolite becomes thinner as the electrolyte concentration and pH increase; this behavior is caused by increased ρs, resulting in the higher attraction of the free charges. The reported nonlinear behavior describes more accurately the interaction of the nanoparticle surface charge with the electrolytes and its effect on the electrolyte transport properties.

RESUMO

The oil extracted from baru (Dipteryx alata Vog.) seeds is in bioactive compounds and it presents potential to be used in food and cosmetic industries. Therefore, this study aims to provide insights into the stability of baru oil-in-water (O/W) nanoemulsions. For this purpose, the effects of the ionic strength (0, 100 and 200 mM), pH (6, 7 and 8), and storage time (28 days) on the kinetic stability of these colloidal dispersions were evaluated. The nanoemulsions were characterized in terms of interfacial properties, rheology, zeta potential (ζ), average droplet diameter, polydispersity index (PDI), microstructure, and creaming index. In general, for samples, the equilibrium interfacial tension ranged from 1.21 to 3.4 mN.m-1, and the interfacial layer presented an elastic behavior with low dilatational viscoelasticity. Results show that the nanoemulsions present a Newtonian flow behavior, with a viscosity ranging from 1.99 to 2.39 mPa.s. The nanoemulsions presented an average diameter of 237-315 nm with a low polydispersity index (<0.39), and a ζ-potential ranging from 39.4 to 50.3 mV after 28 days of storage at 25 °C. The results obtained for the ζ-potential suggest strong electrostatic repulsions between the droplets, which is an indicative of relative kinetic stability. In fact, macroscopically, all the nanoemulsions were relatively stable after 28 days of storage, except the nanoemulsions added with NaCl. Nanoemulsions produced with baru oil present a great potential to be used in the food, cosmetic, and pharmaceutical industries.

Assuntos

RESUMO

In recent years, polymeric materials have been gaining prominence in studies of controlled release systems to obtain improvements in drug administration. These systems present several advantages compared with conventional release systems, such as constant maintenance in the blood concentration of a given drug, greater bioavailability, reduction of adverse effects, and fewer dosages required, thus providing a higher patient compliance to treatment. Given the above, the present work aimed to synthesize polymeric matrices derived from polyethylene glycol (PEG) capable of promoting the controlled release of the drug ketoconazole in order to minimize its adverse effects. PEG 4000 is a widely used polymer due to its excellent properties such as hydrophilicity, biocompatibility, and non-toxic effects. In this work, PEG 4000 and derivatives were incorporated with ketoconazole. The morphology of polymeric films was observed by AFM and showed changes on the film organization after drug incorporation. In SEM, it was possible to notice spheres that formed in some incorporated polymers. The zeta potential of PEG 4000 and its derivatives was determined and suggested that the microparticle surfaces showed a low electrostatic charge. Regarding the controlled release, all the incorporated polymers obtained a controlled release profile at pH 7.3. The release kinetics of ketoconazole in the samples of PEG 4000 and its derivatives followed first order for PEG 4000 HYDR INCORP and Higuchi for the other samples. Cytotoxicity was determined and PEG 4000 and its derivatives were not cytotoxic.

RESUMO

Recently, the development of materials with antimicrobial properties has become a challenge under scrutiny. The incorporation of copper nanoparticles (NpCu) into a chitosan matrix appears to represent a viable strategy to contain the particles and prevent their oxidation. Regarding the physical properties, the nanocomposite films (CHCu) showed a decrease in the elongation at break (5 %) and an increase in the tensile strength of 10 % concerning chitosan films (control). They also showed solubility values lower than 5 % while the swelling diminished by 50 %, on average. The dynamical mechanical analysis (DMA) of nanocomposites revealed two thermal events located at 113° and 178 °C, which matched the glass transitions of the CH-enriched phase and nanoparticles-enriched phase, respectively. In addition, the thermogravimetric analysis (TGA) detected a greater stability of the nanocomposites. Chitosan films and the NpCu-loaded nanocomposites demonstrated excellent antibacterial capacity against Gram-negative and Gram-positive bacteria, proved through diffusion disc, zeta potential, and ATR-FTIR techniques. Additionally, the penetration of individual NpCu particles into bacterial cells and the leakage of cell content were verified by TEM. The mechanism of the antibacterial activity of the nanocomposites involved the interaction of chitosan with the bacterial outer membrane or cell wall and the diffusion of the NpCu through the cells. These materials could be applied in diverse fields of biology, medicine, or food packaging.

Assuntos

RESUMO

To simultaneously form films while synthesizing solvent-free and catalyst-free bio-based polyurethanes, hexamethylene diisocyanate trimer was selected as an isocyanate group source to produce a low-viscosity reaction medium for dispersing high contents of microcrystalline cellulose (MCC, polyol) and cellulose nanocrystals (CNC). Castor oil was used as an additional polyol source. Up to 80 % of the MCC was dispersed, producing a film exhibiting the highest Tg (72 °C), tensile strength (18 MPa), and Young's modulus (522.4 MPa). 12.5 % (30 % MCC) and 7.5 % (50 % MCC) of CNC dispersed in the reaction medium formed films stiffer than their counterparts. All the films exhibited transparency and high crystallinity. The contact angle/zeta potential (ζ) indicated hydrophobic film surfaces. At pH 7.4, ζ suggested that the films interacted with physiological fluids favorably. The films were non-cytotoxic, and the composites exhibited cell growth compared with the control. The reported results, as far as it is known, are unprecedented.

Assuntos

RESUMO

Chitosan particles loaded with dibasic calcium phosphate anhydrous (DCPA) is a promising strategy for combining antimicrobial and osteoconduction properties in regenerative medicine. However, mostly micrometer-sized particles have been reported in the literature, limiting their use and reducing their effect in the biomedical field. We have recently overcome this limitation by developing submicrometer-sized particles with electrospray technique. The objective of this study was to understand how the process parameters control the size and properties of submicrometer chitosan particles loaded with DCPA. Solutions of 10 mg/mL chitosan and 2.5 mg/mL DCPA in a 90% acetic acid were electrosprayed under three distinct flow rate conditions: 0.2, 0.5, and 1.0 mL/h. The particles were crosslinked in a glutaraldehyde atmosphere and characterized in terms of their morphology, inorganic content, zeta potential, and minimum inhibitory concentration (MIC) against S. mutans. All conditions showed particles with two similar morphologies: one small-sized with a spherical shape and another larger-sized with a bi-concave shape. All generated a broad particle size distribution, with a similar mean size of ~ 235 nm. The addition of DCPA decreased the zeta potential for all the samples, but it was above 30 mV, indicating a low aggregation potential. The lower flow rate showed the worst efficacy for DCPA incorporation. Antimicrobial activity was greater in chitosan/DCPA particles with flow rate of 0.5 mL/h. It can be concluded that the flow rate of 0.5 mL/h presents the best compromise solution in terms of morphology, zeta potential, MIC, and inorganic content.

Assuntos

RESUMO

In this study functional properties of a galactose-rich heteropolysaccharide (GH) were accessed. The bands of a galactose-rich polysaccharide were found in FTIR spectra, including those from the fingerprint region. GH was characterized as a dark-red material (L* 25.86 ± 0.75, a* 9.46 ± 1.01, b* 0.65 ± 0.14, Chroma 9.48 ± 1.02) with antioxidant activity of 21.5 ± 0.08, 12.1 ± 0.06 and 0.46 ± 0.04 mmol Trolox Eq/mg GH in FRAP, DPPH and ABTS, respectively. GH presented 44.9% of esterification degree and 10.73 ± 0. 01 mg of GAE/g. The production parameters of GH emulsions (GH concentration, time and ultrasound power) were optimized using a 23 Central Composite Rotatable Design (CCRD). Emulsion droplets presented particle size (d µm) varying from 0.823 ± 0.065 to 1.926 ± 0.151, polydispersity index (PDI) from 0.10 ± 0.05 to 0.40 ± 0.01 and zeta potential from -29.25 ± 3.98 to -33.75 ± 1.77. Finally, the high emulsifying activity (EA) (96.67%) and emulsion stability (ES) (97.44%) allow suggesting that GH is a promising polysaccharide for food applications.

Assuntos

RESUMO

Lactoferrin (L), chitosan (C) and gellan (G) nanoparticles were produced by electrostatic complexation, aiming to enhance the antimicrobial characteristics of these compounds. Binary complexes (lactoferrin-gellan and chitosan-gellan) and ternary complexes (lactoferrin-chitosan-gellan) were studied in eight different proportions of biopolymers. The antimicrobial activity of nanoparticles against S. aureus was compared with that of pure biopolymers and related to nanoparticle size, charge density and morphology. Those with a 4.5L:4.5C:1G ratio presented the highest positive charge density (+57.90 ± 1.50) mV and smaller hydrodynamic diameter (53.53 ± 2.06) nm, which resulted in the highest antimicrobial action (minimum inhibitory concentration of 0.0117 mg/ml). When applied to a coating of fresh strawberries, the nanoparticles were effective in preserving their physicochemical properties, especially in the presence of carboxymethylcellulose that enhanced the adhesion of particles to the fruits. In this study, the antimicrobial action of nanoparticles was better than that of lactoferrin and pure chitosan alone, proving that the antimicrobial properties of such biopolymers were enhanced due to aggregation at the nanoscale. The nanoparticles produced have outstanding application potential as natural food preservers.

Assuntos

RESUMO

Objective: A critical analysis of the existing literature to answer "What is the influence of electrical charge of titanium alloys in the electrical interaction with osteoblastic cells for osseointegration?". Design: This systematic review followed PRISMA. The personalized search strategy was applied in PubMed, Science Direct, Embase, and Scopus databases, furthermore, in the grey literature in the Google Scholar and ProQuest. The selection process was carried out in two stages independently by two reviewers according to the eligibility criteria. The risk of bias was also analyzed. Results: When applying the search strategy, 306 articles were found, after removing duplicates 277 were analyzed by title and abstract, of which 33 were selected for full reading, of which 10 met the eligibility criteria. And one was included from the additional literature search. Of these, all had a low risk of bias. Conclusions: 1. The phenomenon of osseointegration is complex and, independent of the superficial electrical charge of the implant, it may occur. To understand osseointegration, attention must be paid to the synergistic action of the electrical potential; chemical composition, intrinsic to the alloy and from surface treatment; and topography, which will determine the speed of adhesion, proliferation, and osteoblast differentiation. 2. The presence of Ca2+ deposited on the surface acts as a driving force for biomineralization that induces osteoblastic attraction and differentiation; 3. For a better understanding of the current literature, more studies are needed to describe the osteogenic regulation process through protein mediation; 4. Topography and chemical composition act as decisive parameters for cell viability independent of the attractive electrical charge.

RESUMO

Vancomycin (VAN) is unable to penetrate the outer membrane of Gram-negative bacteria and reach the target site. One approach to overcome this limitation is to associate it with compounds with permeabilizing or antimicrobial properties. Eudragit E100® (Eu) is a cationic polymer insufficiently characterized for its potential antimicrobial action. Eu-VAN combinations were characterized, the antimicrobial efficacy against Pseudomonas aeruginosa was evaluated and previous studies on the effects of Eu on bacterial envelopes were extended. Time-kill assays showed eradication of P. aeruginosa within 3-6 h exposure to Eu-VAN, whilst VAN was ineffective. Eu showed regrowth in 24 h and delayed colony pigmentation. Although permeabilization of bacterial envelopes or morphological alterations observed by TEM and flow cytometry after exposure to Eu were insufficient to cause bacterial death, they allowed access of VAN to the target site, since Eu-VAN/Van-FL-treated cultures showed fluorescent staining in all bacterial cells, indicating Van-FL internalization. Consequently, Eu potentiated the activity of an otherwise inactive antibiotic against P. aeruginosa. Moreover, Eu-VAN combinations exhibited improved physicochemical properties and could be used in the development of therapeutic alternatives in the treatment of bacterial keratitis.

Assuntos

RESUMO

The search for new natural sources of hydrocolloids with stabilizing, thickening, and good binding capacity, from raw materials that are environmentally friendly and that contribute to the circular economy is a challenge for the food industry. The aim of the study was the preliminary characterization of a spray-dried hydrocolloid from high Andean algae Nostoc sphaericum. Four ecotypes of algae from Peruvian high Andean lagoons located above 4000 m were considered. The samples were collected in the period March−April 2021 and were subjected to a spray drying process in an aqueous medium. The characterization showed that the dehydrated nostoc ecotypes presented high protein and carbohydrate content, making it a potential material for direct use as a functional food for humans. The spray-dried product presented good stability for its use as a hydrocolloid, with zeta potential values (ζ), around 30 mV, evidencing the presence of -CO-, -OH, -COO-, and -CH groups, characteristic of polysaccharides, representing 40% of total organic carbon on average, giving it low water activity values and particle size at the nanometric level. Major minerals such as Ca (>277 mg/100 g), Mg (>19.7 mg/100 g), and Fe (>7.7 mg/100 g) were reported. Spray-dried nostoc is a hydrocolloid material with high potential for the food industry, with good nutritional content and techno-functional behavior.

RESUMO

Lactoferrin (L) and gellan gum (G) nanoparticles were produced in different biopolymer proportions through electrostatic complexation to enhance the antimicrobial properties of lactoferrin. The nanoparticles were characterized according to size, charge density, morphology and antimicrobial activity against S. aureus and E. coli, in two different broths to show the effect of the broth composition on the nanoparticle activity. The 9L:1G particles showed the highest positive zeta potential (+21.20 mV) and reduced diameter (92.03 nm) which resulted in a minimum inhibitory concentration six times smaller (0.3 mg/ml) than pure lactoferrin (2 mg/ml). However, the bacteriostatic action of nanoparticles was inhibited in the presence of divalent cations. When applied to strawberries as a coating, lactoferrin nanoparticles extended fruit shelf-life up to 6 days in the presence of carboxymethylcellulose (CMC). Therefore, lactoferrin-gellan gum complexation was proved to be a promising tool to enhance lactoferrin antimicrobial action and broaden its application as a food preserver.

RESUMO

Zeta potential and dipole potential measures are direct operational methodologies to determine the adsorption, insertion and penetration of ions, amphipathic and neutral compounds into the membranes of cells and model systems. From these results, the contribution of charged and dipole groups can be deduced. However, although each method may give apparent affinity or binding constants, care should be taken to interpret them in terms of physical meaning because they are not independent properties. On the base of a recent model in which the lipid bilayer is considered as composed by two interphase regions at each side of the hydrocarbon core, this review describes how dipole potential and zeta potential are correlated due to water reorganization. From this analysis, considering that in a cell the interphase region the membrane extends to the cell interior or overlaps with the interphase region of another supramolecular structure, the correlation of dipole and electrostatic forces can be taken as responsible of the propagation of perturbations between membrane and cytoplasm and vice versa. Thus, this picture gives the membrane a responsive character in addition to that of a selective permeability barrier when integrated to a complex system.

RESUMO

In this work, we report the synthesis of copper nanoparticles (Cu NPs), employing the chemical reduction method in an aqueous medium. We used copper sulfate pentahydrate (CuSO4·5H2O) as a metallic precursor; polyethylenimine (PEI), allylamine (AAM), and 4-aminobutyric acid (AABT) as stabilizing agents; and hydrated hydrazine as a reducing agent. The characterization of the obtained nanoparticles consisted of X-ray, TEM, FTIR, and TGA analyses. Through these techniques, it was possible to detect the presence of the used stabilizing agents on the surface of the NPs. Finally, a zeta potential analysis was performed to differentiate the stability of the nanoparticles with a different type of stabilizing agent, from which it was determined that the most stable nanoparticles were the Cu NPs synthesized in the presence of the PEI/AAM mixture. The antimicrobial activity of Cu/PEI/AABT toward P. aeruginosa and S. aureus bacteria was high, inhibiting both bacteria with low contact times and copper concentrations of 50-200 ppm. The synthesis method allowed us to obtain Cu NPs free of oxides, stable to oxidation, and with high yields. The newly functionalized Cu NPs are potential candidates for antimicrobial applications.

RESUMO

We aimed to determine the characteristics that distinguish glycosaminoglycans (GAGs) from osteoarthritis (OA) and normal cartilage and from men and women. Cartilage samples from 30 patients subjected to total joint arthroplasty secondary to OA or fracture (control) were evaluated, and the GAG content (µg/mg dry cartilage) after proteolysis was determined by densitometry, using agarose-gel electrophoresis. Relative percentages of carbon (C), nitrogen (N), and sulfur (S) in GAGs were determined by elemental microanalysis, as well as the zeta potential. Seventeen samples (56.6%) were from patients >70 years old, with 20 (66.6%) from women, and most [20 (66.6%)] were from the hip. The GAG content was similar regardless of patients being >/≤ 70 years old with 96.5 ± 63.5 and 78.5 ± 38.5 µg/mg (P = 0.1917), respectively. GAG content was higher in women as compared to men, with 89.5 ± 34.3 and 51.8 ± 13.3 µg/mg, respectively (P = 0.0022), as well as in OA than fracture samples, with 98.4 ± 63.5 and 63.6 ± 19.6 µg/mg, respectively (P = 0.0355). The GAG extracted from the cartilage of patients >70 years old had increase in N, and there were no gender differences regarding GAG elemental analysis. GAG from OA had a highly significant (P = 0.0005) decrease in S% (1.79% ± 0.25%), as compared to fracture samples (2.3% ± 0.19%), with an associated and significant (P = 0.0001) reduction of the zeta potential in the OA group. This is the first report of a reduced S content in GAG from OA patients, which is associated with a reduced zeta potential.

RESUMO

Anionic lipid membrane electrostatic potential and solution pH can influence cationic peptide adsorption to these bilayers, especially those containing simultaneously acid and basic residues. Here, we investigate the effects of the pH solution on MP1 (IDWKKLLDAAKQIL-NH2) adsorption to anionic (7POPC:3POPG) lipid vesicles in comparison to its analog H-MP1, with histidines substituting lysines. We used the association of adsorption isotherms and constant pH molecular dynamic simulations (CpHMD) to explore the effects of membrane potential and pH on peptides' adsorption on this lipid membrane. We analyzed the fluorescence and zeta potential adsorption isotherms using the Gouy-Chapman theory. In CpHMD simulations for the peptides in solution and adsorbed on the lipid bilayer, we used the conformations obtained by conventional MD simulations at a µs timescale. Non-equilibrium Monte Carlo simulations provided the protonation states of acidic and basic residues. CpHMD showed average pKa shifts of two to three units, resulting in a higher net charge for the analog than for MP1, strongly modulating the peptide adsorption. The fractions of the protonation of acidic and basic residues and the peptides' net charges obtained from the analysis of the adsorption isotherms were in reasonable agreement with those from CpHMD. MP1 adsorption was almost insensitive to solution pH. H-MP1 was much more sensitive to partitioning, at acidic pH, with an affinity ten times higher than in neutral ones.

RESUMO

This review summarizes the theory of zeta potential (ZP) and the most relevant data about how it has been used for studying bacteria. We have especially focused on the discovery and characterization of novel antimicrobial compounds. The ZP technique may be considered an indirect tool to estimate the surface potential of bacteria, a physical characteristic that is key to maintaining optimal cell function. For this reason, targeting the bacterial surface is of paramount interest in the development of new antimicrobials. Surface-acting agents have been found to display a remarkable bactericidal effect and have simultaneously revealed a low tendency to trigger resistance. Changes in the bacterial surface as a result of various processes can also be followed by ZP measurements. However, due to the complexity of the bacterial surface, some considerations regarding the assessment of ZP must first be taken into account. Evidence on the application of ZP measurements to the characterization of bacteria and biofilm formation is presented next. We finally discuss the feasibility of using the ZP technique to assess antimicrobial-induced changes in the bacterial surface. Among these changes are those related to the interaction of the agent with different components of the cell envelope, membrane permeabilization, and loss of viability.

Assuntos

RESUMO

The antimicrobial activities of plant extracts have formed the basis of many alternative medicines. In this context, the genus Schinus L. (Anacardiaceae), exhibits many traditional uses in medicine. However, a few studies on the antimicrobial properties of Schinus areira essential oils were conducted. The essential oil from S. areira leaves from Santiago del Estero was obtained by hydrodistillation and twenty-eight compounds were identified using CG-MS-EI spectrometry. The sesquiterpenoid alcohol 1-epi-cadinol was the major compound, followed by δ-cadinene, alloaromadendrene, ß-pinene, ß-caryophyllene, and γ-cadinene. The essential oil obtained exhibited antimicrobial activity against Staphylococcus aureus, showing a bacteriostatic activity at 64 µg/mL and bacteriolytic activity at 256 µg/mL; in contrast, non antibacterial effect was observed in Escherichia coli in the assayed conditions. The antibacterial activity was accompanied by significant changes in Zeta potential on the S. aureus surface. The data obtained suggest that the essential oil of S.areira leaves presents potential use in pharmaceutical industries.

Assuntos

RESUMO

Peperomia obtusifolia is a herbaceous perennial plant native to the Americas reported as a traditional medicine to treat snake bites and as a skin cleanser. The bioassay-guided fractionation of crude extracts from aerial parts of P. obtusifolia against a panel of clinically important fungi and bacteria, showed that hexane and dichloromethane extracts demonstrated selective bacterial inhibition, allowing the isolation of the known compounds peperobtusin A (1), and 3,4-dihydro-5-hydroxy-2,7-dimethyl-8-(3"-methyl-2"-butenyl)-2-(4'-methyl-1',3'-pentadienyl)-2H-1-benzopyran-6-carboxylic acid (2) from dichloromethane extract. Compound 2 was active against Gram-positive bacteria including community acquired methicillin-resistant Staphylococcus aureus (CA-MRSA) isolates and an Enterococcus faecalis vancomycin-resistant strain, with minimal inhibitory concentration (MIC) values of 4 µg/mL (10.8 µM) and 8 µg/mL (21.6 µM) respectively. The interaction of compound 2 with the bacterial membrane was demonstrated by means of Zeta potential experiments on S. aureus, then confirming the membrane damage by fluorescent microscopy experiments.

Assuntos