RESUMO
Gelatin have excellent film-forming and barrier properties, but its lack of biological activity limits its application in packaging. In this study, fish gelatin incorporated with apple polyphenol/cumin essential oil composite films were successfully prepared by melt extrusion. The cross-linking existed in gelatin and apple polyphenol improved the thermal stability and oxidation resistance of the film. The synergistic effect of apple polyphenols and cumin essential oil decreased the sensitivity of the film to water, especially the water solubility decreased from 41.60 % to 26.07 %. The plasticization of essential oil nearly doubled the elongation at break while maintaining the tensile strength of the film (11.45 MPa). Furthermore, the FG-CEO-AP film can inhibit peroxide value to extend the shelf life about 20 days in the walnut oil preservation. In summary, the apple polyphenol/cumin essential oil of FG film exhibits excellent comprehensive properties and high preparation efficiency for utilization as an active packaging material.
Assuntos
Embalagem de Alimentos , Gelatina , Juglans , Óleos de Plantas , Embalagem de Alimentos/instrumentação , Gelatina/química , Juglans/química , Óleos de Plantas/química , Óleos Voláteis/química , Resistência à Tração , Malus/química , SolubilidadeRESUMO
INTRODUCTION: Designing the microfluidic channel for neonatal drug delivery requires proper considerations to enhance the efficiency and safety of drug substances when used in neonates. Thus, this research aims to evaluate high-performance materials and optimize the channel design by modeling and simulation using COMSOL multiphysics in order to deliver an optimum flow rate between 0. 3 and 1 mL/hr. METHOD: Some of the materials used in the study included PDMS, glass, COC, PMMA, PC, TPE, and hydrogels, and the evaluation criterion involved biocompatibility, mechanical properties, chemical resistance, and ease of fabrication. The simulation was carried out in the COMSOL multiphysics platform and demonstrated the fog fluid behavior in different channel geometries, including laminar flow and turbulence. The study then used systematic changes in design parameters with the aim of establishing the best implementation models that can improve the efficiency and reliability of the drug delivery system. The comparison was based mostly on each material and its appropriateness in microfluidic usage, primarily in neonatal drug delivery. The biocompatibility of the developed materials was verified using the literature analysis and adherence to the ISO 10993 standard, thus providing safety for the use of neonatal devices. Tensile strength was included to check the strength of each material to withstand its operation conditions. Chemical resistance was also tested in order to determine the compatibility of the materials with various drugs, and the possibility of fabrication was also taken into consideration to identify appropriate materials that could be used in the rapid manufacturing of the product. RESULTS: The results we obtained show that PDMS, due to its flexibility and simplicity in simulation coupled with more efficient channel designs which have been extracted from COMSOL, present a feasible solution to neonatal drug delivery. CONCLUSION: The present comparative study serves as a guide on the choice of materials and design of microfluidic devices to help achieve safer and enhanced drug delivery systems suitable for the delicate reception of fragile neonates.
Assuntos
Sistemas de Liberação de Medicamentos , Desenho de Equipamento , Humanos , Recém-Nascido , Sistemas de Liberação de Medicamentos/instrumentação , Sistemas de Liberação de Medicamentos/métodos , Desenho de Equipamento/normas , Microfluídica/métodos , Microfluídica/instrumentação , Dispositivos Lab-On-A-Chip , Materiais Biocompatíveis/administração & dosagem , Resistência à Tração , Técnicas Analíticas Microfluídicas/instrumentação , Técnicas Analíticas Microfluídicas/métodosRESUMO
Hydrogels are highly sought-after absorbent materials for absorbent pads; however, it is still challenging to achieve a satisfactory balance between mechanical performance, water absorption capacity, and active functionalities. In this work, we presented double-network hydrogels synthesized through acrylic acid (AA) polymerization in the presence of quaternized cellulose nanofibrils (QCNF) and Fe3+. Spectroscopic and microscopic analyses revealed that the combined QCNF and Fe3+ facilitated the formation of double-network hydrogels with combined chemical and physical crosslinking. The synergistic effect of QCNF and Fe3+ resulted in impressive mechanical properties, including tensile strength of 1.98 MPa, fracture elongation of 838.8 %, toughness of 7.47 MJ m-3, and elastic modulus of 0.35 MPa. In comparison to the single-network PAA hydrogel, the PAA/QCNF/Fe3+ (PQFe) hydrogels showed higher and relatively stable swelling ratios under varying pH levels and saline conditions. The PQFe hydrogels exhibited notable antioxidant activity, as evidenced by the 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay, and demonstrated effective antibacterial activity against both Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). These hydrogels show promising potential as an absorbent interlayer in absorbent pads for active food packaging.
Assuntos
Resinas Acrílicas , Antibacterianos , Celulose , Escherichia coli , Hidrogéis , Ferro , Nanofibras , Staphylococcus aureus , Resistência à Tração , Hidrogéis/química , Hidrogéis/farmacologia , Celulose/química , Staphylococcus aureus/efeitos dos fármacos , Resinas Acrílicas/química , Escherichia coli/efeitos dos fármacos , Nanofibras/química , Ferro/química , Antibacterianos/farmacologia , Antibacterianos/química , Antioxidantes/química , Antioxidantes/farmacologia , Módulo de ElasticidadeRESUMO
Background: Over the past decade, 3D printing technology has revolutionized various fields, including dentistry. Provisional restorations play a crucial role in prosthetic rehabilitation, necessitating the evaluation of their bond strength with different provisional cement agents. Aims: This study is aimed at assessing the immediate and long-term bond strength of 3D-printed dental crowns using three provisional cement agents. Materials and Methods: Provisional crowns (N = 36) were manufactured using 3D modeling software and cemented in dentin analogues (G10 Nema resin). After the crowns' fabrication, they were randomly divided into three groups (n = 12) for cementation with Relyx Temp 3M ESPE, Provicol-VOCO, and Meron-VOCO. Tensile strength tests were conducted using a universal testing machine, with half of the specimens subjected to 2000 thermal cycles before testing. Finite element analysis was employed to assess tensile stress distribution. Results: Statistical analysis (two-way ANOVA and Tukey's test at a 95% confidence level) revealed significant effects of cement type (p = 0.006) and thermal aging (p = 0.001) on bond strength. Glass ionomer cement exhibited the highest immediate resistance, while all types of cement were adversely affected by thermal aging, resulting in decreased bond strength. Conclusion: Thermal aging significantly alters the properties of 3D printing resin and affects the bond strength of provisional cement with 3D-printed crowns. Despite the adverse effects of thermal aging, glass ionomer cement demonstrated the highest immediate resistance. Clinicians should carefully consider these findings when selecting provisional cements for 3D-printed crowns.
Assuntos
Coroas , Impressão Tridimensional , Resistência à Tração , Humanos , Teste de Materiais , Análise de Elementos Finitos , Cimentos de Ionômeros de Vidro/química , Cimentos Dentários/química , Colagem Dentária/métodosRESUMO
Determination of the cracking behavior during crack propagation helps to better understand damage and fracture processes in brittle rocks. The paper studies the cracking behavior of rocks on three scales: macro-deformation (or macro-cracking), internal micro-fracture, and surface crack coalescence. Under uniaxial compression, the cracking behavior of two types of sandstone specimens having single flaws was experimentally and systematically investigated. Acoustic emission (AE) and three-dimensional digital image correlation (3D-DIC) techniques were utilized to continuously monitor the acoustic shock signals generated by micro-fracture events inside the specimen and the specimen surface cracking process. The experimental results show that at the crack initiation stage, many micro-tensile fractures within the rock are initiated and coalesced, and small strain localized zones (SLZs) appear on the specimen surface. In the crack propagation stage, micro-fractures coalesce into macro-fractures that propagate in tensile mode to form surface cracks, which finally break in tension or slide against each other in shear mode. The formation of SLZs is related to the dip angle of pre-existing flaws, which determines the direction and mode of crack propagation. In conclusion, the strong acoustic-optical evidence accompanying different cracking behaviors is discussed in detail. From both acoustic and optical perspectives, it reveals and explains how flaws and material properties affect the strength and cracking mechanisms of brittle rocks. The study aids comprehension of the potential relation between internal micro-fracture and surface cracking in the process of engineering rock mass failure.
Assuntos
Acústica , Imageamento Tridimensional , Imageamento Tridimensional/métodos , Resistência à Tração , Estresse Mecânico , AreiaRESUMO
Evaluation of micro tensile bond strength (µTBS) and marginal leakage of sodium fluoride (NaF) and nano-hydroxyapatite (n-HA) modified universal adhesives (UAs) bonded using etch-and-rinse (ER) and self-etch (SE) bonding technique to the carious affected dentin (CAD). One hundred and twenty primary molars were prepared for CAD on the occlusal surface. The occlusal CAD surface was flattened and underwent a polishing procedure. The specimens were divided into six groups using a random allocation method based on the UAs applied and the mode of etching used (n = 20) Group A1: UAs (ER), Group B1: UAs (SE), Group A2: UAs (NaF) + ER, Group B2: UAs (NaF) + SE, Group A3: UA (n-HA) + ER and Group B3: UAs (n-HA) + SE. Composite restoration was placed and samples were thermocycled. Microleakage, µTBS, and failure mode assessment were performed using a dye penetration test, universal testing equipment, and stereomicroscope respectively. The µTBS and microleakage results (mean ± SD) were examined using analysis of the variance (ANOVA) and Tukey post hoc tests. Group B1 (UAs + SE) demonstrated the maximum scores of microleakage (25.14 ± 9.12 nm) and minimum recorded value of µTBS (14.16 ± 0.55 MPa). In contrast, Group A3 (UAs (n-HA) + ER) displayed a minimum value of marginal leakage (12.32 ± 6.33 nm) and maximum µTBS scores (19.22 ± 0.92 MPa). The outcomes of the intergroup comparison analysis showed that Group A2 (UAs (NaF) + ER), Group B2 (UAs (NaF) + SE), Group A3 (UA (n-HA) + ER) and Group B3 (UAs (n-HA) + SE) presented comparable outcomes of marginal seal outcomes and µTBS scores (p > 0.05). NaF and n-HA-modified UAs displayed favorable bond strength and minimum marginal leakage to the deciduous affected dentin surface.
Assuntos
Colagem Dentária , Cárie Dentária , Infiltração Dentária , Durapatita , Dente Molar , Nanopartículas , Fluoreto de Sódio , Resistência à Tração , Dente Decíduo , Humanos , Cárie Dentária/terapia , Durapatita/química , Colagem Dentária/métodos , Adesivos Dentinários/química , Teste de Materiais , Resinas Compostas/química , Cariostáticos , Cimentos DentáriosRESUMO
To investigate the effects of lactic acid etching on the immediate and aged bond strength of the resin-dentin bonding interface, the resin-dentin bonding interface was evaluated 24 hours and 6 months later. A total of 42 isolated third molars were randomly divided into 6 experimental groups according to different lactate concentration (35%, 40%, 45%) and acid etching time (30 s, 45 s), with 37% phosphoric acid etching 15 s as a control. In each group, dentin samples were etched under different acidic conditions and bonded with Adper Single Bond 2 (3M ESPE) as directed. The immediate group was immediately stored in deionized water at 37 °C for 24 h, and the aging group was stored in artificial saliva at 37 °C for 6 months. Immediate and aged bond strengths were measured by a micro-tensile tester, and the specimen fracture surface was observed under a microscope. 14 isolated third molars were randomly divided into 7 groups, and each group was etched with acid. Collagen fibers morphology in dentin was examined after gradient dehydration with ethanol by scanning electron microscopy (SEM). Statistically, there was no difference between the resin-dentin immediate bonding strength of 35% lactic acid for 30 s and 37% phosphoric acid for 15 s, but the aged bond strength was greater than that of the phosphoric acid group. According to scanning electron microscope observations, the collagen fiber morphology in 35% and 40% lactate etching dentin 30 s groups was relatively intact compared with other groups. In conclusion, 35% lactic acid etching of dentin 30 s ensures both immediate and aged resin-dentin bond strength.
Assuntos
Condicionamento Ácido do Dente , Colagem Dentária , Dentina , Ácido Láctico , Microscopia Eletrônica de Varredura , Resistência à Tração , Humanos , Ácido Láctico/química , Colagem Dentária/métodos , Condicionamento Ácido do Dente/métodos , Fatores de Tempo , Ácidos Fosfóricos/química , Adesivos Dentinários/química , Dente Serotino , Teste de Materiais , Análise do Estresse Dentário , Propriedades de Superfície , Cimentos de Resina/química , Cimentos DentáriosRESUMO
PURPOSE: To evaluate the long-term microtensile bond strength (µTBS) to dentin, water sorption (WSP) and solubility (WSL), and degree of conversion (DC) of self-adhesive resin composites (SACs). MATERIALS AND METHODS: The mid-coronal dentin of human molars was exposed, and teeth were randomly assigned to five groups according to the SACs (n = 10): 1. FIT SA F03 (FIT); 2. Experimental (EXP); 3. Fusio Liquid Dentin (FLD); 4. Vertise Flow (VER); 5. Constic (CON). The µTBS was evaluated after 24 hours (24 h) and 6 months (6 m) storage. A scanning electron microscope examined failure modes and resin-dentin interfaces. The WSP and WSL (n = 5) were evaluated following ISO 4049:2019 specifications, and DC (n = 3) was measured using Raman spectroscopy. The statistical analyses were performed accepting a significance level of p = 0.05. RESULTS: FIT, EXP, and FLD produced significantly higher µTBS median values than VER and CON after 24 h and 6 m (p 0.05). After 6m, the µTBS median of FIT and EXP significantly decreased (p 0.05), while FLD, VER, and CON showed no significant difference (p > 0.05). FLD and CON exhibited lower WSP than FIT, EXP, and VER (p 0.05). FLD presented the lowest (p 0.05), and VER revealed the highest WSL (p 0.05). FIT and EXP showed the highest (p 0.05), and VER demonstrated the lowest DC (p 0.05). CONCLUSIONS: Following the present study's design, SACs' bonding performance and physical properties remained restricted. Therefore, the application should be considered cautiously, and further clinical trials are necessary to evaluate their long-term performance.
Assuntos
Resinas Compostas , Colagem Dentária , Dentina , Teste de Materiais , Solubilidade , Resistência à Tração , Água , Resinas Compostas/química , Humanos , Água/química , Microscopia Eletrônica de Varredura , Adesivos Dentinários/química , Cimentos de Resina/química , Análise Espectral Raman , Fatores de Tempo , Propriedades de Superfície , Análise do Estresse DentárioRESUMO
Since aircraft icing will decrease the ability of aircraft to generate lift, it is significant to consider the aircraft deicing problem. The paper presents an aircraft deicing method based on the cracking of the ice layer caused by the large deformations of wings. To describe the deformation of wings, the absolute coordinate-based formulation is used. The aircraft with high aspect ratio wings is simplified as a hub-beam system. Such a rigid-flexible system with the fast rotation speed of hub and the large deformation of the beam is modeled using absolute coordinate-based formulation accurately. The maneuver of the rigid body will lead to the large deformation of wings to do the de-icing. Numerical examples are presented to reveal that the maximum tensile strength on the wing surface with sinusoidal control torques with some amplitudes and frequencies is larger than the ice's tensile strength. Hence, the proposed de-icing method based on the aircraft maneuvering is potential.
Assuntos
Aeronaves , Resistência à Tração , Vibração , Modelos TeóricosRESUMO
This study evaluated the effects of two chlorophyll derivatives, sodium copper chlorophyllin (Cu-Chl) and sodium iron chlorophyllin (Fe-Chl), on the bond strength between a self-curing luting agent (4-META/MMA-TBB resin) and dentin. Five aqueous primers containing 35% 2-hydroxyethylmethacrylate with 0.007% Cu-Chl, 0.07% Cu-Chl, 0.007% Fe-Chl, 0.07% Fe-Chl, or neither Cu-Chl nor Fe-Chl (no-Chl) were prepared. The extracted human dentin surfaces were etched with 10% phosphoric acid (10PA), primed, and bonded to a resin block using the 4-META/MMA-TBB resin. A conventional etching agent (10-3) and 10PA without primer (PA/no-primer) were used as controls. The microtensile bond strength was determined after 48 h. The arithmetic medians for 20 stick specimens were calculated and statistically analyzed using a nonparametric Steel-Dwass test (α = 0.05). The maximum bond strength was achieved in the 0.007% Cu-Chl group, followed by those in the 0.07% Cu-Chl, 0.07% Fe-Chl, 10-3, 0.007% Fe-Chl, no-Chl, and PA/no-primer groups. No significant difference was observed between 0.007% Fe-Chl, 0.07% Fe-Chl, and 10-3. The bond strength to dentin etched with 10PA was influenced by the type and concentration of the chlorophyll derivatives applied. Cu-Chl rather than Fe-Chl should be useful as a component of surface treatment agents for bonding 4-META/MMA-TBB resin to dentin.
Assuntos
Condicionamento Ácido do Dente , Clorofilídeos , Colagem Dentária , Adesivos Dentinários , Dentina , Teste de Materiais , Metacrilatos , Cimentos de Resina , Resistência à Tração , Humanos , Dentina/efeitos dos fármacos , Dentina/química , Metacrilatos/química , Adesivos Dentinários/química , Cimentos de Resina/química , Ácidos Fosfóricos/química , Compostos de Boro/química , Metilmetacrilatos/química , Propriedades de Superfície , Cobre/química , Fatores de Tempo , Análise do Estresse Dentário , Estresse Mecânico , Microscopia Eletrônica de VarreduraRESUMO
Partial or complete rupture of the tendon can damage the collagen structure, resulting in the disruption of the electrical signal pathway. It is a great challenge to reconstruct the original electrical signal pathway of the tendon and promote the regeneration and functional recovery of defective tendon. In this study, carbon fiber-mediated electrospinning scaffolds were fabricated by wrapping conductive, high-strength, loose single-bundle carbon fibers with nanofiber membranes. Due to the presence of nanofiber membranes, the maximum tensile force of the scaffolds was 2.4 times higher than that of carbon fibers, while providing excellent temporal and spatial prerequisites for tenocytes to adapt to electrical stimulation to accelerate proliferation and expression. The diameter of the carbon fiber monofilaments used in this study was 5.07 ± 1.20 µm, which matched the diameter of tendon collagen, allowing for quickly establishing the connection between the tendon tissue and the scaffold, and better promoting the recovery of the electrical signal pathway. In a rabbit Achilles tendon defect repair model, the carbon fiber-mediated electrospinning scaffold was almost filled with collagen fibers compared to a nonconductive polyethylene glycol terephthalate scaffold. Transcriptome sequencing revealed that fibromodulin and tenomodulin expression were upregulated, and their related proteoglycans and glycosaminoglycan binding proteins pathways were enhanced, which could regulate the TGF-ß signaling pathway and optimize the extracellular matrix assembly, thus promoting tendon repair. Therefore, the scaffold in this study makes up for the shortage of conductive scaffolds for repairing tendon defects, revealing the potential impact of conductivity on the signaling pathway of tendon repair and providing a new approach for future clinical studies.
Assuntos
Fibra de Carbono , Alicerces Teciduais , Animais , Alicerces Teciduais/química , Coelhos , Fibra de Carbono/química , Engenharia Tecidual , Nanofibras/química , Traumatismos dos Tendões/terapia , Traumatismos dos Tendões/patologia , Tendão do Calcâneo/patologia , Tendão do Calcâneo/química , Tendão do Calcâneo/lesões , Tenócitos/metabolismo , Tenócitos/efeitos dos fármacos , Tendões/patologia , Tendões/metabolismo , Colágeno/química , Eletricidade , Resistência à TraçãoRESUMO
Bone defect repair and postoperative infections are among the most challenging issues faced by orthopedic surgeons. Thus, the antibacterial agent Cu and the osteogenic promoter Sr have been widely incorporated into biodegradable alloys separately. However, to the best of our knowledge, the synergistic effects of Cu and Sr on zinc alloys have not been investigated. Therefore, we have developed a series of novel Zn-4Cu-xSr (x = 0.05, 0.1, and 0.3 wt %) alloys. Our results showed that the addition of Cu and Sr significantly increased the strength of pure zinc while maintaining a certain level of ductility. Plastic deformation further enhanced the strength and ductility of the alloys. The tensile strength of HR Zn-4Cu-xSr alloys remains between 233.34 ± 1.31 MPa and 235.81 ± 3.0 MPa, with elongation values ranging from 45.7 ± 1.56% to 49.6 ± 6.22%. The HE Zn-4Cu-0.05Sr alloy exhibits a high elongation of 95.05 ± 11.1%. Furthermore, the HE Zn-4Cu-0.1Sr alloy demonstrates the best overall mechanical performance with ultimate tensile strength (σuts), yield strength (σys), and elongation (ε) values of 252.73 ± 0.12 MPa, 181.0 ± 0.79 MPa, and 42.8 ± 1.13%, respectively. The corrosion rate of HE Zn-4Cu-xSr alloys increases with an increase in Sr content. All samples exhibit satisfactory cytocompatibility with the cells displaying a healthy spindle-like morphology. In vitro antibacterial tests show that the HE Zn-4Cu-xSr alloys exhibit significant antibacterial effects against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), with the antibacterial properties strengthening as the Sr content increases. Therefore, this study demonstrates the tremendous potential application of Zn-4Cu-xSr alloys in biodegradable zinc alloys for bone fracture fixation and repair.
Assuntos
Ligas , Cobre , Estrôncio , Resistência à Tração , Zinco , Ligas/química , Ligas/farmacologia , Zinco/química , Zinco/farmacologia , Cobre/química , Cobre/farmacologia , Estrôncio/química , Estrôncio/farmacologia , Antibacterianos/farmacologia , Antibacterianos/química , Materiais Biocompatíveis/química , Materiais Biocompatíveis/farmacologia , Teste de Materiais , Humanos , Staphylococcus aureus/efeitos dos fármacos , Escherichia coli/efeitos dos fármacosRESUMO
Optimizing the regeneration process of surgically created anastomoses (blood vessels, intestines, nerves) is an important topic in surgical research. One of the most interesting parameter groups is related to the biomechanical properties of the anastomoses. Depending on the regeneration process and its influencing factors, tensile strength and other biomechanical features may change during the healing process. Related to the optimal specimen size, the range and accuracy of measurements, and applicability, we have developed a custom-tailored microcontroller-based device. In this paper, we describe the hardware and software configuration of the latest version of the device, including experiences and comparative measurements of tensile strength and elasticity of artificial materials and biopreparate tissue samples. The machine we developed was made up of easily obtainable parts and can be easily reproduced on a low budget. The basic device can apply a force of up to 40 newtons, and can grasp a 0.05-1 cm wide, 0.05-1 cm thick tissue. The length of the test piece on the rail should be between 0.3 and 5 cm. Low production cost, ease of use, and detailed data recording make it a useful tool for experimental surgical research.
Assuntos
Anastomose Cirúrgica , Elasticidade , Intestinos , Resistência à Tração , Intestinos/fisiologia , Anastomose Cirúrgica/instrumentação , Regeneração/fisiologia , Animais , Humanos , Vasos Sanguíneos/fisiologia , Fenômenos Biomecânicos/fisiologiaRESUMO
Conductive hydrogels have been increasingly employed to construct wearable mechanosensors due to their excellent mechanical flexibility close to that of soft tissues. In this work, piezoelectric hydrogels are prepared through free radical copolymerization of acrylamide (AM) and acrylonitrile (AN) and further utilized in assembling flexible wearable mechanosensors. Introduction of the polyacrylonitrile (PAN) component in the copolymers endows the hydrogels with excellent piezoelectric properties. Meanwhile, significant enhancement of mechanical properties has been accessed by forming dipole-dipole interactions, which results in a tensile strength of 0.51 MPa. Flexible wearable mechanosensors are fabricated by utilizing piezoelectric hydrogels as key signal converting materials. Self-powered piezoelectric pressure sensors are assembled with a sensitivity (S) of 0.2 V kPa-1. Additionally, resistive strain sensors (gauge factor (GF): 0.84, strain range: 0-250%) and capacitive pressure sensors (S: 0.23 kPa-1, pressure range: 0-8 kPa) are fabricated by utilizing such hydrogels. These flexible wearable mechanosensors can monitor diverse body movements such as joint bending, walking, running, and stair climbing. This work is anticipated to offer promising soft materials for efficient mechanical-to-electrical signal conversion and provides new insights into the development of various wearable mechanosensors.
Assuntos
Resinas Acrílicas , Hidrogéis , Dispositivos Eletrônicos Vestíveis , Hidrogéis/química , Resinas Acrílicas/química , Humanos , Resistência à Tração , Acrilamida/químicaRESUMO
OBJECTIVES: The aim of this study was to evaluate, in vitro, the load and type of failure of the sutured ventral abdominal fascia of cats with different sizes of suture material made of polydioxanone (PDX) (2-0, 3-0, 4-0, 5-0 USP). METHODS: A total of 32 samples of the ventral abdominal wall from 16 cadaveric cats were harvested using an hourglass-shaped template. The samples were sectioned longitudinally along the linea alba and then sutured together in a continuous pattern using four different randomly assigned sizes of pdx suture material (2-0, 3-0, 4-0, 5-0 USP). A universal testing machine was used for linear distraction of the samples. The tensile strength and type of failure were recorded and analysed. Three types of failure were defined: suture material failure (S), suture line failure (T1) and failure of the abdominal wall further away from the linea alba (T2). RESULTS: The frequency of suture material failure decreased with increasing suture size. Suture size 5-0 failed due to a S failure in 6/8 samples, PDX 4-0 failed in 2/8 samples and PDX 3-0 failed in only 1/8 samples. However, PDX 2-0 failed due to only T1 or T2 failures, with both failures being almost equally represented. No statistically significant differences in the load to failure between PDX 2-0, 3-0 and 4-0 were noted (P >0.05). The risk of suture failure increased with decreasing suture size diameter. CONCLUSIONS AND RELEVANCE: PDX 2-0 and 3-0 can be used without reservation for the closure of ventral midline coeliotomy in cats. Although there was no statistically significant difference between PDX 2-0, 3-0 and 4-0, PDX 4-0 showed a higher probability for suture breakage and should be used only after careful consideration of the patient while clinical evaluation is pending. Pdx 5-0 cannot be recommended as a safe suture size for this type of surgical closure.
Assuntos
Polidioxanona , Técnicas de Sutura , Suturas , Resistência à Tração , Animais , Gatos , Suturas/veterinária , Técnicas de Sutura/veterinária , Fenômenos Biomecânicos , Parede Abdominal/cirurgia , Teste de Materiais/veterinária , CadáverRESUMO
In this study, significant improvements in mechanical properties have been seen through the efficient inclusion of Oil Palm Cellulose Nanofibrils (CNF) as nano-fillers into green polymer matrices produced from biomass with a 28 % carbon content. The goal of the research was to make green epoxy nanocomposites utilizing solution blending process with acetone as the solvent with the different CNF loadings (0.1, 0.25, and 0.5 wt%). An ultrasonic bath was used in conjunction with mechanical stirring to guarantee that CNF was effectively dispersed throughout the green epoxy. The resultant nanocomposites underwent thorough evaluation, comparing them to unfilled green epoxy and evaluating their morphological, mechanical, and thermal behavior using a variety of instruments. Field-emission scanning electron microscopy (FE-SEM) was used to validate findings, which showed that the CNF were dispersed optimally inside the nanocomposites. The thermal degradation temperature (Td) of the nanocomposites showed a marginal decrement of 0.8 % in temperatures (from 348 °C to 345 °C), between unfilled green epoxy (neat) and 0.1 wt% of CNF loading. The mechanical test results, which showed a 13.3 % improvement in hardness and a 6.45 % rise in tensile strength when compared to unfilled green epoxy, were in line with previously published research. Overall, the outcomes showed that green nanocomposites have significantly improved in performance.
Assuntos
Celulose , Nanocompostos , Nanofibras , Nanocompostos/química , Celulose/química , Nanofibras/química , Temperatura , Resinas Epóxi/química , Resistência à Tração , Química Verde/métodos , Óleo de Palmeira/química , Fenômenos MecânicosRESUMO
Sustainable poly (lactic acid) (PLA) with excellent strength, toughness, heat resistance, transparency, and biodegradability was achieved by uniaxial pre-stretching at 70 °C. The effect of pre-stretched ratio (PSR) on the microstructure and properties of the PLA was investigated. The undrawn PLA was brittle. However, after pre-stretching, the elongation at break was increased significantly. The maximum value of 161.2 % was obtained at pre-stretching ratio (PSR) of 1.0. With the increase of PSR, the modulus and strength were improved obviously (from 1601 MPa and 60.2 MPa for undrawn PLA to 2932 MPa and 106.3 MPa for the ps-PLA at PSR =3.0). Meanwhile, the heat resistance of PLA was improved obviously with the increase of PSR. For the ps-PLA3.0, there were almost no deformation and shrink at 140 °C. Interestingly, after pre-stretching, the PLA still maintained the good transparency and biodegradability. The brittleness for undrawn PLA was attributed to the network structure of cohesional entanglements. After pre-stretching, the destruction of the network structure and formation of the orientation, mesophase and oriented nanosized crystalline phase lead to the increased the toughness, strength and heat resistance without sacrificing the transparency and biodegradability. This work provides a significant guidance for the fabrication of PLA material with excellent comprehensive performance including strength, toughness, heat resistance, transparency, and biodegradability.
Assuntos
Temperatura Alta , Poliésteres , Poliésteres/química , Resistência à Tração , Teste de Materiais , Fenômenos MecânicosRESUMO
Fucosterols have been widely studied for their antioxidant, anticancer, and anti-inflammatory properties. However, they have not yet been studied in the field of dentistry. This study aimed to determine whether pretreatment of dentin with fucosterol before resin restoration enhances bond stability in resin-dentin hybrid layers. After applying 0.1, 0.5, and 1.0 wt% fucosterol to demineralized dentin, microtensile bond strength (MTBS) and nanoleakage tests were performed before and after collagenase aging, and the surface was observed using scanning electron microscope (SEM). The fucosterol-treated group showed better bond strength and less nanoleakage both before and after collagenase aging, and the corresponding structures were confirmed using SEM. MMP zymography confirmed that the activity of MMPs was relatively low along the concentration gradient of fucosterol, and the FTIR analysis confirmed the production of collagen crosslinks. In addition, fucosterol exhibits cytotoxicity against Streptococcus mutans, the main cause of dental decay. The results of this study suggest that fucosterol pretreatment improves bond strength and reduces nanoleakage at the resin-dentin interface, possibly through a mechanism involving collagen cross-link formation via the inhibition of endogenous and exogenous MMP activity. This study demonstrates the potential of fucosterol as an MMP inhibitor in dentin, which contributes to long-term resin-dentin bond stability and can be used as a restorative material.
Assuntos
Dentina , Inibidores de Metaloproteinases de Matriz , Estigmasterol , Humanos , Dentina/metabolismo , Dentina/química , Inibidores de Metaloproteinases de Matriz/farmacologia , Inibidores de Metaloproteinases de Matriz/química , Estigmasterol/farmacologia , Estigmasterol/análogos & derivados , Estigmasterol/química , Resistência à Tração , Metaloproteinases da Matriz/metabolismo , Colagem Dentária , Streptococcus mutans/efeitos dos fármacos , Fenômenos Biomecânicos , Adesivos Dentinários/química , Adesivos Dentinários/farmacologiaRESUMO
To investigate the advantageous effects of incorporating industrial solid waste basic oxygen furnace (BOF) slag on the mechanical characteristics of warm-mixed rubber asphalt (WMRA) and hot-mixed rubber asphalt (HMRA) mixture, varying proportions of BOF slag were substituted for limestone coarse aggregates (0%, 25%, 50%, and 75%). Additionally, a 1.5% dosage of Sasobit warm-mixed modifier was introduced to prepare the rubber asphalt. Subsequent to preparation, both static mechanical tests (including Marshall and indirect tensile tests) and dynamic mechanical tests (including dynamic creep and elastic modulus tests) were conducted to evaluate the influence of BOF slag on the mechanical behavior of WMRA and HMRA mixtures across different substitution levels. Following testing, a two-way analysis of variance (ANOVA) was employed to dissect the impact of BOF slag content and Sasobit warm-mixed modifier on the static and dynamic mechanical properties of the rubber asphalt mixtures. The findings reveal that BOF slag exhibits commendable engineering aggregate properties, enabling substantial substitution of coarse aggregates in both HMRA and WMRA mixtures. As the proportion of BOF slag increases, it enhances the resistance of asphalt mixtures to permanent deformation and cracking under static and dynamic loading conditions, while broadening the range of elastic deformation for both WMRA and HMRA mixtures subjected to repeated loading. Moreover, a synergistic enhancement in the resistance of rubber asphalt mixtures to dynamic load-induced deformation is observed when employing both BOF slag and Sasobit warm-mixed modifier. The findings offer valuable insights for enhancing the performance of WMRA and HMRA mixtures, as well as broadening the utilization of BOF slag and waste rubber.
Assuntos
Hidrocarbonetos , Borracha , Borracha/química , Hidrocarbonetos/química , Oxigênio/química , Teste de Materiais , Resistência à Tração , Resíduos Industriais , Módulo de ElasticidadeRESUMO
Despite recent advancements, artificial muscles have not yet been able to strike the right balance between exceptional mechanical properties and dexterous actuation abilities that are found in biological systems. Here, we present an artificial magnetic muscle that exhibits multiple remarkable mechanical properties and demonstrates comprehensive actuating performance, surpassing those of biological muscles. This artificial muscle utilizes a composite configuration, integrating a phase-change polymer and ferromagnetic particles, enabling active control over mechanical properties and complex actuating motions through remote laser heating and magnetic field manipulation. Consequently, the magnetic composite muscle can dynamically adjust its stiffness as needed, achieving a switching ratio exceeding 2.7 × 10³. This remarkable adaptability facilitates substantial load-bearing capacity, with specific load capacities of up to 1000 and 3690 for tensile and compressive stresses, respectively. Moreover, it demonstrates reversible extension, contraction, bending, and twisting, with stretchability exceeding 800%. We leverage these distinctive attributes to showcase the versatility of this composite muscle as a soft continuum robotic manipulator. It adeptly executes various programmable responses and performs complex tasks while minimizing mechanical vibrations. Furthermore, we demonstrate that this composite muscle excels across multiple mechanical and actuation aspects compared to existing actuators.