RESUMO

Nanocellulose (NC) is a promising material for drug delivery due to its high surface area-to-volume ratio, biocompatibility, biodegradability, and versatility in various formats (nanoparticles, hydrogels, microspheres, membranes, and films). In this study, nanocellulose films were derived from "Bolaina blanca" (Guazuma crinita) and combined with nanoporous silicon microparticles (nPSi) in concentrations ranging from 0.1% to 1.0% (w/v), using polyvinyl alcohol (PVA) as a binding agent to create NC/nPSi composite films for drug delivery systems. The physicochemical properties of the samples were characterized using UV-Vis spectroscopy, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The mechanical properties and drug release capabilities were also evaluated using methylene blue (MB) as an antibacterial drug model. Antibacterial assays were conducted against S. aureus and E. coli bacteria. The results show that NC/nPSi composites with 1% nPSi increased the T50% by 10 °C and enhanced mechanical properties, such as a 70% increase in the elastic modulus and a 372% increase in elongation, compared to NC films. Additionally, MB released from NC/nPSi composites effectively inhibited the growth of both bacteria. It was also observed that the diffusion coefficients were inversely proportional to the % nPSi. These findings suggest that this novel NC/nPSi-based material can serve as an effective controlled drug release system.

RESUMO

Wood-plastic composites are becoming increasingly recognized for their sustainability and their potential for use in various production processes. Nevertheless, enhancing their mechanical strength continues to be a difficult challenge. The objective of this research was to improve the mechanical strength of wood-plastic composite components manufactured through selective laser sintering (SLS). This was achieved by integrating a sustainable composite material, Prosopis chilensis (PCP), with polyethersulfone (PES) to form a composite referred to as PCPC. This study showcased the effect of various PCP particle sizes on mechanical strengths, dimensional accuracies (DAs), and surface roughness of PCPC parts manufactured using AFS-360 SLS. Single-layer sintering was employed to assess PCPC powder's formability with varying PCP particle sizes, and various tests were conducted to understand the materials' thermal properties and analyze particle dispersion and microstructure. The results demonstrated that PCP particle sizes ≤ 0.125 mm significantly enhanced the mechanical strength, forming quality, and DA compared to other particle sizes and pure PES. Key findings for PCPC parts with PCP ≤ 0.125 mm included a bending strength of 10.78 MPa, a tensile strength of 4.94 MPa, an impact strength of 0.91 kJ/m2, and a density of 1.003 g/cm3. Post-processing further improved these parameters, confirming that optimizing PCP particle size is crucial for enhancing the mechanical properties and overall quality of PCPC parts produced via SLS.

RESUMO

When the cocoa pod husk (CPH) is used and processed, two types of flour were obtained and can be differentiated by particle size, fine flour (FFCH), and coarse flour (CFCH) and can be used as a possible reinforcement for the development of bio-based composite materials. Each flour was obtained from chopping, drying by forced convection, milling by blades, and sieving using the 100 mesh/bottom according to the Tyler series. Their physicochemical, thermal, and structural characterization made it possible to identify the lower presence of lignin and higher proportions of cellulose and pectin in FFCH. Based on the properties identified in FFCH, it was included in the processing of thermoplastic starch (TPS) from the plantain pulp (Musa paradisiaca) and its respective bio-based composite material using plantain peel short fiber (PPSF) as a reinforcing agent using the following sequence of processing techniques: extrusion, internal mixing, and compression molding. The influence of FFCH contributed to the increase in ultimate tensile strength (7.59 MPa) and higher matrix-reinforcement interaction when obtaining the freshly processed composite material (day 0) when compared to the bio-based composite material with higher FCP content (30%) in the absence of FFCH. As for the disadvantages of FFCH, reduced thermal stability (323.57 to 300.47 °C) and losses in ultimate tensile strength (0.73 MPa) and modulus of elasticity (142.53 to 26.17 MPa) during storage progress were identified. In the case of TPS, the strengthening action of FFCH was not evident. Finally, the use of CFCH was not considered for the elaboration of the bio-based composite material because it reached a higher lignin content than FFCH, which was expected to decrease its affinity with the TPS matrix, resulting in lower mechanical properties in the material.

RESUMO

A completely biobased composite material was developed using a matrix of natural resin extracted from the Elaegia pastoensis Mora plant, commonly known as Mopa-Mopa or "Barniz de Pasto", reinforced with fibers extracted from plantain rachis agricultural residues. A solvent process, involving grinding, distillation, filtration, and drying stages, was implemented to extract the resin from the plant bud. To obtain the resin from the plant bud, the vegetable material was ground and then dissolved in a water-alcohol blend, followed by distillation, filtration, and grinding until the powdered resin was ready for use in the preparation of the biocomposite. Likewise, using mechanical techniques, the plantain rachis fibers were extracted and worked in their native condition and with a previous alkalinization surface treatment. Finally, the biocomposite material was developed with and without incorporating stearic acid, which was included to reduce the material's moisture absorption. Ultimately stearic acid was used as an additive to reduce biocomposite moisture absorption. The tensile mechanical results showed that the Mopa-Mopa resin reached a maximum strength of 20 MPa, which decreased with the incorporation of the additive to 12 MPa, indicating its plasticization effect. Likewise, slight decreases in moisture absorption were also evidenced with the incorporation of stearic acid. With the inclusion of rachis plantain fibers in their native state, a reduction in the tensile mechanical properties was found, proportional to the amount added. On the other hand, with the alkalinization treatment of the fibers, the behavior was the opposite, evidencing increases in tensile strength, indicating that the fiber modification improved the interfacial adhesion with the Mopa-Mopa matrix. On the other hand, the evaluation of the moisture absorption of the biocomposite material evidenced, as expected, that the absorption level was favored by the relative humidity used in the conditioning (47, 77, and 97%), which also had an impact on the decrease of the mechanical tensile properties, being this was slightly counteracted by the inclusion of stearic acid in the formulation of the material.

RESUMO

The development of wind turbines for regions with low wind speeds imposes a challenge to the expansion of the corresponding energy generation capacity. The present work consists of an evaluation of the potential carded jute fiber and jute yarn to be used in the construction of a wind blade for regions of low wind intensity. The fibers used were supplied by Company Textile of Castanhal (Castanhal-Para-Brazil) and used in the study without chemical treatment in the form of single-filament fibers and yarns with a surface twist of 18.5°. The composites were produced through the resin infusion technique and underwent tensile and shear tests using 120-Ohm strain gauges and a blade extensometer to obtain the Young's modulus. In the analysis of the results, the ANOVA test was applied with a 0.05 significance level, followed by Tukey's test. The results showed that long, aligned jute fibers can be a good option for laminated structures applied in composites for small wind turbine blades.

RESUMO

Acute myocardial infarction (AMI) is the main cause of death worldwide, and the time of diagnosis is decisive for the effectiveness of the treatment of patients with AMI. Creatine kinase-myocardial band (CK-MB) has a predominance and high affinity with myocardial tissue, making it considered one of the main biomarkers for the diagnosis of AMI. In this work, we report a novel biodegradable composite material based on a polymer blend of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and Poly(butylene adipate-co-terephthalate) (PHBV:Ecoflex) and graphite microparticles for sensitive and selective electrochemical detection of CK-MB. The morphological and physicochemical characterizations of the thermoplastic composite material revealed a homogeneous and synergistic distribution of the graphite microparticles through the blend structure, providing low defects and high electrical conductivity with high electron transfer kinetics (k0 = 3.54 × 10-3 cm s-1) features with adequate flexibility for point-of-care applications. The portable and disposable devices were applied to detect CK-MB using the electrochemical impedance spectroscopy (EIS) technique in a relevant clinical concentration ranging from 5.0 ng mL-1 to 100.0 ng mL-1 and presented a limit of detection of 0.26 ng mL-1 CK-MB. The selectivity of the sensor was confirmed by testing the potential interference of major biomolecules found in biofluids and other relevant macromolecules. The accuracy and robustness were assessed by addition and recovery protocol in urine and saliva samples without sample pretreatment and demonstrated the potential of our method for rapid and decentralized tests of AMI. In addition, the study of the thermal, biological, and photodegradation of the devices after being used was also carried out, aiming at the disposal of the material more sustainably.

Assuntos

Grafite , Infarto do Miocárdio , Humanos , Creatina Quinase , Sensibilidade e Especificidade , Sistemas Automatizados de Assistência Junto ao Leito , Infarto do Miocárdio/diagnóstico , Biomarcadores , Eletrodos

RESUMO

In this work, the development of a disposable electrochemical device (US$ 0.02 per electrode) using a 3D printed support (3Ds) of acrylonitrile butadiene styrene (ABS) insulating filament with a composite material (CM) based on graphite and nail polish, immobilized on the support surface, was described for the electrochemical determination of diclofenac (DCF). The device was compared to the commercial glassy carbon electrode (GCE) and showed superior electroanalytical performance with approximately 1.8-fold higher current density. Additionally, an amperometric method for DCF determination in tap water, synthetic urine, and pharmaceutical formulation samples with the proposed electrode, using a flow injection analysis (FIA-AD) system, was developed. The optimized method presented excellent detectability (LOD = 0.47 µmol L-1), with excellent precision and accuracy (relative standard deviation < 5.6%) and percent recovery from spiked samples ranging from 89 to 106%. In addition, the sensor showed optimal analytical frequency with approximately 108 injections per hour, which demonstrates the potential of this system using the proposed disposable electrode for implementation in routine analysis and quality control with good selectivity and sensitivity.

Assuntos

Diclofenaco , Grafite , Diclofenaco/análise , Carbono , Água , Eletrodos , Técnicas Eletroquímicas/métodos

RESUMO

Composite materials based on titania nanoparticles (TiO2 NPs) and three metal-organic frameworks (MOFs) called MIL-53 (Fe) ((Fe (III) (OH) (1,4-BDC)), MILs (Materials Institute Lavoisier)), MIL-100 (Fe) (Fe3O(H2O)2OH(BTC)2), and Fe-BTC (iron-benzenetricarboxylate) with different percentages of TiO2 NPs (0.5, 1, and 2.5% wt.) were synthesized using the solvothermal method and used as photocatalytic materials in the degradation of two dyes (Orange II and Reactive Black 5 (RB5)). The pristine and composite materials were characterized with X-ray diffraction, Raman, UV-Vis and Fourier transform infrared spectroscopy and scanning electron microscopy techniques. The 2.5TiO2/MIL-100 composite material showed the best results for the degradation of both dyes (Reactive Black 5 and Orange II dye, 99% and 99.5% degradation in 105 and 150 min, respectively). The incorporation of TiO2 NPs into MOFs can decrease the recombination of the change carrier in the MOF, increasing the photocatalytic activity of a pristine MOF. Results therefore indicated that the synthesized MOF nanocomposites have good potential for wastewater treatment.

Assuntos

Estruturas Metalorgânicas , Nanopartículas , Corantes/química , Ferro/química , Estruturas Metalorgânicas/química

RESUMO

The thermal stability of natural fiber composites is a relevant aspect to be considered since the processing temperature plays a critical role in the manufacturing process of composites. At higher temperatures, the natural fiber components (cellulose, hemicellulose, and lignin) start to degrade and their major properties (mechanical and thermal) change. Different methods are used in the literature to determine the thermal properties of natural fiber composites as well as to help to understand and determine their suitability for a certain applications (e.g., Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and differential mechanical thermal analysis (DMA)). Weight loss percentage, the degradation temperature, glass transition temperature (Tg), and viscoelastic properties (storage modulus, loss modulus, and the damping factor) are the most common thermal properties determined by these methods. This paper provides an overview of the recent advances made regarding the thermal properties of natural and hybrid fiber composites in thermoset and thermoplastic polymeric matrices. First, the main factors that affect the thermal properties of natural and hybrid fiber composites (fiber and matrix type, the presence of fillers, fiber content and orientation, the treatment of the fibers, and manufacturing process) are briefly presented. Further, the methods used to determine the thermal properties of natural and hybrid composites are discussed. It is concluded that thermal analysis can provide useful information for the development of new materials and the optimization of the selection process of these materials for new applications. It is crucial to ensure that the natural fibers used in the composites can withstand the heat required during the fabrication process and retain their characteristics in service.

RESUMO

A new method to manufacture electrochemical devices based on the graphite and colorless nail polish (N-grap) film was developed for tartrazine (Tz) detection. Scanning Electron Microscopy (SEM) demonstrates that the composite material presents a high porous carbon structure. Cyclic voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS) were employed to electrochemically characterize the electrode material, which corroborates the porous structure of the N-graph due to the enhanced electroactive area (5.4-fold increase) and presented a heterogeneous electron transfer rate constant (k0) of 5.82 × 10-3 cm s-1 for potassium ferricyanide. The electrochemical determination of the Tz was carried out using square-wave voltammetry (SWV), under the optimized experimental conditions, which showed high sensitivity (0.793 A L mol-1) and a lower limit of detection (LOD) of 2.10 × 10-8 mol L-1 with a linear concentration ranging from 2.0 to 50.0 µmol L-1. The developed sensor was applied for the analysis of Tz in sports drink samples and the result obtained by N-grap device was statistically compared with a spectrophotometric method demonstrating good accordance and the accuracy of the proposed method. Based on these results, we believe that this new fabrication method to produce disposable and low-cost electrochemical devices can be an alternative method for in-field analysis of dye in commercial sport drink samples and other relevant applications.

Assuntos

Grafite , Técnicas Eletroquímicas , Eletrodos , Limite de Detecção , Polônia , Tartrazina

RESUMO

This study reports the optical, structural, electrical and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by the solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O⁻H and Zn⁻O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band of gap energy from 5.5 to 5.83 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The electrical properties of the membranes were also characterized by current-voltage characteristics and the DC conductivity showed Arrhenius behavior with values of activation energy from 0.62 to 0.78 eV and maximum conductivity at 2.4 × 10-12 S/cm. The dielectric properties of the nanocomposites were measured from low to high frequencies, and the results showed a high dielectric constant (ε) in the order of 104 at low frequency and values from ε ≈ 2000 to 100 in the range of 1 KHz⁻1 MHz respectively. The properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

RESUMO

Hydroxyapatite-based materials have been used for dental and biomedical applications. They are commonly studied due to their favorable response presented when used for replacement of bone tissue. Those materials should be porous enough to allow cell penetration, internal tissue growth, vascular incursion and nutrient supply. Furthermore, their morphology should be designed to guide the growth of new bone tissue in anatomically applicable ways. In this work, the mechanical performance and 3D X-ray microtomography (X-ray µCT) study of a biomimetic, organic-inorganic composite material, based on hydroxyapatite, with physicochemical, structural, morphological and mechanical properties very similar to those of natural bone tissue is reported. Ceramic pieces in different shapes and several porous sizes were produced using a Modified Gel Casting Method. Pieces with a controlled and 3D hierarchical interconnected porous structure were molded by adding polymethylmethacrylate microspheres. Subsequently, they were subject to a thermal treatment to remove polymers and to promote a sinterization of the ceramic particles, obtaining a HAp scaffold with controlled porosity. Then, two different organic phases were used to generate an organic-inorganic composite material, so gelatin and collagen, which was extracted from bovine tail, were used. The biomimetic organic-inorganic composite material was characterized by Scanning Electron Microscopy, Energy Dispersive X-ray Spectroscopy, X-ray Diffraction, Fourier Transform Infrared Spectroscopy and 3D X-ray microtomography techniques. Mechanical properties were characterized in compression tests, obtaining a dramatic and synergic increment in the mechanical properties due to the chemical and physical interactions between the two phases and to the open-cell cellular behavior of the final composite material; the maximum compressive strength obtained corresponds to about 3 times higher than that reported for natural cancellous bone. The pore size distribution obtained could be capable to allow cell penetration, internal tissue in-growth, vascular incursion and nutrient supply and this material has tremendous potential for use as a replacement of bone tissue or in the manufacture and molding of prosthesis with desired shapes.

Assuntos

Biomimética , Animais , Materiais Biomiméticos , Bovinos , Durapatita , Microscopia Eletrônica de Varredura , Porosidade , Espectroscopia de Infravermelho com Transformada de Fourier , Engenharia Tecidual , Alicerces Teciduais , Difração de Raios X , Microtomografia por Raio-X

RESUMO

Objective: this study aimed to perform a literature review to facilitate the understanding regarding the type of silane used, as well as the processes involved in silanization of filler particles of dental composites. Literature review: the silane agent is essential to promote a bond between organic and inorganic phases of dental composites. The topics addressed in this study are: basic formulation of monomers employed in dental composites, filler particles used, the importance of the bonding agent in material composition, as well as the types of MPTS silane (γ - methacryloxypropyltrimethoxysilane), OTMS (n-octyltrimethoxysilane) UDMS (3-[(1,3(2)-dimethacryloyloxypropyl)- 2 (3)-oxycarbonylamido] propyl triethoxysilane), GPS (γ- glycidoxypropyltrimethoxysilane), and ATES (organosilanes alyltriethoxysilane), the effects of its applications and silanization processes. Final considerations: a detailed analysis of silane agents allows the knowledge of the advantages and disadvantages of these materials to lead to the improvement and subsequent development of other bonding agents that are more suitable for use in the oral cavity.

RESUMO

O objetivo deste trabalho é relatar um caso clínico, demostrando protocolo conservador para reabilitação estética com facetas indiretas de cerâmica associadas ao clareamento dental. Paciente do gênero masculino insatisfeito em relação à estética do seu sorriso apresentou ao exame clínico restaurações em resina composta nos dentes anteriores com pigmentação e fraturas marginais. Foi realizada remoção das restaurações para avaliação dos diastemas. Inicialmente, foi realizado clareamento externo em consultório com peróxido de hidrogênio a 38%. Após uma semana, foram feitos preparos minimamente invasivos na superfície vestibular e moldagem. Os laminados foram confeccionados com cerâmica feldspática e cimentados adesivamente ao substrato dentário. Feita a cimentação, foi feito ajuste oclusal mantendo os contatos oclusais fisiológicos. A associação entre o clareamento dentário e laminados cerâmicos, com preparos conservadores, mostrou-se eficaz para a reabilitação estética e funcional do sorriso contribuindo para a satisfação do paciente.

---

The aim of this study is to describe a clinical case, showing conservative approach for aesthetic rehabilitation with ceramic veneers associated with tooth bleaching. A male patient presented dissatisfaction with smile was submitted to clinical examination and showing composite resin restorations on anterior teeth with marginal fractures and pigmentation. Restoration removal was performed for diastemata evaluation. Initially, was performed in-office tooth bleaching with hydrogen peroxide 38%. After one week, preparations were made with minimally removal of tooth structure at buccal surface and the impression was made. The veneers were fabricated with feldspathic ceramic and cemented adhesively to the tooth substrate. Once the luting procedure was performed, occlusal adjustment was made keeping the physiological occlusal contacts. The association between tooth bleaching and ceramic veneers with conservative approach was effective for the esthetic and functional rehabilitation of the smile contributing to patient satisfaction.