RESUMO

Calcium phosphate (CaP) scaffolds doping with therapeutic ions are one of the focuses of recent bone tissue engineering research. Among the therapeutic ions, strontium stands out for its role in bone remodeling. This work reports a simple method to produce Sr-doped 3D-printed CaP scaffolds, using Sr-doping to induce partial phase transformation from ß-tricalcium phosphate (ß-TCP) to hydroxyapatite (HA), resulting in a doped biphasic calcium phosphate (BCP) scaffold. Strontium carbonate (SrCO3) was incorporated in the formulation of the 3D-printing ink, studying ß-TCP:SrO mass ratios of 100:0, 95:5, and 90:10 (named as ß-TCP, ß-TCP/5-Sr, and ß-TCP/10-Sr, respectively). Adding SrCO3 in the 3D-printing ink led to a slight increase in viscosity but did not affect its printability, resulting in scaffolds with a high printing fidelity compared to the computational design. Interestingly, Sr was incorporated into the lattice structure of the scaffolds, forming hydroxyapatite (HA). No residual SrO or SrCO3 were observed in the XRD patterns of any composition, and HA was the majority phase of the ß-TCP/10-Sr scaffolds. The addition of Sr increased the compression strength of the scaffolds, with both ß-TCP/5-Sr and ß-TCP/10-Sr performing better than the ß-TCP. Overall, ß-TCP/5-Sr presented higher mineralized nodules and mechanical strength, while ß-TCP scaffolds presented superior cell viability. The incorporation of SrCO3 in the ink formulation is a viable method to obtain Sr-BCP scaffolds. Thus, this approach could be explored with other CaP scaffolds aiming to optimize their performance and the addition of alternative therapeutic ions.

RESUMO

Due to bioactive properties, introducing spongin-like collagen (SPG) into the biosilica (BS) extracted from marine sponges would present an enhanced biological material for improving osteoporotic fracture healing by increasing bone formation rate. Our aim was to characterize the morphology of the BS/SPG scaffolds by scanning electron microscopy (SEM), the chemical bonds of the material by Fourier transform infrared spectroscopy (FTIR), and evaluating the orthotopic in vivo response of BS/SPG scaffolds in tibial defects of osteoporotic fractures in rats (histology, histomorphometry, and immunohistochemistry) in two experimental periods (15 and 30 days). SEM showed that scaffolds were porous, showing the spicules of BS and fibrous aspect of SPG. FTIR showed characteristic peaks of BS and SPG. For the in vivo studies, after 30 days, BS and BS/SPG showed a higher amount of newly formed bone compared to the first experimental period, observed both in the periphery and in the central region of the bone defect. For histomorphometry, BS/SPG presented higher %BV/TV compared to the other experimental groups. After 15 days, BS presented higher volumes of collagen type I. After 30 days, all groups demonstrated higher volumes of collagen type III compared to volumes at 15 days. After 30 days, BS/SPG presented higher immunostaining of osteoprotegerin compared to the other experimental groups at the same experimental period. The results showed that BS and BS/SPG scaffolds were able to improve bone healing. Future research should focus on the effects of BS/SPG on longer periods in vivo studies.

Assuntos

Colágeno , Poríferos , Alicerces Teciduais , Animais , Ratos , Alicerces Teciduais/química , Poríferos/química , Colágeno/metabolismo , Feminino , Dióxido de Silício/química , Osteoporose/patologia , Ratos Wistar , Fraturas por Osteoporose , Microscopia Eletrônica de Varredura , Osteogênese/efeitos dos fármacos , Espectroscopia de Infravermelho com Transformada de Fourier , Tíbia

RESUMO

BACKGROUND: Tissue engineering represents a promising field in regenerative medicine, with bioresorbable polymers such as polycaprolactone (PCL) playing a crucial role as scaffolds. These scaffolds support the growth and repair of tissues by mimicking the extracellular matrix. OBJECTIVE: This study aimed to assess the in vivo performance of three-dimensional PCL scaffolds by evaluating their effects on bone repair in rat calvaria and the tissue reaction in subcutaneous implant sites, as well as their impact on major organs such as the kidneys, lungs, and liver. METHODS: Three-dimensional scaffolds made of PCL were implanted in the subcutaneous tissue of rats' backs and calvaria. Histological analyses were conducted to observe the bone repair process in calvaria and the tissue response in subcutaneous implant sites. Additionally, the kidneys, lungs, and livers of the animals were examined for any adverse tissue alterations. RESULTS: The histological analysis of the bone repair in calvaria revealed newly formed bone growing towards the center of the defects. In subcutaneous tissues, a thin fibrous capsule with collagenous fibers enveloping the implant was observed in all animals, indicating a positive tissue response. Importantly, no harmful alterations or signs of inflammation, hyperplasia, metaplasia, dysplasia, or hemorrhage were detected in the kidneys, lungs, and liver. CONCLUSIONS: The findings demonstrate that PCL scaffolds produced through additive manufacturing are biocompatible, non-cytotoxic, and bioresorbable, promoting osteoconduction without adverse effects on major organs. Hence, PCL is confirmed as a suitable biomaterial for further studies in tissue engineering and regenerative medicine.

RESUMO

Bone tissue engineering is a promising alternative to repair wounds caused by cellular or physical accidents that humans face daily. In this sense, the search for new graphene oxide (GO) nanofillers related to their degree of oxidation is born as an alternative bioactive component in forming new scaffolds. In the present study, three different GOs were synthesized with varying degrees of oxidation and studied chemically and tissue-wise. The oxidation degree was determined through infrared (FTIR), X-ray diffraction (XRD), X-ray photoelectron (XPS), and Raman spectroscopy (RS). The morphology of the samples was analyzed using scanning electron microscopy (SEM). The oxygen content was deeply described using the deconvolution of RS and XPS techniques. The latter represents the oxidation degree for each of the samples and the formation of new bonds promoted by the graphitization of the material. In the RS, two characteristic bands were observed according to the degree of oxidation and the degree of graphitization of the material represented in bands D and G with different relative intensities, suggesting that the samples have different crystallite sizes. This size was described using the Tuinstra-Koenig model, ranging between 18.7 and 25.1 nm. Finally, the bone neoformation observed in the cranial defects of critical size indicates that the F1 and F2 samples, besides being compatible and resorbable, acted as a bridge for bone healing through regeneration. This promoted healing by restoring bone and tissue structure without triggering a strong immune response.

Assuntos

Regeneração Óssea , Grafite , Engenharia Tecidual , Alicerces Teciduais , Grafite/química , Regeneração Óssea/efeitos dos fármacos , Engenharia Tecidual/métodos , Animais , Alicerces Teciduais/química , Nanoestruturas/química , Osso e Ossos/efeitos dos fármacos , Análise Espectral Raman , Oxirredução , Difração de Raios X , Materiais Biocompatíveis/química , Materiais Biocompatíveis/farmacologia , Ratos , Espectroscopia de Infravermelho com Transformada de Fourier

RESUMO

Bioactive and biodegradable scaffolds that mimic the natural extracellular matrix of bone serve as temporary structures to guide new bone tissue growth. In this study, 3D-printed scaffolds composed of poly (lactic acid) (PLA)-tricalcium phosphate (TCP) (90-10 wt.%) were modified with 1%, 5%, and 10 wt.% of ZnO to enhance bone tissue regeneration. A commercial chain extender named Joncryl was incorporated alongside ZnO to ensure the printability of the composites. Filaments were manufactured using a twin-screw extruder and subsequently used to print 3D scaffolds via fused filament fabrication (FFF). The scaffolds exhibited a homogeneous distribution of ZnO and TCP particles, a reproducible structure with 300 µm pores, and mechanical properties suitable for bone tissue engineering, with an elastic modulus around 100 MPa. The addition of ZnO resulted in enhanced surface roughness on the scaffolds, particularly for ZnO microparticles, achieving values up to 241 nm. This rougher topography was responsible for enhancing protein adsorption on the scaffolds, with an increase of up to 85% compared to the PLA-TCP matrix. Biological analyses demonstrated that the presence of ZnO promotes mesenchymal stem cell (MSC) proliferation and differentiation into osteoblasts. Alkaline phosphatase (ALP) activity, an important indicator of early osteogenic differentiation, increased up to 29%. The PLA-TCP composite containing 5% ZnO microparticles exhibited an optimized degradation rate and enhanced bioactivity, indicating its promising potential for bone repair applications.

Assuntos

Materiais Biocompatíveis , Regeneração Óssea , Fosfatos de Cálcio , Diferenciação Celular , Proliferação de Células , Células-Tronco Mesenquimais , Osteoblastos , Poliésteres , Impressão Tridimensional , Engenharia Tecidual , Alicerces Teciduais , Óxido de Zinco , Alicerces Teciduais/química , Fosfatos de Cálcio/química , Poliésteres/química , Regeneração Óssea/efeitos dos fármacos , Engenharia Tecidual/métodos , Células-Tronco Mesenquimais/citologia , Óxido de Zinco/química , Materiais Biocompatíveis/química , Diferenciação Celular/efeitos dos fármacos , Osteoblastos/citologia , Osteogênese/efeitos dos fármacos , Teste de Materiais , Osso e Ossos , Regeneração Tecidual Guiada/métodos , Humanos , Animais , Fosfatase Alcalina/metabolismo , Módulo de Elasticidade , Porosidade , Propriedades de Superfície

RESUMO

Hybrid scaffolds that are based on PLA and PLA/PMMA with 75/25, 50/50, and 25/75 weight ratios and functionalized with 10 wt.% of bioglass nanoparticles (n-BG) were developed using an electrospinning technique with a chloroform/dimethylformamide mixture in a 9:1 ratio for bone tissue engineering applications. Neat PLA and PLA/PMMA hybrid scaffolds were developed successfully through a (CF/DMF) solvent system, obtaining a random fiber deposition that generated a porous structure with pore interconnectivity. However, with the solvent system used, it was not possible to generate fibers in the case of the neat PMMA sample. With the increase in the amount of PMMA in PLA/PMMA ratios, the fiber diameter of hybrid scaffolds decreases, and the defects (beads) in the fiber structure increase; these beads are associated with a nanoparticle agglomeration, that could be related to a low interaction between n-BG and the polymer matrix. The Young's modulus of PLA/PMMA/n-BG decreases by 34 and 80%, indicating more flexible behavior compared to neat PLA. The PLA/PMMA/n-BG scaffolds showed a bioactive property related to the presence of hydroxyapatite crystals in the fiber surface after 28 days of immersion in a Simulated Body Fluids solution (SBF). In addition, the hydrolytic degradation process of PLA/PMMA/n-BG, analyzed after 35 days of immersion in a phosphate-buffered saline solution (PBS), was less than that of the pure PLA. The in vitro analysis using an HBOF-1.19 cell line indicated that the PLA/PMMA/n-BG scaffold showed good cell viability and was able to promote cell proliferation after 7 days. On the other hand, the in vivo biocompatibility evaluated via a subdermal model in BALC male mice corroborated the good behavior of the scaffolds in avoiding the generation of a cytotoxic effect and being able to enhance the healing process, suggesting that the materials are suitable for potential applications in tissue engineering.

Assuntos

Cerâmica , Nanopartículas , Poliésteres , Polimetil Metacrilato , Engenharia Tecidual , Alicerces Teciduais , Engenharia Tecidual/métodos , Poliésteres/química , Polimetil Metacrilato/química , Alicerces Teciduais/química , Cerâmica/química , Cerâmica/farmacologia , Nanopartículas/química , Animais , Camundongos , Osso e Ossos/efeitos dos fármacos , Materiais Biocompatíveis/química , Materiais Biocompatíveis/farmacologia , Humanos , Linhagem Celular

RESUMO

Context: The development of porous devices using materials modified with various natural agents has become a priority for bone healing processes in the oral and maxillofacial field. There must be a balance between the proliferation of eukaryotic and the inhibition of prokaryotic cells to achieve proper bone health. Infections might inhibit the formation of new alveolar bone during bone graft augmentation. Objective: This study aimed to evaluate the in vitro osteogenic behavior of human bone marrow stem cells and assess the antimicrobial response to 3D-printed porous scaffolds using propolis-modified wollastonite. Methodology: A fractional factorial design of experiments was used to obtain a 3D printing paste for developing scaffolds with a triply periodic minimal surface (TPMS) gyroid geometry based on wollastonite and modified with an ethanolic propolis extract. The antioxidant activity of the extracts was characterized using free radical scavenging methods (DPPH and ABTS). Cell proliferation and osteogenic potential using Human Bone Marrow Stem Cells (bmMSCs) were assessed at different culture time points up to 28 days. MIC and inhibition zones were studied from single strain cultures, and biofilm formation was evaluated on the scaffolds under co-culture conditions. The mechanical strength of the scaffolds was evaluated. Results: Through statistical design of experiments, a paste suitable for printing scaffolds with the desired geometry was obtained. Propolis extracts modifying the TPMS gyroid scaffolds showed favorable cell proliferation and metabolic activity with osteogenic potential after 21 days. Additionally, propolis exhibited antioxidant activity, which may be related to the antimicrobial effectiveness of the scaffolds against S. aureus and S. epidermidis cultures. The mechanical properties of the scaffolds were not affected by propolis impregnation. Conclusion: These results demonstrate that propolis-impregnated porous wollastonite scaffolds might have the potential to stimulate bone repair in maxillofacial tissue engineering applications.

RESUMO

The fabrication of customized implants by additive manufacturing has allowed continued development of the personalized medicine field. Herein, a 3D-printed bioabsorbable poly (lactic acid) (PLA)- ß-tricalcium phosphate (TCP) (10 wt %) composite has been modified with CeO2 nanoparticles (CeNPs) (1, 5 and 10 wt %) for bone repair. The filaments were prepared by melt extrusion and used to print porous scaffolds. The nanocomposite scaffolds possessed precise structure with fine print resolution, a homogenous distribution of TCP and CeNP components, and mechanical properties appropriate for bone tissue engineering applications. Cell proliferation assays using osteoblast cultures confirmed the cytocompatibility of the composites. In addition, the presence of CeNPs enhanced the proliferation and differentiation of mesenchymal stem cells; thereby, increasing alkaline phosphatase (ALP) activity, calcium deposition and bone-related gene expression. Results from this study have shown that the 3D printed PLA-TCP-10%CeO2 composite scaffold could be used as an alternative polymeric implant for bone tissue engineering applications: avoiding additional/revision surgeries and accelerating the regenerative process.

RESUMO

The growing demand for more efficient materials for medical applications brought together two previously distinct fields: medicine and engineering. Regenerative medicine has evolved with the engineering contributions to improve materials and devices for medical use. In this regard, graphene is one of the most promising materials for bone tissue engineering and its potential for bone repair has been studied by several research groups. The aim of this study is to conduct a scoping review including articles published in the last 12 years (from 2010 to 2022) that have used graphene and its derivatives (graphene oxide and reduced graphene) in preclinical studies for bone tissue regeneration, searching in PubMed/MEDLINE, Embase, Web of Science, Cochrane Central, and clinicaltrials.gov (to confirm no study has started with clinical trial). Boolean searches were performed using the defined key words "bone" and "graphene", and manuscript abstracts were uploaded to Rayyan, a web-tool for systematic and scoping reviews. This scoping review was conducted based on Joanna Briggs Institute Manual for Scoping Reviews and the report follows the recommendations of the Preferred Reporting Items for Systematic Reviews and Meta-Analyses - Extension for Scoping Reviews (PRISMA-ScR) statement. After the search protocol and application of the inclusion criteria, 77 studies were selected and evaluated by five blinded researchers. Most of the selected studies used composite materials associated with graphene and its derivatives to natural and synthetic polymers, bioglass, and others. Although a variety of graphene materials were analyzed in these studies, they all concluded that graphene, its derivatives, and its composites improve bone repair processes by increasing osteoconductivity, osteoinductivity, new bone formation, and angiogenesis. Thus, this systematic review opens up new opportunities for the development of novel strategies for bone tissue engineering with graphene.

Assuntos

Materiais Biocompatíveis , Engenharia Tecidual , Osso e Ossos , Medicina Regenerativa , Regeneração Óssea

RESUMO

Bone defects lead to the structural loss of normal architecture, and those in the field of bone tissue engineering are searching for new alternatives to aid bone regeneration. Dental pulp-mesenchymal stem cells (DP-MSC) could provide a promising alternative to repair bone defects, principally due to their multipotency and capacity to fabricate three-dimensional (3D) spheroids. The present study aimed to characterize the 3D DP-MSC microsphere and the osteogenic differentiation capacity potential cultured by a magnetic levitation system. To achieve this, the 3D DP-MSC microsphere was grown for 7, 14, and 21 days in an osteoinductive medium and compared to 3D human fetal osteoblast (hFOB) microspheres by examining the morphology, proliferation, osteogenesis, and colonization onto PLA fiber spun membrane. Our results showed good cell viability for both 3D microspheres with an average diameter of 350 µm. The osteogenesis examination of the 3D DP-MSC microsphere revealed the lineage commitment, such as the hFOB microsphere, as evidenced by ALP activity, the calcium content, and the expression of osteoblastic markers. Finally, the evaluation of the surface colonization exhibited similar patterns of cell-spreading over the fibrillar membrane. Our study demonstrated the feasibility of forming a 3D DP-MSC microsphere structure and the cell-behavior response as a strategy for the applications of bone tissue guiding.

RESUMO

Nanofiber scaffolds of polyvinyl alcohol, silk fibroin from Bombyx mori cocoons, and silver nanoparticles were developed as a substrate for MG-63 growth. The fiber morphology, mechanical properties, thermal degradation, chemical composition, and water contact angle were investigated. In vitro tests were performed by the cell viability MTS test of MG-63 cells on electrospun PVA scaffolds, mineralization was analyzed by alizarin red, and the alkaline phosphatase (ALP) assay was evaluated. At higher PVA concentrations, Young's modulus (E) increased. The addition of fibroin and silver nanoparticles improved the thermal stability of PVA scaffolds. FTIR spectra indicated characteristic absorption peaks related to the chemical structures of PVA, fibroin, and Ag-NPs, demonstrating good interactions between them. The contact angle of the PVA scaffolds decreased with the incorporation of fibroin and showed hydrophilic characteristics. In all concentrations, MG-63 cells on PVA/fibroin/Ag-NPs scaffolds had higher cell viability than PVA pristine. On day ten of culture, PVA18/SF/Ag-NPs showed the highest mineralization, observed by the alizarin red test. PVA10/SF/Ag-NPs presented the highest alkaline phosphatase activity after an incubation time of 37 h. The achievements indicate the potential of the nanofibers of PVA18/SF/Ag-NPs as a possible substitute for bone tissue engineering (BTE).

RESUMO

A highly porous structure, and an inorganic (biosilica) and collagen-like organic content (spongin) makes marine sponges potential candidates to be used as natural scaffolds in bone tissue engineering. The aim of this study was to characterize (through SEM, FTIR, EDS, XRD, pH, mass degradation and porosity tests) scaffolds produced from two species of marine sponges, Dragmacidon reticulatum (DR) and Amphimedon viridis (AV), and to evaluate the osteogenic potential of these scaffolds by using a bone defect model in rats. First, it was shown that the same chemical composition and porosity (84 ± 5% for DR and 90 ± 2% for AV) occurs among scaffolds from the two species. Higher material degradation was observed in the scaffolds of the DR group, with a greater loss of organic matter after incubation. Later, scaffolds from both species were surgically introduced in rat tibial defects, and histopathological analysis after 15 days showed the presence of neo-formed bone and osteoid tissue within the bone defect in DR, always around the silica spicules. In turn, AV exhibited a fibrous capsule around the lesion (19.9 ± 17.1%), no formation of bone tissue and only a small amount of osteoid tissue. The results showed that scaffolds manufactured from Dragmacidon reticulatum presented a more suitable structure for stimulation of osteoid tissue formation when compared to Amphimedon viridis marine sponge species.

RESUMO

Bone lesions affect individuals of different age groups, compromising their daily activities and potentially leading to prolonged morbidity. Over the years, new compositions and manufacturing technologies were developed to offer customized solutions to replace injured tissue and stimulate tissue regeneration. This work used digital light processing (DPL) technology for three-dimensional (3D) printing of porous structures using pre-ceramic polymer, followed by pyrolysis to obtain SiOC vitreous scaffolds. The SiOC scaffolds produced had an amorphous structure (compatible with glass) with an average porosity of 72.69% ± 0.99, an average hardness of 935.1 ± 71.0 HV, and an average maximum flexural stress of 7.8 ± 1.0 MPa, similar to cancellous bone tissue. The scaffolds were not cytotoxic and allowed adult stem cell adhesion, growth, and expansion. After treatment with osteoinductive medium, adult stem cells in the SiOC scaffolds differentiated to osteoblasts, assuming a tissue-like structure, with organization in multiple layers and production of a dense fibrous matrix rich in hydroxyapatite. The in vitro analyses supported the hypothesis that the SiOC scaffolds produced in this work were suitable for use as a bone substitute for treating critically sized lesions, with the potential to stimulate the gradual process of regeneration of the native tissue. The data obtained stimulate the continuity of studies with the SiOC scaffolds developed in this work, paving the way for evaluating safety and biological activity in vivo.

RESUMO

Gelatin methacryloyl (GelMA)-based composites are evolving three-dimensional (3D) networking hydrophilic protein composite scaffolds with high water content. These protein composites have been devoted to biomedical applications due to their unique abilities, such as flexibility, soft structure, versatility, stimuli-responsiveness, biocompatibility, biodegradability, and others. They resemble the native extracellular matrix (ECM) thanks to their remarkable cell-adhesion and matrix-metalloproteinase (MMP)-responsive amino acid motifs. These favorable properties promote cells to proliferate and inflate within GelMA-protein scaffolds. The performance of GelMA composites has been enriched using cell-amenable components, including peptides and proteins with a high affinity to harmonize cellular activities and tissue morphologies. Due to their inimitable merits, GelMA systems have been used in various fields such as drug delivery, biosensor, the food industry, biomedical, and other health sectors. The current knowledge and the role of GelMA scaffolds in bone tissue engineering are limited. The rational design and development of novel nanomaterials-incorporated GelMA-based composites with unique physicochemical and biological advantages would be used to regulate cellular functionality and bone regeneration. Substantial challenges remain. This review focuses on recent progress in mitigating those disputes. The study opens with a brief introduction to bone tissue engineering and GelMA-based composites, followed by their potential applications in bone tissue engineering. The future perspectives and current challenges of GelMA composites are demonstrated. This review would guide the researchers to design and fabricate more efficient multifunctional GelMA-based composites with improved characteristics for their practical applications in bone tissue engineering and biomedical segments.

RESUMO

Bone defects have prompted the development of biomaterial-based bone substitutes for restoring the affected tissue completely. Although many biomaterials have been designed and evaluated, the combination of properties required in a biomaterial for bone tissue engineering still poses a challenge. In this study, a chitosan-silica-based biocomposite was synthetized, and its physicochemical characteristics and biocompatibility were characterized, with the aim of exploring the advantages and drawbacks of its use in bone tissue engineering. Dynamic light scattering measurements showed that the mean hydrodynamic size of solid silica particles (Sol-Si) was 482 ± 3 nm. Scanning electron microscopy of the biocomposite showed that Sol-Si were homogenously distributed within the chitosan (CS) matrix. The biocomposite swelled rapidly and was observed to have no cytotoxic effect on the [3T3] cell line within 24 h. Biocompatibility was also analyzed in vivo 14 days post-implant using a murine experimental model (Wistar rats). The biocomposite was implanted in the medullary compartment of both tibiae (n = 12). Histologically, no acute inflammatory infiltrate or multinucleated giant cells associated to the biocomposite were observed, indicating good biocompatibility. At the tissue-biocomposite interface, there was new formation of woven bone tissue in close contact with the biocomposite surface (osseointegration). The new bone formation may be attributed to the action of silica. Free silica particles originating from the biocomposite were observed at the tissue-biocomposite interface. According to our results, the biocomposite may act as a template for cellular interactions and extracellular matrix formation, providing a structural support for new bone tissue formation. The CS/Sol-Si biocomposite may act as a Si reservoir, promoting new bone formation. A scaffold with these properties is essential for cell differentiation and filling a bone defect.

Assuntos

Substitutos Ósseos , Quitosana , Ratos , Camundongos , Animais , Substitutos Ósseos/química , Engenharia Tecidual , Quitosana/química , Dióxido de Silício/química , Ratos Wistar , Materiais Biocompatíveis/farmacologia , Materiais Biocompatíveis/química , Alicerces Teciduais/química

RESUMO

A engenharia de tecidos ósseos é um ramo importante da medicina regenerativa e envolve o desenvolvimento de arcabouços com composição e arquitetura favoráveis à integração celular, além do estudo de fatores capazes de promover a adesão e proliferação celular, incluindo estímulos químicos e biofísicos. O objetivo do estudo foi avaliar a utilização do laser de baixa intensidade (LBI) como uma ferramenta para promover a bioestimulação in vitro de células osteoblásticas cultivadas em arcabouços nanofibrosos de ácido polilático (PLA). Os arcabouços foram produzidos pela técnica de eletrofiação e caracterizados quanto à molhabilidade, composição pela espectroscopia no infravermelho por transformada de Fourier (FTIR), morfologia da superfície por microscópica eletrônica de varredura (MEV), caracterização termogravimétrica (TGA), calorimetria diferencial exploratória (DSC) e cristalinidade por difração de raios-X (DRX). Os ensaios biológicos foram conduzidos com osteoblastos da linhagem OFCOL II cultivados na superfície dos arcabouços e submetidos ou não (grupo controle) a irradiação com laser diodo InGaAIP na potência de 30 mW, nas doses de 1, 4 e 6 J/cm² e nos comprimentos de onda de 660 nm (grupos V1, V4, V6, respectivo as doses) e 780 nm (grupos I1, I4 e I6, respectivo as doses). Os efeitos do LBI na proliferação dos osteoblastos foram avaliados através do método bioquímico Alamar Blue, nos intervalos de 24, 48 e 72h, enquanto a viabilidade e a morfologia celular foram analisadas no intervalo de 72h, através do ensaio Live/Dead e da microscopia eletrônica de varredura (MEV), respectivamente. Os dados do ensaio bioquímico de Alamar Blue mostraram uma maior proliferação celular nos grupos V6 em todos os intervalos analíticos em comparação ao grupo controle (p<0,05). Outras diferenças entre o grupo controle e irradiados foram encontradas apenas nos intervalos de 48h e 72h para V1, e para o grupo IV6 em 72h. O ensaio Live/Dead revelou um aumento na viabilidade celular nos grupos trados com LBI, sendo significativamente maior no grupo V1 quando comparado ao grupo controle. A análise por MEV mostrou adequada interação dos osteoblastos aos arcabouços, com o corpo celular se espalhando ao longo do eixo da nanofibra e a presença de contatos físicos mais evidentes, através da formação de ligação por meio de filopódios e lamelipódios, nos grupos V1, V6 e I6. Em conjunto, os dados do presente trabalho mostraram que o LBI promove a bioestimulação de osteoblastos cultivados sobre nanofibras de PLA, o que aponta para o seu uso potencial nas técnicas de engenharia tecidual óssea, sobretudo no que se refere ao uso do comprimento de onda de 660 nm, a qual apresentou grupos com mais resultados significativos (AU).

---

Bone tissue engineering is a relevant branch of regenerative medicine and involves the development of scaffolds with composition and architecture favorable to cell integration, in addition to studying factors capable of promoting cell adhesion and proliferation, including chemical and biophysical stimuli. The study aimed to evaluate the use of low-level laser irradiation (LLLI) to promote in vitro biostimulation of osteoblastic cells cultured on polylactic acid (PLA) nanofibrous scaffolds. The scaffolds were produced by the electrospinning technique and characterized in terms of wettability, composition by Fourier transform infrared spectroscopy (FTIR), surface morphology by scanning electron microscopy (SEM), thermogravimetric characterization (TGA), differential scanning calorimetry (DSC) and crystallinity by Xray diffraction (XRD). The biological assays were conducted with osteoblasts of the OFCOL II lineage cultured on the surface of the scaffolds and submitted or not (control group) to irradiation with InGaAIP diode laser, power of 30 mW, with doses of 1, 4 and 6 J/cm² and wavelengths of 660 nm (groups V1, V4, V6, respectively doses) and 780 nm (groups I1, I4 and I6, respectively doses). The effects of LLLT from the perspective of osteoblasts were evaluated using the biochemical method Alamar Blue assay, at intervals of 24, 48 and 72h, while cell viability and morphology were observed at 72h, using the Live/Dead assay and electron microscopy. scan (SEM), respectively. The Alamar Blue assay data showed more significant cell proliferation in groups in the V6 groups at all analytical intervals compared to the control group (p<0.05). Other differences between the control and irradiated groups were found only at intervals of 48h and 72h for V1, and for group IV6 at 72h. The Live/Dead assay revealed an increase in cell viability in the groups treated with LLLT, being significantly higher in the V1 group when compared to the control group. SEM analysis showed adequate interaction between osteoblasts and scaffolds, with the cell body spreading along the nanofiber axis and the presence of more evident physical contacts, through the formation of bonds through filopodia and lamellipodia, in groups V1, V6 and I6. Together, the data from the present study observed that LLLT promotes the biostimulation of osteoblasts cultured on PLA nanofibers, which pointed to its potential use in bone tissue engineering techniques, especially with regard to the use of the wavelength of 660 nm, which presented groups with more significant results (AU).

Assuntos

Osteoblastos , Regeneração Óssea , Terapia com Luz de Baixa Intensidade/instrumentação , Engenharia Tecidual , Técnicas In Vitro/métodos , Varredura Diferencial de Calorimetria/instrumentação , Microscopia Eletrônica de Varredura/instrumentação , Espectroscopia de Infravermelho com Transformada de Fourier/instrumentação

RESUMO

Abstract Recently, the 3D spheroid cell culture application has been extensively used in the treatment of bone defects. A wide variety of methodologies have been used, which has made the comparison of results complex. Therefore, this systematic review has two aims: (i) to perform an analysis focused on the role of 3D spheroid cell culture in bone regeneration strategies; and (ii) address the main challenges in clinical application. A search of the following keywords "3D cell culture", "spheroid", and "bone regeneration" was carried out in the PubMed, Scopus, and ScienceDirect databases and limited to the years 2010-2020. Studies were included if their primary objective was the behavior of cell aggregates to formed spheroids structures by different 3D cell culture techniques focused on the regeneration of bone tissue. To address the risk of bias for in vitro studies, the United States national toxicology program tool was applied, and descriptive statistics of the data were performed, with the SPSS V.22 program. A total of 16 studies were included, which met the established criteria corresponding to in vitro and in vitro/in vivo studies; most of these studies used stem cells for the 3D cell spheroids. The most often methods used for the 3D formation were low adherence surface and rotational methods, moreover, mesenchymal stem cells were the cell line most frequently used because of their regenerative potential in the field of bone tissue engineering. Although the advances in research on the potential use of 3D spheroids in bone regeneration have made great strides, the constant innovation in cell spheroid formation methodologies means that clinical application remains in the future as strategy for 3D tissue bioprinting.

---

Resumen Recientemente, la aplicación del cultivo 3D de esferoides se ha utilizado ampliamente en el tratamiento de defectos óseos. La variedad de metodologías para lograr los cultivos 3D de esferoides ha hecho compleja la comparación de resultados. Por tanto, esta revisión sistemática tiene dos objetivos: (i) realizar un análisis centrado en el papel de los cultivos 3D de esferoides en las estrategias de regeneración ósea; y (ii) abordar los principales desafíos en la aplicación clínica. Se realizó una búsqueda de las siguientes palabras clave "cultivo celular 3D", "esferoide" y "regeneración ósea" en las bases de datos PubMed, Scopus y ScienceDirect y se limitó a los años 2010-2020. Se incluyeron los estudios si su principal objetivo era el comportamiento de agregados celulares para generar las estructuras esferoidales desarrollados por diferentes técnicas de cultivo celular 3D enfocadas a la regeneración del tejido óseo. Para abordar el riesgo de sesgo de los estudios in vitro, se aplicó la herramienta del programa nacional de toxicología de Estados Unidos y se realizaron estadísticas descriptivas de los datos, con el programa SPSS V.22. Se incluyeron un total de 16 estudios, que cumplieron con los criterios establecidos correspondientes a estudios in vitro e in vitro/in vivo; la mayoría de estos estudios utilizaron células troncales para generar los esferoides celulares 3D. Los métodos más utilizados para la formación de los esferoides 3D fueron la superficie de baja adherencia y los métodos de rotación, asimismo, la línea celular de células troncales mesenquimales fueron las más utilizadas debido a su gran potencial regenerativo en el campo de la ingeniería de tejidos óseos. Aunque los avances en la investigación sobre el uso potencial de los cultivos celulares de esferoides 3D en la regeneración ósea han logrado grandes avances, la constante innovación en las metodologías de la generación de esferoides 3D deja claro que la aplicación clínica de estos permanecerá en el futuro como estrategia en la bioimpresión tisular.

Assuntos

Regeneração Óssea , Engenharia Tecidual , Esferoides Celulares

RESUMO

Bone is a hierarchical material that has inspired the design of biopolymer-derived biocomposites for tissue engineering purposes. The present study sought to synthesize and perform the physicochemical characterization and biocompatibility of a collagen-silica-based biocomposite for potential application in bone tissue engineering. Ultrastructure, biodegradability, swelling behavior, and biocompatibility properties were analyzed to gain insight into the advantages and limitations to the use of this biomaterial as a bone substitute. Scanning electron microscopy analysis showed a packed-collagen fibril matrix and silica particles in the biocomposite three-dimensional structure. As shown by analysis of in vitro swelling behavior and biodegradability, it would seem that the material swelled soon after implantation and then suffered degradation. Biocompatibility properties were analyzed in vivo 14-days postimplantation using an experimental model in Wistar rats. The biocomposite was placed inside the hematopoietic bone marrow compartment of both tibiae (n = 16). Newly formed woven bone was observed in response to both materials. Unlike the pure-collagen-tissue interface, extensive areas of osseointegration were observed at the biocomposite-tissue interface, which would indicate that silica particles stimulated new bone formation. Agglomerates of finely particulate material with no inflammatory infiltrate or multinucleated giant cells were observed in the bone marrow implanted with the biocomposite. The biocomposite showed good biocompatibility properties. Further studies are necessary to evaluate their biological behavior over time.

Assuntos

Dióxido de Silício , Engenharia Tecidual , Animais , Materiais Biocompatíveis/química , Materiais Biocompatíveis/farmacologia , Osso e Ossos , Colágeno , Ratos , Ratos Wistar , Engenharia Tecidual/métodos

RESUMO

Although many bone substitutes have been designed and produced, the development of bone tissue engineering products that mimic the microstructural characteristics of native bone remains challenging. It has been shown that pore orientation within collagen scaffolds influences bone matrix formation by the endochondral route. In addition, that the unidirectional orientation of the scaffolds can limit the growth of blood vessels. However, a comparison between the amount of bone that can be formed in scaffolds with different pore orientations in addition to analyzing the effect of loading osteogenic and proangiogenic factors is still required. In this work we fabricated uni- and multidirectional collagen sponges and evaluated their microstructural, physicochemical, mechanical and biological characteristics. Although the porosity and average pore size of the uni- and multidirectional scaffolds was similar (94.5% vs. 97.1% and 260 µm vs. 269 µm, respectively) the unidirectional sponges had a higher tensile strength, Young's modulus and capacity to uptake liquids than the multidirectional ones (0.271 MPa vs. 0.478 MPa, 9.623 MPa vs. 3.426 MPa and 8000% mass gain vs. 4000%, respectively). Culturing of rat bone marrow mesenchymal stem cells demonstrated that these scaffolds support cell growth and osteoblastic differentiation in the presence of BMP-2 in vitro, although the pore orientation somehow affected cell attachment and differentiation. The evaluation of the ability of the scaffolds to support bone growth when loaded with BMP-2 or BMP-2 + VEGF in an ectopic rat model showed that they both supported bone formation. Histological analysis and quantification of mineralized matrix revealed that the pore orientation of the collagen scaffolds influenced the osteogenic process.

RESUMO

The occurrence of bone-related disorders and diseases has dramatically increased in recent years around the world. Demineralized bone matrix (DBM) has been widely used as a bone implant due to its osteoinduction and bioactivity. However, the use of DBM is limited because it is a particulate material, which makes it difficult to manipulate and implant with precision. In addition, these particles are susceptible to migration to other sites. To address this situation, DBM is commonly incorporated into a variety of carriers. An injectable scaffold has advantages over bone grafts or preformed scaffolds, such as the ability to flow and fill a bone defect. The aim of this research was to develop a DBM carrier with such viscoelastic properties in order to obtain an injectable bone substitute (IBS). The developed DBM carrier consisted of a PVA/glycerol network cross-linked with borax and reinforced with CaCO3 as a pH neutralizer, porosity generator, and source of Ca. The physicochemical properties were determined by an injectability test, FTIR, SEM, and TGA. Porosity, degradation, bioactivity, possible cytotoxic effect, and proliferation in osteoblasts were also determined. The results showed that the developed material has great potential to be used in bone tissue regeneration.