RESUMO
The aim of this study was to compare the physicochemical, rheological, and morphological characteristics of corn, nixtamalized flour, masa, and tortillas from the traditional nixtamalization process (TNP) and the extrusion nixtamalization process (ENP) and their relationship with starch. The traditional and extrusion processes were carried out using the same variety of corn. From both processes, samples of ground corn, nixtamalized flour, masa, and tortillas were obtained. The extrusion process produced corn flour with particle sizes smaller (particle size index, PSI = 51) than that of flour produced by the traditional nixtamalization process (PSI = 44). Masa from the TNP showed higher modulus of elasticity (G') and viscosity (G â³) values than that off masa from the ENP. Furthermore, in a temperature sweep test, masa from the TNP showed a peak in G' and G â³, while the masa from the ENP did not display these peaks. The ENP-produced tortillas had higher resistant starch contents and comparable firmness and rollability to those from the TNP but lower quality parameter values. A comparison of the products' physicochemical properties obtained by the two processes shows the importance of controlling the damage to starch during the milling and extrusion processes to obtain tortillas of better quality. For the first time, we propose the measurement of the viscoelastic parameters G' and G â³ in temperature sweep mode to monitor changes in the degree of starch damage.
RESUMO
Sorghum is a cereal with little use in human diet; however, this grain can provide several nutrients and, additionally, has a high content of phenolic compounds concentrated in bran, which could be beneficial to human health due to its high antioxidant capacity. However, these bioactive compounds are bound within the cell wall matrix; it is necessary to release these compounds to take advantage of their antioxidant properties. The extrusion process increases the accessibility of bound phenolic compounds, breaking their bonds from the bran matrix. The aim of this study was to determine the optimal extrusion conditions for maximizing the phenolic compound content and antioxidant capacity of sorghum bran extrudate. The extrusion process factors evaluated were feed moisture (FM) from 25 to 35% and the fourth extrusion zone temperature (T) in the range of 140-180 °C. Analysis of variance and response surface analysis were used in the evaluation. The prediction coefficient, (FM)2, (T)2 and their interaction (FM)(T) significantly affected the free total phenolic compounds. The antioxidant capacity of the free total phenolic compounds was significantly affected by (FM)2 and (T)2. The optimal extrusion conditions were FM = 30% and T = 160 °C, which provided free total phenolic compounds with a value of 7428.95 µg GAE/g (predicted value: 7810.90 µg GAE/g) and antioxidant capacity with a value of 14.12 µmol TE/g (predicted value: 14.85 µmol TE/g). Results confirmed that extrusion process optimization was useful to increase the content of phenolic compounds and improved the antioxidant capacity of sorghum bran.
Assuntos
Sorghum , Antioxidantes , Dieta , Grão Comestível , Humanos , FenóisRESUMO
Extrusion is an alternative technology for the production of nixtamalized products. The aim of this study was to obtain an expanded nixtamalized snack with whole blue corn and using the extrusion process, to preserve the highest possible total anthocyanin content, intense blue/purple coloration (color b) and the highest expansion index. A central composite experimental design was used. The extrusion process factors were: feed moisture (FM, 15%-23%), calcium hydroxide concentration (CHC, 0%-0.25%) and final extruder temperature (T, 110-150 °C). The chemical and physical properties evaluated in the extrudates were moisture content (MC, %), total anthocyanins (TA, mg·kg(-1)), pH, color (L, a, b) and expansion index (EI). ANOVA and surface response methodology were applied to evaluate the effects of the extrusion factors. FM and T significantly affected the response variables. An optimization step was performed by overlaying three contour plots to predict the best combination region. The extrudates were obtained under the following optimum factors: FM (%) = 16.94, CHC (%) = 0.095 and T (°C) = 141.89. The predicted extrusion processing factors were highly accurate, yielding an expanded nixtamalized snack with 158.87 mg·kg(-1) TA (estimated: 160 mg·kg(-1)), an EI of 3.19 (estimated: 2.66), and color parameter b of -0.44 (estimated: 0.10).