RESUMEN
To understand the smoke level and NOx emission characteristics of in-use construction machinery in Beijing, we selected 905 construction machines in Beijing from August 2022 to April 2023 to monitor the emission level of smoke and NOx. The exhaust smoke level and excessive emission situation of different machinery types were identified, and their NOx emission levels were monitored according to the free acceleration method. We investigated the correlation of NOx and smoke emission, and proposed suggestions for controlling pollution discharge from construction machinery in the future. The results show that the exhaust smoke level was 0-2.62 m-1, followed a log-normal distribution (µ = -1.73, δ = 1.09, R2 = 0.99), with a 5.64% exceedance rate. Differences were observed among machinery types, with low-power engine forklifts showing higher smoke levels. The NOx emission range was 71-1516 ppm, followed a normal distribution (µ = 565.54, δ = 309.51, R2 = 0.83). Differences among machinery types were relatively small. Engine rated net power had the most significant impact on NOx emissions. Thus, NOx emissions from construction machinery need further attention. Furthermore, we found a weak negative correlation (p < 0.05) between the emission level of smoke and NOx, that is the synergic emission reduction effect is poor, emphasizing the need for NOx emission limits. In the future, the oversight in Beijing should prioritize phasing out China â and China â ¡ machinery, and monitor emissions from high-power engine China â ¢ machinery.
Asunto(s)
Contaminantes Atmosféricos , Monitoreo del Ambiente , Humo , Beijing , Monitoreo del Ambiente/métodos , Contaminantes Atmosféricos/análisis , Humo/análisis , Emisiones de Vehículos/análisis , Óxidos de Nitrógeno/análisis , Industria de la ConstrucciónRESUMEN
INTRODUCTION: Tower cranes are commonly employed in construction projects, despite presenting significant hazards to the workforce involved. METHOD: To address these safety concerns, a Knowledge-Based Decision-Support System for Safety Risk Assessment (KBDSS-SRA) has been developed. The system's capacity to thoroughly evaluate associated risks is illustrated through its utilization in various construction endeavors. RESULTS: The system accomplishes the following goals: (1) compiles essential risk factors specific to tower crane operations, (2) identifies critical safety risks that jeopardize worker well-being, (3) examines and assesses the identified safety risks, and (4) automates the labor-intensive and error-prone processes of safety risk assessment. The KBDSS-SRA assists safety management personnel in formulating well-grounded decisions and implementing effective measures to enhance the safety of tower crane operations. PRACTICAL APPLICATIONS: This is facilitated by an advanced computerized tool that underscores the paramount significance of safety risks and suggests strategies for their future mitigation.
Asunto(s)
Administración de la Seguridad , Humanos , Medición de Riesgo/métodos , Administración de la Seguridad/métodos , Industria de la Construcción , Salud Laboral , Accidentes de Trabajo/prevención & control , Automatización , Técnicas de Apoyo para la Decisión , Bases del ConocimientoRESUMEN
INTRODUCTION: Several studies have assessed and validated the impact of exoskeletons on back and shoulder muscle activation; however, limited research has explored the role that exoskeletons could play in mitigating lower arm-related disorders. This study assessed the impact of Ironhand, an active hand exoskeleton (H-EXO) designed to reduce grip force exertion, on worker exertion levels using a two-phase experimental design. METHOD: Ten male participants performed a controlled, simulated drilling activity, while three male participants completed an uncontrolled concrete demolition activity. The impact of the exoskeleton was assessed in terms of muscle activity across three different muscles using electromyography (EMG), perceived exertion, and perceived effectiveness. RESULTS: Results indicate that peak muscle activation decreased across the target muscle group when the H-EXO was used, with the greatest reduction (27%) observed in the Extensor Carpi Radialis (ECR). Using the exoskeleton in controlled conditions did not significantly influence perceived exertion levels. Users indicated that the H-EXO was a valuable technology and expressed willingness to use it for future tasks. PRACTICAL APPLICATIONS: This study showcases how glove-based exoskeletons can potentially reduce wrist-related disorders, thereby improving safety and productivity among workers. Future work should assess the impact of the H-EXO in various tasks, different work environments and configurations, and among diverse user groups.
Asunto(s)
Electromiografía , Dispositivo Exoesqueleto , Mano , Humanos , Masculino , Proyectos Piloto , Adulto , Mano/fisiología , Fuerza de la Mano/fisiología , Músculo Esquelético/fisiología , Adulto Joven , Esfuerzo Físico/fisiología , Análisis y Desempeño de Tareas , Industria de la Construcción/instrumentaciónRESUMEN
INTRODUCTION: Active back-support exoskeletons are gaining more awareness as a solution to the prevalence of work-related musculoskeletal disorders in the construction industry. This study aims to understand the factors that influence the adoption of active back-support exoskeletons in the construction industry. METHOD: A literature review was conducted to gather relevant adoption factors related to exoskeleton implementation. Building on the TOE (Technology, Organization, and Environment) framework, two rounds of the survey via the Delphi technique were administered with 13 qualified industry professionals to determine the most important adoption factors using the relative importance index. Through semi-structured interviews, the professionals expressed their perspectives on the impact of active back-support exoskeletons on the construction industry. RESULTS: Important factors included 18 facilitators and 21 barriers. The impact of the exoskeletons in the construction industry was categorized into expected benefits, barriers, solutions, adjustment to technology, implementation, and applicable tasks. CONCLUSIONS: This study identified the factors to be considered in the adoption and implementation of active back-support exoskeletons in the construction industry from the perspective of stakeholders. The study also elucidates the impact of active exoskeletons on construction organizations and the broader environment. PRACTICAL APPLICATIONS: This study provides useful guidance to construction companies interested in adopting active back-support exoskeletons. Our results will also help manufacturers of active back-support exoskeletons to understand the functional requirements and adjustments required for utilization in the construction industry. Lastly, the study expands the application of the TOE framework to the adoption of active back-support exoskeletons in the construction industry.
Asunto(s)
Industria de la Construcción , Técnica Delphi , Dispositivo Exoesqueleto , Enfermedades Musculoesqueléticas , Humanos , Enfermedades Musculoesqueléticas/prevención & control , Enfermedades Profesionales/prevención & control , Encuestas y CuestionariosRESUMEN
This article presents the results of the geoarchaeological study of earthen building materials used in a Tartessic public building at Casas del Turuñuelo. The construction dates back to the fifth century BCE and is one of the monumental buildings of Tartessic culture, characterized by its complex architecture, prestige goods, and intentional destruction after a feast and animal sacrifice. We applied an integrated methodology combining macro and micro approaches to investigate earthen construction processes, such as techniques, labour organization, workers' specialization, and environmental exploitation. The sample mainly consists of mudbricks, but we also include other forms of earthen materials such as mud plasters, mud mortars, and geological soils for comparison. In total, 64 samples from different building parts were studied through X-ray fluorescence, X-ray diffraction, thin-section petrography, and CHN analyses. The results reveal that the workforce involved in the construction process used different resources and presented different skill levels, but was centrally planned and organized. This study reflects on the communities' knowledge of the environment, the logistic effort and technical skill employed in the building process, and the existence of strong political structures capable of managing the erection of the complex Tartessic buildings.
Asunto(s)
Materiales de Construcción , España , Humanos , Arqueología , Industria de la ConstrucciónRESUMEN
Introduction: Construction worker safety remains a major concern even as task automation increases. Although safety incentives have been introduced to encourage safety compliance, it is still difficult to accurately measure the effectiveness of these measures. A simple count of accident rates and lower numbers do not necessarily mean that workers are properly complying with safety regulations. To address this problem, this study proposes an image-based approach to monitor moment-by-moment worker safety behavior and evaluate the effects of different safety incentive scenarios. Methods: By capturing workers' safety behaviors using a model integrated with OpenPose and spatiotemporal graph convolutional network, this study evaluated the effects of safety-incentive scenarios on workers' compliance with rules while on the job. The safety incentive scenarios in this study were designed as 1) varying the type (i.e., providing rewards and penalties) of incentives and 2) varying the frequency of feedback about ones' own compliance status during tasks. The effects of the scenarios were compared to the average compliance rates of three safety regulations (i.e., personal protective equipment self-monitoring hazard avoidance, and arranging the safety hook) for each scenario. Results: The results show that 1) rewarding a good-compliance is more effective when there is no feedback on compliance status, and 2) penalizing non-compliance is more effective when there are three feedbacks during the tasks. Discussion: This study provides a more accurate assessment of safety incentives and their effectiveness by focusing on safe behaviors to promote safety compliance among construction workers.
Asunto(s)
Motivación , Salud Laboral , Humanos , Administración de la Seguridad , Industria de la Construcción , Accidentes de Trabajo/prevención & controlRESUMEN
In recent years, foundation pit construction has been rapidly developing in the direction of deep and large-scale, leading to the frequent occurrence of construction accidents. The pit construction process is characterised by a complex environment, high construction risk, and numerous coupling effects between the construction risk factors. In this paper, 23 main accident-causing factors in foundation pit construction are determined based on the six major risk accident types. In addition, the Grey-DEMATEL-Fuzzy comprehensive evaluation method of the risk evaluation model is introduced for better prediction and judgment of risk level, which combines the grey system theory with the method of decision-making experimental analysis, and in the case of inaccurate or incomplete information, the use of less data can achieve the evaluation results with a high degree of reliability, and it will effectively avoid the impact of the lack of information as well as the subjectivity in the process of risk evaluation. Through the Grey-DEMATEL method, the central degree value for each risk indicator factor is calculated, the coupling role and importance of each risk indicator are analysed, and the indicator weights are calculated. Based on the calculated weights, the fuzzy comprehensive evaluation method is used to evaluate the overall risk level. The empirical research on the deep foundation pit construction project of Haitangxi subway station in Chongqing reveals that the excessive lateral earth pressure on the pile wall is the most prominent risk factor. The overall risk level of the construction process is medium, and the risk is within the controllable range. On this basis, corresponding preventive measures can be formulated, providing a basis for risk prevention in the construction of deep foundation pit projects.
Asunto(s)
Industria de la Construcción , Lógica Difusa , Medición de Riesgo/métodos , Humanos , Modelos Teóricos , Factores de Riesgo , ChinaRESUMEN
Construction and demolition activities are significant contributors to waste generation worldwide. As population growth accelerates worldwide, the amount of construction and demolition waste (C&DW) will increase proportionally unless proactive measures are implemented. This study analyzes the evolving research landscape on utilizing Building Information Modeling (BIM) technologies to advance sustainable C&DW management practices. A comprehensive text-mining analysis is conducted on 493 scholarly publications covering evolutions from January 2009 to February 2024 using the PRISMA framework. The research objectives are: (i) to identify key themes in domain of BIM technology in C&DW management using VOSviewer, (ii) to map the temporal evolution of research focus using SciMAT, and (iii) to identify emerging thematic trends.Co-occurrence analysis reveals three major research themes: (i) the use of digital twins and prefabrication for waste reduction, (ii) integrating environmental impact assessments, and (iii) data-driven decision-making. Strategic diagrams produced by SciMAT software uncover shifting priorities over the study period, with "reuse and recycling" emerging as motor themes, and "Prefabrication" (CIT = 481), "Decision Making" (CIT = 66), "Material Passport" (CIT = 92), and "Digital Twin" (CIT = 44) emerging as high-centrality and transversal themes. Temporal evolution mapping unveiled progressive integration of BIM tools such as (i) digital twins (TLS = 34, OCC = 9) and (ii) prefabrication (TLS = 40, OCC = 14), presenting opportunities to optimize waste reduction. This study offers a robust overview of the field, aiming to inform a diverse audience, including researchers from various disciplines, policymakers and industry professionals interested in advancing sustainable practices in C&DW management through innovative digital solutions.
Asunto(s)
Minería de Datos , Administración de Residuos , Administración de Residuos/métodos , Reciclaje , Industria de la ConstrucciónRESUMEN
Whole-body fatigue (WBF) presents a concerning risk to construction workers, which can impact function and ultimately lead to accidents and diminished productivity. This study proposes a new WBF monitoring technique by applying the Critical Power (CP) model, a bioenergetic model, with a wrist-worn heart rate sensor. The authors modified the CP model to calculate WBF from the percentage of heart rate reserve (%HRR) and generated a personalized model via WBF perception surveys. Data were collected for two days from 33 workers at four construction sites. The results showed that the proposed technique can monitor field workers' perceived WBF with a mean absolute error of 12.8% and Spearman correlation coefficient of 0.83. This study, therefore, demonstrates the viability of wearable WBF monitoring on construction sites to support programs aimed at improving workplace safety and productivity.
Asunto(s)
Fatiga , Frecuencia Cardíaca , Dispositivos Electrónicos Vestibles , Humanos , Frecuencia Cardíaca/fisiología , Adulto , Masculino , Industria de la Construcción/instrumentación , Monitoreo Fisiológico/instrumentación , Monitoreo Fisiológico/métodos , Femenino , Persona de Mediana Edad , Adulto Joven , Lugar de Trabajo , Salud LaboralRESUMEN
In current construction waste resource management processes, the effect of government supervision is unclear, and illegal treatment and low-quality reproduction of recycling and reprocessing enterprises by construction units are common. To improve the degree of resource utilization of construction waste and deeply explore the role of its key influencing factors, a tripartite evolutionary game model of construction waste resource treatment in which the government, construction units, and recycling and reprocessing enterprises are the research objects that considers public participation factors to be established. MATLAB is used to simulate the sensitivity of relevant parameters. The results show that: (1) An increase in government fines can regulate the behavior of enterprises; (2) Low government subsidies are conducive to the development of a tripartite stability strategy; and (3) An increase in the cost difference between the two strategies of the enterprise will weaken its willingness to carry out green operations (and after the cost difference exceeds the threshold, the enterprise will refuse to carry out green operations); (4) The reputation value brought by the public and the additional value added by reputation under the contrast effect have an incentive effect on the enterprise and the government; and (5) The peak value of the inverted U-shaped curve of government strategy choice is affected by the degree of public participation. Therefore, the government should propose rectifications in terms of fines and subsidies, and both companies can use technological innovation to reduce costs. At the same time, it is necessary to raise stakeholders' awareness of resource utilization and encourage the public to actively participate in supervision. The research conclusions can provide a decision-making reference for improving the utilization of construction waste resources and the efficient treatment of construction waste resources.
Asunto(s)
Reciclaje , Administración de Residuos , Reciclaje/economía , Administración de Residuos/métodos , Administración de Residuos/economía , Teoría del Juego , Simulación por Computador , Industria de la Construcción , Participación de los Interesados , Humanos , Materiales de Construcción/economíaRESUMEN
BACKGROUND: Construction workers are a population that is at risk for mental illnesses such as depression, anxiety, and even suicide due to the high stress and physical demands of their work. This study aimed to determine the prevalence and risk factors for depression, anxiety, and stress among Bangladeshi construction workers. METHODS: From February 2022 to June 2022, community-based cross-sectional research was conducted among construction workers. Survey data was gathered using interviewer administered questionnaires with 502 participants from the construction sites. Data were collected based on the information related to socio-demographics, lifestyle, occupation, health hazards, and mental health (i.e., depression, anxiety, and stress). The results were interpreted using the chi-square test and logistic regression utilizing SPSS statistical software. RESULTS: The study revealed the prevalence rates of depression, anxiety, and stress among construction workers to be 17.9%, 30.3%, and 12%, respectively. Key findings indicate that construction workers who maintained a healthy sleep duration were 64% less likely to be depressed compared to those with poor sleep (AOR = 0.36; 95% CI: 0.21-0.61, p<0.001). Workers who did not experience breathing issues upon starting construction work had a 45% lower likelihood of experiencing depression (AOR = 0.55; 95% CI: 0.32-0.97, p = 0.037) and an 82% lower likelihood of experiencing anxiety (AOR = 0.18; 95% CI: 0.11-0.30, p<0.001). Bricklayer construction workers were 72% less likely to experience stress (AOR = 0.28; 95% CI: 0.08-0.95, p = 0.041), and workers without breathing issues after starting construction work were 66% less likely to experience stress (AOR = 0.34; 95% CI: 0.17-0.66, p = 0.001). CONCLUSIONS: The study found that depression, anxiety, and stress are prevalent among construction workers in Bangladesh, with breathing issues as a significant risk factor. Thus, there is a need for effective measures to reduce these problems and provide a safe working environment for construction workers to ensure their productivity and the country's overall growth.
Asunto(s)
Ansiedad , Depresión , Humanos , Bangladesh/epidemiología , Adulto , Masculino , Estudios Transversales , Factores de Riesgo , Depresión/epidemiología , Prevalencia , Ansiedad/epidemiología , Femenino , Persona de Mediana Edad , Industria de la Construcción , Adulto Joven , Encuestas y Cuestionarios , Estrés Psicológico/epidemiología , Estrés Laboral/epidemiologíaRESUMEN
Fatigue is one of the menaces that contribute to the rising number of construction-related accidents and fatalities in projects. Therefore, the purpose of this study is to identify several strategies that can be adopted to mitigate fatigue in construction projects. This was achieved through a quantitative study. A questionnaire was the main instrument for data collection in the quantitative study. The study revealed that frustration/depression or work pressure is one of the significant causes of fatigue in construction projects. Fatigue risk management education and bonding among workers are some of the underlying strategies that can be used to mitigate the identified causes. Depending on the nature of the fatigue causative elements, the study further established that some mitigation strategies are more effective than others. Therefore, further studies should be conducted by prospective researchers on a range of attributes that may influence the success of fatigue mitigation strategies in construction projects.
Asunto(s)
Industria de la Construcción , Fatiga , Humanos , Fatiga/prevención & control , Nigeria , Encuestas y Cuestionarios , Masculino , Adulto , Salud Laboral , Persona de Mediana Edad , Gestión de Riesgos/métodos , Accidentes de Trabajo/prevención & control , Femenino , Enfermedades Profesionales/prevención & controlRESUMEN
In numerous developing nations, challenges such as insufficient investment in innovation and limited capabilities for conversion impede the growth of the construction sector, thus affecting the overall economic well-being of these regions. This paper focuses on construction industry innovation (CII) and its correlation with region economic development (RED), providing valuable insights to overcome these challenges and promote sustainable economic advancement. This study references existing literature to devise an evaluation indicator system dedicated for CII and RED. It then proceeds with an empirical analysis of the integration and synergy between CII and the economic development across 31 Chinese provinces from 2012 to 2021. Furthermore, this paper employs ArcGIS and Geoda software to meticulously dissect the spatial distribution characteristics underlying this coordination. The main conclusions are succinctly summarized as follows: CII in China is intricately connected to RED, exhibiting a strong connection that diminishes from south to north. Nonetheless, the coordination level between these factors remains relatively low, with notable regional disparities, particularly from southeast to northwest. The primary obstacles to effective coordination are related to innovation input, output, and economic scale. Additionally, spatial correlation analysis demonstrates pronounced regional clustering, showing stability despite slight fluctuations over the study period. This research underscores the concept of coupling coordination between CII and RED, underpinned by scientific analytical methods. The outcomes provide a definitive guide for advancing the transformation and enhancement of the construction industry while promoting RED.
Asunto(s)
Industria de la Construcción , Desarrollo Económico , Invenciones , China , Industria de la Construcción/economía , Invenciones/economía , HumanosRESUMEN
BACKGROUND: Mental health problems disproportionately affect young people in developing countries. However, there is limited research on help-seeking behaviours and the social support systems that improve mental wellbeing among vulnerable youth populations. OBJECTIVE: This mixed-methods study aimed to examine the relationship between social support reciprocity and mental health among young informal construction workers in Nigeria, a population at high-risk for occupational and socioeconomic stressors. METHODS: A cross-sectional survey was administered to 686 informal workers to measure reciprocity, mental health-related quality of life, and covariates. In-depth interviews with 32 participants provided qualitative context. RESULTS: Quantitative analyses showed 25% of participants reported poor mental health. Reciprocity positively predicted mental health after controlling for covariates. Qualitative findings revealed reciprocity occurs directly between individuals as well as indirectly through trade unions and religious groups. Indirect exchanges through groups helped address limitations of direct support due to limited resources. CONCLUSIONS: This study fills important gaps in understanding how social relationships impact mental health in developing country contexts. Findings emphasize the role of collective action and community-based support systems in promoting mental wellbeing among vulnerable populations. Insights can inform culturally relevant, systems-level mental health interventions.
Asunto(s)
Salud Mental , Calidad de Vida , Apoyo Social , Estudios Transversales , Conducta de Búsqueda de Ayuda , Humanos , Masculino , Femenino , Adulto Joven , Industria de la Construcción , Investigación Cualitativa , Encuestas y Cuestionarios , NigeriaRESUMEN
Contractors' low-carbon construction behaviors (CLCB) are pivotal in advancing decarbonization during the construction phase. However, there exists a notable gap in the comprehensive exploration of the multifaceted factors and mechanisms influencing CLCB. Therefore, this study aims to systematically identify the factors influencing CLCB in China, examine the interrelationships among these factors, and pinpoint the key determinants. Based on topic modeling of Latent Dirichlet Allocation (LDA), influencing factors are identified firstly from the pertinent literature. Subsequently, the causality degree and centrality degree between these factors are assessed by the Decision-Making Trial and Evaluation Laboratory (DEMATEL), followed by the establishment of a hierarchical structure using the Interpretive Structural Modeling (ISM) method, culminating in the identification of pivotal factors. Findings reveal that (1) 21 influential factors influencing CLCB are identified. (2) "Incentive policies for relevant stakeholders" and "Low-carbon regulation and supervision" emerge as key influences. (3) CLCB should be guided by policy and subjective awareness, fortified by market and management support, underpinned by technology, and directly driven by economic considerations. This research furnishes valuable insights for promoting low-carbon development during the construction phase, thereby assisting the construction sector in achieving carbon peak and carbon neutrality.
Asunto(s)
Carbono , China , Industria de la ConstrucciónRESUMEN
Airborne respirable crystalline silica (RCS) has been a widely recognized hazard in the United States for nearly 100 years, yet it continues to pose a risk to construction tradespersons, among others. RCS exposures vary widely depending on site conditions and tools and materials used. The proper use of engineering, administrative, and personal protective equipment (PPE) controls can effectively reduce exposure to RCS. Historically, others have reviewed available RCS exposure data among construction trades and reported that there were considerable data gaps and variability that needed to be addressed. This current assessment aimed to synthesize available peer-reviewed exposure studies to determine potential RCS exposures during the use of common construction materials and evaluate to what extent data gaps and variability persist. Twenty-eight studies were identified that reported RCS exposure during construction tasks. After conversion to the unit of µg/m3, reported measurements from samples collected for varying durations ranged from 6.0 to 75,500 µg/m3 for work with concrete, 80 to 4,240 µg/m3 for work with brick, <59 to 10,900 µg/m3 for work with mortar, 90 to 44,370 µg/m3 for work with engineered stone, and 70 to 380 µg/m3 for work with roof tile. To better facilitate pooling data across studies, future researchers should report their sample duration, clarify how time-weighted average (TWA) exposure data are calculated, report the silica content of the material being manipulated, and specify whether samples were collected while the task was performed in isolation or on a worksite where other silica-containing materials were also actively handled. When reporting results as respirable quartz, it is important to note whether any other polymorphic forms of silica were detected. It is ultimately the employer's responsibility to train employees and monitor and control RCS exposures on construction worksites. To do this effectively, it is important to have a clear understanding of the tasks, materials, and site conditions where intervention is most urgently needed.
Asunto(s)
Contaminantes Ocupacionales del Aire , Industria de la Construcción , Materiales de Construcción , Exposición por Inhalación , Exposición Profesional , Dióxido de Silicio , Dióxido de Silicio/análisis , Exposición Profesional/análisis , Exposición por Inhalación/análisis , Exposición por Inhalación/prevención & control , Contaminantes Ocupacionales del Aire/análisis , Humanos , Estados Unidos , Equipo de Protección Personal , Monitoreo del Ambiente/métodosRESUMEN
This study explores the factors influencing unsafe behaviors among decorators. The study begins with a literature review on unsafe behaviors among construction workers, compiling a checklist of factors specific to decorators. Utilizing exploratory factor analysis (EFA), a measurement scale for these factors is developed. Subsequently, stepwise regression analysis (SRA) is conducted to validate relationships and identify crucial factors. Results categorize influencing factors into three dimensions: personal, organizational and environmental. Non-compliance with safety procedures and protocols is found to correlate directly with increased unsafe behavior at an individual level. Additionally, internal safety regulations within companies are identified as having a direct negative impact on unsafe behaviors at the organizational level. This study enhances our understanding of unsafe behaviors among decorators and offers recommendations for mitigation.
Asunto(s)
Industria de la Construcción , Salud Laboral , Humanos , Masculino , Adulto , Encuestas y Cuestionarios , Administración de la Seguridad , Análisis Factorial , Persona de Mediana Edad , Lugar de Trabajo/psicología , Accidentes de Trabajo/prevención & control , Accidentes de Trabajo/psicologíaRESUMEN
The Ghanaian construction industry faces challenges in managing safety, especially for small and medium-sized enterprises (SMEs) that need more resources. This research addressed the critical need for a positive safety culture framework specifically designed for SMEs in Ghana. The study adopts the Delphi research approach, which involves a series of questionnaire 'rounds' to gather and refine information and develop a collaborative safety culture framework with SME stakeholders. The study employed a mixed-methods strategy, harnessing quantitative and qualitative data to meet the research goals. The critical components of the developed framework included safety commitment, adaptability, information, awareness, culture, and performance. The research offered evidence-based recommendations for effective positive safety practices across Ghana's SMEs by analysing the relationship between these interventions and safety outcomes. Applying the framework should reduce workplace accidents and foster a positive safety culture that aligns with international best practices.
Asunto(s)
Industria de la Construcción , Administración de la Seguridad , Ghana , Humanos , Técnica Delphi , Encuestas y Cuestionarios , Salud Laboral/normas , Cultura OrganizacionalRESUMEN
Increasingly, information technology facilitates the storage and management of data useful for risk analysis and event prediction. Studies on data extraction related to occupational health and safety are increasingly available; however, due to its variability, the construction sector warrants special attention. This review is conducted under the research programs of the National Institute for Occupational Accident Insurance (Inail). OBJECTIVES: The research question focuses on identifying which data mining (DM) methods, among supervised, unsupervised, and others, are most appropriate for certain investigation objectives, types, and sources of data, as defined by the authors. METHODS: Scopus and ProQuest were the main sources from which we extracted studies in the field of construction, published between 2014 and 2023. The eligibility criteria applied in the selection of studies were based on the Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA). For exploratory purposes, we applied hierarchical clustering, while for in-depth analysis, we used principal component analysis (PCA) and meta-analysis. RESULTS: The search strategy based on the PRISMA eligibility criteria provided us with 63 out of 2234 potential articles, 206 observations, 89 methodologies, 4 survey purposes, 3 data sources, 7 data types, and 3 resource types. Cluster analysis and PCA organized the information included in the paper dataset into two dimensions and labels: "supervised methods, institutional dataset, and predictive and classificatory purposes" (correlation 0.97-8.18 × 10-1; p-value 7.67 × 10-55-1.28 × 10-22) and the second, Dim2 "not-supervised methods; project, simulation, literature, text data; monitoring, decision-making processes; machinery and environment" (corr. 0.84-0.47; p-value 5.79 × 10-25--3.59 × 10-6). We answered the research question regarding which method, among supervised, unsupervised, or other, is most suitable for application to data in the construction industry. CONCLUSIONS: The meta-analysis provided an overall estimate of the better effectiveness of supervised methods (Odds Ratio = 0.71, Confidence Interval 0.53-0.96) compared to not-supervised methods.
Asunto(s)
Industria de la Construcción , Minería de Datos , Salud Laboral , Administración de la Seguridad , Minería de Datos/métodos , Humanos , Administración de la Seguridad/métodosRESUMEN
Plastic production has increased manifold over the last decade, with worldwide production reaching 400 million tonnes in 2021, and the trend is estimated to have a sharp rise in the future. Apart from being non-biodegradable, plastics are essentially durable, which makes waste plastic disposal extremely difficult and poses a threat to solid waste management. Disposal methods, including incinerating, landfilling, disposal into water bodies, etc., are having hazardous environmental impacts. Hence, plastic recycling is essential for ensuring sustainability. The construction industry is a major contributor to global warming primarily due to the Portland cement production emitting 6% of global CO2 production. Growing awareness has emphasized partial replacement of Portland cement with other binders, such as metakaolin, fly ash, slag, etc., to be used in conventional composites or complete replacement to yield geopolymer composites. Waste plastics can be used in geopolymer concrete (GPC) as a partial or complete replacement of natural aggregates or added as fibers. Based on the above background, various researchers have incorporated plastics in GPC in the form of aggregate replacement or fiber addition, justifying sustainability and enhancing GPC characteristics. Plastic supplementation in GPC is a relatively new research domain. An attempt has been made through the current review work to develop a comprehensive database established on various concrete characteristics through the globally available research performances involving various forms of plastic incorporation in GPC yielding plastic-supplemented GPC (PSGPC). A detailed plastic classification and varying forms are poised, with identified plastics elicited from its global acceptance so far in PSGPC production. Through various PSGPC characteristics like fresh, physical, mechanical, durability, and microstructural analysis with different plastic types and forms, the optimal waste plastic disposable range is entrenched justifying eco-friendly and sustainable concrete yield.