RESUMEN
Herein, a novel acylhydrazone biosorbent (GSL) with abundant three-dimensional porous structure was successfully prepared by using low-cost starch as raw material for water pollution remediation applications. Various analytical techniques were applied to characterize the morphological structure and chemical composition. Interestingly, the adsorption efficiency of the adsorbent towards Malachite green (MG), Safranin O (SO), Cu2+, and sulfide in the static adsorption experiment was extremely high due to presence of ample functional groups. Additionally, the adsorption isotherm and kinetic experiments revealed that the adsorption processes were based on monolayer chemisorption. The maximum sorption amounts were 2237.4961 mg/g for SO, 2101.6610 mg/g for MG, 410.7019 mg/g for Cu2+, and 483.0194 mg/g for sulfides at 298.15 k. The thermodynamic analysis also demonstrated that all adsorption processes were spontaneous heat processes. The adsorption mechanism was analyzed by FTIR, SEM-EDAX and XPS. The adsorption of SO onto GSL reached 1025.8617 mg/g in continuous adsorption experiments, and the experimental data were fitted through the Thomas model and Yoon-Nelson model. Furthermore, the GSL showed good reusability and salt resistance. Importantly, starch-based acylhydrazone as the adsorbent for the simultaneous removal of hazardous dyes, heavy metal ions and sulfhides has not yet been seen reported.
RESUMEN
This is the first successful report on selenium bio-attenuation to satisfy drinking water regulations as per Indian Standards (10 µg/L) in the presence of concomitant nitrate and sulfate from water sources utilizing a fixed bed bioreactor. The bioreactor was immunized with blended microbial culture and worked in downï¬ow mode under anoxic conditions at 30 ± 2 °C for around 190 days under varying inï¬uent selenate (100-500 µg/L as selenium), nitrate (50 mg/L), sulfate concentrations (as per selenium removal) and necessary dose of acetic acid (as COD, a carbon source) in synthetic groundwater, operated at an empty bed contact time (EBCT) of 45-120 min. After supplying an adequate dosage of sulfate and alteration of EBCT, selenium was found to comply with drinking water regulations and nitrate was completely removed. X-ray diffraction and transmission electron microscopy analyses depicted nanocrystalline selenium sulfides (SeS and SeS2) formation as the possible mechanisms of selenium removal. Extended toxicity characteristic leaching procedure (TCLP) extractions confirmed a maximum selenium leaching of 52 and 282 µg/L during anoxic and oxic extractions, respectively. Long-term column leaching (>3-month equilibration) under aerobic conditions at pH 7 confirmed the produced precipitate to be essentially stable (â¼0.14% Se leaching). This work exhibits the synchronous bioremoval of selenium and its co-anions from contaminated water complying with drinking water standards, and leaving a stable and non-hazardous selenium-laden biosludge.
RESUMEN
Cobalt-based sulfides (CSs) are generally regarded as potentially valuable anode materials for sodium-ion batteries (SIBs) due to their excellent theoretical capacity and natural abundance. Nevertheless, their slow reaction kinetics and poor structural stability restrict the practical application of the materials. In this study, the dual-carbon-confined Se-CoS2@NC@C hollow nanocubes with anion doping are synthesized using ZIF-67 as the substrate by resorcin-formaldehyde (RF) encapsulation and subsequent carbonization and sulfurization/selenization. RF- and ZIF-67-derived dual-carbon skeleton hollow structures with a robust carbon skeleton and abundant internal space minimize cyclic stress, mitigate volume changes and maintain the structural integrity of the material. More importantly, Se doping increases the lattice spacing of CoS2, weakens the strength of Co-S bonds, and modulates the electronic structure around Co atoms, thereby optimizing the adsorption energy of the material. As a result, the hollow nanocubes of Se-CoS2@NC@C demonstrates excellent electrochemical performance as the anode for SIBs, delivering a high reversible capacity of 549.4 mAh g-1 at 0.5 A g-1 after 100 cycles and a superb rate performance (541.1 mAh g-1 at 0.2⯠A⯠g-1, and 393.3 mAh g-1 at 5â¯Aâ¯g-1). This study proposes a neoteric strategy for synthesizing advanced anodes for SIBs through the synergy of anion doping engineering and dual-carbon confinement strategy.
RESUMEN
We herein report successful syntheses of both nickel cobalt sulfide (NCS) and its composite with zeolite (NCS@Z) using a solvothermal method. Techniques such as EDX analysis, SEM, and molar ratio determination were used for product characterization. The incorporation of NCS significantly changed the surface roughness and active sites of the zeolite, improving the efficiency of methylene blue degradation and its reusability, especially under UV irradiation. In comparing the pseudo-first order rates, the highest degradation efficiency of methylene blue was achieved with NCS-2@Z, having a degradation extent of 91.07% under UV irradiation. This environmentally friendly approach offers a promising solution for the remediation of methylene blue contamination in various industries.
RESUMEN
As the most promising anodes for Na+/K+ batteries (SIBs/PIBs), transitional metal sulfides present the advantages of high capacity, straightforwardly-controlled morphology and abundant redox reaction sites. However, maintaining the structural integrity of the electrode materials during cycling and improving the cycle life still face great challenges. Herein, CoS2@NPSC@MoS2 nano-spindle heterostructure with multiple heteroatoms co-doped carbon layers coupled with Janus metal sulfides (CoS2 and MoS2) were successfully fabricated via the successive organic coating, gas-phase phosphorization and the final hydrothermal reaction processes. Benefiting from the uniformly dispersed CoS2 nanocrystals in the interior of carbon layer and the MoS2 nanosheets arrays in the exterior, Na+/K+ diffusion distances are remarkedly shortened and the reaction kinetics are greatly improved, which also provide more active sites on the surface for exposure to the electrolyte. The presence of heterogeneous atomic N/P/S co-doped carbon layer greatly improves the electrochemical conductivity of the heterostructure and provide additional buffer space for volume changes, which is conducive to retaining the integrity of the electrode structure during the cycling processes. When used as the anode material for SIBs/PIBs, it reached the reversible specific capacity of 340.44 mAh g-1 at 5.0 A g-1 after 1000 cycles for SIBs and 37.53 mAh g-1 at 5.0 A g-1 after 800 cycles for PIBs. This work demonstrates a reliable and simple strategy for the rational design of Janus metal sulfides heterostructures for high performance Na+/K+ storage application.
RESUMEN
A convenient and practical multicomponent strategy for the sulfenoamination of alkenes was realized, which using free-thiols as the sulfur-reagent, NIS both as radical initiator and an N-nucleophile. This protocol excellent in terms of transition-metal-free, good functional group tolerance, easily available substrates and facile scale-up. And provided a direct- and general way to synthesize various ß-succinimide sulfides with high regioselectivity.
RESUMEN
Sulfidation of nanoscale zerovalent iron (nZVI) can enhance particle performance. However, the underlying mechanisms of nZVI sulfidation are poorly known. We studied the effects of Fe2+ on 24-h dynamics of nZVI sulfidation by HS- using a dosed S to Fe molar ratio of 0.2. This shows that in the absence of Fe2+, HS- rapidly adsorbed onto nZVI particles and reacted with surface iron oxide to form mackinawite and greigite (<0.5 h). As nZVI corrosion progressed, amorphous FeSx in solution deposited on nZVI, forming S-nZVI (0.5-24 h). However, in the initial presence of Fe2+, the rapid reaction between HS- and Fe2+ produced amorphous FeSx, which deposited on the nZVI and corroded the surface iron oxide layer (<0.25 h). This was followed by redeposition of colloidal iron (hydr)oxide on the particle surface (0.25-8 h) and deposition of residual FeSx (8-24 h) on S-nZVI. S loading on S-nZVI was 1 order of magnitude higher when Fe2+ was present. Surface characterization of the sulfidated particles by TEM-SAED, XPS, and XAFS verified the solution dynamics and demonstrated that S2- and S22-/Sn2- were the principal reduced S species on S-nZVI. This study provides a methodology to tune sulfur loading and S speciation on S-nZVI to suit remediation needs.
RESUMEN
An exceptional efficiency of pyrazine-annelated porphyrin as a general photocatalyst for the oxidation of organic sulfides is demonstrated. It is shown that phosphonate-substituted pyrazinoporphyrin 2H-1 brings together sufficient photostability and high efficiency in the aerobic photooxidation of a series of various sulfides. The influence of the reaction conditions onto the efficiency of homogeneous sulfide photooxidation in the presence of the PS was investigated and strong dependence on the solvent system was observed. The use of methanol is required for the photocatalytic sulfoxidation and the ratio of the alcohol/other solvent can significantly affect the conversion and selectivity of the reaction. The application of the prepared photosensitizer (PS) in 0.001 mol% loading allowed achieving complete conversion (97-100%, turnover number up to 100000, turnover frequency up to 6250 h-1) of substrates bearing substituents of different nature, namely aromatic and aliphatic sulfides with donor or acceptor substituents and substituents prone to oxidation, as well as cyclic sulfides. The selectivity of the of the corresponding sulfoxides formation of 96-100% was revealed. Finally, a gram-scale synthesis of several sulfoxides was successfully performed with the PS under investigation, providing desired products in 66-96% yield with over 98% purity.
RESUMEN
Inevitable leaching and corrosion under anodic oxidative environment greatly restrict the lifespan of most catalysts with excellent primitive activity for oxygen production. Here, based on Fick' s Law, we present a surface cladding strategy to mitigate Ni dissolution and stabilize lattice oxygen triggering by directional flow of interfacial electrons and strong electronic interactions via constructing elaborately cladding-type NiO/NiS heterostructure with controlled surface thickness. Multiple in-situ characterization technologies indicated that this strategy can effectively prevent the irreversible Ni ions leaching and inhibit lattice oxygen from participating in anodic reaction. Combined with density functional theory calculations, we reveal that the stable interfacial O-Ni-S arrangement can facilitate the accumulation of electrons on surficial NiO side and weaken its Ni-O covalency. This would suppress the overoxidation of Ni and simultaneously fixing the lattice oxygen, thus enabling catalysts with boosted corrosion resistance without sacrificing its activity. Consequently, this cladding-type NiO/NiS heterostructure exhibits excellent performance with a low overpotential of 256 mV after 500 h. Based on Fick's law, this work demonstrates the positive effect of surface modification through precisely adjusting of the oxygen-sulfur exchange process, which has paved an innovative and effective way to solve the instability problem of anodic oxidation.
RESUMEN
Designing robust, efficient and inexpensive trifunctional electrocatalysts for the oxygen reduction reaction (ORR), oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is significant for rechargeable zinc-air batteries and water-splitting devices. To this end, constructing heterogenous structures based on transition metals stands out as an effective strategy. Herein, a dual-phase Co9S8-CoMo2S4 heterostructure grown on porous N, S-codoped carbon substrate (Co9S8-CoMo2S4/NSC) via a one-pot synthesis is investigated as the trifunctional ORR/OER/HER electrocatalyst. The optimized Co9S8-CoMo2S4/NSC2 exhibits that ORR has a half-wave potential of 0.86 V (vs. RHE) and the overpotentials at 10 mA cm-2 for OER and HER are 280 and 89 mV, respectively, superior to most transition-metal based trifunctional electrocatalysts reported to date. The Co9S8-CoMo2S4/NSC2-based zinc-air battery (ZAB) has a high open-circuit voltage (1.41 V), large capacity (804 mA h g-1) and highly stable cyclability (97 h at 10 mA cm-2). In addition, the prepared Co9S8-CoMo2S4/NSC2-based ZAB in series can self-drive the corresponding water electrolyzer. The dual-phase Co9S8-CoMo2S4 heterostructure provides not only multi-type active sites to drive the ORR, OER and HER, but also high-speed charge transfer channels between two phases to improve the synergistic effect and reaction kinetics.
RESUMEN
The construction of S-scheme heterojunctions, which offers a promising approach for spatially separating photogenerated charge carriers with high redox potentials and multimolecular activation, represents a viable modification strategy in photocatalytic applications. However, the prevalent insufficient contact areas between two components result in low interface charge transfer efficiency, thereby impeding the photocatalytic performance of such heterostructures. Herein, we address this limitation by introducing a unique mCN@mPDIP molecular heterojunction through a pH-triggered molecule self-assembly eutectoid technique, enabling intimate interface contact and promoting highly efficient interfacial charge transfer following an S-scheme mechanism. Consequently, the mCN@mPDIP molecular heterojunction achieves significantly improved charge separation efficiency and higher concentration of active carriers compared to typical bCN-bPDIP bulk heterojunction and nCN/nPDIP nano heterojunction. Combined with the effective sulfide activation on mPDIP sites and O2 activation on mCN sites, the resulting mCN@mPDIP demonstrates outstanding activity in the photocatalytic aerobic oxidation of sulfides into sulfoxides without any redox mediators.
RESUMEN
Selective CO2-to-CO photoreduction is under intensive research and requires photocatalysts with tuned microstructures to accelerate the reaction kinetics. Here, we report CuInS2 nanosheet arrays with sulfur vacancies (VS) grown on the two-dimensional (2D) support of Ti3C2Tx MXene for CO2-to-CO photoreduction. Our results reveal that the use of Ti3C2Tx induces strong support effect, which causes the hierarchical nanosheet arrays growth of CuInS2 and simultaneously leads to charge transfer from CuInS2 to Ti3C2Tx support, resulting in VS formed in CuInS2. The strong support effect based on Ti3C2Tx is proven to be applicable to prepare a series of different metal indium sulfide arrays with VS. CuInS2 nanosheet arrays with VS supported on Ti3C2Tx benefit the photocatalytic selective reduction of CO2 to CO, manifesting a remarkable over 14.8-fold activity enhancement compared with pure CuInS2. The experimental and computational investigations pinpoint that VS of CuInS2 resulting from the support effect of Ti3C2Tx lowers the barrier of the rate-limiting step of *COOH â *OH + *CO, which is the key to the photoactivity enhancement. This work demonstrates MXene support effects and offers an effective approach to regulate the atomic microstructure of metal sulfides toward enhancing photocatalytic performance.
RESUMEN
Heterostructures endow electrochemical hybrids with promising energy storage properties owing to synergistic effects and interfacial interaction. However, developing a facile but effective approach to maximize interface effects is crucial but challenging. Herein, a bimetallic sulfide/carbon heterostructure is realized in a confined carbon network via a high-throughput template-assisted strategy to induce highly active and stable electrode architecture. The designed heterostructures not only yield abundant interconnected Co9S8/MoS2/N-doped carbon (Co9S8/MoS2/NC) heterojunctions with continuous channels for ion/electron transfer but maintain excellent conversion reversibility. Serving as anode for sodium storage, the Co9S8/MoS2/NC framework displayed excellent sodium storage properties (reversible capacity of 480 mAh/g after 100 cycles at 0.2 A/g and 286.2 mAh/g after 500 cycles at 2 A/g). Given this, this study can guide future design protocols for interface engineering by forming dynamic channels of conversion reaction kinetics for potential applications in high-performance electrodes.
RESUMEN
The development of core-shelled heterostructures with the unique morphology can improve the electrochemical properties of hybrid supercapacitors (HSC). Here, CuCo2S4 nanowire arrays (NWAs) are vertically grown on nickel foam (NF) utilizing hydrothermal synthesis. Then, CoMo-LDH nanosheets are uniformly deposited on the CuCo2S4 NWAs by electrodeposition to obtain the CoMo-LDH@CuCo2S4 NWAs/NF electrode. Due to the superior conductivity of CuCo2S4 (core) and good redox activity of CoMo-LDH (shell), the electrode shows excellent electrochemical properties. The electrode's specific capacity is 1271.4 C g-1 at 1 A g-1, and after 10, 000 cycles, its capacity retention ratio is 92.2 % at 10 A g-1. At a power density of 983.9 W kg-1, the CoMo-LDH@CuCo2S4 NWAs/NF//AC/NF device has an energy density of 52.2 Wh kg-1. This indicates that CoMo-LDH@CuCo2S4/NF has a great potential for supercapacitors.
RESUMEN
Conversion and alloying-type transitional metal sulfides have attracted significant interests as anodes for Potassium-ion batteries (PIBs) and Sodium-ion batteries (SIBs) due to their high theoretical capacities and low cost. However, the poor conductivity, structural pulverization, and high-volume expansions greatly limit the performance. Herein, Co1-xS/ZnS hollow nanocube-like heterostructure decorated on reduced graphene oxide (Co1-xS/ZnS@rGO) composite is fabricated through convenient hydrothermal and post-heat vulcanization techniques. This unique composite can provide a more stable conductive network and shorten the diffusion length of ions, which exhibits a remarkable initial charge capacity of 638.5 mA h g-1 at 0.1 A g-1 for SIBs and 606 mA h g-1 at 0.1 A g-1 for PIBs, respectively; It is worth noting that the composite presents remarkable long stable cycle performance in PIBs, which initially delivered 274 mA h g-1 and sustained the charge capacity up to 245 mA h g-1 at high current density of 1 A g-1 after 2000 cycles. A series of in situ/ex situ detections and first principle calculations further validate the high potassium ions adsorption ability of Co1-xS/ZnS anode materials with high diffusion kinetics. This work will accelerate the fundamental construction of bimetallic sulfide hollow nanocubes heterostructure electrodes for energy storage applications.
RESUMEN
The characterization and evolution of corrosion products deposited on/around MnSs, a typical kind of inclusive particle embedded in AISI 304 stainless steel, was analyzed using a quasi-in-situ method in a 3.5 wt.% NaCl solution. On/around the MnS inclusion, a corrosion product layer with spinel Fe3-xCrxO4 as the main component was formed, with a thickness of several hundred nanometers. Below the layer, there was a cavity layer in which part of the MnS remained, forming secondary pitting along the MnS/matrix boundary. The mechanism of corrosion product deposition and evolution accompanied by MnS dissolution, as well as the characteristics of the corrosion products, are discussed.
RESUMEN
Members of the genus Shewanella are known for their versatile electron accepting routes, which allow them to couple decomposition of organic matter to reduction of various terminal electron acceptors for heterotrophic growth in diverse environments. Here, we report autotrophic growth of Shewanella oneidensis MR-1 with photoelectrons provided by illuminated biogenic CdS nanoparticles. This hybrid system enables photosynthetic oscillatory acetate production from CO2 for over five months, far exceeding other inorganic-biological hybrid system that can only sustain for hours or days. Biochemical, electrochemical and transcriptomic analyses reveal that the efficient electron uptake of S. oneidensis MR-1 from illuminated CdS nanoparticles supplies sufficient energy to stimulate the previously overlooked reductive glycine pathway for CO2 fixation. The continuous solar-to-chemical conversion is achieved by photon induced electric recycling in sulfur species. Overall, our findings demonstrate that this mineral-assisted photosynthesis, as a widely existing and unique model of light energy conversion, could support the sustained photoautotrophic growth of non-photosynthetic microorganisms in nutrient-lean environments and mediate the reversal of coupled carbon and sulfur cycling, consequently resulting in previously unknown environmental effects. In addition, the hybrid system provides a sustainable and flexible platform to develop a variety of solar products for carbon neutrality.
RESUMEN
The reactivity and stability of zero-valent iron (ZVI) and sulfidated zero-valent iron (S-ZVI) are inherently contradictory. Iron sulfides (FeSX) on the S-ZVI surface play multiple roles, including electrostatic adsorption and catalyzing reduction. We proposed to balance the reactivity and air stability of S-ZVI by regulating FeSX. Benefiting from the superior coordination and accelerate electron transport capabilities of phosphate, herein, eco-friendly ammonium dihydrogen phosphate (ADP) was employed to synthesize N, P, and S-incorporated ZVI (NPS-ZVI) and regulate the FeSX. Raman, FTIR, XPS, and density functional theory (DFT) calculations were combined to reveal that HPO42- acts as the main P species on the Fe surface. The superior reactivity of NPS-ZVI was quantified by kobs, kSA, and kM of Cr(VI), which were 210.77, 27.44, and 211.17-fold than ZVI, respectively. NPS-ZVI demonstrated excellent reusability, with no risk of secondary pollution. Critically, NPS-ZVI could effectively maintain FeSX stability under the combination of diffusion limitation and surface protection mechanisms of ADP. The superior reactivity of NPS-ZVI was attributed to the fact that ADP maintains FeSX stability and accelerates electron transport. This study provides a novel strategy in balancing the reactivity and air stability of S-ZVI and offers theoretical support for material modification.
RESUMEN
Ternary metal sulfides with suitable band gaps, high physicochemical stability, and unique two-dimensional (2D) nanostructures are expected to be the next-generation high-performance gas sensors following the MOS type. Doping engineering is utilized as an effective strategy to improve the semiconductor surface activity and enhance its gas-sensitive properties. In this paper, the energy band structure and surface chemical oxygen of ZnIn2S4 (ZIS) materials was tuned by selectively introducing substitutional Cd to replace the Zn sites in ZIS crystals. Meanwhile, the introduction of Cd-ions brings more abundant S vacancy defects, enhances the acid-base interactions at the interface, and pushes the extent of surface redox reactions. In addition, by combining the strong adsorption of ZIS to triethylamine, the CdxZn1-xIn2S4 nanosheets achieved highly improved sensing properties, including better response (63.38-100 ppm), enhanced selectivity (STEA/sother = 12.9), and accelerated response/recovery (4 s/32 s). The results confirm the feasibility of developing low-cost, high-performance 2D metal sulfide gas sensing materials through rational structural design and optimization.
RESUMEN
Lithium-ion batteries with transition metal sulfides (TMSs) anodes promise a high capacity, abundant resources, and environmental friendliness, yet they suffer from fast degradation and low Coulombic efficiency. Here, a heterostructured bimetallic TMS anode is fabricated by in situ encapsulating SnS2/MoS2 nanoparticles within an amphiphilic hollow double-graphene sheet (DGS). The hierarchically porous DGS consists of inner hydrophilic graphene and outer hydrophobic graphene, which can accelerate electron/ion migration and strongly hold the integrity of alloy microparticles during expansion and/or shrinkage. Moreover, catalytic Mo converted from lithiated MoS2 can promote the reaction kinetics and suppress heterointerface passivation by forming a building-in-electric field, thereby enhancing the reversible conversion of Sn to SnS2. Consequently, the SnS2/MoS2/DGS anode with high gravimetric and high volumetric capacities achieves 200 cycles with a high initial Coulombic efficiency of >90%, as well as excellent low-temperature performance. When the commercial Li(Ni0.8Co0.1Mn0.1)O2 (NCM811) cathode is paired with the prelithiated SnS2/MoS2/DGS anode, the full cells deliver high gravimetric and volumetric energy densities of 577 Wh kg-1 and 853 Wh L-1, respectively. This work highlights the significance of integrating spatial confinement and atomic heterointerface engineering to solve the shortcomings of conversion-/alloying typed TMS-based anodes to construct outstanding high-energy LIBs.