RESUMEN

Although enhanced performances of photovoltaic devices by embedding metal nanoparticals in charge transport layer, doping into active layer bulk, decorating the active layer surface, and inserting at the interface between semiconductor and the electrode were reported, the effect of incorporating metal NPs at the interface of single crystal semiconductor and perovskite is rarely tackled. Herein the effects of incorporating Ag nanoparticals (AgNPs) at p-Si/MAPbI3 perovskite interface on the photodiode performances were investigated. The results showed that compared with reference device (without AgNPs) the photoresponsivity of the device incorporating AgNPs is greatly improved with the exception for light with wavelengths fall in the spectral range where AgNPs have strong optical absorption. This effect is extremely significant for relatively shorter wavelengths in visible region, and a maximal improvement of around 10.6 times in photoresponsivity was achieved. The physical origin of the exception for spectral range that AgNPs have strong optical absorption is the cancelation of scatter resulted enhancement through AgNPs by band-to-band absorption resulted reduction of photocurrent, in which the generated electron has energy near the fermi level and the hole has large effective mass, which relax by nonradiative recombination, thus making not contribution to the photocurrent. More importantly, the AgNP decorated device showed much faster photo response speed than reference device, and a maximal improvement of around 7.9 times in rise and fall time was achieved. These findings provide a novel approach for high responsive and high speed detection for weak light.

RESUMEN

Highly sensitive infrared photodetectors are needed in numerous sensing and imaging applications. In this paper, we report on extended short-wave infrared (e-SWIR) avalanche photodiodes (APDs) capable of operating at room temperature (RT). To extend the detection wavelength, the e-SWIR APD utilizes a higher indium (In) composition, specifically In0.3Ga0.7As0.25Sb0.75/GaSb heterostructures. The detection cut-off wavelength is successfully extended to 2.6 µm at RT, as verified by the Fourier Transform Infrared Spectrometer (FTIR) detection spectrum measurement at RT. The In0.3Ga0.7As0.25Sb0.75/GaSb heterostructures are lattice-matched to GaSb substrates, ensuring high material quality. The noise current at RT is analyzed and found to be the shot noise-limited at RT. The e-SWIR APD achieves a high multiplication gain of M~190 at a low bias of Vbias=- 2.5 V under illumination of a distributed feedback laser (DFB) with an emission wavelength of 2.3 µm. A high photoresponsivity of R>140 A/W is also achieved at the low bias of Vbias=-2.5 V. This type of highly sensitive e-SWIR APD, with a high internal gain capable of RT operation, provides enabling technology for e-SWIR sensing and imaging while significantly reducing size, weight, and power consumption (SWaP).

RESUMEN

Near-infrared (NIR) organic photodetectors (OPDs), particularly all-polymer-based ones, hold substantial commercial promise in the healthcare and imaging sectors. However, the process of optimizing their active layer composition to achieve highly competitive figures of merit lacks a clear direction and methodology. In this work, celebrity polymer acceptor PY-IT into a more NIR absorbing host system PBDB-T:PZF-V, to significantly enhance the photodetection competence, is introduced. The refined all-polymer ternary broadband photodetector demonstrates superior performance metrics, including experimentally measured noise current as low as 6 fA Hz-1/2, specific detectivity reaching 8 × 1012 Jones, linear dynamic range (LDR) of 145 dB, and swift response speed surpassing 200 kHz, striking a fair balance between sensitivity and response speed. Comprehensive morphological and photophysical characterizations elucidate the mechanisms behind the observed performance enhancements in this study, which include reduced trap density, enhanced charge transport, diminished charge recombination, and balanced electron/hole mobilities. Moreover, the practical deployment potential of the proof-of-concept device in self-powered mode is demonstrated through their application in a machine learning-based cuffless blood pressure (BP) estimation system and in high-resolution computational imaging across complex environments, where they are found to quantitatively rival commercial silicon diodes.

RESUMEN

The nonlinear characteristics of avalanche photodiodes (APDs) inhibit their performance in high-speed communication systems, thereby limiting their widespread application as optical detectors. Existing theoretical models have not fully elucidated complex phenomena encountered in actual device structures. In this study, actual APD structures exhibiting lower linearity than their ideal counterparts were revealed. Simulation analysis and physical inference based on GaN APDs reveal that electrode size is a noteworthy factor influencing response linearity. This discovery expands the nonlinear theory of APDs, suggesting that APD linearity can be enhanced by suppressing the electrode size effect. A physical model was developed to explain this phenomenon, which is attributed to charge accumulation at the edge of the contact layer. Therefore, we proposed an improved APD design that incorporates an additional gap layer and a buffer layer to stabilize the internal gain under high-current-density conditions, thereby enhancing linearity. Our improved APD design increases the linear threshold for optical input power by 4.46 times. This study not only refines the theoretical model for APD linearity but also opens new pathways for improving the linearity of high-speed optoelectronic detectors.

RESUMEN

OBJECTIVE: The primary objective was to develop a concomitant isocratic ultra-performance liquid chromatographic photo-diode array detection method to estimate Upadacitinib and its process-related impurities: impurity-1 and impurity-2. Further validation was conducted and studied for possible degradants under stress environments. MATERIALS AND METHODS: All the chemicals and reagents used were of HPLC (acetonitrile, methanol) and analytical grade (trifluoro acetic acid). The ultra-performance liquid chromatography (Agilent 1290 Infinity II LC system) consists of a quaternary pump, a BEH C18 (50×2.1mm, 1.7µ) column, and photo-diode array detector. The method was developed with acetonitrile: methanol: 0.1% v/v trifluoro acetic acid (50:20:30 v/v/v) mobile phase at 0.2mL/min flow rate within a run time of 5.5min The detection was carried at 231.2nm. RESULTS: The respective retention times achieved were 2.289min (Upadacitinib), 0.972min (Upadacitinib impurity-1), and 3.508min (Upadacitinib impurity-2). The optimized method was validated further, and the linearity range was best fit at 15.0-180.0µg/mL for Upadacitinib and 1.0-12.0µg/mL for both Upadacitinib impurity-1 and 2 respectively. The detection and quantification limits were 4.50µg/mL, 15.00µg/mL (Upadacitinib) and 0.30µg/mL, 1.0µg/mL (Upadacitinib impurity-1 and 2). CONCLUSION: A fast, isocratic, specific, and reproducible ultra-performance liquid chromatographic method was developed and validated for various parameters according to the ICH Q2 (R1) guidelines studies. Stress studies were conducted exposing the sample dilution to various treatments (acid, alkali, peroxide, HPLC water, heat, and UV light). The degradants were well-separated apart from the peaks of the active substance. The stability indicating nature was observed during the degradation. The optimized method can be applied for the separation and estimation of Upadacitinib and its process-related impurities in pharma sector in tablet dosage forms.

Asunto(s)

RESUMEN

High-energy radiation is known to potentially impact the optical performance of silicon-based sensors adversely. Nevertheless, a proper characterization and quantification of possible spectral response degradation effects due to UV stress is technically challenging. On one hand, typical illumination methods via UV lamps provide a poorly defined energy spectrum. On the other hand, a standardized measurement methodology is also missing. This work provides an approach where well-defined energy spectrum UV stress conditions are guaranteed via a customized optical set up, including a laser driven light source, a monochromator, and a non-solarizing optical fiber. The test methodology proposed here allows performing a controlled UV stress between 200 nm and 400 nm with well-defined energy conditions and offers a quantitative overview of the impact on the optical performance in CMOS-based photodiodes, along a wavelength range from 200 to 1100 nm and 1 nm step. This is of great importance for the characterization and development of new sensors with a high and stable UV spectral response, as well as for implementation of practical applications such as UV light sensing and UV-based sterilization.

RESUMEN

Solution-processed colloidal quantum dots (CQDs) are promising candidates for broadband photodetectors from visible light to shortwave infrared (SWIR). However, large-size PbS CQDs sensitive to longer SWIR are mainly exposed with nonpolar (100) facets on the surface, which lack robust passivation strategies. Herein, an innovative passivation strategy that employs planar cation, is introduced to enable face-to-face coupling on (100) facets and strengthen halide passivation on (111) facets. The defect density of CQDs film (Eg ≈ 0.74 eV) is reduced from 2.74 × 1015 to 1.04  × 1015 cm-3, coupled with 0.1 eV reduction in the activation energy of defects. The resultant CQDs photodiodes exhibit a low dark current density of 14 nA cm-2 with a high external quantum efficiency (EQE) of 62%, achieving a linear dynamic range of 98 dB, a -3dB bandwidth of 103 kHz and a detectivity of 4.7 × 1011 Jones. The comprehensive performance of the CQDs photodiodes outperforms previously reported CQDs photodiodes operating at >1.6 µm. By monolithically integrated with thin-film transistor (TFT) readout circuit, the broadband CQDs imager covering 0.35-1.8 µm realizes the functions including silicon wafer perspectivity and material discrimination, showing its potential for wide range of applications.

RESUMEN

In this study, it is demonstrated that CsPbBr3 perovskite nanocrystals (NCs) can enhance the overall performances of photomultiplication-type organic photodiodes (PM-OPDs). The proposed approach enables the ionic-polarizable CsPbBr3 NCs to be evenly distributed throughout the depletion region of Schottky junction interface, allowing the entire trapped electrons within the depletion region to be stabilized, in contrast to previously reported interface-limited strategies. The optimized CsPbBr3 -NC-embedded poly(3-hexylthiophene-diyl)-based PM-OPDs exhibit exceptionally high external quantum efficiency, specific detectivity, and gain-bandwidth product of 2,840,000%, 3.97 × 1015 Jones, and 2.14 × 107  Hz, respectively. 2D grazing-incidence X-ray diffraction analyses and drift-diffusion simulations combined with temperature-dependent J-V characteristic analyses are conducted to investigate the physics behind the success of CsPbBr3 -NC-embedded PM-OPDs. The results show that the electrostatic interactions generated by the ionic polarization of NCs effectively stabilize the trapped electrons throughout the entire volume of the photoactive layer, thereby successfully increasing the effective energy depth of the trap states and allowing efficient PM mechanisms. This study demonstrates how a hybrid-photoactive-layer approach can further enhance PM-OPD when the functionality of inorganic inclusions meets the requirements of the target device.

RESUMEN

A novel approach for developing shortwave IR (SWIR) organic photodiodes (OPDs) using doped polymers is presented. SWIR OPDs are challenging to produce because of the limitations in extending the absorption of conjugated molecules and the high dark currents of SWIR-absorbing materials. Herein, it is shown that the conversion of bound polarons to free polarons by light energy can be utilized as an SWIR photodetection mechanism. To maximize the bound-polaron density and bound-to-free polaron ratio of the doped polymer film, the doping process is engineered and dopant molecules are diffused into the crystalline domain of the polymer matrix and a direct correlation between the bound-to-free polaron ratio and device performance is confirmed. The optimized double-doped SWIR OPD exhibits a high external quantum efficiency of 77 100% and specific detectivity of 1.11 × 1011 Jones against SWIR. These findings demonstrate the application potential of polarons as alternatives for Frenkel excitons in SWIR OPDs.

RESUMEN

With the continuous advancement of nanofabrication techniques, development of novel materials, and discovery of useful manipulation mechanisms in high-performance applications, especially photodetectors, the morphology of junction devices and the way junction devices are used are fundamentally revolutionized. Simultaneously, new types of photodetectors that do not rely on any junction, providing a high signal-to-noise ratio and multidimensional modulation, have also emerged. This review outlines a unique category of material systems supporting novel junction devices for high-performance detection, namely, the van der Waals materials, and systematically discusses new trends in the development of various types of devices beyond junctions. This field is far from mature and there are numerous methods to measure and evaluate photodetectors. Therefore, it is also aimed to provide a solution from the perspective of applications in this review. Finally, based on the insight into the unique properties of the material systems and the underlying microscopic mechanisms, emerging trends in junction devices are discussed, a new morphology of photodetectors is proposed, and some potential innovative directions in the subject area are suggested.

RESUMEN

Black phosphorus (BP) has been established as a promising material for room temperature midwave infrared (MWIR) photodetectors. However, many of its attractive optoelectronic properties are often observable only at smaller film thicknesses, which inhibits photodetector absorption and performance. In this work, we show that metasurface gratings increase the absorption of BP-MoS2 heterojunction photodiodes over a broad range of wavelengths in the MWIR. We designed, fabricated, and characterized metasurface gratings that increase absorption at selected wavelengths or broad spectral ranges. We evaluated the broadband metasurfaces by measuring the room temperature responsivity and specific detectivity of BP-MoS2 photodiodes at multiple MWIR wavelengths. Our results show that broadband metasurface gratings are a scalable approach for boosting the performance of BP photodiodes over large spectral ranges.

RESUMEN

At the current stage of long-wavelength infrared (LWIR) detector technology development, the only commercially available detectors that operate at room temperature are thermal detectors. However, the efficiency of thermal detectors is modest: they exhibit a slow response time and are not very useful for multispectral detection. On the other hand, in order to reach better performance (higher detectivity, better response speed, and multispectral response), infrared (IR) photon detectors are used, requiring cryogenic cooling. This is a major obstacle to the wider use of IR technology. For this reason, significant efforts have been taken to increase the operating temperature, such as size, weight and power consumption (SWaP) reductions, resulting in lower IR system costs. Currently, efforts are aimed at developing photon-based infrared detectors, with performance being limited by background radiation noise. These requirements are formalized in the Law 19 standard for P-i-N HgCdTe photodiodes. In addition to typical semiconductor materials such as HgCdTe and type-II AIIIBV superlattices, new generations of materials (two-dimensional (2D) materials and colloidal quantum dots (CQDs)) distinguished by the physical properties required for infrared detection are being considered for future high-operating-temperature (HOT) IR devices. Based on the dark current density, responsivity and detectivity considerations, an attempt is made to determine the development of a next-gen IR photodetector in the near future.

RESUMEN

The recent emergence of non-fullerene acceptors (NFAs) has energized the field of organic photodiodes (OPDs) and made major breakthroughs in their critical photoelectric characteristics. Yet, stabilizing inverted NF-OPDs remains challenging because of the intrinsic degradation induced by improper interfaces. Herein, a tin ion-chelated polyethyleneimine ethoxylated (denoted as PEIE-Sn) is proposed as a generic cathode interfacial layer (CIL) of NF-OPDs. The chelation between tin ions and nitrogen/oxygen atoms in PEIE-Sn contributes to the interface compatibility with efficient NFAs. The PEIE-Sn can effectively endow the devices with optimized cascade alignment and reduced interface defects. Consequently, the PEIE-Sn-OPD exhibits properties of anti-environmental interference, suppressed dark current, and accelerated interfacial electron extraction and transmission. As a result, the unencapsulated PEIE-Sn-OPD delivers high specific detection and fast response speed and shows only slight attenuation in photoelectric performance after exposure to air, light, and heat. Its superior performance outperforms the incumbent typical counterparts (ZnO, SnO2 , and PEIE as the CILs) from metrics of both stability and photoelectric characteristics. This finding suggests a promising strategy for stabilizing NF-OPDs by designing appropriate interface layers.

RESUMEN

PURPOSE: Early detection of tumors and their spread, particularly in lymph node illnesses, is critical for a full recovery. However, it is currently difficult due to a lack of imaging or detection devices that provide the necessary spatial depth and location information. Consequently, it would be beneficial to have a simple and cost-effective sensor device to determine the 3D position of, e.g., a lymph node in the patient's coordinate system. METHODS: In this work, we present a concept and design for a novel semiconductor-based 3D detection system that uses inexpensive off-the-shelf components to measure gamma activity. A simple Arduino-type microcontroller calculates the 3D position of the probe based on the number of the measured pulse, the spatial sensitivity characteristics, and the known geometry of the device. RESULTS: The system was set up from four photodiodes (Osram BPW34), a transistor-based pre-amplifier, and a two-stage operational amplifier as the main stage. Doing so, a signal sufficient to be read by the microcontroller could be produced. The performed calculations proved that for a system consisting of at least four photodiodes, it is possible to determine precise location of a gamma radiation source. CONCLUSIONS: After successful first experiments with a single diode, the optimal spatial arrangement of the diodes as well as their orientation will be determined to achieve a compact, cost effective yet fast, and accurate sensor device for every-day clinical application.

RESUMEN

Engineered spectral response in photodetectors combined with advanced signal processing and deep learning-based image reconstruction enables widespread applications of hyperspectral imaging. These advancements in spectral imaging eliminate the need for complex filters and dispersion lenses, benefiting various fields such as remote sensing, astronomy, agriculture, healthcare, forensics, food quality assessment, environmental monitoring, and cultural heritage preservation. We present a spectral response design method using photon-trapping surface textures (PTSTs) to enable system miniaturization by eliminating the need for external diffraction optics and employing detector-only spectral sensors. We additionally demonstrate the fabrication of cost-effective, high-performance silicon photodetectors with unique spectral responses by integrating PTSTs. These CMOS-compatible photodetectors are ultra-fast, highly sensitive, and suitable for wideband multi/hyperspectral imaging systems. Our investigation uncovers a prominent linear correlation between the PTST periods and the peak coupling wavelengths while observing a weaker relationship with the PTST diameters. Furthermore, we establish a significant association between inter-PTST spacing and wave propagation patterns. In a proof-of-principle demonstration, we effectively employ these photodetectors with distinct spectral responses to capture visible and near-infrared wavelengths for multispectral imaging. These findings support the feasibility of integrating high-performance on-chip spectrometers, offering compact form factors, extensive applicability, and real-time data acquisition and manipulation capabilities.

RESUMEN

Healthcare systems worldwide have been stressed to provide sufficient resources to serve the increasing and aging population in our society. The situation became more challenging at the time of pandemic. Technology advancement, especially the adoption of wearable health monitoring devices, has provided an important supplement to current clinical equipment. Most health monitoring devices are rigid, however, human tissues are soft. Such a difference has prohibited intimate contact between the two and jeopardized wearing comfortableness, which hurdles measurement accuracy especially during longtime usage. Here, we report a soft and stretchable photodiode that can conformally adhere onto the human body without any pressure and measure cardiovascular variables for an extended period with higher reliability than commercial devices. The photodiode used a composite light absorber consisting of an organic bulk heterojunction embedded into an elastic polymer matrix. It is discovered that the elastic polymer matrix not only improves the morphology of the bulk heterojunction for obtaining the desired mechanical properties but also alters its electronic band structure and improves the electrical properties that lead to a reduced dark current and enhanced photovoltage in the stretchable photodiode. The work has demonstrated high fidelity measurements and longtime monitoring of heat rate variability and oxygen saturation, potentially enabling next-generation wearable photoplethysmography devices for point-of-care diagnosis of cardiovascular diseases in a more accessible and affordable way.

Asunto(s)

RESUMEN

Nowadays, optical systems play an important role in communications. Dual depletion PIN photodiodes are common devices that can operate in different optical bands, depending on the chosen semiconductors. However, since semiconductor properties vary with the surrounding conditions, some optical devices/systems can act as sensors. In this research work, a numerical model is implemented to analyze the frequency response of this kind of structure. It considers both transit time and capacitive effects, and can be applied to compute photodiode frequency response under nonuniform illumination. The InP-In0.53Ga0.47As photodiode is usually used to convert optical into electrical power at wavelengths around 1300 nm (O-band). This model is implemented considering an input frequency variation of up to 100 GHz. The focus of this research work was essentially the determination of the device's bandwidth from the computed spectra. This was performed at three different temperatures: 275 K, 300 K, and 325 K. The aim of this research work was to analyze if a InP-In0.53Ga0.47As photodiode can act as a temperature sensor, to detect temperature variations. Furthermore, the device dimensions were optimized, to obtain a temperature sensor. The optimized device, for a 6 V applied voltage and an active area of 500 µm2, had a total length of 2.536 µm, in which 53.95% corresponded to the absorption region. In these conditions, if the temperature increases 25 K from the room temperature, one should expect a bandwidth increase of 8.374 GHz, and if it decreases 25 K from that reference, the bandwidth should reduce by 3.620 GHz. This temperature sensor could be incorporated in common InP photonic integrated circuits, which are commonly used in telecommunications.

RESUMEN

Correlated oxides and related heterostructures are intriguing for developing future multifunctional devices by exploiting their exotic properties, but their integration with other materials, especially on Si-based platforms, is challenging. Here, van der Waals heterostructures of La0.7 Sr0.3 MnO3 (LSMO) , a correlated manganite perovskite, and MoS2 are demonstrated on Si substrates with multiple functions. To overcome the problems due to the incompatible growth process, technologies involving freestanding LSMO membranes and van der Waals force-mediated transfer are used to fabricate the LSMO-MoS2 heterostructures. The LSMO-MoS2 heterostructures exhibit a gate-tunable rectifying behavior, based on which metal-semiconductor field-effect transistors (MESFETs) with on-off ratios of over 104 can be achieved. The LSMO-MoS2 heterostructures can function as photodiodes displaying considerable open-circuit voltages and photocurrents. In addition, the colossal magnetoresistance of LSMO endows the LSMO-MoS2 heterostructures with an electrically tunable magnetoresponse at room temperature. This work not only proves the applicability of the LSMO-MoS2 heterostructure devices on Si-based platform but also demonstrates a paradigm to create multifunctional heterostructures from materials with disparate properties.

RESUMEN

With the growing importance of single-photon-counting (SPC) techniques, researchers are now designing high-performance systems based on single-photon avalanche diodes (SPADs). SPADs with high performances and low cost allow the popularity of SPC-based systems for medical and industrial applications. However, few efforts were put into the design optimization of SPADs due to limited calibrated models of the SPAD itself and its related circuits. This paper provides a perspective on improving SPAD-based system design by reviewing the development of SPAD models. First, important SPAD principles such as photon detection probability (PDP), dark count rate (DCR), afterpulsing probability (AP), and timing jitter (TJ) are discussed. Then a comprehensive discussion of various SPAD models focusing on each of the parameters is provided. Finally, important research challenges regarding the development of more advanced SPAD models are summarized, followed by the outlook for the future development of SPAD models and emerging SPAD modeling methods.

RESUMEN

Novel metal halide perovskite is proven to be a promising optoelectronic material. However, fabricating microscopic perovskite devices is still challenging because the perovskite is soluble with the photoresist, which conflicts with conventional microfabrication technology. The size of presently reported perovskite devices is about 50 µm. Limited by the large size of perovskite optoelectronic devices, they cannot be readily adopted in the fields of imaging, display, etc. Herein a universal microscopic patterned doping method is proposed, which can realize microscale perovskite devices. Rather than by the conventional doping method, in this study the local Fermi level of perovskite is modulated by the redistributing intrinsic ion defects via a polling voltage. A satisfactorily stable polarized ion distribution can be achieved by optimization of the perovskite material and polling voltage, resulting in ultrafast (40 µs), self-powered microscale (2 µm) photodiodes. This work sheds light on a route to fabricate integrated perovskite optoelectronic chips.

Asunto(s)