RESUMEN

BACKGROUND: The removal of adhesive remnants after bracket debonding has been shown to cause damaging effects on the enamel surface. This study aimed to investigate the efficacy of stained adhesive remnant removal (ARR) on enamel roughness compared to translucent composite. MATERIAL AND METHODS: Thirty extracted premolar teeth were divided equally into three groups; conventional composite control group (CC), stained composite group (SC) and stained bonding solution group (SB). The buccal surface of each tooth was cleaned, dried and the surface roughness (Ra) was evaluated using a contact prophylometer (T0). After bracket debonding, a high-speed carbide bur under a water-cooling system was used for ARR in one direction and the time consumed for ARR was recorded. After ARR, the second mean Ra values were recorded (T1). The samples were then polished using polishing paste with low-speed rubber cup and the third mean Ra values were recorded (T2). RESULTS: Repeated one-way ANOVA revealed a significant difference in the mean Ra values at T0, T1 and T2 within each group P˂0.05. A statistically significant difference in the changes of the mean Ra values after ARR (T1-T0) and after polishing (T1-T2) was found between the CC group and both SC and SB groups. A significant difference in the time consumed for ARR was found between the three groups with CC group being the most time-consuming group. CONCLUSION: Stained composite material followed by the stained bonding solution provided better visibility during ARR with lower mean Ra values and less time for ARR compared totranslucent composite material.

RESUMEN

The current study evaluated the bracket bond strength of hypomineralized teeth with and without acid etching. Twenty premolar teeth extracted for orthodontic purposes were used in this study. Hypomineralization was induced in all experimental teeth using a cariogenic solution. Then the teeth were divided into two groups. In the first group, orthodontic brackets were bonded by orthodontic adhesive (Green Gloo, Ormco, USA) without etching, while in the second group, further etching was used before bonding. All specimens were examined for morphological changes in the enamel surface after demineralization and debonding using a scanning electron microscope. The shear bond strength was also measured, and the recorded values of bond strengths were collected and statistically analyzed. All massed results were statistically evaluated via an independent t-test to equate Group 1 (G1) and Group 2 (G2). A p-value of < 0.05 is deemed to be statistically substantial. The shear bond strength of groups interacted by orthodontic adhesive with etching (Group 2) was considerably greater than that of groups bonded by orthodontic adhesive without etching. The etching indicates considerably greater tackiness rates compared to bonding without etching, although it leaves more destructed cores, which may need further treatment.

RESUMEN

BACKGROUND: To study and compare the effects of clear aligners without brackets and traditional fixed aligners in orthodontic treatment. METHODS: The samples were collected from January 2022 to April 2023. The control group (n = 26) received orthodontic treatment using traditional fixed appliances. The research group (n = 20) received orthodontic treatment using the clear aligners without brackets. Compare the therapeutic effects and related evaluation indicators between two groups. RESULTS: The total effective ratio was compared between the 2 groups, and the study group was greater(P < 0.05). After treatment, the detected values of the periodontal condition indicators (plaque index, debris index, and gingival bleeding index), serum inflammatory factors (CRP, IL-6 and TNF-α) of the two groups, were less than before, also were all less than the control group. (P < 0.05). After therapy, in comparison of the control group, the value of mastication efficiency, comfort and psychological evaluation, sleep indicators and the points of the four dimensions of life quality in the study group was greater, and the detection results were obviously greater than before(P < 0.05). CONCLUSION: In the orthodontic therapy of sufferers with malocclusion, compared with the traditional fixed appliance, the clear aligners without brackets can enhance the treatment effects, improve the periodontal condition and masticatory function, and reduce the inflammatory responses, so that patients can feel more comfortable, thereby improving their psychology, sleep and quality of life. In the future, with the continual advancement of technology and people's pursuit of beauty, the application of clear aligners without brackets in orthodontic treatment will become more and more extensive. The continuous introduction of new materials and new technologies will further improve the effects and comfort of the clear aligners without brackets, reduce treatment time and discomfort, and also reduce patients' resistance to aligners, bringing patients a better treatment experience.

Asunto(s)

RESUMEN

One of the biggest controversies in current orthodontics is determining the appliance to use, since today patients seek better results in shorter times, in addition to putting aesthetics first. OBJECTIVE: compare the benefits and disadvantages that arise when using fixed orthodontic appliances and transparent aligners. MATERIALS AND METHODS: An investigation and compilation of specialized bibliographic information on the topic was carried out in scientific search engines such as PubMed, SciElo and Web of Science between the years 1991 to 2023, focused on research work related to the effects of the use of orthodontic appliances. fixed compared to clear aligners. RESULTS: The review was carried out based on 53 articles found that met the selection criteria. CONCLUSION: Fixed orthodontic appliances are better in complex cases, they are more precise and less likely to relapse; Transparent aligners are more aesthetic, hygiene is more affective and the bone density of the mandibular condyle decreases.

RESUMEN

OBJECTIVE: To evaluate the effect of four different photoactivation protocols (according to "photoactivated faces" - mesial/distal, cervical/incisal or center - and "photoactivation time" - 6-3 s) of a high-power photo activator (Valo Cordless®-Ultradent) on the shear bond strength (SBS) between metal brackets and dental enamel and on the degree of conversion (DC) of an orthodontic resin. MATERIALS AND METHODS: 40 bovine incisor crowns were randomly assigned to 4 groups (n = 10). The brackets were bonded with Transbond XT® resin using 4 protocols according to the "photoactivation protocol" factor (which was subdivided into photoactivated faces and photoactivation time): V3C = 3 s + center; V6C = 6 s + center; V3M3D = 3 s on mesial + 3 s on distal; V3C3I = 3 s on cervical + 3 s on incisal. All the samples were stored for 4 months (water,37ºC) and then subjected to a SBS test (100KgF,1 mm/min). 40 resin discs were made to evaluate the monomer degree of conversion. Data from the SBS and DC were assessed by One-way ANOVA and Tukey's test (5%). Bond failures were analyzed according to the Adhesive Remnant Index (ARI) and evaluated by the Kruskal-Wallis test (5%). RESULTS: There was a statistically significant difference (p = 0.008) in the One-way ANOVA result for SBS values between all groups, but the protocols showed statistically similar results (p ≥ 0.05-Tukey's tests) concerning the photoactivated faces (V6C, V3M3D and V3C3I) and photoactivation time (V3C and V6C) factors individually. There was no statistically significant difference (p ≥ 0.05) in the One-way ANOVA result for DC values. CONCLUSION: The SBS and DC values will vary depending on the protocol applied. CLINICAL RELEVANCE: It is possible to maintain the bracket fixation quality with the use of a high-power LED photo activator associated with a shorter photoactivation time. However, it is assumed that not all types of protocols that might be applied will provide quality bonding, such as V3C, V3M3D and V3C3I, which may - depending on the SBS and DC values - affect the final treatment time, due to brackets debonding, or increase of possibility of damage to dental enamel during bracket removal. Clinical studies are suggested to confirm the hypotheses of this research.

Asunto(s)

RESUMEN

Plaque control is especially important during orthodontic treatment because areas of the teeth near brackets and wires are difficult to clean with a toothbrush, resulting in debris buildup of food or dental plaque, thus causing caries and periodontal disease. The objective of this study was to evaluate the antimicrobial properties of silver nanoparticles (AgNPs), titanium dioxide nanoparticles (TiO2NPs), and silver/titanium dioxide nanoparticles (Ag/TiO2NPs), synthesized on the surface of α-alumina ceramic brackets. The AgNPs and TiO2NPs were synthesized by a simple chemical method, and these were characterized by XRD, SEM, and XPS TEM; the antimicrobial activity was tested against Staphylococcus aureus and Escherichia coli by diffusion test. The results of this study demonstrated that by this simple chemical method, silver and titanium dioxide nanoparticles can be synthesized on the surface of α-alumina esthetic brackets, and these NPs possess good antimicrobial activity and the possibility of reducing dental caries, periodontal disease, and white spot generated during orthodontic treatment.

RESUMEN

PURPOSE: The primary objective of this study was to determine which single-shade composite surface yielded clinically acceptable shear bond strength (SBS) to metal orthodontics brackets. The secondary objectives were to identify the best composite surface treatment to enhance SBS and determine which surface treatment produced the least surface damage at debond. METHODS: Forty dental composite samples were selected from four different manufacturers (n=160) and grouped by manufacturer, one standard multi-shade dental system (FilTek™ Supreme Ultra) and three single-shade dental composites systems (OmniChroma®, SimpliShade™ and Venus® Diamond One). Each group of forty samples was randomly divided into four sub-groups (n=10). Each sub-group was identified by the surface treatment used, hydrofluoric acid (HFA), micro-etching (MIC), or phosphoric acid (PA). Shear bond strength testing and adhesive remnant index (ARI) were performed. Statistical analyses included Kruskal-Wallis, Wilcoxon rank-sum, and two-factorial ANOVA. RESULTS: OmniChroma® had statistically significant lower shear bond strength than the other composite materials tested. The control groups had statistically significant lower shear bond strength than Group 1/HFA (P<0.001) and Group 2/MIC (P<0.001). Group 1/HFA had the lowest distribution ARI score overall, while MIC had the highest ARI score distributions. CONCLUSIONS: The results of this in-vitro study found that all tested composite materials achieved clinically acceptable shear bond strengths. The utilization of micro-etching produced higher SBS. Significant Adhesive Remnant Index scores (< 0.001) were only found for OmniChroma® without any surface preparation.

Asunto(s)

RESUMEN

Introduction: One of the clinical problems following orthodontic treatment is white spot lesions around orthodontic brackets due to enamel demineralization. Confronting enamel demineralization during fixed treatments has long been a challenge for orthodontists. The aim of this in vitro study was to evaluate the effect of CO2 laser and Titanium Tetra-fluoride (TiF4) application on the prevention of enamel demineralization around orthodontic brackets. Methods: Eighty permanent premolars were selected and bonded with brackets. They were randomly divided into four groups (n=20): topical titanium tetra-fluoride gel 4% (TiF4), CO2 laser (10.6 µm wavelength for 10 seconds, peak power=291 W), fluoride+laser (F+L) and control (C). All specimens were demineralized for 10 days in a 0.2 M acetate buffer solution. The mean lesion depths were determined by using polarized light microscopy. Results: The mean depth of lesion was the highest in the C group and then decreased in the TiF4, CO2 laser, and F+L groups, respectively. The difference between all groups was significant (P<0.05), except for the CO2 laser and F+L groups. Conclusion: The lowest amount of demineralization around the orthodontic brackets was observed in the L+F group, followed by the CO2 laser, TiF4, and control groups, respectively.

RESUMEN

BACKGROUND: High precision intra-oral scans, coupled with advanced software, enable virtual bracket removal (VBR) from digital models. VBR allows the delivery of retainers and clear aligners promptly following debonding, thus reducing the patients' appointments and minimizing the likelihood of tooth movement. The objective of this study was to compare the enamel surface before bonding and after VBR using three different Computer-aided design (CAD) software and to compare their accuracy. METHODS: Maxillary scans of 20 participants starting orthodontic treatment were selected for inclusion in the study, who exhibited mild to moderate crowding and required bonding of brackets on the labial surface of permanent maxillary teeth (from the maxillary left first molar to the maxillary right first molar). Two intra-oral scans were conducted on the same day, before bonding and immediately after bonding using CEREC Omnicam (Sirona Dental Systems, Bensheim, Germany). The virtual removal of the brackets from the post-bonding models was performed using OrthoAnalyzer (3Shape, Copenhagen, Denmark), Meshmixer (Autodesk, San Rafael, Calif, USA), and EasyRx (LLC, Atlanta, GA, USA) software. The models that underwent VBR were superimposed on the pre-bonding models by Medit Link App (Medit, Seoul, South Korea) using surface-based registration. The changes in the enamel surface following VBR using the three software packages were quantified using the Medit Link App. RESULTS: There was a significant difference among the 3Shape, Meshmixer, and EasyRx software in tooth surface change following VBR. Specifically, EasyRx exhibited lower levels of accuracy compared to the other two VBR software programs (p<.001, p<.001). A significant difference in enamel surface change was observed between tooth segments across all software groups, in both incisors and molars, with VBR of the molars exhibiting the lowest level of accuracy (3Shape p=.002, Meshmixer p<.001, EasyRx p<.001). Regarding the direction of tooth surface changes following VBR, it was observed that all three groups exhibited a significant increase in the percentage of inadequate bracket removal across all teeth segments. CONCLUSIONS: 3Shape and Meshmixer manual VBR software were found to be more accurate than EasyRx automated software, however, the differences were minimal and clinically insignificant.

Asunto(s)

RESUMEN

Objectives: This study aimed to evaluate the shear bond strength of ceramic brackets bonded to the enamel surface using Vertise Flow, with or without the application of phosphoric acid. Materials and Methods: Forty-five extracted human premolar teeth were randomly assigned to three groups (N=15) based on the adhesive used for bonding: 1) Transbond XT, etch, and bond; 2) Vertise Flow; 3) Etch and Vertise Flow. After a 500-round thermocycling procedure, the shear bond strength was measured using a universal testing machine. The samples were then evaluated under a stereomicroscope to determine failure modes, and the Adhesive Remnant Index (ARI) was measured for each group. The data were analyzed with one-way ANOVA and post-hoc Tamhane at a significance level of P<0.05. Results: The highest shear bond strength values were observed in the Transbond XT (13.5±5.38MPa), acid etch and Vertise Flow (11.2±2.89MPa), and Vertise Flow (6.2±3.16MPa) groups, respectively, in descending order. The Vertise Flow group exhibited a significantly lower shear bond strength value compared to the other two groups, with no significant difference between the latter two. Conclusion: While all three study groups demonstrated clinically acceptable shear bond strength values, Vertise Flow showed lower values compared to the other two adhesives. The Vertise Flow composite resin system, whether used alone or with acid etching, remains a suitable choice for bonding ceramic brackets, offering the advantage of a simplified bonding procedure.

RESUMEN

The acidic byproducts of bacteria in plaque around orthodontic brackets contribute to white spot lesion (WSL) formation. Nitric oxide (NO) has antibacterial properties, hindering biofilm formation and inhibiting the growth of oral microbes. Materials that mimic NO release could prevent oral bacteria-related pathologies. This study aims to integrate S-nitroso-acetylpenicillamine (SNAP), a promising NO donor, into orthodontic elastomeric ligatures, apply an additional polymer coating, and evaluate the NO-release kinetics and antimicrobial activity against Streptococus mutans. SNAP was added to clear elastomeric chains (8 loops, 23 mm long) at three concentrations (50, 75, 100 mg/mL, and a control). Chains were then coated, via electrospinning, with additional polymer (Elastollan®) to aid in extending the NO release. NO flux was measured daily for 30 days. Samples with 75 mg/mL SNAP + Elastollan® were tested against S. mutans for inhibition of biofilm formation on and around the chain. SNAP was successfully integrated into ligatures at each concentration. Only the 75 mg/mL SNAP chains maintained their elasticity. After polymer coating, samples exhibited a significant burst of NO on the first day, exceeding the machine's reading capacity, which gradually decreased over 29 days. Ligatures also inhibited S. mutans growth and biofilm formation. Future research will assess their mechanical properties and cytotoxicity. This study presents a novel strategy to address white spot lesion (WSL) formation and bacterial-related pathologies by utilizing nitric oxide-releasing materials. Manufactured chains with antimicrobial properties provide a promising solution for orthodontic challenges, showing significant potential for academic-industrial collaboration and commercial viability.

Asunto(s)

RESUMEN

BACKGROUND: Recent developments in computer-aided design/computer-aided manufacturing (CAD/CAM) and 3D printing have enabled the fabrication of digital indirect bonding (IDB) transfer trays. These modern products require thorough investigation. OBJECTIVES: The aim of the study was to determine the accuracy of one-piece and three-piece IDB transfer trays in vitro. MATERIAL AND METHODS: An initial dental scan (IDS) of a randomly selected patient with digitally positioned brackets served as the master scan (MS) for designing 16 IDB transfer trays of each type. They were 3D printed and used for bonding 448 brackets to the models. Subsequently, the models were scanned with a TRIOS® 3 Intraoral Scanner (3Shape A/S, Copenhagen, Denmark), producing actual scans (ASs). The accuracy of bracket positioning was measured digitally on both MSs and ASs. The measurements were compared to the Objective Grading System for dental casts provided by the American Board of Orthodontics (ABO). RESULTS: The 2 types of IDB transfer trays showed comparable accuracy. All linear errors were within the clinically acceptable range, whereas the angular measurements demonstrated significant variability, resulting in clinically unacceptable transfer errors that ranged from 3.3% to 90.3%. CONCLUSIONS: The study results cannot be unconditionally extrapolated to other types of IDB transfer trays due to the diversity of their properties and features. The study evaluated the in vitro accuracy of IDB transfer trays. The revealed number of errors may be even higher in vivo due to limitations in visibility, salivary flow, interference from the tongue, and difficulties in achieving a proper fit of the IDB transfer tray to the teeth.

RESUMEN

Nano-coating of orthodontic brackets with a combination or hybrid of metals and metal oxides may reduce the streptococcus mutans count and incidence of enamel decalcification seen around brackets in patients undergoing fixed orthodontic treatment. In total, 255 orthodontic brackets (3M Unitek, Monrovia, California, USA) were divided into one control group (group I) of 60 and three experimental groups of 65 each (groups II, III, and IV). The experimental group brackets were coated with a combination of silver-zinc oxide, copper oxide -zinc oxide, and silver-copper oxide nanoparticles using physical vapour deposition method. The two nanoparticles used for each group were mixed in the ratio of 1:1 by weight for providing a uniform hybrid coating. Sixty brackets from each group were used for microbiological evaluation of antibacterial activity against Streptococcus mutans in blood agar medium, and the remaining five brackets from each experimental group were used for SEM analysis to check the uniformity of the coating. Nano-coated brackets demonstrated better antibacterial properties than uncoated brackets. Copper oxide-zinc oxide nanoparticles coated brackets demonstrated better antibacterial properties than the silver-zinc oxide and silver- copper oxide coated brackets.

RESUMEN

OBJECTIVES: White spot lesions are the most common iatrogenic effect observed during orthodontic treatment. This study aimed to compare the surface characteristics and antibacterial action of uncoated and coated orthodontic brackets. MATERIALS AND METHODS: Sixty commercially available stainless steel brackets were coated with TiO2 nanotubes and methacryloyloxyethylphosphorylcholine. The sample was divided into Group 1: uncoated orthodontic brackets, Group 2: Stainless steel brackets with TiO2 nanotubes coating, Group 3: Stainless steel brackets with methacryloyloxyethylphosphorylcholine coating, and Group 4: Stainless steel brackets with TiO2 nanotubes combined with methacryloyloxyethylphosphorylcholine coating. Surface characterization was assessed using atomic force microscopy and scanning electron microscopy. Streptococcus mutans was selected to test the antibacterial ability of the orthodontic brackets, total bacterial adhesion and bacterial viability were assessed. The brackets were subjected to scanning electron microscopy to detect the presence of biofilm. RESULTS: The surface roughness was the greatest in Group 1 and least in Group 2 followed by Group 4 and Group 3 coated brackets. The optical density values were highest in Group 1 and lowest in Group 4. Comparison of colony counts revealed high counts in Group 1 and low counts in Group 4. A positive correlation between surface roughness and colony counts was obtained, however, was not statistically significant. CONCLUSIONS: The coated orthodontic brackets exhibited less surface roughness than the uncoated orthodontic brackets. Group 4 coated orthodontic brackets showed the best antibacterial properties. CLINICAL RELEVANCE: Coated orthodontic brackets prevent adhesion of streptococcus mutans and reduces plaque accumulation around the brackets thereby preventing formation of white spot lesions during orthodontic treatment.

Asunto(s)

RESUMEN

OBJECTIVE: This study used a high-power light-emitting diode (LED) device to evaluate the effects of two exposure times and intensities on pulp chamber temperature and cooling time during bracket bonding. MATERIALS AND METHODS: Sixty upper premolars were used in the sample in this study. These premolars were split into two main groups based on the exposure time and intensity: the first group employed a traditional curing mode (TCG) for 20 seconds with an intensity of 1200 mw/cm2, whereas the second group had a quick curing mode (QCG) for 3 seconds with an intensity of 2500 mw/cm2. The pulp chamber's temperature variations and cooling times were recorded using a thermal imaging camera. The Mann-Whitney U test was used to find differences between the two-group comparison of the pulp chamber's temperature and cooling time. RESULTS: The two groups had statistically significant differences regarding the temperature increase in the pulp chamber and cooling time (p > 0.001). The mean temperature increase in the traditional curing group was 3.52°C, which is greater than that in the quick curing group (i.e., a mean value of 1.28°C). The mean cooling time in the traditional curing group was 38.83 seconds, which is greater than that in the quick curing group (9.97 seconds). CONCLUSIONS: Reducing the exposure time to 3 seconds and increasing the intensity to 2500 mw/cm2 is considered safer for the pulp chamber during and after the curing process.

RESUMEN

Objectives: This study aimed to explore the effects of removable aligners and fixed appliances on the supragingival bacterial communities in adult female patients undergoing orthodontic treatment. Methods: Supragingival plaque samples from 48 female individuals underwent microbiome analysis (16S rRNA gene sequencing) using PacBio Sequel sequencing. The study included 13 adults without orthodontic treatment needs as the control group (Group C), and 35 patients with comparable initial orthodontic conditions who received treatment at a university clinic in Beijing, China. The treatment involved either traditional fixed brackets (Group B, n = 17) or Invisalign® aligners (Group AT, n = 18). Bioinformatics methods were used for data analysis. Results: From the 48 plaque samples, a total of 334,961 valid reads were obtained, averaging 6,978 sequences per sample. The 16S rDNA sequences were classified into 25,727 amplicon sequence variants (ASVs). Significant variances in alpha and beta diversity among the groups were noted. Group B microbiome exhibited an increased presence of Gram-negative bacteria. At the phylum level, Actinobacteriota was significantly more prevalent in Group C samples, while Bacteroidota was enriched in Group B samples. Family-level relative abundance analysis showed a notable increase in Saccharibacteria (formerly TM7) and Prevotellaceae in Group B. Genus-level analysis revealed a significant rise in Lautropia in Group AT. Fixed orthodontic appliances were linked to oral microbiome changes, notably an enhanced relative abundance of anaerobes, including periodontal pathogens. Conclusion: The observation points to the impact of orthodontic appliance on the oral microbial community, highlighting the difference between traditional braces (Group B) and clear aligners (Group AT)in terms of the predominance of anaerobic and gram negative bacteria. This emphasizes the importance of considering the microbiological effects when choosing orthodontic appliance and underscores the need for tailored oral hygiene practices for individuals undergoing these treatments. This research might provide insights that could assist in the development of innovative cleaning techniques and antibacterial materials.

Asunto(s)

RESUMEN

Objectives: The reduction of resistance to sliding between the archwire and bracket promotes more seamless tooth movement, leading to a faster and improved orthodontic treatment experience. This research aimed to examine how the degradation of elastomeric modules, different ligation methods, bracket-wire angle, and wire type (nickel titanium, NiTi or stainless-steel, SS) impact the kinetic friction resulting from the interaction between NiTi or SS archwires and SS brackets. Materials and Methods: The current in vitro study was conducted on nine groups, including NiTi and SS archwires with three types of ligations (O-ring, figure of 8, and SS wire ligature) and two bracket-wire angles (0˚ and 10˚). The kinetic friction in each group was measured using a Universal Testing Machine at four time intervals: baseline, day one, week one, and week four. Repeated measures ANOVA, Mauchly test of sphericity followed by the Greenhouse-Geisser test, and relevant post hoc tests were used for statistical analysis (P<0.05). Results: The authors found a decrease in kinetic friction in all types of ligations, which confirmed the effect of time on the degradation of ligation modules. The kinetic friction of figure of 8 ligations was higher than both O-ring and SS wire ligations. No difference was observed between O-ring and SS wire ligations. Furthermore, the bracket-wire angle did not affect friction. Conclusion: The authors suggest that the use of figure of 8 ligations in NiTi and SS wires should be limited due to their high friction and replaced with other types of ligations, if possible.

RESUMEN

INTRODUCTION: Accurate bracket positioning remains challenging. To avoid angulation errors, some recommend examining the panoramic radiograph during bonding. However, it can cause distortions. Cone-beam computed tomography (CBCT) provides a more precise panoramic reconstruction but with higher radiation doses. The main objective of this study is to compare the accuracy of axial positioning between direct bonding without radiography, with conventional panoramic radiograph, and with panoramic reconstruction from CBCT. The secondary objectives are to evaluate positioning accuracy of each tooth and to assess the influence of practitioner level of experience. METHODS: Thirty practitioners, divided into two groups based on their experience performed direct bonding on a model thrice: without radiography, then with the conventional panoramic radiograph, then with the panoramic reconstruction from CBCT. Models were scanned, and angulation errors were measured using OrthoAnalyzer. Values were compared using the Friedman's test followed by the Bonferroni correction for multiple comparisons (P-value = 0.05). RESULTS: For the low level of experience group, angulation errors were significantly greater than the accepted limit without radiographic reference, and significantly lower with CBCT reconstruction. For the high level of experience group, angulation errors were significantly lower than the accepted limit for the three bonding methods. For every tooth, using the panoramic reconstruction from CBCT as a reference, was the most accurate method, regardless of the level of experience. More experienced practitioners made fewer errors for the three methods. CONCLUSIONS: Panoramic reconstruction from CBCT is the most accurate method to limit angulation errors during direct bonding. Conventional panoramic radiography remains a reliable tool if used with caution. Bonding without any radiographic reference should be avoided especially for less experienced practitioners.

RESUMEN

Objectives: To compare three different orthodontic adhesives (Transbond XT Light Cure Adhesive, Heliosit Orthodontic, Fuji Ortho LC) bonded to two types of orthodontic brackets: ceramic brackets (Fascination Roth 0.22) and metallic brackets (Topic Roth 0.22, Dentaurum). Materials and methods: The study was performed on 18 human teeth (6 for each adhesive). The prepared teeth were divided into three groups according to the examination time. Subsequently, they were observed after 1, 2 and 3 weeks following bonding. After the experimental procedure, the teeth samples were cut in half along the longitudinal axis in the vestibulo-oral direction, fixed with conductive carbon cement, placed in a high-vacuum evaporator and then coated with carbon. One half of each sample was observed under a Field-emission gun scanning electron microscope (FEG-SEM Hitachi SU 8030, Japan), while on the second half of the samples qualitative (X-ray line-scans) and semi-quantitative point X-ray energy dispersive analyses (EDX) were performed with Thermo Noran (USA) NSS System 7, equipped with Ultra Dry detector (30 mm2 window). Results: Transbond XT had an ideal bond with the enamel and the bracket base, with rare presence of microgaps and cracks in the enamel. Heliosit Orthodontic demonstrated a better bond relationship with the bracket base than the enamel, whereas in the latter the presence of microgaps in the bond was observed. The microphotographs of Fuji Ortho LC demonstrated many cracks inside the adhesive, and some of them continued to move forward into the enamel surface. Therefore, an impression of a very solid bond relationship with the enamel exists, with cracks being present in the enamel surface and never at the enamel-adhesive interface. Microgaps also appeared at the bracket-adhesive interface. Conclusion: Transbond XT is a highly filled composite resin and is an ideal orthodontic adhesive in each aspect examined, with an ideal enamel-adhesive and bracket-adhesive interface. Heliosit Orthodontic provides better bracket-adhesive interface compared to the enamel. Fuji Ortho LC as a solid resin-modified GIC provides a better enamel-adhesive interface, compared to the bracket base.

RESUMEN

Objective: To evaluate the progression of caries around orthodontic brackets after the enamel has been exposed to lacteal products containing probiotics. Methods: Orthodontic brackets were bonded to the enamel surfaces. The test specimens were randomly divided into six groups: G1-negative control; G2-positive control, exposed to culture environment only (without microorganisms); G3-exposed to the cariogenic environment and the fermented cow's milk without probiotic; G4-exposed to the cariogenic environment and fermented cow's milk with probiotic; G5-exposed to the cariogenic environment and yogurt without probiotic; and G6-exposed to the cariogenic environment and yogurt with probiotic. The groups were placed in brain heart infusion medium, supplemented with 2% sucrose and with 1x106 cells/ml of Streptococcus mutans and Streptococcus salivarius (ATCC). The Shapiro-Wilk, Levene, Student t, Kruskal-Wallis, and Mann-Whitney tests were used. Results: all groups exposed to the ATCC strains showed lower final microhardness, compared to the negative control (p0.05). Conclusions: Lacteal products are not able to prevent the progression of caries around orthodontic brackets.