RESUMEN
The development of polymeric biocomposites containing natural fibers has grown over the years due to the properties achieved and its eco-friendly nature. Thus, biocomposites involving a polymer from a renewable source (Biopolyethylene (BioPE)) and babassu fibers (BFs), compatibilized with polyethylene grafted with maleic anhydride (MA) and acrylic acid (AA) (PE-g-MA and PE-g-AA, respectively) were obtained using melt mixing and injection molded into tensile, impact, and HDT specimens. Babassu fiber was characterized with Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TGA), and scanning electron microscopy (SEM). The biocomposites were characterized using torque rheometry, TGA, tensile strength, impact strength, thermomechanical properties, Shore D hardness, and SEM. The data indicate that the torque during the processing of compatibilized biocomposites was higher than that of BioPE/BF biocomposites, which was taken as an indication of a possible reaction between the functional groups. Compatibilization led to a substantial improvement in the elastic modulus, tensile strength, HDT, and VST and a decrease in Shore D hardness. These results were justified with SEM micrographs, which showed babassu fibers better adhered to the surface of the biopolyethylene matrix, as well as an encapsulation of these fibers. The system investigated is environmentally sustainable, and the results are promising for the technology of polymeric composites.
RESUMEN
In this paper, the possibility of obtaining uniaxially rotomolded composite parts was discussed. The used matrix was bio-based low-density polyethylene (bioLDPE) filled with black tea waste (BTW) to prevent the thermooxidation of samples during processing. In rotational molding technology, the material is held at an elevated temperature in a molten state for a relatively long time, which can result in polymer oxidation. The Fourier transform infrared spectroscopy (FTIR) shows that adding 10 wt% of black tea waste has not led to the formation of carbonyl compounds in polyethylene, and adding 5 wt% and above prevents the appearance of the C-O stretching band connected with degradation of LDPE. The rheological analysis proved the stabilizing effect of black tea waste on the polyethylene matrix. The same temperature conditions of rotational molding did not change the chemical composition of black tea but slightly influenced the antioxidant activity of methanolic extracts; the detected changes suggest degradation is a color change, and the total color change parameter (ΔE) is 25. The oxidation level of unstabilized polyethylene measured using the carbonyl index exceeds 1.5 and gradually decreases with the addition of BTW. The BTW filler did not influence the melting properties of bioLDPE; the melting and crystallization temperature remained stable. The addition of BTW deteriorates the composite mechanical performance, including Young modulus and tensile strength, compared to the neat bioLDPE.
RESUMEN
Extrusion and hot compressing molding processes were used to create bio-polyethylene (BioPE) composites reinforced with argan byproducts (shell, pulp, and argan cake) as bio-fillers. The thermal stability of the composites wass analyzed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Dynamical mechanical analysis and rheological testing were used to investigate their mechanical properties. The morphological results showed a good adhesion between the argan and BioPE matrix. More efficient mechanical properties have been distinguished in the case of argan byproduct-based composite. A higher Young's modulus was noted for all the biocomposites compared to pure BioPE. Thermal analysis revealed that the addition of bio-filler to polymer reduced decomposition temperatures. This study provides an ecological alternative for upgrading the valorization of abundant and underutilized Moroccan biomass. Furthermore, the possibility of using argan byproducts in composite manufacturing will help open up new markets for what is currently considered waste.
RESUMEN
Rotational molding is a technology in which polymeric thin-walled products can be made. The newest descriptions of this technology concern the possibility of obtaining polymer composite materials. There are two main methods of incorporating fillers into a polymer matrix. Dry blending is based on mixing fillers with polymer powders before rotational molding by hand or using automatic mixers. In the melt compounding method, fillers are mixed with the polymer in the preliminary step by melt processing and then grinding or pulverization to obtain polymer powders for rotational molding. This work aimed to investigate the impact of the processing procedure on the structure and properties of biobased composites with expanded vermiculite. Produced rotomolded parts were examined using mechanical tests to assess changes in tensile, flexural, and impact properties. The most significant difference in mechanical properties was noted for samples with 10 wt% expanded vermiculite (EV). The elasticity modulus increases by almost 2 fold when the sample is prepared in a two-step process, the tensile strength is 4-fold higher, the flexural modulus is 3-fold higher, and the flexural strength is 5-fold higher. We also investigated thermomechanical properties in DMA measurement. The void volume content was also measured to control the quality of obtained parts. The porosity of dry blended samples containing more than 2 wt% EV is almost 2-fold higher. Other methods to control quality and structure were optical and scanning electron microscopy used for rotomolded parts and polymer powders. The investigations of rotomolded parts were supplemented with a complete description of used materials, including the particle size distributions of polymer powders and filler. Analysis of the thermal properties and chemical structure was also performed despite all the mechanical tests. The emerging conclusions from the research clearly show that the two-step process allows for achieving a more beneficial mechanical performance of the composites made of the biobased polymer in rotational molding technology.
RESUMEN
The increasing demand for petroleum-based polyethylene terephthalate (PET) grows population impacts daily. A greener and more sustainable raw material, lignocellulose, is a promising replacement of petroleum-based raw materials to convert into bio-PET. This paper reviews the recent development of lignocellulose conversion into bio-PET through bioethanol reaction pathways. This review addresses lignocellulose properties, bioethanol production processes, separation processes of bioethanol, and the production of bio-terephthalic acid and bio-polyethylene terephthalate. The article also discusses the current industries that manufacture alcohol-based raw materials for bio-PET or bio-PET products. In the future, the production of bio-PET from biomass will increase due to the scarcity of petroleum-based raw materials.
RESUMEN
The present works focuses on the development of a novel fully bio-based composite using a bio-based high-density polyethylene (Bio-HDPE) obtained from sugar cane as matrix and a by-product of extraction of chia seed oil (CO) as filler, with the objective of achieving a circular economy model. The research aims to revalorize an ever-increasing waste stream produced by the growing interest in vegetable oils. From the technical point of view, the chia seed flour (CSF) was chemically modified using a silane treatment. This treatment provides a better interfacial adhesion as was evidenced by the mechanical and thermal properties as well as field emission scanning electron microscopy (FESEM). The effect of silane treatment on water uptake and disintegration rate was also studied. On the other hand, in a second stage, an optimization of the percentage of treated CSF used as filler was carried out by a complete series of mechanical, thermal, morphological, colour, water absorption and disintegration tests with the aim to evaluate the new composite developed using chia by-products. It is noteworthy as the disintegration rate increased with the addition of CSF filler, which leads to obtain a partially biodegradable wood plastic composite (WPC) and therefore, becoming more environmentally friendly.
RESUMEN
Stiffness of material is a key parameter that allows the use of material for structural or semi-structural purposes. Besides, lightweight materials are increasingly calling the attention of the industry. Environmental impact is also increasing in its importance. Bio-based materials produced from renewable sources can be good candidates for structural purposes combining lightweight and low environmental impact. Nonetheless, similar mechanical properties of commodities have to be reached with such materials. In this work, composite materials from corn stover fibers as a bio-polyethylene reinforcement were produced and tested. The effect of coupling agents to improve the fiber-matrix interface has been evaluated. It has been found that coupling agent content influenced the stiffness of the materials, increasing the Young's modulus and the material processability. The best performance was achieved for a 6% of coupling agent, corresponding to 4.61 GPa for 50 w/w% of corn stover fibers. Micromechanics showed the impact of the semi-random orientation of the fibers and the lesser impact of its morphology. It was possible to determine a triangular packing of the composites as a hypothesis for future research.
RESUMEN
The work assumed the possibility of the introduction natural fibers as a hybrid reinforcement of bio-polyethylene composites. Coconut fibers, basalt fibers and wood flour were used in different combination as a hybrid merger. Mechanical tests were conducted. An increase in the mechanical properties was shown as an effect of the introduction of the fibers info the polymeric matrix. A synergic influence of hybrid reinforcement was also presented. Experimental results were compared with modeling parameters. The hydrothermal and accelerated thermal ageing effects on the mechanical behavior of composites were presented. Scanning electron microscope images were observed in order to analyze structure of examined composites.
RESUMEN
In recent year, there has been increasing concern about the growing amount of plastic waste coming from daily life. Different kinds of synthetic plastics are currently used for an extensive range of needs, but in order to reduce the impact of petroleum-based plastics and material waste, considerable attention has been focused on "green" plastics. In this paper, we present a broad review on the advances in the research and development of bio-based polymers analogous to petroleum-derived ones. The main interest for the development of bio-based materials is the strong public concern about waste, pollution and carbon footprint. The sustainability of those polymers, for general and specific applications, is driven by the great progress in the processing technologies that refine biomass feedstocks in order to obtain bio-based monomers that are used as building blocks. At the same time, thanks to the industrial progress, it is possible to obtain more versatile and specific chemical structures in order to synthetize polymers with ad-hoc tailored properties and functionalities, with engineering applications that include packaging but also durable and electronic goods. In particular, three types of polymers were described in this review: Bio-polyethylene (Bio-PE), bio-polypropylene (Bio-PP) and Bio-poly(ethylene terephthalate) (Bio-PET). The recent advances in their development in terms of processing technologies, product development and applications, as well as their advantages and disadvantages, are reported.
RESUMEN
The study evaluated the possibility of using natural fibers as a reinforcement of bio-polyethylene. Flax, coconut, basalt fiber, and wood flour were used in the work. Strength tests like static tensile test, three-point flexural test, or impact strength showed a positive effect of reinforcing bio-polyethylene-based composites. The effect of water and thermal ageing on the mechanical behavior of composites was assessed. In order to analyze the structure, SEM microscope images were taken and the effect of natural fibers on the change in the nature of cracking of composites was presented. Composites with natural fibers at a content of 12% by weight, resulting in increase of strength and rigidity of materials. The greatest strengthening effect for natural fibers was obtained for the composite with basalt fibers.
RESUMEN
In this article, with the aim of promoting sustainability, contributing to the circular economy and the fight against climate change, the production of composite materials from Bio-polyethylene reinforced with corn stover fibers has been studied. The behavior of the materials obtained has been studied experimentally and by mathematical models of micromechanics. The composite materials were produced by extrusion and then injection with from 10 to 50 wt.% of fibers. The creation of a good fiber-matrix interface was studied by the incorporation of coupling agent between (0-8 wt.%). Increase of 131.2% on tensile strength for 40wt.% reinforcement was achieved by adding 6 wt.% of coupling agent. The correct interface was demonstrated by a correlation of 0.99 between the experimental results and the results of the mathematical models used.
RESUMEN
The cultivation of cereals like rye, barley, oats, or wheat generates large quantities of agroforestry residues, which reaches values of around 2066 million metric tons/year. Barley straw alone represents 53%. In this work, barley straw is recommended for the production of composite materials in order to add value to this agricultural waste. First of all, thermomechanical (TMP) fibers from barley straw are produced and later used to reinforce bio-polyethylene (BioPE) matrix. TMP barley fibers were chemically and morphologically characterized. Later, composites with optimal amounts of coupling agent and fiber content ranging from 15 to 45 wt % were prepared. The mechanical results showed the strengthening and stiffening capacity of the TMP barley fibers. Finally, a micromechanical analysis is applied to evaluate the quality of the interface and to distinguish how the interface and the fiber morphology contributes to the final properties of these composite materials.
RESUMEN
The main motivation for development of biobased polymers was their biodegradability, which is becoming important due to strong public concern about waste. Reflecting recent changes in the polymer industry, the sustainability of biobased polymers allows them to be used for general and engineering applications. This expansion is driven by the remarkable progress in the processes for refining biomass feedstocks to produce biobased building blocks that allow biobased polymers to have more versatile and adaptable polymer chemical structures and to achieve target properties and functionalities. In this review, biobased polymers are categorized as those that are: (1) upgrades from biodegradable polylactides (PLA), polyhydroxyalkanoates (PHAs), and others; (2) analogous to petroleum-derived polymers such as bio-poly(ethylene terephthalate) (bio-PET); and (3) new biobased polymers such as poly(ethylene 2,5-furandicarboxylate) (PEF). The recent developments and progresses concerning biobased polymers are described, and important technical aspects of those polymers are introduced. Additionally, the recent scientific achievements regarding high-spec engineering-grade biobased polymers are presented.