RESUMEN
Dual-ion electrochemical energy storage devices have attracted much attention due to their cost effectiveness and high operating voltage. Electrochemical properties such as the specific capacity of dual-ion energy storage devices are closely related to ion migration. However, the ion migration of dual-ion energy storage devices is slow, especially the cation migration, resulting in limited discharge capacity and poor rate performance. In this study, fluorinated and nonfluorinated ambipolar conductive polymers were prepared as electrode materials. The effects of fluorination on aggregation and solvent were studied as well as its role in improving ion migration. The results show that fluorination can increase the force of fluorination on the solvent, reduce the level of binding of the solvent to the ion, and regulate the aggregation state. Compared with the unfluorinated polymer of PEPOPE, the ion migration and electrochemical kinetics of PEPFEP were significantly improved, and the PEPFPE (71 F/cm3) has a higher negative specific capacity than PEPOPE (24 F/cm3) at a current density of 5 A/cm3.
RESUMEN
As lithium-ion batteries (LIBs) become more widespread, the number of spent LIBs gradually increases. Until now, recycling of spent LIBs has mainly concentrated on high-value cathodes, but the anode graphite has not yet attracted wide attention. In this work, spent graphite from LIBs was oxidized to graphene oxide and then thermally reduced to reduced graphene oxide (RGO), which serves as the cathode of aqueous Zn dual-ion batteries (ZDIBs). The thermal reduction process enables RGO with a large layer spacing and porous structure, which increase the anion insertion sites and transfer kinetics. As a result, the corresponding battery exhibits a high specific capacity of 96.82 mAh g-1 at 1 A g-1, superior rate capability, and a high capacity retention rate of 80% after 2000 cycles. Moreover, RGO gradually transforms into a long-range disordered structure during the cycling process, which provides more transport routes and active sites for anion insertion and thus leads to the increase of capacity. This work combines the recycling of spent graphite with aqueous ZDIBs, realizing the high-value use of spent graphite.
RESUMEN
O3-type layered oxides hold significant promise as the material for cathodes in sodium-ion batteries for their favorable electrochemical properties, while irreversible structural degradation and harmful phase transitions during cyclic operation limit the practical application of these materials. In this work, we proposed a La3+/Al3+ codoping strategy in O3-Na(Ni1/3Mn1/3Fe1/3)O2 cathode materials and found that batteries with the Na (Ni1/3Mn1/3Fe1/3)0.998La0.001Al0.001O2 (NFM-La/Al) cathodes exhibited not only promoted capacity from 135.80 to 170.42 mAh g-1 at 0.2 C but also significantly enhanced cycling stability, with a 10% improvement in capacity retention compared with NFM cathodes after 300 cycles. Particularly, their rate performance was significantly improved as well. XRD and XPS tests indicated that La could expand the c-axis of NFM due to its larger ionic radius and thus significantly increased Na+ ion diffusion efficiency, and in addition, Al doping could effectively increase the content of Ni2+ and Mn4+ and thus greatly alleviated the negative Jahn-Teller effect caused by Mn3+. Moreover, consistent with XRD analyses, DFT calculations further substantiated the effectiveness of the La/Al codoping strategy by demonstrating the detailed atom substitution mechanism in the NFM crystal lattice. The boosted structure stability and Na+ diffusion kinetics may enhance the potential for practical applications of O3-type oxide cathodes.
RESUMEN
Hexagonal boron nitride (BN), a well-known member of 2D materials, has a structure similar to graphene and is often referred to as white graphene. Despite its unique physical and chemical properties for energy storage applications, there have been very few studies on how BN stores anion carriers. Herein, the hybrid architecture and anion storage mechanism of BN nanosheets for high-performance hybrid energy storage full cells based on dual-ion and Zinc (Zn) alkaline systems is demonstrated. The chemical bonding between BN and reduced graphene oxide (rGO) is attributed to the formation of the heterointerface, which facilitates the charge transfer kinetics during an OH storing process. Based on the reversible surface redox reaction of BN and rGO hybrid (BN@rGO) confirmed by computational and spectroscopic analyses, the BN@rGO electrode is applied to both Na and OH dual-ion and Zn alkaline full cells. In the dual-ion system, Ti3C2âBN@rGO full cells extended the operating voltage range up to 1.7 V, delivering a cell capacity of 49.4 mAh g-1 at 1000 mA g-1 and retaining 80% of its initial capacity after 40 000 cycles. In the Zn alkaline system, ZnâBN@rGO full cells achieved a cell capacity of 58.1 mAh g-1 at 1000 mA g-1 and retained 80% capacity over 90 000 cycles.
RESUMEN
High-voltage dual ion battery (DIB) is promising for stationary energy storage applications owing to its cost-effectiveness, which has been a hot topic of research in rechargeable battery fields. However, it still suffers from rapid battery failure caused by the severe solvent co-intercalation and electrolyte oxidation. To address these bottlenecks, herein a functional electrolyte additive hexafluoroglutaric anhydride (HFGA) is presented based on a Helmholtz plane regulation strategy. It is demonstrated that the HFGA can precisely enter into the Helmholtz plane and positively regulate anion solvation behaviors near the graphite electrode surface owing to its considerable H-F affinity with ethyl methyl carbonate (EMC), thus alleviating EMC-related co-intercalation and oxidation decomposition during DIB charging. Meanwhile, HFGA can copolymerize with the presence of PF5 at the Helmholtz plane to participate in forming a CF2-rich CEI layer with excellent PF6- permselectivity, conducive to achieving PF6- de-solvation and simultaneously suppressing electrolyte oxidation decomposition. By virtue of such beneficial effects, the graphite cathode enables a 5.5 V DIB with a prominent capacity retention of 92% and a high average Coulombic efficiency exceeding 99% within 2000 cycles, demonstrating significantly enhanced electrochemical reversibility. The Helmholtz plane regulation strategy marks a milestone in advancing DIB technologies.
RESUMEN
Na5YSi4O12 (NYSO) is demonstrated as a promising electrolyte with high ionic conductivity and low activation energy for practical use in solid Na-ion batteries. Solid-state NMR was employed to identify the six types of coordination of Na+ ions and migration pathway, which is vital to master working mechanism and enhance performance. The assignment of each sodium site is clearly determined from high-quality 23Na NMR spectra by the aid of Density Functional Theory calculation. Well-resolved 23Na exchangespectroscopy and electrochemical tracer exchange spectra provide the first experimental evidence to show the existence of ionic exchange between sodium at Na5 and Na6 sites, revealing that Na transport route is possibly along three-dimensional chain of open channel-Na4-open channel. Variable-temperature NMR relaxometry is developed to evaluate Na jump rates and self-diffusion coefficient to probe the sodium-ion dynamics in NYSO. Furthermore, NYSO works well as a dual ion conductor in Na and Li metal batteries with Na3V2(PO4)3 and LiFePO4 as cathodes, respectively.
RESUMEN
Polyanionic A3V2(PO4)3 (A = Li+, Na+) with open channels have been extensively utilized as cathode materials for aqueous zinc-metal batteries (AZMBs), whereas suffering from severe capacity fading and rapid operation voltage decay during cycling. when used as In this work, it is disclosed that the rapid degradation is induced by an irreversible phase change from electrochemical active Li3V2(PO4)3 to nonactive monoclinic LiZnPO4, as well as active Na3V2(PO4)3 to nonactive rhombic Zn3(PO4)2(H2O)4. Subsequently, a rational dual-cation (Al-Fe) doping strategy is proposed to suppress these detrimental transformations. Such dual-cation doping entails stronger P-O and V-O bonds, thus stabilizing the initial polyanionic structures. Consequently, the optimized member of Li3V1.775Al0.075Fe0.225(PO4)3 (LVAFP) exhibits desirable cycling stability (1000 cycles, 68.5% capacity retention) and notable rate capability (92.1% of the initial capacity at 10 C). Moreover, the dual-cation doping methodology is successfully extended to improve the stability of Na3V2(PO4)3 cathode in aqueous dual-ion batteries, signifying the versatility and feasibility of this strategy. The comprehensive identification of local structural evolution in these polyanions will broaden the scope of designing high-performance alkali-vanadyl-phosphates for multivalent aqueous batteries.
RESUMEN
The strong Coulombic interactions between Al3+ and traditional inorganic crystalline cathodes present a significant obstacle in developing high-performance rechargeable aluminum batteries (RABs) that hold promise for safe and sustainable stationary energy storage. While accommodating chloroaluminate ions (AlCl4 -, AlCl2+, etc.) in redox-active organic compounds offers a promising solution for RABs, the issues of dissolution and low ionic/electronic conductivities plague the development of organic cathodes. Herein, electron donors are synthetically connected with acceptors to create crosslinked, bipolar-conjugated polymer cathodes. These cathodes exhibit overlapped redox potential ranges for both donors and acceptors in highly concentrated AlCl3-based ionic liquid electrolytes. This approach strategically enables on-site doping of the polymer backbones during redox reactions involving both donor and acceptor units, thereby enhancing the electron/ion transfer kinetics within the resultant polymer cathodes. Based on the optimal donor/acceptor combination, the bipolar polymer cathodes can deliver a high specific capacity of 205 mAh g-1 by leveraging the co-storage of AlCl4 - and AlCl2+. The electrodes exhibit excellent rate performance, a stable cycle life of 60 000 cycles, and function efficiently at high mass loadings, i.e., 100 mg cm-2, and at low temperatures, i.e., -30 °C. The findings exemplify the exploration of high-performing conjugated polymer cathodes for RABs through rational structural design.
RESUMEN
The all-organic aqueous dual-ion batteries (ADIBs) have attracted increasing attention due to the low cost and high safety. However, the solubility and unstable activity of organic electrodes restrict the synergistic storage of anions and cations in the symmetric ADIBs. Herein, a novel polyimide-based covalent organic framework (labeled as NTPI-COF) is constructed, featured with the boosted structure stability and electronic conductivity. Through regulating the porosity and bipolarity integrally, the NTPI-COF possesses hierarchical porous structure (mesopore and micropore) and abundant bipolar active centers (CâO and CâN), which exhibits rapid dual-ion transport and storage effects. As a result, the NTPI-COF as the electrodes for ADIBs deliver a high reversible capacity of 109.7 mA h g-1 for Na+ storage and that of 74.8 mA h g-1 for Cl- storage at 1 A g-1, respectively, and with a capacity retention of 93.2% over 10 000 cycles at 10 A g-1. Additionally, the all-organic ADIBs with symmetric NTPI-COF electrodes achieve an impressive energy density of up to 148 W h kg-1 and a high power density of 2600 W kg-1. Coupling the bipolarity and porosity of the all-organic electrodes applied in ADIBs will further advance the development of low-cost and large-scale energy storage.
RESUMEN
Realizing high-rate and high-capacity features of Lihium-organic batteries is essential for their practical use but remains a big challenge, which is due to the instrinsic poor conductivity, limited redox kinetics and low utility of organic electrode mateials. This work presents a well-designed donor-acceptor Covalent Organic Framework (COFs) with extended conjugation, mesoscale porosity, and dual redox-active centers to promote fast charge transfer and multi-electron processes. As anticipated, the prepared cathode with benzo [1,2-b:3,4-b':5,6-b''] trithiophene (BTT) as p-type and pyrene-4,5,9,10-tetraone (PTO) as n-type material (BTT-PTO-COF) delivers impressive specific capacity (218 mAh g-1 and 275 mAh g-1 at 0.2 A g-1 in ether-based and carbonate-based electrolyte respectively) and outstanding rate capability (79 mAh g-1 at 50 A g-1 in ether-based electrolyte and 124 mAh g-1 at 10 A g-1 in carbonate-based electrolyte). Moreover, the potential of BTT-PTO-COF electrode for prototype batteries has been demonstrated by full cells of dual-ion batteries, which attain comparable electrochemical performances to the half cells. Moreover, mechanism studies combining ex-situ characterization and theoratical calculations reveal the efficient dual-ion storage process and facile charge transfer of BTT-PTO-COF. This work not only expands the diversity of redox-active COFs but also provide concept of structure design for high-rate and high-capacity organic electrodes.
RESUMEN
Designing dual-ion batteries (DIBs) by using various electrolytes through experiments or computationally is highly time-consuming and needs high-cost sophisticated resources. Here, we have utilized the ultrafast screening capability of machine learning (ML) to search for suitable salt-electrolytes toward the design of DIBs, choosing voltage as the desirable descriptor. Considering 50 different salts and their suitable staging mechanisms, the XGBoost Regressor ML model has been found to perform with remarkable accuracy. This is further validated by density functional theory, cross-validation, and experimental findings. An interpretable ML technique has been employed for local and global feature analysis to interpret the ML predicted results, underscoring the importance of choosing input features. This ML assisted DIB design approach has the potential to explore unknown salt-electrolytes that have yet to be tested in DIBs. Finally, we introduce the predicted voltages for all of the salt-electrolyte combinations as well as their probable staging mechanism. We signify the absence of a general trend in the predicted voltages, as various combinations of cations and anions are found to deliver unique voltages. Our study can guide researchers toward tuning constituent salts as well as staging mechanisms for the design of efficient DIBs.
RESUMEN
Due to the low decomposition potential of H2O and its corrosive effect to Zn foil, the Zn metal battery with aqueous electrolytes operates within a narrow electrochemical window and exhibits low anode utilization ratio. Fluorinated carbonate ester, exhibiting low highest occupied molecular orbital (HOMO) energy level, is suitable for constructing high-voltage batteries, yet its application in Zn metal battery has been scarcely explored. Herein, we propose an electrolyte based on fluorinated solvents and ethoxy (pentafluoro) cyclotriphosphazene (PFPN) additive, which exhibits a high decomposition voltage of 2.75 V in Zn batteries. The fluorinated carbonate esters possess non-flammability and exhibit reduced solvation capacity which in turn promotes the incorporation of anions into Zn2+ solvation shell. Consequently, an anion-derived interface layer is formed on Zn anode, aiding the compact and planar growth of deposited Zn. Therefore, the Zn//Zn cell exhibits an impressive Zn utilization of 91% for 140 h, a level seldom reported previously. Benefitting from the oxidation resistant solvents and cathode-electrolyte interface layer formed by PFPN additive, the Zn//graphite dual-ions battery shows an extended cycling life of 1000 cycles. Furthermore, an anode-free cell was constructed and stably operated for 100 cycles, with a notably high average discharge midpoint voltage of 1.84 V.
RESUMEN
Energy storage devices operating at low temperatures are plagued by sluggish kinetics, reduced capacity, and notorious dendritic growth. Herein, novel potassium dual-ion batteries (PDIBs) capable of superior performance at -60 °C, and fabricated by combining MXenes and polytriphenylamine (PTPAn) as the anode and cathode, respectively, are presented. Additionally, the reason for the anomalous kinetics of K+ (faster at low temperature than at room temperature) on the Ti3C2 anode is investigated. Theoretical calculations, crossover experiments, and in situ XRD at room and low temperatures revealed that K+ tends to bind with solvent molecules rather than anions at subzero temperatures, which not only inhibits the participation of PF6 - in the formation of the solid electrolyte interphase (SEI), but also guarantees co-intercalation behavior and suppresses undesirable K+ storage. The advantageous properties at low temperatures endow the Ti3C2 anode with fast K+ kinetics to unlock the outstanding performance of PDIB at ultralow temperatures. The PDIBs exhibit superior rate capability and high capacity retention at -40 °C and -60 °C. Impressively, after charging-discharging for 20,000â cycles at -60 °C, the PDIB retained 86.7 % of its initial capacity. This study reveals the influence of temperatures on MXenes and offers a unique design for dual-ion batteries operating at ultralow temperatures.
RESUMEN
Distinct from "rocking-chair" lithium-ion batteries (LIBs), the unique anionic intercalation chemistry on the cathode side of dual-ion batteries (DIBs) endows them with intrinsic advantages of low cost, high voltage, and eco-friendly, which is attracting widespread attention, and is expected to achieve the next generation of large-scale energy storage applications. Although the electrochemical reactions on the anode side of DIBs are similar to that of LIBs, in fact, to match the rapid insertion kinetics of anions on the cathode side and consider the compatibility with electrolyte system which also serves as an active material, the anode materials play a very important role, and there is an urgent demand for rational structural design and performance optimization. A review and summarization of previous studies will facilitate the exploration and optimization of DIBs in the future. Here, we summarize the development process and working mechanism of DIBs and exhaustively categorize the latest research of DIBs anode materials and their applications in different battery systems. Moreover, the structural design, reaction mechanism and electrochemical performance of anode materials are briefly discussed. Finally, the fundamental challenges, potential strategies and perspectives are also put forward. It is hoped that this review could shed some light for researchers to explore more superior anode materials and advanced systems to further promote the development of DIBs.
RESUMEN
Interfacial chemistry plays a crucial role in determining the electrochemical properties of low-temperature rechargeable batteries. Although existing interface engineering has significantly improved the capacity of rechargeable batteries operating at low temperatures, challenges such as sharp voltage drops and poor high-rate discharge capabilities continue to limit their applications in extreme environments. In this study, an energy-level-adaptive design strategy for electrolytes to regulate interfacial chemistry in low-temperature Li||graphite dual-ion batteries (DIBs) is proposed. This strategy enables the construction of robust interphases with superior ion-transfer kinetics. On the graphite cathode, the design endues the cathode interface with solvent/anion-coupled interfacial chemistry, which yields an nitrogen/phosphor/sulfur/fluorin (N/P/S/F)-containing organic-rich interphase to boost anion-transfer kinetics and maintains excellent interfacial stability. On the Li metal anode, the anion-derived interfacial chemistry promotes the formation of an inorganic-dominant LiF-rich interphase, which effectively suppresses Li dendrite growth and improves the Li plating/stripping kinetics at low temperatures. Consequently, the DIBs can operate within a wide temperature range, spanning from -40 to 45 °C. At -40 °C, the DIB exhibits exceptional performance, delivering 97.4% of its room-temperature capacity at 1 C and displaying an extraordinarily high-rate discharge capability with 62.3% capacity retention at 10 C. This study demonstrates a feasible strategy for the development of high-power and low-temperature rechargeable batteries.
RESUMEN
Well-orchestrated carbon nanostructure with superb stable framework and high surface accessibility is crucial for zinc-ion hybrid capacitors (ZIHCs). Herein, a hydrogen-bonded micelle self-assembly strategy is proposed for morphology-controllable synthesis of conjugated microporous polymers (CMPs) derived carbon to boost zinc ion storage capability. In the strategy, F127 micellar assembly through intermolecular hydrogen bonds serves as structure-directed agents, directing CMPs' oligomers grow into nanospherical assembly. The nanospherical carbon frameworks derived from CMPs (CNS-2) have shown maximized surface accessibility due to their plentiful tunable porosity and hierarchical porous structure with abundant mesoporous interconnected channels, and superb stability originating from CMPs' robust framework, thus the CNS-2-based ZIHCs exhibit ultrahigh energy density of 163 Wh kg-1 and ultralong lifespan with 93 % capacity retention after 200, 000 cycles at 20 A g-1. Charged ion storage efficiency also lies in dual-ion alternate uptake of Zn2+ and CF3SO3- as well as chemical redox of Zn2+ with carbonyl/pyridine motifs forming O-Zn-N bonds. Maximized surface accessibility and dual-ion storage mechanism ensure excellent electrochemical performance. Thus, the hydrogen-bond-guide micelle self-assembly strategy has provided a facile way to design nanoarchitectures of CMPs derived carbon for advanced cathodes of ZIHCs.
RESUMEN
Zn/alkali metal dual-ion batteries (ZM DIBs) with highly concentrated water-in-salt (WiS) electrolytes are promising next-generation energy storage systems. This enhanced design of Zn-ion rechargeable batteries offers intrinsic safety, high operating voltage, satisfactory capacity, and outstanding cyclic stability. Herein, taking the concept of highly concentrated electrolytes one step further, we introduce water-in-salt gel biopolymer electrolytes (WiS-GBEs) by encapsulating Zn/Li or Zn/Na bisalt compositions in a cellulose membrane. WiS-GBEs inherit the electrochemical merits of highly concentrated electrolytes (i.e., wide voltage window, high ionic conductivity, etc.) and excellent durability of gel biopolymer structures. Both types of WiS-GBEs apply to coin- and pouch-cell compartments of ZM DIBs, offering a high plateau voltage (>1.8 V vs. Zn2+/Zn), good and reversible capacity (118 and 57 mAh g-1 for Zn/Li and Zn/Na cells, respectively), and outstanding cycling stability (more than 90% after 1,000 cycles). Essentially, the pouch cells with WiS-GBEs present superior durability, flexibility, and capacity endurance under various bending stress conditions (90% capacity retention under 0-180° bending modes), indicating their potential capability to power wearable electronics. The practical powering ability of Li- and Na-based pouch systems is demonstrated by the example of a wearable digital timer.
RESUMEN
The development of electrochemical energy storage devices has a decisive impact on clean renewable energy. Herein, novel ultrafast rechargeable hybrid sodium dual-ion capacitors (HSDICs) were designed by using ultrathin carbon film (UCF) as the cathode material. The UCF is synthesized by a simple low temperature catalytic route followed by an acid leaching process. UCF owns a large adsorption interface and number of additional active sites, which is due to the nitrogen doping. In addition, there exists several short-range order carbons on the surface of UCF, which are beneficial for anionic storage. An ultrafast rechargeable remarkable performance, remarkable anion hybrid storage capability and outstanding structure stability is fully tapped employing UCF as cathode for HSDICs. The electrochemical performance of UCF in a half-cell system at the operating voltage between 1.0 and 4.8 V, achieving an admirable specific discharge capacity of 358.52 mAh·g-1at 500 mA·g-1, and a high capacity retention ratio of 98.42% after cycling 2500 times at 1000 mA·g-1, respectively. Besides, with the support ofex-situTEM and EDS mapping, the structural stability principle and anionic hybrid storage mechanism of UCF electrode are investigated in depth. In the full-cell system, HSDICs with the UCF as cathode and hard carbon as anode also presents a super-long cycle stability (80.62% capacity retention ratio after cycling 1300 times at 1000 mA·g-1).
RESUMEN
Dual-ion batteries (DIBs) represent a promising alternative for lithium ion batteries (LIBs) for various niche applications. DIBs with polymer-based active materials, here poly(2,2,6,6-tetramethylpiperidinyl-N-oxyl methacrylate) (PTMA), are of particular interest for high power applications, though they require appropriate electrolyte formulations. As the anion mobility plays a crucial role in transport kinetics, Li salts are varied using the well-dissociating solvent γ-butyrolactone (GBL). Lithium difluoro(oxalate)borate (LiDFOB) and lithium bis(oxalate)borate (LiBOB) improve cycle life in PTMA||Li metal cells compared to other Li salts and a LiPF6- and carbonate-based reference electrolyte, even at specific currents of 1.0â A g-1 (≈10C), whereas LiDFOB reveals a superior rate performance, i. e., ≈90 % capacity even at 5.0â A g-1 (≈50C). This is attributed to faster charge-transfer/mass transport, enhanced pseudo-capacitive contributions during the de-/insertion of the anions into the PTMA electrode and to lower overpotentials at the Li metal electrode.
RESUMEN
Most antimicrobials treat wound infections by an oxidation effect, which is induced by the generation of reactive oxygen species (ROS). However, the potential harm of the prolonged high level of ROS should not be ignored. In this study, we presented a novel cascade-reaction nanoparticle, Ir@Cu/Zn-MOF, to effectively regulate the ROS level throughout the healing progress of the infected wound. The nanoparticles consisted of a copper/zinc-modified metal-organic framework (Cu/Zn-MOF) serving as the external structure and an inner core composed of Ir-PVP NPs, which were achieved through a process known as "bionic mineralization". The released Cu2+ and Zn2+ from the shell structure contributed to the production of ROS, which acted as antimicrobial agents during the initial stage. With the disintegration of the shell, the Ir-PVP NP core was gradually released, exhibiting the property of multiple antioxidant enzyme activities, thereby playing an important role in clearing excessive ROS and alleviating oxidative stress. In a full-layer infected rat wound model, Ir@Cu/Zn-MOF nanoparticles presented exciting performance in promoting wound healing by clearing the bacteria and accelerating neovascularization as well as collagen deposition. This study provided a promising alternative for the repair of infected wounds.