RESUMEN

Purpose. To evaluate the feasibility of use of an 1.5 T magnetic resonance (MR)-linear accelerator MR-linac for imaging in gynaecologic high-dose-rate (HDR) brachytherapy.Method. Commissioning measurements for MR images quality control, geometric distortion, dwell position accuracy, applicator reconstruction and end-to-end test for a tandem-and-ring applicator were performed following the recommendations of American Brachytherapy Society, International Commission on Radiation Units and Measurements and Report of the Brachytherapy Working Group of the Spanish Society of Medical Physics. The values for MR-based IGABT were compared to the corresponding values with computed tomography (CT).Results. Measured distorsions for the MR images were less than 0.50 mm compared to the CT images. The differences between 3D displacements for all dwell positions were 0.66 mm and 0.62 mm for the tandem and ring, respectively. The maximum difference is 0.64 mm for the distances from the applicator tip obtained using the films. The CT and MR dose differences for the right and left 'A' points were 0.9% and -0.7%, respectively. Similar results were observed in terms of dose distribution for CT and Mr The gamma passing rate was 99.3% and 99.5%, respectively.Conclusion. The use of MR images from an MR-linac used in a radiotherapy service for gynaecological brachytherapy was proved to be feasible, safe and precise as the geometrical differences were less than 1 mm, and the dosimetric differences were less than 1% when comparing to the use of CT images for the same purpose.

Asunto(s)

RESUMEN

Purpose: To show the workflow for the commissioning of a MRlinac, and some proposed tests; off-axis targets, output factors for small fields, dose in inhomogeneities, and multileaf collimator quality assurance (MLC QA). Methods: The tests were performed based on TG-142, TG-119, ICRU 97, TRS-398, and TRS-483 recommendations as well as national regulations for radiation protection and safety. Results: The imaging tests are in agreement with the protocols. The radiation isocenter was 0.34 mm, and for off-axis targets location was up to 0.88 mm. The dose profiles measured and calculated in treatment planning system (TPS) passed in all cases the gamma analysis of 2%/2 mm (global dose differences). The output factors of fields larger than 2 cm × 2 cm are in agreement with the model of the MRlinac in the TPS. However, for smaller fields, their differences are higher than 10%. Picket fence test for different gantry angles showed a maximum leaf deviation up to 0.2 mm. Displacements observed in treatment couch adding weight (50 kg) are lower than 1 mm. Cryostat, bridge, and couch attenuation was up to 1.2%, 10%, and 24%, respectively. Conclusion: The implemented tests confirm that the studied MRlinac agrees with the standards reported in the literature and that the strict tolerances established as a baseline should allow a smoother implementation of stereotactic treatments in this machine.

RESUMEN

Aim: To commission and validate commercial deformable image registration (DIR) systems (SmartAdapt® and Velocity™) using task group 132 (TG-132) digital phantom datasets. Additionally, the study compares and verifies the DIR algorithms of the two systems. Materials and Methods: TG-132 digital phantoms were obtained from the American Association of Physicists in Medicine website and imported into SmartAdapt® and Velocity™ systems for commissioning and validation. The registration results were compared with known shifts using rigid registrations and deformable registrations. Virtual head and neck phantoms obtained online (DIR Evaluation Project) and some selected clinical data sets from the department were imported into the two DIR systems. For both of these datasets, DIR was carried out between the source and target images, and the contours were then propagated from the source to the target image data set. The dice similarity coefficient (DSC), mean distance to agreement (MDA), and Jacobian determinant measures were utilised to evaluate the registration results. Results: The recommended criteria for commissioning and validation of DIR system from TG-132 was error <0.5*voxel dimension (vd). Translation only registration: Both systems met TG-132 recommendations except computed tomography (CT)-positron emission tomography registration in both systems (Velocity ~1.1*vd, SmartAdapt ~1.6*vd). Translational and rotational registration: Both systems failed the criteria for all modalities (For velocity, error ranged from 0.6*vd [CT-CT registration] to 3.4*vd [CT-cone-beam CT (CBCT) registration]. For SmartAdapt® the range was 0.6*vd [CT-CBCT] to 3.6*vd [CT-CT]). Mean ± standard deviation for DSC, MDA and Jacobian metrics were used to compare the DIR results between SmartAdapt® and Velocity™. Conclusion: The DIR algorithms of SmartAdapt® and Velocity™ were commissioned and their deformation results were compared. Both systems can be used for clinical purpose. While there were only minimal differences between the two systems, Velocity™ provided lower values for parotids, bladder, rectum, and prostate (soft tissue) compared to SmartAdapt. However, for mandible, spinal cord, and femoral heads (rigid structures), both systems showed nearly identical results.

RESUMEN

In this study, we aimed to conduct a survey on the current clinical practice of, staffing for, commissioning of, and staff training for online adaptive radiotherapy (oART) in the institutions that installed commercial oART systems in Japan, and to share the information with institutions that will implement oART systems in future. A web-based questionnaire, containing 107 questions, was distributed to nine institutions in Japan. Data were collected from November to December 2023. Three institutions each with the MRIdian (ViewRay, Oakwood Village, OH, USA), Unity (Elekta AB, Stockholm, Sweden), and Ethos (Varian Medical Systems, Palo Alto, CA, USA) systems completed the questionnaire. One institution (MRIdian) had not performed oART by the response deadline. Each institution had installed only one oART system. Hypofractionation, and moderate hypofractionation or conventional fractionation were employed in the MRIdian/Unity and Ethos systems, respectively. The elapsed time for the oART process was faster with the Ethos than with the other systems. All institutions added additional staff for oART. Commissioning periods differed among the oART systems owing to provision of beam data from the vendors. Chambers used during commissioning measurements differed among the institutions. Institutional training was provided by all nine institutions. To the best of our knowledge, this was the first survey about oART performed using commercial systems in Japan. We believe that this study will provide useful information to institutions that installed, are installing, or are planning to install oART systems.

Asunto(s)

RESUMEN

Objective. The FLASH effect can potentially be used to improve the therapeutic ratio of radiotherapy (RT) through delivery of Ultra-high-dose-rate (UHDR) irradiation. Research is actively being conducted to translate UHDR-RT and for this purpose the Mobetron is capable of producing electron beams at both UHDR and conventional dose rates for FLASH research and translation. This work presents commissioning of an UHDR Mobetron with end-to-end tests developed for preclinical research.Approach. UHDR electron beams were commissioned with an efficient approach utilizing a 3D-printed water tank and film to fully characterize beam characteristics and dependences on field size, pulse width (PW) and pulse repetition frequency (PRF). This commissioning data was used to implement a beam model using the GAMOS Monte Carlo toolkit for the preclinical research. Then, the workflow for preclinical FLASH irradiation was validated with end-to-end tests delivered to a 3D-printed mouse phantom with internal inhomogeneities.Main results.PDDs, profiles and output factors acquired with radiochromic films were precisely measured, with a PRF that showed little effect on the UHDR beam energy and spatial characteristics. Increasing PW reduced theDmaxand R50by 2.08 mmµs-1and 1.28 mmµs-1respectively. An end-to-end test of the preclinical research workflow showed that both profiles in head-foot and lateral directions were in good agreement with the MC calculations for the heterogeneous 3D printed mouse phantom with Gamma index above 93% for 2 mm/2% criteria, and 99% for 3 mm/3%.Significance. The UHDR Mobetron is a versatile tool for FLASH preclinical research and this comprehensive beam model and workflow was validated to meet the requirements for conducting translational FLASH research.

Asunto(s)

RESUMEN

PURPOSE: The purpose of this work was to detail our center's experience in transitioning from a Co-60 treatment technique to an intensity modulated radiation therapy (IMRT) based lateral-field extended source-to-axis distance (e-SAD) technique for total body irradiation (TBI). MATERIALS AND METHODS: An existing beam model in RayStation v.10A was validated for the use of e-SAD TBI treatments. Data were acquired with an Elekta Synergy linear accelerator (LINAC) at an extended source-to-surface distance of 365 cm with an 18 MV beam. Beam model validation measurements included percentage depth dose (PDD), profile data, surface dose, build-up region and transmission measurements. End-to-end testing was carried out using an anthropomorphic phantom. Treatments were performed in a supine position in a whole-body Vac-Lok at an e-SAD of 400 cm with a beam spoiler 10 cm from the couch. Planning was achieved using IMRT, where multi-leaf collimators were used to modulate the beam and shield the organs at risk. Beam's eye view projection images were used for in-room patient positioning and in-vivo dosimetry was performed for every treatment. RESULTS: The percent difference between the measured and calculated PDD and profiles was less than 2% at all locations. Surface dose was 83.8% of the maximum dose with the beam spoiler at a 10 cm distance from the phantom. The largest percent difference between the treatment planning system (TPS) and measured data within the anthropomorphic phantom was approximately 2%. In-vivo dosimetry measurements yielded results within the 5% institutional threshold. CONCLUSION: In 2022, 17 patients were successfully treated using the new IMRT-based lateral-field e-SAD TBI technique. The resulting clinical plans respected the institutional standard. The commissioning process, as well as the treatment planning and delivery aspects were described in this work with the intention of supporting other clinics in implementing this treatment method.

RESUMEN

PURPOSE: To develop and characterize a large-area multi-strip ionization chamber (MSIC) for efficient measurement of proton beam spot size and position at a synchrotron-based proton therapy facility. METHODS AND MATERIALS: A 420 mm x 320 mm MSIC was designed with 240 vertical strips and 180 horizontal strips at 1.75 mm pitch. The MSIC was characterized by irradiating a grid of proton spots across 17 energies from 73.5 MeV to 235 MeV and comparing to simultaneous measurements made with a reference Gafchromic EBT3 film. Beam profiles, spot sizes, and positions were analyzed. Short term measurement stability and sensitivity were evaluated. RESULTS: Excellent agreement was demonstrated between the MSIC and EBT3 film for both spot size and position measurements. Spot sizes agreed within ± 0.18 mm for all energies tested. Measured beam spot positions agreed within ± 0.17 mm. The detector showed good short term measurement stability and low noise performance. CONCLUSION: The large-area MSIC enables efficient and accurate proton beam spot characterization across the clinical energy range. The results indicate the MSIC is suitable for pencil beam scanning proton therapy commissioning and quality assurance applications requiring fast spot size and position quantification.

Asunto(s)

RESUMEN

IMPACT: This article suggests why a different approach may be required for commissioning services from third sector providers than from, say, corporate or public providers. English systems for commissioning third sector providers contain both commodified elements (for example formal procurement, provider competition, commissioner-provider separation) and collaborative, relational elements (for example long-term collaboration, reliance on inter-organizational networks). When the two elements conflicted, commissioners and third sector organizations tended to try to work around the commodified elements in order to preserve and develop the collaborative aspects, which suggests that, in practice, they find de-commodified, collaborative methods better adapted to the commissioning of third sector organizations. ABSTRACT: When publicly-funded services are outsourced, governments still use multiple governance structures to retain some control over the services provided. Using realist methods the authors systematically compared this aspect of community health activities provided by third sector organizations in six English localities during 2020-2022. Two modes of commissioning coexisted. Commodified commissioning largely embodied Washington consensus models of formal, competitive procurement. A contrasting, collaborative mode of commissioning relied more upon relational, long-term co-operation and networking among organizations. When the two modes conflicted, commissioners often favoured the collaborative mode and sought to adjust their commissioning to make it less commodified.

RESUMEN

Background & Purpose: FLASH or ultra-high dose rate (UHDR) radiation therapy (RT) has gained attention in recent years for its ability to spare normal tissues relative to conventional dose rate (CDR) RT in various preclinical trials. However, clinical implementation of this promising treatment option has been limited because of the lack of availability of accelerators capable of delivering UHDR RT. Commercial options are finally reaching the market that produce electron beams with average dose rates of up to 1000 Gy/s. We established a framework for the acceptance, commissioning, and periodic quality assurance (QA) of electron FLASH units and present an example of commissioning. Methods: A protocol for acceptance, commissioning, and QA of UHDR linear accelerators was established by combining and adapting standards and professional recommendations for standard linear accelerators based on the experience with UHDR at four clinical centers that use different UHDR devices. Non-standard dosimetric beam parameters considered included pulse width, pulse repetition frequency, dose per pulse, and instantaneous dose rate, together with recommendations on how to acquire these measurements. Results: The 6- and 9-MeV beams of an UHDR electron device were commissioned by using this developed protocol. Measurements were acquired with a combination of ion chambers, beam current transformers (BCTs), and dose-rate-independent passive dosimeters. The unit was calibrated according to the concept of redundant dosimetry using a reference setup. Conclusions: This study provides detailed recommendations for the acceptance testing, commissioning, and routine QA of low-energy electron UHDR linear accelerators. The proposed framework is not limited to any specific unit, making it applicable to all existing eFLASH units in the market. Through practical insights and theoretical discourse, this document establishes a benchmark for the commissioning of UHDR devices for clinical use.

RESUMEN

PURPOSE: The purpose of this study was to validate the use of a model-based dose calculation algorithm (MBDCA), Acuros BV, for high dose rate brachytherapy treatment planning for a community-based hospital with a Bravos afterloader. Based on published AAPM recommendations, this work details a practical approach for community-based clinics to complete initial validation of Acuros BV, in order to add a MBDCA to a TG-43 based brachytherapy treatment planning program. METHODS: Source dimensions and materials used in Acuros BV and TG-43 source models were compared to the physical source. TG-186 testing was completed with standardized test cases externally calculated with Monte Carlo compared to locally calculated with Acuros BV. Point doses calculated using TG-43 were compared to those calculated with Acuros BV in water at various dose grid settings. Secondary dose check software was used to evaluate dose distributions resembling clinical patient plans, both in water and on CT datasets representative of patient anatomy. RESULTS: The major source of discrepancy of source models was the length of modeled steel cable. TG-186 testing showed that the largest differences between Monte Carlo and Acuros BV dose distributions were located along the source axis for cases calculated in water, as well as located in regions of high dose gradients and within the applicator for the case calculated with a generic shielded applicator. An audit of point doses calculated with both TG-43 and Acuros BV in water found that dose grid settings significantly affected agreement. Secondary dose check software indicated that Acuros BV functioned satisfactorily, and a 5% threshold was adopted for secondary dose checks on gynecologic plans. CONCLUSION: This validation process indicated that Acuros BV met expected standards and affirmed its suitability for integration into this clinical practice's brachytherapy treatment planning.

Asunto(s)

RESUMEN

INTRODUCTION: This exploratory literature review seeks to examine the literature around commissioning processes in the co-production of health and care services, focusing on two questions: How do health and care commissioning processes facilitate and/or pose barriers to co-production in service design and delivery? What are the contextual factors that influence these processes? METHOD: A systematic search of three databases (Medline, Public Health and Social Policy and Practice) and a search platform (Web of Science) was conducted for the period 2008-2023. A total of 2675 records were retrieved. After deduplication, 1925 were screened at title and abstract level. Forty-seven reports from 42 United Kingdom and Ireland studies were included in the review. A thematic synthesis of included studies was conducted in relation to the research questions. RESULTS: The review identified one overarching theme across the synthesised literature: the complexity of the commissioning landscape. Three interconnected subthemes illuminate the contextual factors that influence this landscape: commissioners as leaders of co-production; navigating relationships and the collective voice. CONCLUSION: Commissioning processes were commonly a barrier to the co-production of health and care services. Though co-production was an aspiration for many commissioners, the political and economic environment and service pressures meant that it was often not fully realised. More flexible funding models, longer-term pilot projects, an increased emphasis in social value across the health and care system and building capacity for strong leadership in commissioning is needed. PATIENT AND PUBLIC CONTRIBUTION: Patients and the public did not contribute to this review as it was a small piece of work following on from a completed project, with no budget for public involvement.

Asunto(s)

RESUMEN

Purpose: We performed computed tomography (CT)-stopping power ratio (SPR) calibration in a carbon-ion therapy facility and evaluated SPR estimation accuracy. Materials and Methods: A polybinary tissue model method was used for the calibration of CT numbers and SPR. As a verification by dose calculation, we created a virtual phantom to which the CT-SPR calibration table was applied. Then, SPR was calculated from the change in the range of the treatment planning beam when changing to 19 different CT numbers, and the accuracy of the treatment planning system (TPS) calculation of SPR values from the CT-SPR calibration table was validated. As a verification by measurement, 5 materials (water, milk, olive oil, ethanol, 40% K2HPO4) were placed in a container, and the SPR was obtained by measurement from the change in the range of the beam that passed through the materials. Results: The results of the dose calculations of the TPS showed that the results agreed within 1% for the lower CT numbers up to 1000 HU, but there was a difference of 3.0% in the higher CT number volume. The difference between the SPR calculated by TPS and the SPR caused by the difference in the energy of the incident particles agreed within 0.51%. The accuracy of SPR estimation was measured, and the error was within 2% for all materials tested. Conclusion: These results indicate that the SPR estimation errors are within the range of errors that can be expected in particle therapy. From commissioning and verification results, the CT-SPR calibration table obtained during this commissioning process is clinically applicable.

RESUMEN

PURPOSE: A novel pulse normalization technology enabling the acquisition of low noise beam data without the use of a physical reference chamber has recently been commercially released. The purpose of this study was to characterize the use of this technology for beam scanning of small fields required in the commissioning of a stereotactic radiotherapy program. METHODS: Three detectors (Edge diode, microDiamond, PinPoint) were used to acquire beam data under three conditions: with a reference chamber, with pulse normalization and no reference chamber (PN), and without pulse normalization and no reference chamber (nPN). Percent depth dose (PDD) scans were acquired for 0.5, 1.0, 2.0, and 3.0 cm2 field sizes and profiles were acquired at 1.4, 10, and 30 cm depths using continuous scanning. The coefficient of variation (CoV) was calculated for all beam data to compare signal-to-noise and gamma comparisons (1%, 1 mm) were calculated of the PN and nPN scans compared to the reference data. RESULTS: Average 95th percentile CoV values were similar for all detectors across conditions, with PN data being comparable to reference data and minor increases observed for nPN data. Mean gamma pass rates for PN PDD scans exceeded 98% for all detectors. Profile gamma pass rates were 100% for all detectors at 1.4 and 10 cm depth. At 30 cm depth, profiles acquired with the PinPoint and microDiamond detectors had lower mean gamma pass rates than the Edge, at 95% and 95.7%, respectively. CONCLUSIONS: A novel pulse normalization technology was demonstrated to be effective for acquiring beam profiles and PDDs for small fields without the use of a physical reference chamber. Limitations in how the method is implemented led to some errors in data acquired using lower sensitivity detectors. When used with a diode, pulse normalization produced equivalent scans to those acquired with a reference chamber.

Asunto(s)

RESUMEN

BACKGROUND: Despite several interventions demonstrating benefit to people living with dementia and their caregivers, few have been translated and implemented in routine clinical practice. There is limited evidence of the barriers and facilitators for commissioning and implementing health and social care interventions for people living with dementia. The aim of the current study was to explore the barriers and facilitators to commissioning and implementing health and social care interventions for people with dementia, using a dementia friendly exercise and physical activity-based intervention (PrAISED [Promoting Activity, Stability and Independence in Early Dementia and Mild Cognitive Impairment]) as a case study. METHODS: Qualitative semi-structured interviews were conducted with stakeholders from a range of backgrounds including individuals from health and social care, local government, the voluntary and community sector, universities, and research centres in England. The Consolidated Framework for Intervention Research (CFIR) was used to guide the design and analysis. RESULTS: Fourteen participants took part, including commissioning managers, service managers, partnership managers, charity representatives, commercial research specialists, academics/researchers, and healthcare professionals. Data were represented in 33 constructs across the five CFIR domains. Participants identified a need for greater support for people diagnosed with dementia and their caregivers immediately post dementia diagnosis. Key barriers included cost/financing, the culture of commissioning, and available resources. Key facilitators included the adaptability of the intervention, cosmopolitanism/partnerships and connections, external policy and incentives, and the use of already existing (and untapped) workforces. CONCLUSION: Several barriers and facilitators for commissioning and implementing health and social care interventions for people with dementia were identified which need to be addressed. Recommended actions to facilitate the commissioning and implementation of dementia friendly services are: 1) map out local needs, 2) evidence the intervention including effectiveness and cost-effectiveness, 3) create/utilise networks with stakeholders, and 4) plan required resources.

RESUMEN

BACKGROUND: Social and Therapeutic Horticulture (STH) is a process where trained practitioners work with plants and people to improve an individual's physical and psychological health, communication and thinking skills. Evidence suggests that STH can support individuals with mental ill-health, however, current commissioning of STH within mental health care is limited. This study aimed to understand the barriers to commissioning STH in mental health care and to identify potential solutions to barriers, to support more widespread availability of services.  METHODS: Individuals with a role in mental health care commissioning from across the UK were invited to take part in semi-structured interviews via zoom. Interviews explored factors influencing the mental health services they commission or refer to, their perception of the role of STH in mental health care and the barriers to commissioning STH, together with potential solutions to any barriers identified. RESULTS: Commissioners identified a lack of knowledge of STH and evidence of its effectiveness, and a culture which prioritises traditional medical models, as barriers to commissioning. Challenges for STH providers in responding to large-scale commissioning requirements were also highlighted as a barrier. CONCLUSIONS: To upscale commissioning of STH in mental health care, STH interventions need to be embedded within NHS priorities and information on STH services and their effectiveness needs to be easily accessible to practitioners. The sector should also be supported in working collaboratively to enable commissioning of services at scale.

Asunto(s)

RESUMEN

BACKGROUND: Weight management services have not always benefitted everyone equally. People who live in more deprived areas, racially minoritised communities, those with complex additional needs (e.g., a physical or mental disability), and men are less likely to take part in weight management services. This can subsequently widen health inequalities. One way to counter this is to co-design services with under-served groups to better meet their needs. Using a case study approach, we explored how co-designed adult weight management services were developed, the barriers and facilitators to co-design, and the implications for future commissioning. METHODS: We selected four case studies of adult weight management services in Southwest England where co-design had been planned, representing a range of populations and settings. In each case, we recruited commissioners and providers of the services, and where possible, community members involved in co-design activities. Interviews were conducted online, audio-recorded, transcribed verbatim, and analysed using thematic analysis. RESULTS: We interviewed 18 participants (8 female; 10 male): seven commissioners, eight providers, and three community members involved in co-designing the services. The case studies used a range of co-design activities (planned and actualised), from light-touch to more in-depth approaches. In two case studies, co-design activities were planned but were not fully implemented due to organisational time or funding constraints. Co-design was viewed positively by participants as a way of creating more appropriate services and better engagement, thus potentially leading to reduced inequalities. Building relationships- with communities, individual community members, and with partner organisations- was critical for successful co-design and took time and effort. Short-term and unpredictable funding often hindered co-design efforts and could damage relationships with communities. Some commissioners raised concerns over the limited evidence for co-design, while others described having to embrace "a different way of thinking" when commissioning for co-design. CONCLUSIONS: Co-design is an increasingly popular approach to designing health in services but can be difficult to achieve within traditional funding and commissioning practices. Drawing on our case studies, we present key considerations for those wanting to co-design health services, noting the importance of building strong relationships, creating supportive organisational cultures, and developing the evidence base.

Asunto(s)

RESUMEN

PURPOSE: To assess a large panel of MR compatible detectors on the full range of measurements required for a 0.35 T MR-linac commissioning by using a specific statistical method represented as a continuum of comparison with the Monte Carlo (MC) TPS calculations. This study also describes the commissioning tests and the secondary MC dose calculation validation. MATERIAL AND METHODS: Plans were created on the Viewray TPS to generate MC reference data. Absolute dose points, PDD, profiles and output factors were extracted and compared to measurements performed with ten different detectors: PTW 31010, 31021, 31022, Markus 34045 and Exradin A28 MR ionization chambers, SN Edge shielded diode, PTW 60019 microdiamond, PTW 60023 unshielded diode, EBT3 radiochromic films and LiF µcubes. Three commissioning steps consisted in comparison between calculated and measured dose: the beam model validation, the output calibration verification in four different phantoms and the commissioning tests recommended by the IAEA-TECDOC-1583. MAIN RESULTS: The symmetry for the high resolution detectors was higher than the TPS data of about 1%. The angular responses of the PTW 60023 and the SN Edge were - 6.6 and - 11.9% compared to the PTW 31010 at 60°. The X/Y-left and the Y-right penumbras measured by the high resolution detectors were in good agreement with the TPS values except for the PTW 60023 for large field sizes. For the 0.84 × 0.83 cm2 field size, the mean deviation to the TPS of the uncorrected OF was - 1.7 ± 1.6% against - 4.0 ± 0.6% for the corrected OF whereas we found - 4.8 ± 0.8% for passive dosimeters. The mean absolute dose deviations to the TPS in different phantoms were 0 ± 0.4%, - 1.2 ± 0.6% and 0.5 ± 1.1% for the PTW 31010, PTW 31021 and Exradin A28 MR respectively. CONCLUSIONS: The magnetic field effects on the measurements are considerably reduced at low magnetic field. The PTW 31010 ionization chamber can be used with confidence in different phantoms for commissioning and QA tests requiring absolute dose verifications. For relative measurements, the PTW 60019 presented the best agreement for the full range of field size. For the profile assessment, shielded diodes had a behaviour similar to the PTW 60019 and 60023 while the ionization chambers were the most suitable detectors for the symmetry. The output correction factors published by the IAEA TRS 483 seem to be applicable at low magnetic field pending the publication of new MR specific values.

Asunto(s)

RESUMEN

The purpose of this study was to validate an electronic portal imaging device (EPID) based 3-dimensional (3D) dosimetry system for the commissioning of volumetric modulated arc therapy (VMAT) delivery for flattening filter (FF) and flattening filter free (FFF) modalities based on test suites developed according to American Association of Physicists in Medicine Task Group 119 (AAPM TG 119) and pre-treatment patient specific quality assurance (PSQA).With ionisation chamber, multiple-point measurement in various planes becomes extremely difficult and time-consuming, necessitating repeated exposure of the plan. The average agreement between measured and planned doses for TG plans is recommended to be within 3%, and both the ionisation chamber and PerFRACTION™ measurement were well within this prescribed limit. Both point dose differences with the planned dose and gamma passing rates are comparable with TG reported multi-institution results. From our study, we found that no significant differences were found between FF and FFF beams for measurements using PerFRACTION™ and ion chamber. Overall, PerFRACTION™ produces acceptable results to be used for commissioning and validating VMAT and for performing PSQA. The findings support the feasibility of integrating PerFRACTION™ into routine quality assurance procedures for VMAT delivery. Further multi-institutional studies are recommended to establish global baseline values and enhance the understanding of PerFRACTION™'s capabilities in diverse clinical settings.

Asunto(s)

RESUMEN

The specialist voluntary sector plays a crucial role in supporting survivors of sexual violence. However, in England, short-term funding underpins the sector's financial stability. This article examines sector leaders' ways of coping, resisting and being affected by funding practices. Using the concept of edgework, we show how funding and commissioning dynamics push individuals to the edge of service sustainability, job satisfaction, and emotional well-being. We examine how these edges are "worked," for example, by circumventing and remolding the edge. We offer an original way to theorize participants, make visible the emotional toll of service precarity and offer suggestions for support.

RESUMEN

PURPOSE: Experimental patient-specific QA (PSQA) is a time and resource-intensive process, with a poor sensitivity in detecting errors. Radiation therapy facilities aim to substitute it by means of independent dose calculation (IDC) in combination with a comprehensive beam delivery QA program. This paper reports on the commissioning of the IDC software tool myQA iON (IBA Dosimetry) for proton therapy and its clinical implementation at the MedAustron Ion Therapy Center. METHODS: The IDC commissioning work included the validation of the beam model, the implementation and validation of clinical CT protocols, and the evaluation of patient treatment data. Dose difference maps, gamma index distributions, and pass rates (GPR) have been reviewed. The performance of the IDC tool has been assessed and clinical workflows, simulation settings, and GPR tolerances have been defined. RESULTS: Beam model validation showed agreement of ranges within ± 0.2 mm, Bragg-Peak widths within ± 0.1 mm, and spot sizes at various air gaps within ± 5% compared to physical measurements. Simulated dose in 2D reference fields deviated by -0.3% ± 0.5%, while 3D dose distributions differed by 1.8% on average to measurements. Validation of the CT calibration resulted in systematic differences of 2.0% between IDC and experimental data for tissue like samples. GPRs of 99.4 ± 0.6% were found for head, head and neck, and pediatric CT protocols on a 2%/2 mm gamma criterion. GPRs for the adult abdomen protocol were at 98.9% on average with 3%/3 mm. Root causes of GPR outliers, for example, implants were identified and evaluated. CONCLUSION: IDC has been successfully commissioned and integrated into the MedAustron clinical workflow for protons in 2021. IDC has been stepwise and safely substituting experimental PSQA since February 2021. The initial reduction of proton experimental PSQA was about 25% and reached up to 90% after 1 year.

Asunto(s)