RESUMEN

The transition to sustainable materials and eco-efficient processes in commercial electronics is a driving force in developing green electronics. Iron-catalyzed laser-induced graphitization (IC-LIG) has been demonstrated as a promising approach for rendering biomaterials electrically conductive. To optimize the IC-LIG process and fully exploit its potential for future green electronics, it is crucial to gain deeper insights into its catalyzation mechanism and structural evolution. However, this is challenging due to the rapid nature of the laser-induced graphitization process. Therefore, multiscale preparation techniques, including ultramicrotomy of the cross-sectional transition zone from precursor to fully graphitized IC-LIG electrode, are employed to virtually freeze the IC-LIG process in time. Complementary characterization is performed to generate a 3D model that integrates nanoscale findings within a mesoscopic framework. This enabled tracing the growth and migration behavior of catalytic iron nanoparticles and their role during the catalytic laser-graphitization process. A three-layered arrangement of the IC-LIG electrode is identified including a highly graphitized top layer with an interplanar spacing of 0.343 nm. The middle layer contained γ-iron nanoparticles encapsulated in graphitic shells. A comparison with catalyst-free laser graphitization approaches highlights the unique opportunities that IC-LIG offers and discuss potential applications in energy storage devices, catalysts, sensors, and beyond.

RESUMEN

Vanadium-based metallic salts, characterized by their intrinsic low electronic conductivity, are impeding their advancement as anode materials in the realm of lithium-ion battery technology. This study presents a novel embedded anode material KVO3/NC (KVO/NC) synthesized via a sol-gel method, with KVO3 (KVO) particles in situ growing on N-doped carbon, thereby ameliorating conductivity and electrochemical performance. The findings reveal that KVO/NC composite has three lithium-ion storage sites, ultra-high cycling stability (289 mA h/g@5000 cycles@10 C@100 %), and superior rate performance (249 mA h/g@15 C; 221 mA h/g@20 C). Coupled with LiFePO4 cathode, it achieves a competitive energy density (391 W h kg-1@0.1 C; 1-3.9 V). This work reveals the practical potential of KVO/NC as a new type of lithium-ion battery anode material with high energy density and long cycle life through a series of ex situ/in situ characterizations.

RESUMEN

Extensive studies have been conducted on deicing nanomaterials to improve the cryoprotective effects on cells, tissues, and organs. The nanomaterials with different composition, sizes, and shapes can inhibit the formation and growth of ice crystals, thereby reducing the damage to the cryopreserved samples. In this study, the carbon composite particles (CCPs) with different sizes and shapes were prepared by the hydrothermal method. The results demonstrated that the cryoprotective effect of CCPs enhanced with the decrease in particle size. Compared with spherical CCPs, Janus nanoparticles and WSP nanoflower with special shapes demonstrated improved protective effects on cryopreserved cells. In addition, the combination of deicing micro/nanomaterials at appropriate concentrations with commercial cryoprotectants exerted improved cryoprotective effects on cells. The prepared deicing micro/nanomaterials can improve cell cryopreservation, demonstrating great application potential in biomedical research and cryopreservation.

Asunto(s)

RESUMEN

Silicon (Si) shows great potential as an anode material for lithium-ion batteries. However, it experiences significant expansion in volume as it undergoes the charging and discharging cycles, presenting challenges for practical implementation. Nanostructured Si has emerged as a viable solution to address these challenges. However, it requires a complex preparation process and high costs. In order to explore the above problems, this study devised an innovative approach to create Si/C composite anodes: micron-porous silicon (p-Si) was synthesized at low cost at a lower silver ion concentration, and then porous silicon-coated carbon (p-Si@C) composites were prepared by compositing nanohollow carbon spheres with porous silicon, which had good electrochemical properties. The initial coulombic efficiency of the composite was 76.51%. After undergoing 250 cycles at a current density of 0.2 A·g-1, the composites exhibited a capacity of 1008.84 mAh·g-1. Even when subjected to a current density of 1 A·g-1, the composites sustained a discharge capacity of 485.93 mAh·g-1 even after completing 1000 cycles. The employment of micron-structured p-Si improves cycling stability, which is primarily due to the porous space it provides. This porous structure helps alleviate the mechanical stress caused by volume expansion and prevents Si particles from detaching from the electrodes. The increased surface area facilitates a longer pathway for lithium-ion transport, thereby encouraging a more even distribution of lithium ions and mitigating the localized expansion of Si particles during cycling. Additionally, when Si particles expand, the hollow carbon nanospheres are capable of absorbing the resulting stress, thus preventing the electrode from cracking. The as-prepared p-Si utilizing metal-assisted chemical etching holds promising prospects as an anode material for lithium-ion batteries.

RESUMEN

A composite material of tungsten carbide and mesoporous carbon was synthesized by the sol-gel polycondensation of resorcinol and formaldehyde, using cetyltrimethylammonium bromide as a surfactant and Ludox HS-40 as a porogen, and served as a support for Pd-based electrodes. Phosphorus-modified Pd particles were deposited onto the support using an NH3-mediated polyol reduction method facilitated by sodium hypophosphite. Remarkably small Pd nanoparticles with a diameter of ca. 4 nm were formed by the phosphorus modification. Owing to the high dispersion of Pd and its strong interaction with tungsten carbide, the Pd nanoparticles embedded in the tungsten carbide/mesoporous carbon composite exhibited a hydrogen oxidation activity approximately twice as high as that of the commercial Pt/C catalyst under the anode reaction conditions of proton exchange membrane fuel cells.

RESUMEN

Due to safety problems caused by the use of organic electrolytes in lithium-ion batteries and the high production cost brought by the limited lithium resources, water-based zinc-ion batteries have become a new research focus in the field of energy storage due to their low production cost, safety, efficiency, and environmental friendliness. This paper focused on vanadium dioxide and expanded graphite (EG) composite cathode materials. Given the cycling problem caused by the structural fragility of vanadium dioxide in zinc-ion batteries, the feasibility of preparing a new composite material is explored. The EG/VO2 composites were prepared by a simple hydrothermal method, and compared with the aqueous zinc-ion batteries assembled with a single type of VO2 under the same conditions, the electrode materials composited with high-purity sulfur-free expanded graphite showed more excellent capacity, cycling performance, and multiplicity performance, and the EG/VO2 composites possessed a high discharge ratio of 345 mAh g-1 at 0.1 A g-1, and the Coulombic efficiency was close to 100%. The EG/VO2 composite has a high specific discharge capacity of 345 mAh g-1 at 0.1 A g-1 with a Coulombic efficiency close to 100%, a capacity retention of 77% after 100 cycles, and 277.8 mAh g-1 with a capacity retention of 78% at a 20-fold increase in current density. The long cycle test data demonstrated that the composite with expanded graphite effectively improved the cycling performance of vanadium-based materials, and the composite maintained a stable Coulombic efficiency of 100% at a high current density of 2 A/g and still maintained a specific capacity of 108.9 mAh/g after 2000 cycles.

RESUMEN

This research is aimed at studying the properties of polymer anticorrosion coatings based on ED-20 resin widely used in practice and industrial wastes. In this work, three basic types of nanoscale nanofillers were chosen: dispersed particles-microsilica, microspheres obtained at Kazakh enterprises, and carbon nanotubes. Physicochemical research methods were used in the research: a laser analyzer for studying the dispersibility of industrial waste and spectrometric research methods. The properties of materials were investigated by standardized methods. The obtained results show that the introduction of microsilica and microspheres obtained at Kazakhstani enterprises, used as additives, improves both the physical and mechanical properties of epoxy composites compared to the standard (control) material. The results of experiments have shown that the optimal content of additives of microsilica and microspheres provides an improvement in the physical and mechanical properties of epoxy composites in comparison with the standard (control) material. Studies have shown that the introduction of microspheres into ED-20 polymer increases impact toughness. The introduction of microsilica into the matrix contributes to the increase of elastic modulus. Experimental studies of optical properties of samples of carbon composite polymer films based on polystyrene (PS) with additives of carbon nanotubes C60 and C70 and multilayer carbon nanotubes were also carried out. The experimental results obtained for the optical properties of polymer composites based on basic polymers from solid waste and carbon nanotubes showed that the optical properties of polymer composites undergo noticeable changes.

RESUMEN

Sn and C nanocomposites are ideal anode materials for high-energy and high-power density lithium ion batteries. However, their facile and controllable synthesis for practical applications is still a critical challenge. In this work, a facile one-step method is developed to controllably synthesize ultrafine Sn nanocrystals (< 5 nm) loaded on carbon black (Sn@C) through Na reducing SnCl4 by mechanical milling. Different from traditional up-down mechanical milling method, this method utilizes mechanical milling to trigger bottom-up reduction reaction of SnCl4. The in-situ formed Sn nanocrystals directly grow on carbon black, which results in the homogeneous composite and the size control of Sn nanocrystals. The obtained Sn@C electrode is revealed to possesses large lithium diffusion coefficient, low lithiation energy barrier and stable electrochemical property during cycle, thus showing excellent lithium storage performance with a high reversible capacity (942 mAh g-1 at a current density of 100 mA g-1), distinguished rate ability (480 mAh g-1 at 8000 mA g-1) and superb cycling performance (730 mAh g-1 at 1000 mA g-1 even after 1000 cycles).

RESUMEN

Carbon fiber reinforced polymer (CFRP) composites are popular materials in the aerospace and automotive industries because of their low weight, high strength, and corrosion resistance. However, wrinkles or geometric distortions in the composite layers significantly reduce their mechanical performance and structural integrity. This paper presents a method for non-destructively extracting the three-dimensional geometry, lamina by lamina, of a laminated composite. A method is introduced for fabricating consistent out-of-plane wrinkled CFRP laminate panels, simulating the in-service wrinkle observed in industries that utilize thick structure composites such as the vertical lift or wind power industries. The individual lamina geometries are extracted from the fabricated coupon with an embedded wrinkle from captured ultrasonic waveforms generated from single-element conventional ultrasonic (UT) scan data. From the extracted waveforms, a method is presented to characterize the wrinkle features within each individual lamina, specifically the spatially varying wrinkle height and intensity for the wrinkle. Parts were fabricated with visibly undetectable wrinkles using a wet layup process and a hot press for curing. Scans were performed in a conventional immersion tank scanning system, and the scan data were analyzed for wrinkle detection and characterization. Extraction of the layers was performed based on tracking the voltage peaks from A-scans in the time domain. Spatial Gaussian averaging was performed to smooth the A-scans, from which the surfaces were extracted for each individual lamina. The extracted winkle surface aligned with the anticipated wrinkle geometry, and a single parameter for quantification of the wrinkle intensity for each lamina is presented.

RESUMEN

This work focuses on the synthesis of titanium nitride-carbon (TiN-carbon) composites by the thermal decomposition of a titanyl phthalocyanine (TiN(TD)) precursor into TiN. The synthesis of TiN was also performed using the sol-gel method (TiN(SG)) of an alkoxide/urea. The structure and morphology of the TiN-carbon and its precursors were characterized by XRD, FTIR, SEM, TEM, EDS, and XPS. The FTIR results confirmed the presence of the titanium phthalocyanine (TiOPC) complex, while the XRD data corroborated the decomposition of TiOPC into TiN. The resultant TiN exhibited a cubic structure with the FM3-M lattice, aligning with the crystal system of the synthesized TiN via the alkoxide route. The XPS results indicated that the particles synthesized from the thermal decomposition of TiOPC resulted in the formation of TiN-carbon composites. The TiN particles were present as clusters of small spherical particles within the carbon matrix, displaying a porous sponge-like morphology. The proposed thermal decomposition method resulted in the formation of metal nitride composites with high carbon content, which were used as anodes for Li-ion half cells. The TiN-carbon composite anode showed a good specific capacity after 100 cycles at a current density of 100 mAg-1.

RESUMEN

Here, we present surface analysis and biocompatibility evaluation of novel composite material based on graphene oxide traded as Hastalex. First, the surface morphology and elemental analysis of the pristine material were examined by atomic force and scanning electron microscopies, and by energy-dispersive and X-ray photoelectron spectroscopies, respectively. The Hastalex surface was then modified by plasma (3 and 8 W with exposure times up to 240 s), the impact of which on the material surface wettability and morphology was further evaluated. In addition, the material aging was studied at room and elevated temperatures. Significant changes in surface roughness, morphology, and area were detected at the nanometer scale after plasma exposure. An increase in oxygen content due to the plasma exposure was observed both for 3 and 8 W. The plasma treatment had an outstanding effect on the cytocompatibility of Hastalex foil treated at both input powers of 3 and 8 W. The cell number of human MRC-5 fibroblasts on Hastalex foils exposed to plasma increased significantly compared to pristine Hastalex and even to tissue culture polystyrene. The plasma exposure also affected the fibroblasts' cell growth and shape.

RESUMEN

Carbon-based materials are one of the ideal negative electrode materials for potassium ion batteries. However, the limited active sites and sluggish diffusion ion kinetics still hinder its commercialization process. To address these problems, we design a novel carbon composite anode, by confining highly reactive short-chain sulfur molecules into nitrogen-doped hollow carbon nanospheres (termed SHC-450). The formation process involves the controlled synthesis of hollow polyaniline (PANI) nanospheres as precursors via an Ostwald ripening mechanism and subsequent sulfuration treatment. The high content of constrained short-chain sulfur molecules (20.94 wt%) and considerable N (7.15 wt%) ensure sufficient active sites for K+ storage in SHC-450. Accordingly, the SHC-450 electrode exhibits a high reversible capacity of 472.05 mAh g-1 at 0.1 A g-1 and good rate capability (172 mAh g-1 at 2 A g-1). Thermogravimetric analysis shows that SHC-450 has impressive thermal stability to withstand a high temperature of up to 640 °C. Ex situ spectroscopic characterizations reveal that the short-chain sulfur provides high capacity through reversible formation of K2S. Moreover, its special hollow structure not only provides ample space for highly active short-chain sulfur reactants but also effectively mitigates volume expansion during the sulfur conversion process. This work offers new perspectives on enhanced K+ storage performance from an interesting anode design and the space-limited domain principle.

RESUMEN

Advancements in sensor technology have significantly enhanced atmospheric monitoring. Notably, metal oxide and carbon (MOx/C) hybrids have gained attention for their exceptional sensitivity and room-temperature sensing performance. However, previous methods of synthesizing MOx/C composites suffer from problems, including inhomogeneity, aggregation, and challenges in micropatterning. Herein, we introduce a refined method that employs a metal-organic framework (MOF) as a precursor combined with direct laser writing. The inherent structure of MOFs ensures a uniform distribution of metal ions and organic linkers, yielding homogeneous MOx/C structures. The laser processing facilitates precise micropatterning (< 2 µm, comparable to typical photolithography) of the MOx/C crystals. The optimized MOF-derived MOx/C sensor rapidly detected ethanol gas even at room temperature (105 and 18 s for response and recovery, respectively), with a broad range of sensing performance from 170 to 3,400 ppm and a high response value of up to 3,500%. Additionally, this sensor exhibited enhanced stability and thermal resilience compared to previous MOF-based counterparts. This research opens up promising avenues for practical applications in MOF-derived sensing devices.

RESUMEN

In this work, a novel boehmite-modified carbon adsorbent (BMCC) derived from moldy corn was used for simultaneous removal of P and bisphenol A (BPA) from livestock wastewater. The results showed that BMCC had a high specific surface area (308.82 m2/g) with boehmite nanoparticles anchored on its surface. BMCC showed high P and BPA decontamination capabilities (40.98 mg/g for P and 54.65 mg/g for BPA by Langmuir model). The adsorbed amount of P declined as pH increased from 4 to 10, while the adsorbed amount of BPA remained steady until pH increased to 10. After 6 cycles of BMCC use, the P and BPA adsorption efficiencies reduced by 21.75 % and 19.41 %, respectively. The adsorption of P was dominated by electrostatic attraction and complexation, while the adsorption of BPA was controlled by hydrogen bonding, electrostatic interaction, and π-π association. In conclusion, BMCC is an effective treatment for decontaminating P- and BPA-contaminated livestock wastewater.

Asunto(s)

RESUMEN

Surface-dependent non-radical oxidation of carbon materials-based persulfate systems show a better application prospect in the removal of pollutants in complex wastewater. However, their potential is severely limited by the restricted liquid-to-solid mass transfer efficiency of conventional suspension systems. In this paper, a nitrogen-doped carbon encapsulating iron-based nanoparticles (Fe@NC) was prepared, and loaded onto a polyvinylidene fluoride (PVDF) membrane to construct a novel catalytic membrane Fe@NC/PVDF. The Fe@NC/PVDF/PMS system could achieve 99.74% of 2,4-dicholophenol (2,4-DCP) removal within a retention time of 0.867 s, the kinetic constant is 840 times higher than that of Fe@NC/PMS system, and 2-5 orders of magnitude higher than that of various reported advanced oxidation processes systems. The system exhibits strong anti-interference to various water matrices, long-time operational stability at high flux (306 L·m-2·h-1), universality to pollutants that do not contain strong electron-withdrawing groups and mitigation of membrane fouling. Mechanism studies indicate that the electron transfer pathway dominates the 2,4-DCP removal, and singlet oxygen (1O2) plays an auxiliary role. The higher mass transfer efficiency of the filtration mode releases the full potential of the non-radical pathway. This paper provides theoretical and technical support for the development and efficient utilization of carbon-based materials with excellent persulfate catalytic properties.

RESUMEN

Cu(I)-catalyzed 1,3-dipolar cycloaddition (CuAAC), also known as click chemistry, has been demonstrated to be highly robust while providing versatile surface chemistry. One specific application is biosensor fabrication. Recently, we developed thermoplastic electrodes (TPEs) as an alternative to traditional carbon composite electrodes in terms of cost, performance, and robustness. However, their applications in biosensing are currently limited due to a lack of facile methods for electrode modification. Here, we demonstrate the feasibility of using CuAAC following the diazonium grafting of TPEs to take advantage of two powerful technologies for developing a customizable and versatile biosensing platform. After a stepwise characterization of the electrode modification procedures was performed, electrodes were modified with model affinity reagents. Streptavidin and streptavidin-conjugated IgG antibodies were successfully immobilized on the TPE surface, as confirmed by electrochemical impedance spectroscopy and X-ray photoelectron spectroscopy.

RESUMEN

ZVI@C-MP is a novel composite particle consisting of zero-valent iron (ZVI) enclosed within a carbon shell. The purpose of this composite material is to enhance the anaerobic treatment of wastewater containing chloramphenicol (CAP). This approach aims to address the initial challenge of excessive corrosion experienced by ZVI, followed by its subsequent passivation and inactivation. ZVI@C-MP was synthesized through a hydrothermal process and calcination, with montmorillonite as binder, it exhibits stability, iron-carbon microelectrolysis (ICME) properties, and strong adsorption for CAP. Its ICME actions include releasing iron ions (0.70 mg/L) and COD (11.3 mg/L), generating hydrogen (3.82%), and raising the pH from 6.30 to 7.71. With minimal structural changes, it achieved release equilibrium. ZVI@C-MP boasts high removal efficiency of CAP (98.96%) by adsorption, attributed to surface characteristics (surface area: 167.985 m2/g; pore volume: 0.248 cm3/g). The addition of ZVI@C-MP increases COD removal (10.16%), methane production (72.86%), and reduces extracellular polymeric substances (EPS) from 70.58 to 52.72 mg/g MLVSS. It reduces microbial by-products and toxic effects, enhancing CAP biodegradation and microbial metabolic activity. ZVI@C-MP's electrical conductivity and biocompatibility bolster functional flora for interspecies electron transfer. It's a novel approach to antibiotic wastewater treatment.

Asunto(s)

RESUMEN

The composites of transition metal-doped titania and carbon have emerged as promising supports for Pt electrocatalysts in PEM fuel cells. In these multifunctional supports, the oxide component stabilizes the Pt particles, while the dopant provides a co-catalytic function. Among other elements, Sn is a valuable additive. Stong metal-support interaction (SMSI), i.e., the migration of a partially reduced oxide species from the support to the surface of Pt during reductive treatment is a general feature of TiO2-supported Pt catalysts. In order to explore the influence of SMSI on the stability and performance of Pt/Ti0.8Sn0.2O2-C catalysts, the structural and catalytic properties of the as prepared samples measured using XRD, TEM, XPS and electrochemical investigations were compared to those obtained from catalysts reduced in hydrogen at elevated temperatures. According to the observations, the uniform oxide coverage of the carbon backbone facilitated the formation of Pt-oxide-C triple junctions at a high density. The electrocatalytic behavior of the as prepared catalysts was determined by the atomic closeness of Sn to Pt, while even a low temperature reductive treatment resulted in Sn-Pt alloying. The segregation of tin oxide on the surface of the alloy particles, a characteristic material transport process in Sn-Pt alloys after oxygen exposure, contributed to a better stability of the reduced catalysts.

RESUMEN

Carbon disulfide (CS2) is one of the sulfur components that are naturally present in petroleum fractions. Its presence causes corrosion issues in the fuel facilities and deactivates the catalysts in the petrochemical processes. It is a hazardous component that negatively impacts the environment and public health due to its toxicity. This study used zinc-carbon (ZC) composite as a CS2 adsorbent from the gasoline fraction model component. The carbon is derived from date stone biomass. The ZC composite was prepared via a homogenous precipitation process by urea hydrolysis. The physicochemical properties of the prepared adsorbent are characterized using different techniques. The results confirm the loading of zinc oxide/hydroxide carbonate and urea-derived species on the carbon surface. The results were compared by the parent samples, raw carbon, and zinc hydroxide prepared by conventional and homogeneous precipitation. The CS2 adsorption process was performed using a batch system at atmospheric pressure. The effects of adsorbent dosage and adsorption temperatures have been examined. The results indicate that ZC has the highest CS2 adsorption capacity (124.3 mg.g-1 at 30 °C) compared to the parent adsorbents and the previously reported data. The kinetics and thermodynamic calculation results indicate the spontaneity and feasibility of the CS2 adsorption process.

Asunto(s)

RESUMEN

This work integrated a lab-made conductive graphite/polylactic acid (Grp/PLA, 40:60% w/w) filament into a 3D pen to print customized electrodes (cylindrical design). Thermogravimetric analysis validated the incorporation of graphite into the PLA matrix, while Raman spectroscopy and scanning electron microscopy images indicated a graphitic structure with the presence of defects and highly porous, respectively. The electrochemical features of the 3D-printed Gpt/PLA electrode were systematically compared to that achieved using commercial carbon black/polylactic acid (CB/PLA, from Protopasta®) filament. The 3D printed Gpt/PLA electrode "in the native form" provided lower charge transfer resistance (Rct = 880 Ω) and a more kinetically favored reaction (K0 = 1.48 × 10-3 cm s-1) compared to the 3D printed CB/PLA electrode (chemically/electrochemically treated). Moreover, a method by batch injection analysis with amperometric detection (BIA-AD) was developed to determine atorvastatin (ATR) in pharmaceutical and water samples. Using the 3D printed Gpt/PLA electrode, a wider linear range (1-200 µmol L-1), sensitivity (3-times higher), and lower detection limit (LOD = 0.13 µmol L-1) were achieved when compared to the CB/PLA electrode. Repeatability studies (n = 15, RSD <7.3%) attested to the precision of the electrochemical measurements, and recovery percentages between 83 and 108% confirmed the accuracy of the method. Remarkably, this is the first time that ATR has been determined by the BIA-AD system and a low-cost 3D-printed device. This approach is promising to be implemented in research laboratories for quality control of pharmaceuticals and can also be useful for on-site environmental analysis.

Asunto(s)