RESUMEN

An automated dead-end (single pass, no recirculation) ultrafiltration device, the Portable Multi-use Automated Concentration System (PMACS), was evaluated as a means to concentrate Escherichia coli O157:H7 from 40 liters of simulated commercial lettuce wash water. The assessment included generating, sieving, and concentrating sanitizer-free lettuce wash water, either uninoculated or inoculated with green fluorescent protein-transformed E. coli O157:H7 at a high (1.00 log CFU/ml) or low (-1.00 log CFU/ml) concentration. Cells collected within the filters were recovered in approximately 400 ml of buffer to create lettuce wash retentates. The extent of concentration was determined by viable plate counts using a medium selective for the transformed E. coli O157:H7. The samples were qualitatively analyzed for E. coli O157:H7 according to the U. S. Food and Drug Administration Bacteriological Analytical Manual enrichment method and with an electrochemiluminescence immunoassay. This concentration method was then evaluated in a pilot-scale production line at Michigan State University using chlorinated (100, 30, and 10 ppm of available chlorine) lettuce wash water. The total PMACS processing times were 82 ± 6 and 65 ± 5 min for sanitizer-free and chlorinated washes, respectively. Overall, E. coli O157:H7 populations were approximately 2 log higher in retentates than in unconcentrated lettuce wash samples. The higher E. coli O157:H7 levels in the retentates enabled cultural and electrochemiluminescence immunoassay detection in some samples when the corresponding lettuce wash samples were negative. When combined with standard and rapid detection methods, the PMACS concentration method may provide a means to enhance pathogen monitoring of produce wash water.

Asunto(s)

RESUMEN

An automated concentration system (ACS) based on dead-end ultrafiltration was used in this study to concentrate bacteria, including Escherichia coli O157:H7, from 50-liter produce washes (PWs, sieved produce wash). Cells trapped in the filters were recovered in approximately 400 ml of buffer to create PW retentates (PWRs). Extent of concentration was determined by analyzing PWs and PWRs for total coliform bacteria and E. coli O157:H7 using standard methods. In addition, an electrochemiluminescence immunoassay was evaluated for detection of E. coli O157:H7 in spiked PWs and PWRs to demonstrate usefulness of the ACS for same-day detection. The levels of total coliform bacteria and E. coli O157:H7 in PWRs were higher than those in PWs by 1.85 ± 0.41 log most probable number per 100 ml and 1.82 ± 0.24 log CFU/ml, respectively. Electrochemiluminescence detection of E. coli O157:H7 was accomplished within 2 h using ACS concentration of lettuce and spinach wash water artificially spiked with the pathogen at levels as low as 0.36 log CFU/ml and 1.39 log CFU/ml, respectively. Detection of E. coli O157:H7 at -0.93 ± 0.15 log CFU/ml in lettuce wash occurred within approximately 6 h when a 4-h enrichment step was added to the procedure. Use of dead-end ultrafiltration increased bacterial concentrations in PWR and allowed same-day detection of low levels of E. coli O157:H7 in PW. This concentration system could be useful to improve the sensitivity of current rapid methods for detection of low levels of foodborne pathogens in PW water.

Asunto(s)

RESUMEN

The formation of a thin antibody film on a glass surface using pneumatic spray was investigated as a potential immobilization technique for capturing pathogenic targets. Goat-Escherichia coli O157:H7 IgG films were made by pneumatic spray and compared against the avidin-biotin bridge immobilized films by assaying with green fluorescent protein (GFP) transformed E. coli O157:H7 cells and fluorescent reporter antibodies. Functionality, stability, and immobilization of the films were tested. The pneumatic spray films had lower fluorescence intensity values than the avidin-biotin bridge films but resulted in similar detection for E. coli O157:H7 at 10(5)-10(7)cells/ml sample concentrations with no detection of non-E. coli O157:H7 strains. Both methods also resulted in similar percent capture efficiencies. The results demonstrated that immobilization of antibody via pneumatic spray did not render the antibody non-functional and produced stable antibody films. The amount of time necessary for immobilization of the antibody was reduced significantly from 24h for the avidin-biotin bridge to 7 min using the pneumatic spray technique, with additional benefits of greatly reduced use of materials and chemicals. The pneumatic spray technique promises to be an alternative for the immobilization of antibodies on glass slides for capturing pathogenic targets and use in biosensor type devices.

Asunto(s)

RESUMEN

Background. Although sputum smears are the gold standard for diagnosis of tuberculosis, sensitivity in HIV/TB coinfection cases is low, indicating a need for alternative methods. Urine is being increasingly evaluated. Materials and Methods. A novel method for detecting Mycobacterium tuberculosis (MTB) in synthetic urine using a combined IMS/ATP assay was evaluated. Preliminary work established standard ATP conditions and the sensitivity and specificity of the MTB antibody. Eighty-four blinded samples in four replicate assays were evaluated for the presence of MTB using labeled immunomagnetic beads for capture. Beads were separated, washed, and resuspended in broth and added to a microtiter plate. Bioluminescent output was measured and signal-to-noise ratios were calculated. All samples were plated on Middlebrook 7H10 agar or trypticase soy agar to determine limit of detection and recoveries. Results and Conclusions. MTB was distinguished from common bacteriuria isolates and other nontarget bacteria by its ATP results. IMS/ATP successfully detected 19 of 28 samples of MTB in synthetic urine with a limit of detection of 10(4) CFU/ml. Sensitivity and specificity were 67.9% and 82.1%, respectively. This assay offers a possible rapid screening method for HIV-positive patients with suspected coinfection to improve MTB diagnosis.

RESUMEN

The central focus of this study is on the antibacterial and antifungal properties of synthetically produced S,S'-bis(heterosubstituted) disulfides as a means to control the growth of various infection-causing pathogens. Staphylococcus aureus, Francisella tularensis and Candida albicans were each found to be highly susceptible to several of these compounds by agar or broth dilution and Kirby-Bauer diffusion assays. These structurally simple, low molecular weight disulfides have shown promising bioactivities and may serve as leads to the development of effective new antibacterials for pathogenic bacteria such as methicillin-resistant S. aureus and F. tularensis.

Asunto(s)

RESUMEN

Pathogen detection using biosensors is commonly limited due to the need for sensitivity and specificity in detecting targets within mixed populations. These issues were addressed through development of a dual labeling method that allows for both liquid-phase fluorescence in situ hybridization (FISH) and capture antibody targeted detection (CAT-FISH). CAT-FISH was developed using Escherichia coli O157:H7 and Staphylococcus aureus as representative bacteria, and processing techniques were evaluated with regard to FISH intensities and antibody recognition. The alternative fixative solution, methacarn, proved to be superior to standard solid-phase paraformaldehyde fixation procedures, allowing both FISH labeling and antibody recognition. CAT-FISH treated cells were successfully labeled with FISH probes, captured by immunomagnetic separation using fluorescent cytometric array beads, and detected using a cytometric array biosensor. CAT-FISH treated cells were detectable with LODs comparable to the standard antibody-based technique, (~10(3)cells/ml in PBS), and the technique was also successfully applied to two complex matrices. Although immunomagnetic capture and detection using cytometric arrays were demonstrated, CAT-FISH is readily applicable to any antibody-based fluorescence detection platform, and further optimization for sensitivity is possible via inclusion of fluorescently tagged antibodies. Since the confidence level needed for positive identification of a detected target is often paramount, CAT-FISH was developed to allow two separate levels of specificity, namely nucleic acid and protein signatures. With proper selection of FISH probes and capture antibodies, CAT-FISH may be used to provide rapid detection of target pathogens from within complex matrices with high levels of confidence.

Asunto(s)

RESUMEN

The purpose of this study was to develop a detection method for viable E. coli O157:H7 in fresh produce and recreational water. The method was evaluated using eight samples of produce wash and recreational water with or without spiked E. coli O157:H7 at ≤10(2) CFU·ml(-1) and concentrated using dead-end ultrafiltration (DEUF) to produce primary and secondary retentates. Fifty-four matrix replicates of undiluted secondary retentates or dilutions (1:2 or 1:10 in buffer) were evaluated using an IMS/ATP bioluminescence assay (IMS/ATP). Combining primary and secondary DEUF yielded a 2-4 log(10) increase in E. coli O157:H7 concentrations in spiked samples and resulted in signal-to-noise ratios 2-219 fold higher than controls, depending on the sample type. DEUF increased the concentration of E. coli O157:H7 to within the detectable limits of IMS/ATP. The combined assay provided detection of viable E. coli O157:H7 in produce and recreational water. Accurate detection of microbial pathogens using DEUF and IMS/ATP could reduce disease outbreaks from contaminated water sources and food products.

Asunto(s)

RESUMEN

Contamination of fresh produce with Escherichia coli O157:H7 and other pathogens commonly causes food-borne illness and disease outbreaks. Thus, screening for pathogens is warranted, but improved testing procedures are needed to allow reproducible same-day detection of low initial contamination levels on perishable foods, and methods for detecting numerous pathogens in a single test are desired. Experimental procedures were developed to enable rapid screening of spinach for E. coli O157:H7 by using multiplex-capable immunological assays that are analyzed using biosensors. Detection was achieved using an automated electrochemiluminescent (ECL) assay system and a fluorescence-based cytometric bead array. Using the ECL system, less than 0.1 CFU of E. coli O157:H7 per gram of spinach was detected after 5 h of enrichment, corresponding to 6.5 h of total assay time. Using the cytometric bead array, less than 0.1 CFU/g was detected after 7 h of enrichment, with a total time to detection of less than 10 h. These results illustrate that both biosensor assays are useful for rapid detection of E. coli O157:H7 on produce in time frames that are comparable to or better than those of other testing formats. Both methods may be useful for multiplexed pathogen detection in the food industry and other testing situations.

Asunto(s)

RESUMEN

Hollow-fiber ultrafiltration (HFUF) and PCR were combined to detect human-associated microbial source tracking marker genes in large volumes of fresh and estuarine Florida water. HFUF allowed marker detection when membrane filtration did not, demonstrating HFUF's ability to facilitate detection of diluted targets by PCR in a variety of water types.

Asunto(s)

RESUMEN

Rapid identification of viable bacterial contaminants in food products is important because of their potential to cause disease. This study examined a method for microbial detection by using a combined ATP bioluminescence immunoassay. Escherichia coli O157:H7 and Salmonella enterica serovar Typhimurium were selected as target organisms because of their implication in foodborne illness. Various matrices containing the target cells were examined, including ground beef homogenate, apple juice, milk, and phosphate-buffered saline. Specific antibodies were immobilized on the surface of 96-well plates, and then the sample matrices containing target cells in the wells were incubated. Sample matrix (no cells) was used to establish background. The plates were washed, and the wells were incubated with BacTiter-Glo reagent in Mueller-Hinton II broth. Bioluminescent output was measured with the GloMax 96 luminometer. Signal-to-noise ratios were calculated, resulting in a limit of detection of 10(4) CFU/ml for both E. coli O157:H7 and Salmonella Typhimurium. The limit of detection for both species was not affected by the presence of nontarget cells. The various sample matrices did not affect signal-to-noise ratios when E. coli O157:H7 was the target. A weak matrix effect was observed when Salmonella Typhimurium was the target. A strong linear correlation was observed between the number of cells and luminescent output over 4 orders of magnitude for both species. This method provides a means of simultaneously detecting and identifying viable pathogens in complex matrices, and could have wider application in food microbiology.

Asunto(s)

RESUMEN

Although nearly all newly derived water purification methods have improved the water quality in developing countries, few have been accepted and maintained for long-term use. Field studies indicate that the most beneficial methods use indigenous resources, as they are both accessible and accepted by communities they help. In an effort to implement a material that will meet community needs, two fractions of mucilage gum were extracted from the Opuntia ficus-indica cactus and tested as flocculation agents against sediment and bacterial contamination. As diatomic ions are known to affect both mucilage and promote cell aggregation, CaCl(2) was studied in conjunction and compared with mucilage as a bacteria removal method. To evaluate performance, ion-rich waters that mimic natural water bodies were prepared. Column tests containing suspensions of the sediment kaolin exhibited particle flocculation and settling rates up to 13.2 cm/min with mucilage versus control settling rates of 0.5 cm/min. Bacillus cereus tests displayed flocculation and improved settling times with mucilage concentrations lower than 5 ppm and removal rates between 97 and 98% were observed for high bacteria concentration tests (>10(8) cells/ml). This natural material not only displays water purification abilities, but it is also affordable, renewable and readily available.

Asunto(s)

RESUMEN

Using a newly developed fluorescent nanoparticle (NP) that gives rise to a high-intensity and stable fluorescent light, a sensitive antibody (Ab) microarray assay system has been developed for specific detection of bioterrorism agents, as exemplified by ricin, cholera toxin (CT), and staphylococcal enterotoxin B (SEB). The Ab microarray uses a sandwich format that consists of capture Abs, analytes (toxins), biotinylated detection Abs, and avidin-conjugated NP. In all three cases, polyclonal Abs (pAbs) displayed superiority over monoclonal antibodies (mAbs) in capturing toxins on microarray slides even when the pAbs and mAbs had similar affinity as determined by enzyme-linked immunosorbent assay (ELISA). The detection system was successfully used to detect toxins spiked in milk, apple cider, and blood samples. We were able to detect ricin at 100 pg/ml in buffer and at 1 ng/ml in spiked apple cider or milk, whereas CT and SEB were detected at 10 pg/ml in buffer and 100 pg/ml in spiked apple cider or milk. High specificities were also demonstrated in the detection of mixed toxin samples with similar sensitivities. The matrix effect of blood samples on the detection of mixed toxins seems to be minimal when the toxin concentration is at or above 100 ng/ml. The current study highlights the significant role of pAb and NP in increasing selectivity and sensitivity of toxin detection in a microarray format.

Asunto(s)

RESUMEN

Same-day microbial water quality assessments are not possible with standard methods, which increases the possibility of public exposure to fecal pathogens. This study examined the efficacy of high-volume hollow fibre ultrafiltration coupled to biosensor detection for enterococci in marine waters to allow same-day public notification of poor water quality. Fifty-six 1001 ultrafiltered samples and 100 ml grab samples were collected weekly from May to July 2007. Post-ultrafiltration processing included sonication and micron sieve passage to remove interfering particulates, followed by centrifugation for secondary concentration. Levels of enterococci in grab and ultrafiltration samples were determined by a standard method (EPA method 1600) for calculation of recovery efficiencies and concentration factors. Each final retentate was analysed with the RAPTOR evanescent wave biosensor. Enterococci levels increased over 26,000-fold in final retentates. Enterococci were detected when ambient concentrations exceeded the regulatory standard for a single sample (> or = 105 CFU/100 ml), and detection was highly correlated with breaches of the single-sample regulatory limit. The combined procedure required 2.5 h for detection compared with 24h for EPA method 1600. This field study achieved rapid detection of enterococci by ultrafiltration, secondary concentration and biosensor analysis, and demonstrates its potential usefulness for water quality monitoring.

Asunto(s)

RESUMEN

Recent efforts in our laboratory have explored the use of polyacrylate nanoparticles in aqueous media as stable emulsions for potential applications in treating drug-resistant bacterial infections. These emulsions are made by emulsion polymerization of acrylated antibiotic compounds in a mixture of butyl acrylate and styrene (7:3 wt/wt) using sodium dodecyl sulfate as a surfactant. Prior work in our group established that the emulsions required purification to remove toxicity associated with extraneous surfactant present in the media. This article summarizes our investigations of poly(butyl acrylate-styrene) emulsions made using anionic, cationic, zwitterionic, and noncharged (amphiphilic) surfactants, as well as attachable surfactant monomers (surfmers), comparing the cytotoxicity and microbiological activity levels of the emulsion both before and after purification. Our results show that the attachment of a polymerizable surfmer onto the matrix of the nanoparticle neither improves nor diminishes cytotoxic or antibacterial effects of the emulsion, whether or not the emulsions are purified, and that the optimal properties are associated with the use of the nonionic surfactants versus those carrying anionic, cationic, or zwitterionic charge. Incorporation of an N-thiolated beta-lactam antibacterial agent onto the nanoparticle matrix via covalent attachment endows the emulsion with antibiotic properties against pathogenic bacteria such as methicillin-resistant Staphylococcus aureus, without changing the physical properties of the nanoparticles or their emulsions. FROM THE CLINICAL EDITOR: Emulsions of polyacrylate nanoparticles, antibiotics and surfactants were studied using surfactant monomers as controls. Nonionic surfactants resulted in the most optimal properties. Incorporation of a beta-lactam antibacterial agent onto the nanoparticle matrix endowed the emulsion with antibiotic properties against methicillin-resistant Staphylococcus aureus (MRSA), a leading cause of hospital acquired, treatment-resistant infections including sepsis.

Asunto(s)

RESUMEN

N-thiolated beta-lactams had previously been shown to have antibacterial activity against a narrow selection of pathogenic bacteria including Staphylococcus aureus and Bacillus anthracis, as well as apoptotic-inducing activity in a variety of human cancer cell lines. We now have found that these lactams also possess antifungal activity against Candida and other fungi by exerting powerful cytostatic effects that disrupt the structural integrity of cytoplasmic membranes. The mode of action and structure-activity trends of these lactams as antifungals parallel that previously seen in our antibacterial studies.

Asunto(s)

RESUMEN

Monitoring recreational waters for fecal contamination by standard methodologies involves culturing indicator bacteria, such as fecal coliforms and enterococci. Delayed reporting of microbial water quality parameters increases the likelihood of public exposure to pathogens of fecal origin, making the development of rapid methods important for public health protection. A rapid assay for enterococci was developed using a combined ultrafiltration-biosensor procedure. Twelve 100-liter water samples were collected from upper Tampa Bay over a 9-month period. The samples were collected on site by dead-end hollow-fiber ultrafiltration. Postfiltration processing of the initial retentates included sonication and micrometer-level sieve passage to remove interfering particles. Centrifugation was utilized for secondary concentration. Grab samples were collected simultaneously with the ultrafiltered samples. Concentrations of enterococci in all grab and ultrafiltration samples were determined by the standard method (EPA method 1600) for calculation of recovery efficiencies and concentration factors. Levels of enterococci increased twofold in initial retentates and by 4 orders of magnitude in final retentates over ambient concentrations. An aliquot of each final retentate was adsorbed onto polystyrene waveguides for immunoassay analysis of enterococci with a microfluidic fiber optic biosensor, the Raptor. Enterococci were detected when concentrations in the ambient water exceeded the regulatory standard for a single sample (> or =105 CFU/100 ml). The combined ultrafiltration-biosensor procedure required 2.5 h for detection compared to 24 for the standard method. This study demonstrated that enterococci can be detected rapidly using on-site ultrafiltration, secondary concentration, and biosensor analysis.

Asunto(s)

RESUMEN

Disease has become an increasingly important issue for wildlife management over the past two decades. Adequate surveillance is fundamental for disease prevention and control, thus there is an increasing need for diagnostic assays for wildlife management. The objective of this study was to evaluate the performance of a field-portable biosensor adapted for rapid detection of specific antibodies in tortoise plasma that reflect a history of exposure to Mycoplasma agassizii, which is an agent of tortoise upper respiratory tract disease. Banked plasma samples were tested in two blinded trials, and the parameters that define the reliability of a diagnostic test were estimated based on externally validated tortoise plasma controls. The mean sensitivity of the biosensor (ability to identify exposed tortoises in the group of all exposed individuals) was 78%; the mean specificity (unexposed individuals with negative test result, out of all unexposed individuals tested) was 73%; the mean positive predictive value (exposed individuals with positive test, out of all individuals with positive test) was 82%; the mean negative predictive value (unexposed individuals with negative test, out of all individuals with negative test) was 68%. In a 15-min field-portable format, the biosensor was able to discriminate between true seropositive (n=34) and true seronegative (n=23) tortoise plasma with overall accuracy of 84%. The goals established for the tortoise population can help managers decide whether potential diagnostic errors should impact management decision-making, and whether the benefits of the field-portable format of the biosensor assay outweigh any potential disadvantages.

Asunto(s)

RESUMEN

One of the known limitations for biosensor assays is the high limit of detection for target cells within complex samples (e.g., Escherichia coli at 10(4) to 10(5) CFU/mL) due to poor capture efficiencies. Currently, researchers can only estimate the cell capture efficiency necessary to produce a positive signal for any type of biosensor using either cumbersome techniques or regression modeling. To solve this problem, green fluorescent protein (GFP) transformed E. coli O157:H7 was used to develop a novel method for directly and easily measuring the cell capture efficiency of any given biosensor platform. For demonstration purposes, E. coli-GFP was assayed on both fiber optic and planar waveguide biosensor platforms. Cells were enumerated using an epifluorescent microscope and digital camera to determine the number of cells captured on the surfaces. Conversion algorithms were used with these digital images to determine the cell density of entire waveguide surface areas. For E. coli-GFP, the range of cell capture efficiency was between 0.4 and 1.2%. This indicates that although the developed model works for calculating cell capture, there is still need for significant improvements in capture methods themselves, to increase the capture efficiency and thereby lower detection limits. The use of GFP-transformed target cells and cell capture efficiency calculations can facilitate the development and optimization processes by allowing direct enumeration of new biosensor design configurations and sample processing strategies.

Asunto(s)

RESUMEN

This report describes the synthesis and evaluation of glycosylated polyacrylate nanoparticles that have covalently-bound antibiotics within their framework. The requisite glycosylated drug monomers were prepared from one of three known antibiotics, an N-sec-butylthio beta-lactam, ciprofloxacin, and a penicillin, by acylation with 3-O-acryloyl-1,2-O-isopropylidene-5,6 bis((chlorosuccinyl)oxy)-d-glucofuranose (7) or 6-O-acetyl-3-O-acryloyl-1,2-O-isopropylidene-5-(chlorosuccinyl)oxy-alpha-d-glucofuranose (10). These acrylated monomers were subjected to emulsion polymerization in a 7:3 (w:w) mixture of butyl acrylate-styrene in the presence of sodium dodecyl sulfate as surfactant (3 weight %) and potassium persulfate as a radical initiator (1 weight %). The resulting nanoparticle emulsions were characterized by dynamic light scattering and found to have similar diameters ( approximately 40 nm) and size distributions to those of our previously studied systems. Microbiological testing showed that the N-sec-butylthio beta-lactam and ciprofloxacin nanoparticles both have powerful in vitro activities against methicillin-resistant Staphylococcus aureus and Bacillus anthracis, while the penicillin-bound nanoparticles have no antimicrobial activity. This indicates the need for matching a suitable antibiotic with the nanoparticle carrier. Overall, the study shows that even relatively large, polar acrylate monomers (MW>1000 amu) can be efficiently incorporated into the nanoparticle matrix by emulsion polymerization, providing opportunities for further advances in nanomedicine.

Asunto(s)

RESUMEN

The validity of ELISA for detection of E. coli O157:H7 under many conditions is not proven. In this work, sELISA was able to detect bacteria after sub-lethal chlorine exposure and after seven days of starvation with little to no change in limit of detection and fluorescence signal as long as chlorine was not present in the sample or was neutralized by sodium thiosulfate. After Colitag enrichment, sELISA detected approximately 3 colony forming units/ml of originally added E. coli O157:H7. Thus, the present sELISA is valid for detection of E. coli O157:H7 in water sources, although sample matrices may interfere with assay.

Asunto(s)