Your browser doesn't support javascript.
loading
Relevant Aspects in the Mechanical and Aging Degradation of NiTi Alloy with R-Phase in Endodontic Files.
Sánchez, Patricia; Vidi, Benedetta; Rico, Cristina; Mena-Alvarez, Jesús; Gil, Javier; Aragoneses, Juan Manuel.
Afiliación
  • Sánchez P; Bioengineering Institute of Technology, Facultad de Medicina y Ciencias de la Salud, Universitat Internacional de Catalunya, 08195 Sant Cugat del Vallés, Spain.
  • Vidi B; Programa de Doctorado Ciencia de la Salud, Universidad de Alcalá, Pza. San Diego s/n, 28801 Alcalá de Henares, Spain.
  • Rico C; Faculty of Dentistry, Universidad Alfonso X El Sabio, C. de Emilio Muñoz, 13, 28691 Madrid, Spain.
  • Mena-Alvarez J; Faculty of Dentistry, Universidad Alfonso X El Sabio, C. de Emilio Muñoz, 13, 28691 Madrid, Spain.
  • Gil J; Faculty of Dentistry, Universidad Alfonso X El Sabio, C. de Emilio Muñoz, 13, 28691 Madrid, Spain.
  • Aragoneses JM; Bioengineering Institute of Technology, Facultad de Medicina y Ciencias de la Salud, Universitat Internacional de Catalunya, 08195 Sant Cugat del Vallés, Spain.
Materials (Basel) ; 17(13)2024 Jul 06.
Article en En | MEDLINE | ID: mdl-38998431
ABSTRACT
One of the most important challenges in endodontics is to have files that have excellent flexibility, toughness, and high fatigue life. Superelastic NiTi alloys have been a breakthrough and the new R-phase NiTi alloys promise to further optimize the good properties of NiTi alloys. In this work, two austenitic phase endodontic files with superelastic properties (Protaper and F6) and two austenitic phase files with the R-phase (M-wire and Reciproc) have been studied. The transformation temperatures were studied by calorimetry. Molds reproducing root canals at different angles (30, 45, and 70°) were obtained with cooling and loads simulating those used in the clinic. Mechanical cycles of different files were realized to fracture. Transformation temperatures were determined at different number of cycles. The different files were heat treated at 300 and 500 °C as the aging process, and the transformation temperatures were also determined. Scanning and transmission electron microscopy was used to observe the fractography and precipitates of the files. The results show that files with the R-phase have higher fracture cycles than files with only the austenitic phase. The fracture cycles depend on the angle of insertion in the root canal, with the angle of 70° being the one with the lowest fracture cycles in all cases. The R-Phase transformation increases the energy absorbed by the NiTi to produce the austenitic to R-phase and to produce the martensitic transformation causing the increase in the fracture cycles. Mechanical cycling leads to significant increases in the transformation temperatures Ms and Af as well as Rs and Rf. No changes in the transformation temperatures were observed for aging at 300 °C, but the appearance of Ni4Ti3 precipitates was observed in the aging treatments to the Nickel-rich files that correspond to those with the R transition. These results should be considered by endodontists to optimize the type of files for clinical therapy.
Palabras clave

Texto completo: 1 Colección: 01-internacional Base de datos: MEDLINE Idioma: En Revista: Materials (Basel) Año: 2024 Tipo del documento: Article País de afiliación: España Pais de publicación: Suiza

Texto completo: 1 Colección: 01-internacional Base de datos: MEDLINE Idioma: En Revista: Materials (Basel) Año: 2024 Tipo del documento: Article País de afiliación: España Pais de publicación: Suiza