RESUMO
Omega-3 rich vegetable oils, such as walnut oil, are gaining interest because of their health benefits. Synthetized homologous series of hydroxytyrosol alkyl esters (HTEs) with different alkyl chain lengths (C4-C18) were incorporated in purified walnut oil (PWO) spray-dried microparticles, designed with Capsul® (C) as encapsulating agent and sodium alginate (SA) as outer layer (PWO-C/SA). The encapsulation efficiency (>87%) and Tg of PWO-C/SA microparticles were not affected by the HTEs. The incorporation of HTE-C10 increased the melting point (185.0 ± 1.3 °C), decreasing the formation of Dimers + Polymers (1.12 ± 0.05% at day 35 of storage) and the crystallinity of the microparticles (>170 °C). The highest stability of PWO-C(HTE-C10)/SA suggests a specific location of HTE-C10 at the oil:water interface. The SA layer delayed the release of fatty acids during in vitro digestion. The incorporation of HTEs of medium chain length can be a suitable strategy to protect unsaturated oils encapsulated by spray-drying.
Assuntos
Antioxidantes , Juglans , Alginatos , Ésteres , Álcool Feniletílico/análogos & derivadosRESUMO
Purified walnut oil (PWO) microparticles with Capsul® (C, encapsulating agent), sodium alginate (SA) as outer layer and ascorbic acid (AA) as oxygen scavenger were obtained by spray drying using a three-fluid nozzle. AA was incorporated in the inner infeed (PWO-C(AA)/SA), in the outer infeed (PWO-C/SA(AA)) and in both infeed (PWO-C(AA)/SA(AA)). PWO-C(AA)/SA (4.56 h) and POW-C(AA)/SA(AA) (2.60 h) microparticles showed higher induction period than POW-C/SA(AA) (1.17 h), and lower formation of triacylglycerol dimers and polymers during storage (40 °C). Therefore, AA located in the inner infeed improved the oxidative stability of encapsulated PWO by removing the residual oxygen. AA in the SA outer layer did not improve the oxidative stability of encapsulated PWO since oxygen diffusion through the microparticles was limited and/or AA weakened the SA layer structure. The specific-location of AA (inner infeed) is a strategy to obtain stable spray-dried polyunsaturated oil-based microparticles for the design of foods enriched with omega-3 fatty acids.
RESUMO
The optimal physical, chemical and nutritional properties of natural lipids depend on the structure and composition of triacylglycerols. However, they are not always mutually compatible. Lipid modification is a good way to give them specific functionalities, increase their oxidative stability, or improve their nutritional value. As such, chemical and enzymatic interesterification may be used to modify them and produce structured lipids. In accordance, the aim of this study is to compare chemical and enzymatic interesterification of binary blends of fully hydrogenated soybean oil and walnut oil, using sodium methoxide or Lipozyme TL IM, respectively, to produce a fat base with adequate nutritional and physical characteristics. Three different mass ratios of fully hydrogenated soybean oil and walnut oil blends (20:80, 40:60 and 60:40) were interesterified and evaluated. Total interesterification was determined by the stabilization of the solid fat content. Chemical reaction of the 20:80 blend was completed in 10 min and of the 40:60 and 60:40 blends in 15 min. Enzymatically interesterified blends were stabilized in 120 min at all of the mass ratios. Complete interesterification significantly reduced the solid fat content of the blends at any composition. Chemical and enzymatically interesterified fully hydrogenated blend of soybean and walnut oil at mass ratio of 40:60 showed the plastic curve of an all-purpose- -type shortening rich in polyunsaturated fatty acids, with a high linolenic acid (C18:3n3) content and with zero trans-fatty acids.