RESUMO

Electrochemical oxidation (EO), electro-Fenton (EF), and photoelectro-Fenton (PEF) with a BDD anode have been comparatively assessed to remediate solutions of Red CL and/or Red WB azo dyes from real raw water. For the EO process in 50 mM Na2SO4 at pH 3.0, the main oxidant was the heterogeneous •OH generated at the anode, whereas in EF and PEF, the cathodic production of H2O2 and the addition of 0.50 mM Fe2+ catalyst additionally originated homogeneous •OH that enhanced the oxidation of organics. In PEF, the solution was illuminated with a 6 W UVA light. An almost total discoloration was always found operating with a 1:1 mixture of 200 mg L-1 of both dyes in 60 min, whose efficiency increased in the order of EO < EF < PEF. The HPLC analysis of the dye mixture treated by PEF disclosed that its degradation process agreed with its discoloration. A high 74% of COD was reduced due to the oxidative action of hydroxyl radicals and the photolysis of final Fe(III)-carboxylate species with UVA irradiation. The process was accompanied by an energy consumption of 0.76 kWh (g COD)-1, a value similar to the energy consumed by the applied UVA light.

Assuntos

RESUMO

Trivalent chromium (Cr(III)) is a contaminant with toxic activity. Its presence in waters and soils is usually related to industrial activities such as tanneries. The aim of this study was to compare the removal of Cr(III) in hydroponic solutions and tannery effluents using two floating macrophytes: Salvinia auriculata and Eichhornia crassipes. First, to determine the chromium removal capacity in solution and the bioaccumulation factor (BAF) in tissues of each plant, experiments were set up with contaminated solutions with Cr(III) concentrations of 2, 5, 10, 20, and 40 mg/L. Subsequently, both plant species were exposed to a primary tannery effluent contaminated with 12 mg/L of Cr(III) in order to study the removal capacity of organic and inorganic matter, as well as the acute toxicity in the water flea (Daphnia magna) and genotoxicity in zebrafish (Danio rerio). Tests carried out on nutrient solutions revealed that both plants have a high capacity for removing Cr(III) in solution. The BAF in tissues was higher in E. crassipes compared to S. auriculata. In the experiments with a tannery effluent, both species presented low nutrient and organic matter removal efficiency, but they showed good Cr(III) removal capacity, with average reduction values of 57% for S. auriculata and 54% for E. crassipes after 72 h of exposure. E. crassipes contributed most to the reduction in acute toxicity in D. magna, while S. auriculata did not show a similar effect. However, both plant species managed to reduce the genotoxicity marker in D. rerio when compared with the initial effluent and the control.

RESUMO

In the present work, a study was carried out on the dosage of wastes from the chemical industry (tannery sludge) and civil construction (concrete and plaster) in mixtures used in concrete blocks' production. The objective was the application of these blocks in paving. The characterization of the materials used was performed employing X-ray diffractometry (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The effect of the different residues on the blocks' properties was evaluated through compressive strength, flexion-traction, water absorption, abrasion resistance, and leaching tests. The results indicated that the concrete paving blocks produced with the addition of residues did not obtain gains in the values of mechanical resistance to compression and traction in bending compared to blocks made with standard raw material. However, the blocks produced with construction waste presented satisfactory results for application in street paving after 7 days of concrete curing, reaching values between 36.54 and 44.6 MPa for the mentioned properties. These values also increased to 21.4% within 28 days of curing. The blocks produced with plaster showed values between 37.03 and 39.85 MPa after 28 days of curing, allowing their use for street paving. On the other hand, the blocks containing residues from the chemical industry had lower strengths, reaching a maximum of 29.36 MPa after 28 days of curing. In addition, it was also noted that the blocks produced with recycled concrete showed an improvement in performance for a composition of 50% recycled material.

Assuntos

RESUMO

Tanneries are considered some of the most polluting industries due to the heavy use of toxic compounds, most of which are released into water bodies, thus exerting adverse effects on aquatic biota. However, the effects on organisms of treated effluents when released into the natural environment are rarely evaluated. This study aims to assess the physicochemical parameters of a tannery effluent after treatment (TE) at a Common Effluent Treatment Plant as well as the water of the receiving stream and to evaluate cytogenotoxic effects in Allium cepa. Three sampling sites (A: TE discharge point; B: 100 m downstream from site A along the receiving stream; C: 100 m upstream from site A along the stream) were selected. Onion bulbs were exposed to TE (100%, 80%, 60% v/v), water samples from sites B and C, and tap water for 72 h. Chromosomal aberration and mitotic index were analyzed on the root cells of A. cepa. The TE was above the standard limits for ammoniacal nitrogen, COD, and total nitrogen. No cytogenotoxicity was observed in A. cepa exposed to samples from sites A and C. However, the stream water sampled downstream from the TE discharge site significantly reduced the mitotic index, indicating a cytotoxic effect. Therefore, this demonstrates the effects of interactions between the receiving water and the complex chemical mixtures in the TE. The findings thus showed that the toxicity assessment of treated effluents along with the receiving water body would provide valuable and more realistic information about the joint toxicity of chemical pollutants in aquatic environments.

Assuntos

RESUMO

Some components found in the composition of the tannery sludge are nutrients for the plants; it can be considered an alternative source of fertilization as they have favorable agronomic characteristics. However, it is reported in some studies that the presence of chromium and sodium in this residue causes physiological and anatomical disturbances that inhibit the development of the plants. The objective of this study was to evaluate the influence of chromium and sodium on the physiology, anatomy, and development of Conilon coffee seedlings grown on substrates produced with tannery sludge and equivalent doses of chromium and sodium. The experiment was carried out in nursery using randomized block design, containing 5 treatments and 7 repetitions. The treatments consisted of the application of a 40% tannery sludge dose and equivalent doses of chromium and sodium mixed with a conventional substrate. Notably, the presence of sodium in the substrate caused greater damage to the plants, negatively influencing the physiology, anatomy, and, consequently, development of the plants, while the presence of chromium suggests that it does not influence much the evaluated characteristics. The treatment with tannery sludge, on the other hand, despite containing the same chromium and sodium contents, revealed a more pronounced negative influence on the physiology, anatomy, and development patterns of the seedlings. This shows that sodium and chromium alone are not the only factors responsible for the lowest growth indicators studied.

Assuntos

RESUMO

El carbunco es una zoonosis que afecta a animales herbívoros, causada por el microorganismo Bacillus anthracis; que se encuentra en su forma vegetativa en el organismo infectado, y una vez en contacto con el aire forma esporas que infectan al huésped, liberando toxinas que inducen edema, septicemia y necrosis tisular. En humanos, la transmisión se produce por cortes, pinchazos o contacto directo de piel lesionada con esporas o tejidos de animales infectados. En Perú, para la década de 1980, se reportaron 400 casos anuales en áreas rurales agrícolas, adquiridos por manipulación del ganado vacuno, muerto por ántrax. Es por ello, que la piel y el cuero procedente de animales infectados representa un riesgo de infección para los trabajadores de industrias curtiembres. Se realizó un estudio transversal para evaluar el riesgo biológico ocupacional y las medidas de bioseguridad relacionadas con el Bacillus anthracis en pequeñas, medianas y grandes empresas curtiembres peruanas. Se aplicó un instrumento a los trabajadores para cuantificar las variables, componentes de riesgo biológico y conocer las medidas higiénicas adoptadas. Posteriormente se calculó e interpretó el nivel de riesgo biológico. Se encontró que el nivel de riesgo supera el límite de exposición biológica para el Bacillus anthracis en todas las empresas evaluadas y los trabajadores de las pequeñas empresas tienen poco conocimiento acerca del riesgo biológico al que están expuestos, siendo necesaria la capacitación de los trabajadores acerca del Bacillus anthracis y adopción de medidas de bioseguridad en empresas curtiembres, que garanticen la salud de los trabajadores(AU)

Anthrax is a zoonosis that affects herbivorous animals, caused by the microorganism Bacillus anthracis; which is found in its vegetative form in the infected organism, and once in contact with the air it forms spores that infect the host, releasing toxins that induce edema, septicemia and tissue necrosis. In humans, transmission occurs through cuts, punctures, or direct contact of broken skin with spores or tissues of infected animals. In Peru, for the 1980s, 400 annual cases were reported in rural agricultural areas, acquired by handling cattle, which died of anthrax. For this reason, the skin and leather from infected animals represent a risk of infection for workers in tanneries. A cross-sectional study was carried out to evaluate the occupational biological risk and biosafety measures related to Bacillus anthracis in small, medium and large Peruvian tanneries. An instrument was applied to the workers to quantify the variables, components of biological risk and to know the hygienic measures adopted. Subsequently, the level of biological risk was calculated and interpreted. It was found that the level of risk exceeds the biological exposure limit for Bacillus anthracis in all the companies evaluated and the workers of the small companies have little knowledge about the biological risk to which they are exposed, being necessary the training of the workers about the Bacillus anthracis and adoption of biosafety measures in tanneries, which guarantee the health of workers(AU)

Assuntos

RESUMO

Enzyme immobilization is an important alternative to stabilize enzyme properties favoring the efficiency of derivatives (enzyme + support/matrix) for different purposes. According to this, the current study aimed to immobilize the Aspergillus fumigatus CAS21 tannase and the use of the derivatives in the treatment of the effluent produced by the tannery industry. The tannase was immobilized on sodium alginate, DEAE-Sephadex, amberlite, and glass pearls as supports. Calcium alginate was the most adequate support for tannase immobilization with 100% yield and 94.3% for both efficiency and activity. The best tannase activity for the calcium alginate derivative was obtained at 50°C-60°C and pH 5.0. Thermal and pH stabilities evaluated for 24 h at 30°C-60°C and pH 4-7, respectively, were improved if compared to the stability of the free enzyme. Considering the reuse of the calcium alginate derivative, 78% of the initial activity was preserved after 10 catalytic cycles, and after the 9-month storage at 4°C, the activity was maintained in 70%. This derivative was applied in a packed bed reactor (PBR) for the treatment of tannin-rich effluents from the tannery industry. The reduction of the tannin content was effective reaching degradation of 74-78% after 48 h of PBR operation. The concentration of total phenolic compounds was also reduced, and the color and clarity of the effluent improved. In conclusion, the calcium alginate derivative is an attractive alternative as biocatalyst for large-scale treatment of the effluents from the tannery industry.

RESUMO

This study concerns Cr(VI) removal using zeolites in a batch system for tannery effluent. In the initial stage, natural zeolite (ZN) and synthetic zeolite (ZS) were characterized, obtaining a Si/Al ratio of 4.64 and 1.60, and with predominant clinoptilolite and faujasite phases, the surface area of 9.34 and 25.82 m2/g and cation exchange capacity of 84.05 and 188.72 meq/100 g, respectively. Subsequently, ZN and ZS were activated with HCl and NaOH. Through preliminary tests, with a solution of K2Cr2O7, it was determined that the highest Cr(VI) removal for both, ZN and ZS, was with NaOH activation, obtaining 82 and 56% removal, respectively. According to Ecuadorian regulations, the Cr(VI) concentration exceeds the maximum permissible limits on the tannery effluent. For this effluent, it was determined that the highest Cr(VI) removal, 45%, is obtained with 1 g of ZN activated with NaOH and 100 mL of effluent. With ZN-NaOH, removal tests were carried out in a fixed bed with 5, 10, and 20 g of natural zeolite. The natural zeolite also has chromium removal capacity in the bed system, achieving similar removals to those obtained in the batch experiments, but decreasing the treatment time. Thus, both natural and synthetic zeolites can remove Cr(VI) in tannery effluents, achieving this effluent with permissible limits.

RESUMO

In Brazil, the leather industry is an important economic segment moving around U$ 3 billions of dollars a year. However, high amounts of water are requested to transform skin animals into leather, causing high wastewater amounts to be consequently produced. A major problem is attached to the presence of chromium in the wastewater from the tanning process. Chromium is a heavy metal potentially toxic both to the environment and to the human health. In order to control the levels of chrome dumped into the environment, Brazilian agencies require the treatment of effluents by the generating source. Thus, this study aimed to develop an alternative method to the removal of chromium in wastewater from the leather industry using the Opuntia ficus-indica biomass as eco-friendly biosorbent. Crude waste samples were collected in a tannery stabilization pond for chromium quantification and further treatments. The powdered Opuntia ficus-indica was obtained from species collected in Pernambuco, Brazil, and its physical parameters and pHPCZ were characterized. Adsorptions studies and acute toxicity were also carried out. The biomass remaining after the sorption was analyzed through scanning electron microscopy and Fourier-transform infrared spectroscopy. The chromium content was above the limit allowed by the Brazilian regulatory agency. In sorption studies, biomass was able to remove 74.8% and 84.88% of Cr (III) using 2.0 g and 4.0 g of biomass, respectively. The surface of biomass is very favorable to biosorption and the chemical bindings among oxygen atoms present in the chemical components of this biomass and the heavy metal was confirmed through infrared spectrum. This study proved that Opuntia ficus-indica is effectively biosorbent to chromium, promising and with low costs for the leather industry, able to reduce its ecotoxicity as proven by chemical and biological assays.

RESUMO

The tannery industry is one of the economic sectors that contributes to the development of different countries. Globally, Europe and Asia are the main producers of this industry, although Latin America and Africa have been growing considerably in recent years. With this growth, the negative environmental impacts towards different ecosystem resources as a result of the discharges of recalcitrated pollutants, have led to different investigations to generate alternative solutions. Worldwide, different technologies have been studied to address this problem, biological and physicochemical processes have been widely studied, presenting drawbacks with some recalcitrant compounds. This review provides a context on the different existing technologies for the treatment of tannery wastewater, analyzing the physicochemical composition of this liquid waste, the impact it generates on human health and ecosystems and the advances in the different existing technologies, focusing on advanced oxidation processes and the use of microalgae. The coupling of advanced oxidation processes with biological processes, mainly microalgae, is seen as a viable biotechnological strategy, not only for the removal of pollutants, but also to obtain value-added products with potential use in the biorefining of the biomass.

Assuntos

RESUMO

The aim of the present study was to obtain an effective vehiculation system in which bacterial agents could maintain viability improving their removal capacity. Herein, we present a novel biohybrid membrane of polymeric nanofibers and free-living bacteria for the simultaneous removal of pollutants. In this system, bacteria are free within the pores between the nanofibers and adsorbed to the surface of the membranes. Association between bacteria and the membranes was performed through a self-formulated medium, and the presence of the bacteria in the polymeric matrix was evidenced through atomic force microscopy (AFM). Biohybrid membranes associated with the remediation agents Bacillus toyonensis SFC 500-1E and Acinetobacter guillouiae SFC 500-1A promoted a reduction of up to 2.5 mg/L of hexavalent chromium and up to 200 mg/L of phenol after 24 h of treatment in synthetic medium containing the contaminants. Similarly, more than 46% of the hexavalent chromium and all of the phenol content were removed after treatment of a tannery effluent with initial concentrations of 7 mg/L of Cr(VI) and 305 mg/L of phenol. Counts of the remediation agents from the membranes were always above 1.107 CFU/g, also in the reutilization assays performed without reinoculation. Biohybrid membranes were hydrolysis-resistant, reusable, and effective in the simultaneous removal of contaminants for more than 5 cycles. Viability of the microorganisms was maintained after long-term storage of the membranes at 4 °C, without the use of microbiological media or the addition of cryoprotectants. Graphical abstract KEY POINTS: • Polymeric membranes were effectively associated with the SFC 500-1 remediation consortium • Biohybrid membranes removed hexavalent chromium and phenol from different matrices • Removal of contaminants was achieved in many successive cycles without reinoculation.

Assuntos

RESUMO

The removal of highly concentrated pollutants, presented in a wastewater mixture from industrial tannery effluents by electrocoagulation, was examined. All experiments were carried out in a rotating cylinder electrode reactor with six aluminum anodes and two sedimentation tanks. The influence of the applied current density and rotational speed on the removal efficiency of an electrocoagulation reactor was studied. Chemical oxygen demand was diminished at 70%, while total suspended solids, chromium (III) and turbidity were almost eliminated (>90%) with 6 mA cm-2 of the applied current density. Additionally, a homogeneous cathodic deposit was obtained at the end of each test. Those cathodic deposits and flocs were analyzed by SEM-EDS. Calculations of the cell energy consumption and the produced aluminum cost were estimated for 6 mA cm-2 and 100 rpm, obtaining 1.98 kWh m-3 and $0.7 USD m-3, respectively.

Assuntos

RESUMO

The search for renewable energies has been one of the biggest challenges of the last decades. Sludge and solid wastes of many sources have been used to produce biogas of high calorific value. Thus, this work aimed to evaluate the biogas production of solid waste originating from a tannery that uses chromium salts as a tanning agent and to characterize the physicochemical parameters and microbial composition of the biogas-producing biomass. Wastes were collected and the parameters were evaluated at the initial and final time points of the anaerobic incubation process. At the end of 150 days, there was a production of 26.1 mL g-1 VSS of biogas with 52% of methane. The highest amount of biomethane observed was related to the archaeal family Methanosaetaceae and bacterial order Bacteroidales. Knowledge about changes in the microbial composition can provide tools for manipulation, isolation, and inoculation of the microorganisms inside the bioreactors to maximize methane production.

Assuntos

RESUMO

Industrial activities such as leather tanning involve the use of highly toxic inorganic pollutants, like Chromium (Cr). This work evaluated Cr(VI) remediation by hairy roots (HR) of Brassica napus, paying close attention to the mechanisms involved and the toxicity of post-removal solutions. Results showed that these roots were capable of tolerating concentrations of up to 10 mg L-1 Cr(VI), while higher concentrations were toxic for HR development. Removal efficiency was assessed through the use of synthetic solutions containing different initial Cr(VI) concentrations (2, 5, or 10 mg L-1). Regardless of these initial concentrations, the highest removal efficiency values were between 80 and 90% after 24 and 48 h of treatment, using a 2.0 g inoculum. The mechanisms involved were Cr accumulation (60%) and to a lesser extent, adsorption to the root biomass (30%). A fraction of Cr(VI) was intracellularly reduced to Cr(III), which suggests reductases may have played a role. Additionally, post-removal toxicity was evaluated through two bioassays (Lactuca sativa L. and AMPHITOX test) after the removal of 10 mg L-1 Cr(VI). The treated solutions showed moderate phytotoxicity for L. sativa L. and no toxicity for R arenarum. The ability of HR to remove 10 mg L-1 Cr(VI) from real tannery effluents collected from a regional industry (Córdoba province, Argentina) was also determined. The high removal efficiency observed (98%) demonstrates this system can be successful in treating complex wastewaters.

Assuntos

RESUMO

The tannery is an important trade in various Peruvian regions; however, tannery effluents are a serious local environmental threat due to its highly toxics components and lack of efficient treatment. The untreated effluents produced by tannery factories in Arequipa Rio Seco Industrial Park (PIRS) have formed a lake in the region nearby. In this work, we study the capability of filamentous fungi species found in this effluents lake with potential for chromium (VI) bioremediation. Fourteen species of filamentous fungi were isolated; only two species were identified Penicillium citrinum and Trichoderma viride, and third strain identified as Penicillium sp. The filamentous fungi showed that are fully tolerant to chromium (VI) concentrations up to 100 mg/L. These fungal strains showed significant growth in chromium (VI) concentrations up to 250 mg/L. Tolerant index (TI) analysis revealed that P. citrinum and T. viride began adaptation to chromium (IV) concentrations of 250 and 500 mg/L, after 6 and 12 days, respectively. When exposed to higher Cr (VI) concentrations (1000 mg/L), only T. viride was able to show growth (enhance phase). Interestingly, one of the significant responses from these fungal strains to increasing chromium (VI) concentrations was an increment in secreted laccase enzymes. Our results show tolerance and adaptation to elevated concentrations of chromium (VI) of these fungal strains suggesting their potential as effective agents for bioremediation of tannery effluents.

Assuntos

RESUMO

Tannery wastewater is characterized by high and variable concentrations of diverse pollutants, which makes it difficult and costly to treat. In the search for sustainable treatment options for tannery effluents, two pilot-scale horizontal subsurface flow (HSF) constructed wetlands (CW) were built and operated for the treatment of synthetic water of quality similar to that of pre-treated tannery effluents. Five different loading phases were examined with gradual increase of inflow COD, NH4+-N and Cr loads until reaching and exceeding the typical composition of a tannery effluent. High COD and NH4+-N removals were observed (82 and 96%, respectively), and almost complete Cr removal in the outflow, which met the Venezuela national standards for environmental discharge. Plant uptake was measured, but microbial processes appear to be the main ammonium transformation/removal mechanism. Nitrogen, chlorophyll and Cr in the plant aerial parts and roots indicated the capacity of Phragmites sp. to grow and survive even under high loads. The measured heterotrophic bacteria in the substrate and rhizomes indicated the biofilm development and the oxidation of organic matter and nitrogen. Water losses via evapotraspiration were also measured and reached 14%. Overall, the tested CW design proved to be a sustainable and feasible alternative for the treatment of tannery wastewater in tropical climates.

Assuntos

RESUMO

The removal of toxic compounds (azo dyes) from dyeing wastewater was investigated by an environmentally friendly activated carbon produced from solid waste generated in the tannery process, the cattle hair (CHW), activated with H3PO4 (AC-CHW), suggesting a life cycle extension for this material from leather processing. Preliminary tests with aqueous solutions containing Acid Brown 414 (AB-414) and Acid Orange 142 (AO-142) removed 71.06% and 73.05%, respectively. The activated carbon was characterized by zeta potential (ZP), functional groups (FTIR), elemental composition, sorbent specific surface area, and pore size distribution (BET/BJH). The specific surface area showed low values when compared to commercial activated carbon, but average pore diameter was higher, which facilitates the adsorption of larger and complex molecules, such as those present in real wastewaters. Through SEM and FTIR, the presence of the toxic compounds studied in the AC-CHW after sorption process was observed, where the results indicated that the functional groups of -CH=CH- participated in the removal process for these compounds. The removal efficiency obtained with AC-CHW was 51.94% and 49.73% for the dyeing wastewater containing AB-414 and AO-142, respectively. The obtained results open a promising via to use AC-CHW as efficient eco-friendly sorbent for the treatment of leather wastewater.

Assuntos

RESUMO

Abstract Wastewater generated in tanneries have essential elements for microalgae growth, but it has also some toxic compounds that may hinder or restrain the growth of microalgae in this environment. This work tested microalgae consortium growth originating from a deactivated effluent treatment decanter of a complete tannery (beamhouse to finished leather) for the treatment of wastewater of a tannery processing wet-blue leather to finished leather. It was initially evaluated the growth of the microalgae consortium in the three effluents diluted in 50% distilled water: raw effluent (50RE50W), effluent after primary coagulation/flocculation (50PE50W), and effluent after primary and secondary biological treatment (50BE50W). After 16 days of cultivation, the 50PE50W presented the highest biomass concentration (1.77 g L−1). The highest removal values for effluents 50RE50W, 50PE50W and 50BE50W were 51.02%, 99.90%, 82.88%, and 91.75% for chemical oxygen demand (COD), N-NH3, TKN, and P-PO4-, respectively. It was verified low levels of nutrient removal in the raw effluent (100RE), since the consortium was not able to grow in this medium. Finally, at concentrations of 25RE75BE (25% raw effluent diluted with 75% effluent after the biological treatment) and 50RE50B (50% raw effluent diluted with 50% effluent after the biological treatment), effective removal values were reached. Biomass growth concentration up to 1.3 g L-1 and removal values for N-NH3, TKN, P-PO4, COD, total organic carbon (TOC) and biological oxygen demand (BOD5), of 99.90%, 79.36%, 87.82%, 14.26%, 35.82%, and 42.86%, respectively, were reached in 50RE50B.

Assuntos

RESUMO

Although the toxic effects of tannery effluent (TE) on tanning-industry workers have been reported in many studies, its effects on females' reproductive system are unknown. We aimed at evaluating the effects of direct contact with TE on the "emotional" status, estrous cycle (during 15 consecutive exposure days), and ovarian follicular dynamics of female Swiss mice at the end of the experiment to broaden the knowledge about the toxicity of this pollutant. The herein adopted exposure protocol simulated tanning-industry workers' exposure to TE. The test animals were subjected to 45 exposure days, for 1 h a day, 5 days a week (from Monday to Friday). Based on the collected data, female mice exposed to TE recorded high anxiety index in the elevated plus maze test, although we did not observe changes in their estrous cycle. The smaller total and specific number of ovarian follicles (types 1 to 6) and the higher frequency of degenerating follicles (atresic) in female mice exposed to TE marked the folliculogenesis reduction in them. Therefore, our study was the first to provide evidences that the exposure to TE can cause reproduction issues in female mice, as well as the first experimental insight about the impact of unhealthy work activities in tanning industries on women's reproductive system.

Assuntos

RESUMO

Tannery industries are considered highly polluting due to the large production of polluted wastewater [untreated tannery effluent (UTE)]. Although previous studies have already shown the consequences from fish, birds and mammals' exposure to this pollutant, little is known about its toxicological effect on representatives of class amphibian. Thus, we aim at assessing whether short-term UTE exposure, even at low concentrations (0.2% UTE diluted in water), would be able to induce behavioral, morphological and cyto-genotoxic changes in L. catesbeianus tadpoles. In order to do so, two experimental groups were set (control and tannery effluent) and exposed, or not, to UTE for seven days. A positive control group (cyclophosphamide) was included in the experimental design in order to assess cyto-genotoxicity. Our behavioral results showed that tadpoles exposed to the contaminant presented abnormal responses in the predator-response test; therefore, it evidenced losses in their capacity to recognize chemical olfactory cues of a potential predator. We also searched for changes in mouth length, in dentition, in body length before and after the eyes of animals exposed to UTE. Besides, we observed higher nuclear abnormality frequency in the circulating erythrocytes of tadpoles exposed to the contaminant, as well as in animals belonging to the positive control group. Some of the observed abnormalities were micronuclei, binucleated, notched, kidney-shaped and blebbed cells, multilobulated nuclei, as well as lower mitotic index. Therefore, our data confirm the hypothesis that UTE causes behavioral, morphological and cyto-genotoxic changes in L. catesbeianus tadpoles, fact that opens new perspectives to other investigations about how and which UTE constituents were responsible for the observed effects.

Assuntos