RESUMO

Ethylene is a plant hormone regulator that stimulates chlorophyll loss and promotes softening and aging, resulting in a deterioration and reduction in the post-harvest life of fruit. Commercial activated carbons have been used as ethylene scavengers during the storage and transportation of a great variety of agricultural commodities. In this work, the effect of the incorporation of copper oxide over activated carbons obtained from baru waste was assessed. Samples were characterized by X-ray diffraction (XRD), N2 adsorption-desorption at -196 °C, field-emission scanning electron microscopy (FESEM) coupled with energy-dispersive X-ray spectroscopy (EDS), and infrared (IR) spectroscopy. The results showed that the amount of ethylene removed using activated carbon obtained from baru waste and impregnated with copper oxide (1667 µg g-1) was significantly increased in comparison to the raw activated carbon (1111 µg g-1). In addition, carbon impregnated with copper oxide exhibited better adsorption performance at a low ethylene concentration. Activated carbons produced from baru waste are promising candidates to be used as adsorbents in the elimination of ethylene during the storage and transportation of agricultural commodities at a lower cost.

RESUMO

Capacitive deionization (CDI) is an emerging water desalination technology whose principle lies in ion electrosorption at the surface of a pair of electrically charged electrodes. The aim of this study was to obtain the best performance of a CDI cell made of activated carbon as the active material for water desalination. In this work, electrodes of different active layer thicknesses were fabricated from a slurry of activated carbon deposited on graphite sheets. The as-prepared electrodes were characterized by cyclic voltammetry, and their physical properties were also studied using SEM and DRX. A CDI cell was fabricated with nine pairs of electrodes with the highest specific capacitance. The effect of the flow rate on the electrochemical performance of the CDI cell operating in charge-discharge electrochemical cycling was analyzed. We obtained a specific absorption capacity (SAC) of 10.2 mg/g and a specific energetic consumption (SEC) of 217.8 Wh/m3 at a flow rate of 55 mL/min. These results were contrasted with those available in the literature; in addition, other parameters such as Neff and SAR, which are necessary for the characterization and optimal operating conditions of the CDI cell, were analyzed. The findings from this study lay the groundwork for future research and increase the existing knowledge on CDI based on activated carbon electrodes.

RESUMO

In this contribution, we present a study of the mechanical properties of porous nanoshells measured with a nanoindentation technique. Porous nanoshells with hollow designs can present attractive mechanical properties, as observed in hollow nanoshells, but coupled with the unique mechanical behavior of porous materials. Porous nanoshells display mechanical properties that are dependent on shell porosity. Our results show that, under smaller porosity values, deformation is closely related to the one observed for polycrystalline and single-crystalline nanoshells involving dislocation activity. When porosity in the nanoparticle is increased, plastic deformation was mediated by grain boundary sliding instead of dislocation activity. Additionally, porosity suppresses dislocation activity and decreases nanoparticle strength, but allows for significant strain hardening under strains as high as 0.4. On the other hand, Young's modulus decreases with the increase in nanoshell porosity, in agreement with the established theories of porous materials. However, we found no quantitative agreement between conventional models applied to obtain the Young's modulus of porous materials.

RESUMO

A thermally stable carbocationic covalent organic network (CON), named RIO-70 was prepared from pararosaniline hydrochloride, an inexpensive dye, and triformylphloroglucinol in solvothermal conditions. This nanoporous organic material has shown a specific surface area of 990 m2 g-1 and pore size of 10.3 Å. The material has CO2 uptake of 2.14 mmol g-1 (0.5 bar), 2.7 mmol g-1 (1 bar), and 6.8 mmol g-1 (20 bar), the latter corresponding to 3 CO2 molecules adsorbed per pore per sheet. It is shown to be a semiconductor, with electrical conductivity (σ) of 3.17×10-7  S cm-1 , which increases to 5.26×10-4  S cm-1 upon exposure to I2 vapor. DFT calculations using periodic conditions support the findings.

RESUMO

Recently, tissue engineering and regenerative medicine studies have evaluated smart biomaterials as implantable scaffolds and their interaction with cells for biomedical applications. Porous materials have been used in tissue engineering as synthetic extracellular matrices, promoting the attachment and migration of host cells to induce the in vitro regeneration of different tissues. Biomimetic 3D scaffold systems allow control over biophysical and biochemical cues, modulating the extracellular environment through mechanical, electrical, and biochemical stimulation of cells, driving their molecular reprogramming. In this review, first we outline the main advantages of using polysaccharides as raw materials for porous scaffolds, as well as the most common processing pathways to obtain the adequate textural properties, allowing the integration and attachment of cells. The second approach focuses on the tunable characteristics of the synthetic matrix, emphasizing the effect of their mechanical properties and the modification with conducting polymers in the cell response. The use and influence of polysaccharide-based porous materials as drug delivery systems for biochemical stimulation of cells is also described. Overall, engineered biomaterials are proposed as an effective strategy to improve in vitro tissue regeneration and future research directions of modified polysaccharide-based materials in the biomedical field are suggested.

Assuntos

RESUMO

A facile and greener methodology to obtain pure chitosan-based 3D porous structures in the form of monoliths and films is proposed. It is based on a modified evaporation-induced phase separation process in a chitosan solution precursor. In this approach, a deep eutectic solvent (DES) is used as the nonsolvent system and an ecofriendly, cost effective, simple and versatile alternative for the production of highly structured chitosan materials. The porous heterogeneous structure can be fine-tuned by varying the chitosan content in the precursor solution and chitosan/DES ratio, and enabled the structured polymer to absorb large amounts of water to form hydrogels. This is a versatile and unexplored approach to design porous chitosan with tailored morphology in the absence of crosslinkers, which, based on preliminary studies on V. cholerae biofilm formation, is expected to open new avenues for various applications in biomedical, catalysis, water purification, filtration and other areas where the control of bacterial biofilm formation is critical.

Assuntos

RESUMO

Activated carbons are well-known porous materials as an effective adsorbent used for the removal of emerging contaminants, such as herbicides, which are increasingly present in water bodies. Most water treatment plants, specially in Brazil, are unable to completely remove such contaminants by the conventional process and advanced treatment using activated carbons is required. The aim of this paper was to verify the influence of the activated carbons granulometry and specific surface area on the 2,4-dichlorophenoxyacetic acid (2,4-D) herbicide removal efficiency using distilled-deionized water and filtered water collected from a conventional Water Treatment Plant. Commercial activated carbons samples used in this work were obtained from two different manufacturers. Activated carbons were analyzed by the specific surface area, pore size and volume distribution, nuclear magnetic resonance, infrared and x-ray spectroscopy, moisture, volatile matter and ash contents. Batch adsorption isotherms experiments were used and performed by Langmuir and Freundlich models. Granular and powdered activated carbons removed over 99% of 2,4-D in distilled water and near to 99% using filtered water. The activated carbons evaluated in this work presented high performance and played a key role in water treatment by removing 2,4-D herbicide, ensuring the protection of human health and the ecosystem.

Assuntos

RESUMO

Sustainability in chemistry heavily relies on heterogeneous catalysis. Enzymes, the main catalyst for biochemical reactions in nature, are an elegant choice to catalyze reactions due to their high activity and selectivity, although they usually suffer from lack of robustness. To overcome this drawback, enzyme-decorated nanoporous heterogeneous catalysts were developed. Three different approaches for Candida antarctica lipase B (CAL-B) immobilization on a covalent organic framework (PPF-2) were employed: physical adsorption on the surface, covalent attachment of the enzyme in functional groups on the surface and covalent attachment into a linker added post-synthesis. The influence of the immobilization strategy on the enzyme uptake, specific activity, thermal stability, and the possibility of its use through multiple cycles was explored. High specific activities were observed for PPF-2-supported CAL-B in the esterification of oleic acid with ethanol, ranging from 58 to 283 U mg-1 , which was 2.6 to 12.7 times greater than the observed for the commercial Novozyme 435.

Assuntos

RESUMO

The electrical characterization of catalysts composed of layered manganese oxide in the form of birnessite supported on γ-Al2O3, which have been successfully used in the combustion of soot, is presented. The results indicate that the electrical conduction and ion conduction processes are influenced by the amount of the active phase. There was also evidence of Grotthuss-type proton conductivity favored by the presence of surface water on the exposed alumina surface. The above is supported by the porous nature of the catalyst in which the surface area varied between 125.2 ± 1.2 and 159.0 ± 1.1 m2/g, evidencing changes in the alumina surface. The conductivity, determined from measurements of impedance spectroscopy, at low frequency showed changes associated with the amount of the active phase. The values ranged from 2.61 × 10-8 ± 2.1 × 10-9 Ω-1·cm-1 (pure alumina) to 7.33 × 10-8 ± 5.9 × 10-9 Ω-1·cm-1, 7.21 × 10-8 ± 5.8 × 10-9 Ω-1·cm-1 and 4.51 × 10-7 ± 3.6 × 10-8 Ω-1·cm-1 at room temperature for catalysts with nominal active phase contents of 5.0, 10.0 and 20.0%, respectively. Such results indicate that it is possible to modulate the electrical properties with variations in the synthesis parameters.

Assuntos

RESUMO

Chondroitin sulfate (ChS), a sulfated glycosaminoglycan, poly(vinyl alcohol) (PVA) and bovine bone powder (BBP) were blended to form a novel eco-friendly biocomposite through cyclic freeze-thawing under mild conditions. The systematic investigation reveals that the content of BBP has a remarkable effect on the pore size, porosity, mechanical and liquid uptake properties and biodegradability. At 10wt.% BBP the biocomposite exhibited enhanced mechanical properties and biodegradability rate as compared to the pristine sample. Further, different properties of the biocomposite can be tailored according to the content of BBP. In vitro assays showed that ChS/PVA-BBP does not exert cytotoxicity against healthy cells. In vivo and ex vivo experiments revealed that ChS/PVA-BBP biocomposites are biocompatibility materials without exert pro-inflammatory responses. The biocomposite was completely biodegraded and bioresorbed after 15days of treatment. Taken together, BBP is a low-cost source of hydroxyapatite and collagen, which are insurance. All these results suggest that the biocomposite designed in this study is a promising biomaterial for potential skin tissue engineering.

Assuntos

RESUMO

Metal-free catalysts are of great importance and alternative candidates to conventional metal-based catalysts for many reactions. Herein, several types of metal-organic frameworks have been exploited as templates/precursors to afford porous carbon materials with various nitrogen dopant forms and contents, degrees of graphitization, porosities, and surface areas. Amongst these materials, the PCN-224-templated porous carbon material optimized by pyrolysis at 700 °C (denoted as PCN-224-700) is composed of amorphous carbon coated with well-defined graphene layers, offering a high surface area, hierarchical pores, and high nitrogen content (mainly, pyrrolic nitrogen species). Remarkably, as a metal-free catalyst, PCN-224-700 exhibits a low activation energy and superior activity to most metallic catalysts in the catalytic reduction of 4-nitrophenol to 4-aminophenol. Theoretical investigations suggest that the content and type of the nitrogen dopant play crucial roles in determining the catalytic performance and that the pyrrolic nitrogen species makes the dominant contribution to this activity, which explains the excellent efficiency of the PCN-224-700 catalyst well.

RESUMO

O presente trabalho teve como objetivo avaliar volumetricamente a presença de poros em três cimentos obturadores. Para a análise de porosidade, quatro cilindros de cada cimento foram preparados e escaneados usando um microtomógrafo de alta resolução (Skyscam 1174, Kontich, Bélgica). O cálculo da porosidade foi realizado por meio de análise de imagens digitalizadas dos blocos de cimentos. Os quais foram microtomografados para criação de modelos tridimensionais. A presença de poros e vacúolos foi então avaliada por inferência do software CT analiser®. Os resultados mostraram que o i-Root SP teve o menor índice de porosidade (0,07%), enquanto o AH plus e o MTA Fillapex não apresentaram diferenças estatisticamente significativas entre si (p≥0,05). Apesar dos resultados para o índice de porosidade total do MTA Fillapex e do AH plus não terem diferenças significativas(p>0,05), os achados do presente trabalho mostraram que o MTA fillapex obteve resultados significativamente maiores nos volumes médios individuais dos poros internos que o Ah plus e o i-Root SP. Os resultados foram tabulados e analisados estatisticamete através do teste Anova ao nível de significância de 5%

This study aimed to evaluate the presence of pores volumetrically in three sealers. For the analysis of porosity, four-cylinder of each cement were prepared and scanned using a high resolution Micro-CT scanner (Skyscam 1174, Kontich, Belgium). The porosity calculation was performed by analysis of digitized images of cement blocks. Which were scanned for creating three-dimensional models. The presence of pores and vacuoles was then evaluated by inference software CT Analiser ®. The results showed that the i-Root SP had the lowest porosity index (0.07%), while the AH Plus and MTA Fillapex showed no statistically significant differences between groups (p ≥ 0.05). Although the results for the index of total porosity Fillapex MTA and AH Plus did not have significant differences (p> 0.05), the findings of this study showed that the MTA fillapex scored significantly higher in the average volume of individual internal pores that Oh the plus and i-Root SP. The results were tabulated and analyzed estatisticamete by ANOVA at a significance level of 5%

Assuntos