RESUMO

The reuse of by-products has become increasingly important as a means of minimising the consumption of natural resources and reducing waste disposal. This study examines the potential reuse of steel slag for soil stabilisation, with benefits such as conserving natural resources and mitigating the greenhouse gas emissions associated with the production of conventional stabilising agents. It focuses on evaluating the effect of pozzolanic reactions on the strength and stiffness of both loess silt and silt-bentonite mixtures. The experimental tests included the physical characterisation of granular materials, reactivity tests of the pozzolanicity of soil mixtures, compaction tests, unconfined compression tests, and hydraulic conductivity tests. The impact of the curing period was also analysed to quantify the effects of natural cementation and the development of hydrogels within soil pores on the compacted soil properties. The findings suggest that adding steel slag can significantly increase the strength and the stiffness of compacted loess silts by over 300% and 500%, respectively, after 56 days of curing, substantially reducing the hydraulic conductivity of granular materials, such as the tested silt, as hydrogels partially occupy the pores available for liquid flow. It should be noted that the chemical reactions during hydrogel formation may hinder the free expansion of clay mixtures and release Ca2+ ions, thereby counteracting the expected reduction in hydraulic conductivity when bentonite is added to compacted earthen barriers.

RESUMO

Enhanced phosphorus management, geared towards sustainability, is imperative due to its indispensability for all life forms and its close association with water bodies' eutrophication, primarily stemming from anthropogenic activities. In response to this concern, innovative technologies rooted in the circular economy are emerging, to remove and recover this vital nutrient to global food production. This research undertakes an evaluation of the dead-end filtration performance of a mixed matrix membrane composed of modified bentonite (MB) and polyvinylidene fluoride (PVDF) for efficient phosphorus removal from water media. The MB:PVDF membrane exhibited higher permeability and surface roughness compared to the pristine membrane, showcasing an adsorption capacity (Q) of 23.2 mgP·m-2. Increasing the adsorbent concentration resulted in a higher removal capacity (from 16.9 to 23.2 mgP·m-2) and increased solution flux (from 0.5 to 16.5 L·m-2·h-1) through the membrane. The initial phosphorus concentration demonstrates a positive correlation with the adsorption capacity of the material, while the system pressure positively influences the observed flux. Conversely, the presence of humic acid exerts an adverse impact on both factors. Additionally, the primary mechanism involved in the adsorption process is identified as the formation of inner-sphere complexes.

Assuntos

RESUMO

As a part of the mission to create materials that are more environmentally friendly, we present the following proposal, in which a study of the mechanical properties of composite materials comprising a polyester resin with sisal fiber and bentonite particles was conducted. Sisal fiber was added to a matrix in percentages ranging from 5% to 45% in relation to the polyester resin weight, while bentonite remained fixed at 7% in relation to the polyester resin weight. The specimens were manufactured by compression molding. The mechanical properties were analyzed by tensile, bending, impact, stepped creep, and relaxation tests. In addition, energy-dispersive X-ray spectroscopy and scanning electron microscopy analyses were carried out to analyze the composition and heterogeneity of the structure of the composite material. The results obtained showed that 7% of bentonite added to the matrix affects the tensile strength. Flexural strength increased by up to 21% in the specimens with a 20% addition of sisal fiber, while the elastic modulus increased by up to 43% in the case of a 20% addition of sisal fiber. The viscoelastic behavior was improved, while the relaxation stress was affected.

RESUMO

Nanofertilizers could promote nutrient efficiency with slow release compared to conventional fertilizers (CF). Most of the applied nitrogen is lost on the soil by leaching, due to the rapid release behavior of CF. Clays can function as a nanosized porous structure to retain and slowly release nutrients. The objective of this study was to evaluate a nitrogenous nanocomposite (NCN) and its effect on leaching and N content of lettuce (Lactuca sativa). The treatments applied were: 100% conventional fertilizer, 100% nitrogenous nanocomposite and the mixture in percentage of CF/NCN 25/75, 50/50, 75/25 and 25/0, 50/0 75/0% on columns of soil with lettuce for 45 days. Leachates at the end of the cycle increased in treatments with NCN. Treatments with NCN have higher N content in the leaf. In regard to biomass growth, leaf area, leaf N, drained variables, electrical conductivity and NO3- content, it was possible to show that the doses of 50 and 75% of NCN match the characteristics of the crop compared to the control, which allows us to use lower doses than those recommended with CFs.

RESUMO

L-ascorbic acid (LAA), commonly known as vitamin C, is an excellent and recognized antioxidant molecule used in pharmaceutical and cosmetic formulations. Several strategies have been developed in order to preserve its chemical stability, connected with its antioxidant power, but there is little research regarding the employment of natural clays as LAA host. A safe bentonite (Bent)-which was verified by in vivo ophthalmic irritability and acute dermal toxicity assays-was used as carrier of LAA. The supramolecular complex between LAA and clay may constitute an excellent alternative, since the molecule integrity does not seem to be affected, at least from the point of view of its antioxidant capacity. The Bent/LAA hybrid was prepared and characterized through ultraviolet (UV) spectroscopy, X-ray diffraction (XRD), infrared (IR) spectroscopy, thermogravimetric analysis (TG/DTG) and zeta potential measurements. Photostability and antioxidant capacity tests were also performed. The LAA incorporation into Bent clay was demonstrated, as well as the drug stability due to the Bent photoprotective effect onto the LAA molecule. Moreover, the antioxidant capacity of the drug in the Bent/LAA composite was confirmed.

RESUMO

The influence of the addition of bentonite nanoparticles on the tensile and flexural strength of a thermosetting polymer matrix composite material reinforced with hemp fibers was de-terminated. All composites were manufactured with 5% of bentonite in the polymer mass-weight ratios and 10 to 45 wt% of fibers with a step of 5%. For mechanical characterization, tensile and flexural tests were performed: scanning electron microscopy and energy-dispersive X-ray spectroscopy analyses were carried out. The tensile strength of the samples containing bentonite compared to the polymer samples with the fiber addition was affected for all fiber addition percentages, except for 35% while the flexural resistance improved with the addition of bentonite in the percentages of 20, 30, 35, and 45% of fiber addition. With the addition of bentonite, the maximum values of tensile and flexural strength were both obtained for the 35% addition of fibers, with values of 34.28 MPa and 98.04 MPa, respectively. The presence of bentonite favored the rigidity of the material to traction and bending, which was reflected through an increase in the elastic modulus compared to the composite that only had fiber. The maximum values obtained were 9065 MPa in tension and 8453 MPa in flexion for the 40% and 35% of addition of fiber, respectively. Microscopy showed a good distribution of fibers in the matrix, the absence of internal porosities, and a good interaction between matrix and reinforcement.

RESUMO

Anthocyanins are one of the natural pigments that humanity has employed the most and can substitute synthetic food dyes, which are considered toxic. They are responsible for most purple, blue, and red pigment nuances in tubers, fruits, and flowers. However, they have some limitations in light, pH, oxygen, and temperature conditions. Combining biomolecules and inorganic materials such as clay minerals can help to reverse these limitations. The present work aims to produce materials obtained using cetyltrimethylammonium bromide in bentonite clay for incorporation and photostabilization of anthocyanin dye. Characterizations showed that the organic molecules were intercalated between the clay mineral layers, and the dye was successfully incorporated at a different pH. Visible light-driven photostability tests were performed with 200 h of irradiation, confirming that the organic-inorganic matrices were efficient enough to stabilize the quinoidal base form of anthocyanin. The pigment prepared at pH 10 was three-fold more stable than pH 4, showing that the increase in the synthesis pH promotes more stable colors, probably due to the stronger intermolecular interaction obtained under these conditions. Therefore, organobentonite hybrids allow to stabilize the fragile color coming from the quinoidal base form of anthocyanin dyes.

Assuntos

RESUMO

Bentonite was applied in diffusive studies for selenium, an emerging contaminant. The planar source method was used to determine the apparent and effective diffusion coefficients and assess the mobility of the selenium species. A double Gaussian function described the results. Different diffusion coefficients were associated with different mobilities, and consequently, to the coexistence of two selenium species: selenite and selenate. Apparent diffusion coefficients were higher for selenate, around 10- 10 m2 s- 1, than for selenite, around 10- 12 m2 s- 1. Results from sequential extraction and distribution coefficient justified selenate's greater mobility than selenite. Since the increase in redox potential from 448 to 511 mV may be associated with selenite oxidation in an interconversion process, the diffusion in bentonite demonstrates that applications in geological barriers deserve attention regarding the mobilization of selenium species. Interconversions can mobilize selenium, as reduced species can shift to more oxidized and mobile species, enhancing environmental contamination.

Assuntos

RESUMO

Waste rock from bentonite mining (WRBM) was evaluated as potential adsorbents for removing crystal violet (CV) and methylene blue (MB) cationic dyes from contaminated water. The waste samples (AM01, AM02, and AM03) were collected from different locations of the bentonite mine and characterized through X-ray diffraction, X-ray fluorescence, Fourier-transform infrared spectroscopy, N2 adsorption/desorption, and cation exchange capacity. The adsorption efficiency of CV and MB dyes was investigated through the effect of initial concentration, contact time, pH, the dosage of adsorbent, and temperature. Sample AM02 showed the largest surface area (69.13 m2/g) and the best adsorptive performance for both dyes, with removal more significant than 90%. The adsorption of CV and MB in the waste followed the Langmuir isothermal model. Samples AM01 and AM02 followed the pseudo-second-order (PSO) kinetic model, while AM03 better fitted the Elovich kinetic model. The enthalpy (ΔH), entropy (ΔS), and Gibbs energy (ΔG) were evaluated as adsorption parameters. The process of adsorption of CV and MB dyes in the waste was predominantly endothermic and occurred spontaneously. WRBM samples proved to be a promising candidate for removing cationic dyes present in water.

Assuntos

RESUMO

The objective of this work was to obtain biomaterials as gelatin films or biofilms produced by casting, reinforced with a microfiber (MF) from Agave angustifolia Haw bagasse and bentonite (BN) nanoparticles and evaluate the effect of such reinforcements at different concentrations. Agave microfibers were obtained by a non-abrasive chemical method. Three formulations based on gelatin with glycerol were reinforced with microfiber, bentonite and both materials with 1.5, 3.5 and 5.5% w/w solids content. Physicochemical properties were determined using SEM and FTIR, thickness, soluble matter and moisture. The XRD, barrier, mechanical and thermal properties were measured. The films' micrographs showed agglomerations on the surface. Interactions between its functional groups were found. The solubility increased when the MF concentration increased. The thickness of the films was between 60 and 110 µm. The crystallinity ranged from 23 to 86%. The films with both MF and BN and 3.5% w/w solids had the lowest barrier properties, while the film with 5.5% w/w solids showed the highest mechanical properties, being thermally resistant. Overall, Agave microfibers together with bentonite were able to improve some of the films' properties, but optimized mixing conditions had to be used to achieve good particle dispersion within the gelatin matrix to improve its final properties. Such materials might have the potential to be used as food packaging.

RESUMO

In this work, calcium alginate hydrogels with natural and pillared bentonites (0.5 and 5% w/w) were synthetized in two geometries (disks and beads) and their capacity to adsorb cadmium ion from aqueous media was evaluated. Pillarization effect on bentonite morphology was evidenced by SEM, XRD, LD and BET isotherms. Structure and swelling capacity of hydrogels were determined, showing that hydrogels beads with pillared clays presented the higher ability to retain water. Regarding cadmium adsorption capacity, the effect of pH media (3, 5 and 7), the contact time (0 to 320 min.) and the initial cadmium ion concentration (6 to 42 mg/L) were studied employing hydrogel beads. Regardless bentonite type and concentration, the optimal pH cadmium adsorption was 7, reaching the highest adsorption capacity (93%) for hydrogel with 0.5% natural bentonite. Besides, the equilibrium adsorption time was reached at 120 min for all studied hydrogels and experimental data fitted with a pseudo-second order kinetic model.

Assuntos

RESUMO

Contamination of water with arsenic is a major global health problem. The use of adsorbent materials for the removal of As from aqueous systems is a plausible solution to this problem. In this work, the use of commercial bentonites (purified and modified with iron (III)) for the removal of As from water was studied. The samples were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier Transformed Infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and nitrogen adsorption/desorption isotherms to determine their physicochemical properties. The arsenic removal capacities of adsorbent materials were studied from 1 mg/L solutions of As (III) using the colorimetric technique of molybdenum blue. High adsorption capacity (0.33 mg/g) of As (III) was obtained in aqueous systems after 1 h of treatment with unmodified bentonite. The incorporation of iron improved the removal performance in short times. The obtained results could be the starting point for the development of a low-cost filtration system that contributes to solve the problem of arsenic in water.

Assuntos

RESUMO

Worldwide, freshwater environments are impacted by inputs of nutrients and dissolved organic matter from human activities. Yet, the recovery of aquatic systems is usually focused only on nutrient management. In our work, we presented the case of an urban and hypereutrophic environment (Pampulha reservoir, Belo Horizonte, Brazil) that receives discharges from several streams and was treated with lanthanum modified bentonite (Phoslock®) and microbial bioremediation (Enzilimp®). Our goals were to evaluate whether the treatment could improve the water quality and characterize the spatiotemporal variation of dissolved organic matter sources and indices according to absorbance and fluorescence measurements from the reservoir and streams post-application months (2018). In our results, the reservoir showed a relative decrease in its phosphorus concentration compared to data from before the treatment. On the other hand, carbon concentrations reached expressive values in the post-application months following a similar pattern found in the streams. Our data showed that the reservoir's high resistance in its hypereutrophic condition was related to the elevated loading of external inputs coming from the streams. The parallel factor analysis (PARAFAC) identified four main carbon sources, two of them being potential tracers of organic pollution in the Pampulha reservoir and watershed, together with absorbance and fluorescence indices. Our findings suggest that carbon parameters can be essential tools to provide adequate monitoring and optimization of water recovery attempts in complex, polluted environments.

Assuntos

RESUMO

Soil is the base of any ecosystem since it conserves nutrients and water for plant roots including agriculture and plantations. In dry and semi-arid places across the world, including the UAE, sandy soils are common. Their fertility is extremely low, and production is hampered by a number of agronomic challenges. Soil conditioner sources like bentonite and chicken manure might be used to improve the poor sandy soil attributes and hence boost soil productivity. From November 2019 to March 2020, an experiment was conducted to investigate the growth rates of Bougainvillea following bentonite and chicken manure amendments to sandy soil taken from Lehbab, Dubai. Bougainvillea was evaluated for its plant height (cm), max length of primary branch (cm), the number of leaves per plant, number of secondary branches, shoot weight (g), root length (cm), root weight (g), root/shoot ratio, chlorophyll contents, and chlorophyll a* and b*. In this experiment, a complete randomized design (CRD) with five treatments was used (10 replications per treatment). According to the findings, bentonite and chicken manure additions considerably influence the productive properties of sandy soil, as indicated by Bougainvillea growth. Additionally, the research suggests that Bougainvillea may be efficiently planted with 10% bentonite and 15% chicken manure applied to sandy soil, resulting in the healthiest plants compared to other amendments.

O solo é a base de qualquer ecossistema, incluindo agricultura e plantações, pois conserva nutrientes e água para as raízes das plantas. Em lugares secos e semiáridos em todo o mundo, incluindo os Emirados Árabes Unidos, os solos arenosos são comuns. Sua fertilidade é extremamente baixa e a produção é prejudicada por uma série de desafios agronômicos. Fontes de condicionador de solo, como bentonita e esterco de galinha, podem ser usadas para melhorar os atributos do solo arenoso pobre e, portanto, aumentar a produtividade do solo. De novembro de 2019 a março de 2020, foi realizado um experimento para investigar as taxas de crescimento de buganvílias após bentonita e esterco de galinha em solo arenoso retirado de Lehbab, Dubai. A buganvília foi avaliada quanto à altura da planta (cm), comprimento máximo do ramo primário (cm), número de folhas por planta, número de ramos secundários, peso da parte aérea (g), comprimento da raiz (cm), peso da raiz (g), razão raiz/parte aérea, teores de clorofila e clorofila a* e b*. Neste experimento foi utilizado o delineamento inteiramente casualizado (DIC) com cinco tratamentos (10 repetições por tratamento). De acordo com os resultados, as adições de bentonita e esterco de galinha influenciam consideravelmente as propriedades produtivas do solo arenoso, conforme indicado pelo crescimento de buganvílias. Além disso, a pesquisa sugere que a buganvília pode ser plantada com eficiência com 10% de bentonita e 15% de esterco de galinha aplicado em solo arenoso, resultando, assim, em plantas mais saudáveis em comparação com outras alterações.

Assuntos

RESUMO

This study investigated the influence of cation type on the sodium deactivation of Brazilian bentonite varieties. Four bentonite clays were studied, including three mixed-cationic and one magnesium. Swelling and the main exchangeable cations (Na+, K+, Mg2+ and Ca2+) were the main evaluation parameters in this study. Periodic washes of the sodium-activated bentonites were performed based on the hypothesis that a possible desorption of the cations (primarily Na+) could cause the deactivation. Sodium activation was monitored using XRD measurements and an increase in swelling. Sodium deactivation was observed and monitored via a decrease in swelling. Positive and negative effects, caused by the proportions of the cations and the dominance of Mg2+, were emphasized by the set of cationically different samples applied in this study, which helped to answer the influence of main exchangeable cations, specially Mg2+, on the deactivation process.

RESUMO

In this work, the reduction of the moisture content from waste oils by a bentonite-based adsorption process was investigated as an alternative for reuse in energy production. Waste cooking oil (WCO) and waste poultry fat (WPF) were characterised (moisture and viscosity, values of acidity, saponification, and peroxide), as well as bentonite clay adsorbent. The response surface methodology (RSM) was applied to define the best moisture adsorption condition by bentonite-based adsorbent regarding a full factorial experimental design (FFED). In the framework of RSM, the adsorbent mass, oil acidity, and agitation speed were varied in three levels in the range of 1.5-3.0 g, 1-38 mgKOH goil-1, and 50-150 rpm, respectively, while the adsorption time was fixed in 24 h. Under the best moisture adsorption condition, kinetic tests were performed in a 1-24 h contact time range, besides performing equilibrium adsorption tests at 5 h contact time. Around 90% moisture removal was attained with 1.5 g adsorbent, acidity value of 1 mgKOH goil-1, and 50 rpm agitation speed, achieving the equilibrium in 5 h. A multilayer adsorption process, as described by the BET isotherm model, was acting in dried bentonite clay, allowing getting excellent moisture adsorption capacity (∼200 mgwater gBent-1). Therefore, moisture removal from waste oils by a bentonite clay-based adsorption process has provided results that are suitable and recommendable for economically viable biodiesel production.

Assuntos

RESUMO

A novel IDA-LaNDT derivative was able to reach the highest productivity in the biosynthesis of a well-known antitumoral agent called decitabine. However, the combination of two simple and inexpensive techniques such as ionic absorption and gel entrapment with the incorporation of a bionanocomposite such as bentonite significantly improved the stability of this biocatalyst. These modifications allowed the enhancement of storage stability (for at least 18 months), reusability (400 h of successive batches without significant loss of its initial activity), and thermal and solvent stability with respect to the non-entrapped derivative. Moreover, reaction conditions were optimized by increasing the solubility of 5-aza by dilution with dimethylsulfoxide. Therefore, a scale-up of the bioprocess was assayed using the developed biocatalyst, obtaining 221 mg/L·h of DAC. Finally, green parameters were calculated using the nanostabilized biocatalyst, whose results indicated that it was able to biosynthesize DAC by a smooth, cheap, and environmentally friendly methodology.

RESUMO

The efficiency of acid treatment on natural calcium bentonite (natural bentonite) for anionic dye adsorption was investigated using methyl orange (MO) as a probe. Additionally, adsorption experiments were accomplished between the natural bentonite, acidified bentonite, and a cationic dye (methylene blue, MB). Acid functionalization in natural bentonite (RF) was carried out with HCl and H2SO4 acids (RF1 and RF2, respectively). The samples were characterized by chemical analysis, mineralogy, particle size, and thermal behavior with the associated mass losses. The adsorption efficiency of MO and MB dyes was investigated by the effects of the initial concentration of adsorbate (Ci) and the contact time (tc). The acid treatment was efficient for increasing the adsorption capacity of the anionic dye, and the Qmaxexp values measured were 2.2 mg/g, 67.4 mg/g e 47.8 mg/g to RF, RF1 e RF2, respectively. On the other hand, the acid functionalization of bentonite did not significantly modify the MB dye adsorption. The Sips equation was the best fit for the adsorption isotherms. Thus, we found that the acid-functionalized bentonite increases the anionic dye adsorption by up to 8000%. The increased adsorptive capacity of acidified bentonite was explained in terms of electrostatic attraction between the clay surface and the dye molecule.

RESUMO

Exposure of geomaterials to acidic leachates may compromise their structure and functionality due to changes in physicochemical, mineralogical, and hydraulic behavior. The literature identifies the need to evaluate changes in a pure state and in conditions of extreme acidity. This study aimed to evaluate changes in the chemical, mineralogical, and morphological properties of Osorio fine uniform sand (OFS), basalt residual soil (BRS), kaolin (KAO), and bentonite (BEN) exposed to sulfuric acid in concentrations of 0.00 mol/L (distilled water), 0.01 mol/L, and 1.00 mol/L. The tested samples were characterized using X-ray fluorescence spectrometry, X-ray diffraction, thermogravimetry, differential scanning calorimetry, and scanning electron microscopy. The acid attack on geomaterials by contact with the solution 1.00 mol/L has resulted in the solubilization of some constituent minerals, as well as the formation of sulfate minerals, changes in the water dehydration peak in the pores, and mass loss. The morphology of the sand and bentonite particles did not change with exposure to sulfuric acid. The acidic attack resulted in changes in the morphology of the particles for BRS and KAO. The results of this study are important for determining operational parameters of waste containment systems and contaminated areas, as well as for applying geomaterials as founding materials.

Assuntos

RESUMO

In the present study, a novel extracellular laccase isolated from Geobacillus stearothermophilus ATCC 10149 was entrapped in a bionanocomposite matrix consisting of copper alginate (Cu-alginate) supplemented with the nanoclay bentonite. After optimization, this nanobiocatalyst was able to degrade up to 90% of Remazol Brilliant Blue R (RBBR) without the addition of redox mediators and retained 70% of its initial activity for at least 1440 h, equivalent to more than 288 uses. The incorporation of nanoclay allowed alginate beads to be used in alkaline pH and strengthened its mechanical properties. Besides, this thermophilic laccase was able to decolorize other structurally different synthetic dyes such as Methyl Orange, Malachite Green and Indigo Carmine. These preliminary results suggested that the nanobiocatalyst could be a suitable option for dye decolorization and be further developed for large scale bioremediation of toxic dyes.