RESUMO
Gap-graded aggregate combined with asphalt rubber presents a high-performance alternative for roads with heavy traffic loads, offering advantages over conventional mixtures in terms of permanent deformation (rutting), fatigue life, and texture. In this study, the conventional filler in the well-established mixture was substituted with sugarcane bagasse bottom ash (SCBA) at a proportion of 5% of the total mineral aggregates. The objective was to enhance the mechanical performance of the asphalt coating while ensuring proper disposal of this waste material. Compared to conventional filler, SCBA is less dense, has smaller dimensions, and exhibits greater roughness, thereby affecting the volumetric parameters of the Marshall mix design. Consequently, the volume of voids in mineral aggregates and voids filled with asphalt increased while maintaining the same volume of air voids (5.3%). Consequently, there was a notable increase in Marshall Stability (40%) and Indirect Tensile Test (22%) mechanical parameters. Following laboratory analysis, the modified mixtures were applied as asphalt coating on a high-traffic highway (BR-158). Field specimens revealed an 18% increase in the Resilience Modulus (4088 MPa; 3478 MPa). Additionally, its Flow Number exhibited a 73% increase (16,707; 9681), and its permanent deformation rate was 28% lower within 10,000 cycles in the dynamic creep test. This was further supported by an 11% reduction in permanent deformation rate in the Hamburg Wheel Tracking Device (HWTD) within 20,000 cycles (3.2 mm; 3.6 mm). In conclusion, the partial replacement of conventional filler with sugarcane bagasse ash within the established granulometric range has demonstrated technical feasibility both in laboratory and field settings.
RESUMO
Bio-energy systems with carbon capture and storage (BECCS) will be essential if countries are to meet the gas emission reduction targets established in the 2015 Paris Agreement. This study seeks to carry out a thermodynamic optimization and analysis of a BECCS technology for a typical Brazilian cogeneration plant. To maximize generated net electrical energy (MWe) and carbon dioxide CO2 capture (Mt/year), this study evaluated six cogeneration systems integrated with a chemical absorption process using MEA. A key performance indicator (gCO2/kWh) was also evaluated. The set of optimal solutions shows that the single regenerator configuration (REG1) resulted in more CO2 capture (51.9% of all CO2 emissions generated by the plant), penalized by 14.9% in the electrical plant's efficiency. On the other hand, the reheated configuration with three regenerators (Reheat3) was less power-penalized (7.41%) but had a lower CO2 capture rate (36.3%). Results showed that if the CO2 capture rates would be higher than 51.9%, the cogeneration system would reach a higher specific emission (gCO2/kWh) than the cogeneration base plant without a carbon capture system, which implies that low capture rates (<51%) in the CCS system guarantee an overall net reduction in greenhouse gas emissions in sugarcane plants for power and ethanol production.
RESUMO
Contamination with traces of pharmaceutical compounds, such as ciprofloxacin, has prompted interest in their removal via low-cost, efficient biomass-based adsorption. In this study, classical models, a mechanistic model, and a neural network model were evaluated for predicting ciprofloxacin breakthrough curves in both laboratory- and pilot scales. For the laboratory-scale (d = 2.2 cm, Co = 5 mg/L, Q = 7 mL/min, T = 18 °C) and pilot-scale (D = 4.4 cm, Co = 5 mg/L, Q = 28 mL/min, T = 18 °C) setups, the experimental adsorption capacities were 2.19 and 2.53 mg/g, respectively. The mechanistic model reproduced the breakthrough data with high accuracy on both scales (R2 > 0.4 and X2 < 0.15), and its fit was higher than conventional analytical models, namely the Clark, Modified Dose-Response, and Bohart-Adams models. The neural network model showed the highest level of agreement between predicted and experimental data with values of R2 = 0.993, X2 = 0.0032 (pilot-scale) and R2 = 0.986, X2 = 0.0022 (laboratory-scale). This study demonstrates that machine learning algorithms exhibit great potential for predicting the liquid adsorption of emerging pollutants in fixed bed.
Assuntos
Celulose , Ciprofloxacina , Aprendizado de Máquina , Redes Neurais de Computação , Ciprofloxacina/química , Adsorção , Celulose/química , Saccharum/química , Poluentes Químicos da ÁguaRESUMO
Arabinoxylan is a major hemicellulose in the sugarcane plant cell wall with arabinose decorations that impose steric restrictions on the activity of xylanases against this substrate. Enzymatic removal of the decorations by arabinofuranosidases can allow a more efficient arabinoxylan degradation by xylanases. Here we produced and characterized a recombinant Bifidobacterium longum arabinofuranosidase from glycoside hydrolase family 43 (BlAbf43) and applied it, together with GH10 and GH11 xylanases, to produce xylooligosaccharides (XOS) from wheat arabinoxylan and alkali pretreated sugarcane bagasse. The enzyme synergistically enhanced XOS production by GH10 and GH11 xylanases, being particularly efficient in combination with the latter family of enzymes, with a degree of synergism of 1.7. We also demonstrated that the enzyme is capable of not only removing arabinose decorations from the arabinoxylan and from the non-reducing end of the oligomeric substrates, but also hydrolyzing the xylan backbone yielding mostly xylobiose and xylose in particular cases. Structural studies of BlAbf43 shed light on the molecular basis of the substrate recognition and allowed hypothesizing on the structural reasons of its multifunctionality.
Assuntos
Bifidobacterium longum , Celulose , Endo-1,4-beta-Xilanases , Glucuronatos , Glicosídeo Hidrolases , Oligossacarídeos , Saccharum , Xilanos , Oligossacarídeos/química , Oligossacarídeos/metabolismo , Glicosídeo Hidrolases/metabolismo , Glicosídeo Hidrolases/química , Glucuronatos/metabolismo , Glucuronatos/química , Endo-1,4-beta-Xilanases/metabolismo , Endo-1,4-beta-Xilanases/química , Xilanos/metabolismo , Xilanos/química , Saccharum/química , Saccharum/metabolismo , Celulose/química , Celulose/metabolismo , Bifidobacterium longum/enzimologia , Bifidobacterium longum/metabolismo , Hidrólise , Especificidade por Substrato , Proteínas Recombinantes/metabolismo , Proteínas Recombinantes/química , DissacarídeosRESUMO
In Brazil the main feedstock used for ethanol production is sugarcane juice, resulting in large amounts of bagasse. Bagasse has high potential for cellulosic ethanol production, and consolidated bioprocessing (CBP) has potential for lowering costs. However, economic feasibility requires bioprocessing at high solids loadings, entailing engineering and biological challenges. This study aims to document and characterize carbohydrate solubilization and utilization by defined cocultures of Clostridium thermocellum and Thermoanaerobacterium thermosaccharolyticum at increasing loadings of sugarcane bagasse. Results show that fractional carbohydrate solubilization decreases as solids loading increases from 10 g/L to 80 g/L. Cocultures enhance solubilization and carbohydrate utilization compared to monocultures, irrespective of initial solids loading. Rinsing bagasse before fermentation slightly decreases solubilization. Experiments studying inhibitory effects using spent media and dilution of broth show that negative effects are temporary or reversible. These findings highlight the potential of converting sugarcane bagasse via CBP, pointing out performance limitations that must be addressed.
Assuntos
Celulose , Clostridium thermocellum , Saccharum , Solubilidade , Thermoanaerobacterium , Saccharum/química , Celulose/química , Celulose/metabolismo , Thermoanaerobacterium/metabolismo , Clostridium thermocellum/metabolismo , Fermentação , Técnicas de Cocultura , Etanol/metabolismoRESUMO
The aim of the present research is to show the development of a sustainability-oriented lab that teaches adsorption concepts in a virtual environment based on the premise "learning-through-play". Kinetic results in the virtual environment are contrasted to those obtained experimentally when diverse adsorbents prepared from Agave Bagasse (Raw Fibers, Hydrothermal Fibers, and Activated Fibers) were synthesized. Comparison between virtual and real-life experiments involving removal of methylene blue in solution showed that a pseudo-first-order model could describe adsorption kinetics satisfactorily. The study is complemented with a characterization of the adsorbents through SEM, nitrogen adsorption isotherms, FTIR and Raman. In addition, the environmental impact of the synthesis of adsorbents was evaluated through well-known methodologies (GAPI, NEMI, and Eco-Scale), which agree that raw fibers are the most eco-friendly material. This research provides an exciting opportunity to advance our knowledge on developing new technologies for teaching in engineering and to compliment real-life practices that consider environmental impacts with virtual experiments.
Assuntos
Poluentes Químicos da Água , Adsorção , Cinética , Poluentes Químicos da Água/química , Poluentes Químicos da Água/análise , Universidades , Azul de Metileno/química , Laboratórios , Purificação da Água/métodos , Celulose/química , Modelos Químicos , Conservação dos Recursos Naturais/métodosRESUMO
In recent decades, natural fibers have emerged as an alternative to synthetic fibers due to their renewable nature, lower environmental impact, and comparable strength properties. Agave bagasse, a byproduct of agave juice extraction in Mexico, stands out for its potential in various industrial applications, notably biocomposite production. Bagasse is rich in cellulose, along with hemicellulose and lignin. Cellulose is the most suitable to be converted into valuable products, and it is versatile, renewable, and biodegradable. An effective pre-treatment is crucial to enrich its fraction. This study aims to determine the optimal pre-treatment conditions for the agave bagasse. Three different pre-treatments were tested, acid (H2SO4), enzymatic (Cellic® HTec2 enzymatic preparation), and sequence of acid-enzymatic (sulfuric acid and Cellic® HTec2), to determine which pre-treatment got the optimal cellulose fraction increase. The acid pre-treatment was conducted over three time ranges (5, 10, and 15 min) at different acid concentrations (1%, 1.5%, and 2%). Enzymatic reactions were conducted over 24 h, testing three different enzyme concentrations (1.5%, 3%, 4.5%). The sequential pre-treatment utilized the optimal conditions derived from the acid experiments (1.5% H2SO4 for 10 min), followed by enzymatic reactions carried out over three different durations (6, 12, and 24 h). The findings revealed that a 1.5% acid concentration applied for 10 min was the most efficient pre-treatment method. This pre-treatment resulted in a 1.9-fold increase in the cellulose fraction while reducing hemicellulose content by 30%. The hemicellulose reduction was confirmed through Fourier Transform IR spectroscopy (FTIR) analysis, complemented by scanning electron microscopy (SEM) observations highlighting physical alterations in the fiber structure. Furthermore, thermogravimetric analysis (TGA) demonstrated improved thermal stability, suggesting potential use in biocomposites. Future research should evaluate the environmental impact of optimized pre-treatment methods for agave bagasse.
RESUMO
Vinasse and ash from sugarcane bagasse (SCB) are key byproducts in the sugar-energy industry. Vinasse is nutrient-rich but environmentally challenging, while sugarcane bagasse ash (SCBA) offers excellent adsorbent for treating effluents. This work aims to assess the effectiveness of SCBA in removing nitrogen (N) and potassium (K) nutrients from Vinasse. Simulated standard solutions of K2SO4 and (NH4)2HPO4 were used to mimic the nutrient concentrations in Vinasse and optimize experimental parameters such as adsorbent mass and contact time. Kinetic and isotherm models were also applied to elucidate the underlying adsorption mechanisms. Structural, morphological, and thermal analyses revealed the micro-mesoporous and heterogeneous nature of SCBA, primarily composed of SiO2 (quartz and cristobalite). The sorption assessment indicated the ideal conditions involved lower SCBA masses (2.5 g) and 6 h of contact time for the simulated standard solutions. The replicated conditions for Vinasse (at an adjusted sorption time of 24 h) demonstrated nutrient sorption and pH correction of the Vinasse, attributed to the alkaline nature of SCBA. Analysis of the sorption kinetic models for K+ and NH4+ revealed that SCBA interacts diffusively with the environment, not necessarily controlled by adsorption on active sites, indicating non-uniform characteristics. The sorption isotherms for K+ and NH4+ showed the non-linearized Freundlich model was the most suitable, indicating the adsorption sites with varying energy levels and a multilayer sorption process. In conclusion, we successfully demonstrated the sorption of nutrients from Vinasse by SCBA, enhancing the value of these residues and mitigating their environmental impact when used in agricultural applications.
Assuntos
Resíduos Industriais , Saccharum , Celulose/química , Açúcares , Dióxido de Silício , Saccharum/química , AdsorçãoRESUMO
Biomass can be used as an energy source to thermochemical conversion processes to biocrude production. However, the supply and dependence on only one biomass for biocrude production can be an obstacle due to its seasonality, availability, and logistics costs. In this way, biomass waste and agroindustrial residues can be mixture and used as feedstock to the hydrothermal co-liquefaction (co-HTL) process as an alternative to obtaining biocrude. In this sense, the present paper analyzed the biocrude yield influence of the co-HTL from a quaternary unprecedented blend of different biomasses, such as sugarcane bagasse, brewer's spent grain (BSG), sludge from a paper recycling mill (PRM), and microalgae (Chlorella vulgaris). In this way, a simplex lattice design was employed and co-HTL experiments were carried out in a 2000 mL high-pressure stirred autoclave reactor under 275 °C for 60 min, considering 15% of feedstock/water ratio. Significant effects in each feedstock and their blends were analyzed aiming to increase biocrude and biochar yield. It was found that the addition of microalgae is only significant when considered more than 50% into the blend with BSG and PRM sludge to increase biocrude yield.
Assuntos
Carvão Vegetal , Chlorella vulgaris , Microalgas , Saccharum , Esgotos , Celulose , Temperatura , Microalgas/química , Biomassa , Água/química , Biocombustíveis/análiseRESUMO
Sustainability is a core topic for all sectors including geotechnical engineering (e.g., design of foundations, earthworks structures, and pavements for major infrastructure and building projects). Despite being comprised of environmental, economic, and social pillars, most sustainability studies in this area have focused on the first. Furthermore, social impacts and the three pillars integration are little explored. As a result, there is a lack of systemic and holistic assessments of innovative geotechnical alternatives. This research advances in this area by performing a complete sustainability assessment and integration of the environmental, economic, and social pillars of two expansive soil stabilization alternatives: (i) sugar cane bagasse ash combined with hydrated eggshell lime alkali-activated by sodium hydroxide (NaOH) and (ii) Portland cement. Individual analyses were carried out to determine the environmental, economic, and social impacts, and the single sustainability index. Alkali-activated binder dosages showed higher impacts in 4 out of 10 environmental categories. For both binders, high-density/low-binder dosages contributed to environmental and economic sustainability as they require lower quantities of raw materials and diesel for materials transportation. The total costs of alkali-activated binder dosages ($189.79 and $154.45) were higher than that of Portland cement ($72.49 and $54.04), mainly due to the high cost of NaOH acquisition. However, the alkali-activated binder dosages implied lower carbon dioxide (CO2) emissions and thus lower social cost of CO2. The alternative binder presented a higher positive social impact. The alkali-activated high-density/low binder dosage is the most sustainable soil stabilization strategy.
Assuntos
Celulose , Saccharum , Solo , Animais , Solo/química , Mudança Social , Dióxido de Carbono , Casca de Ovo , Hidróxido de Sódio , ÁlcalisRESUMO
Renewable materials of biological origin exhibit attractive properties in relation to traditional plastics, as they can be partially or completely replaced, thereby reducing environmental impacts. Hemicelluloses are a group of polysaccharides that have expanded applications when acetylated. Acetylation can improve the mechanical strength and water vapor barrier properties of xylan-based bioplastics. By partially acetylating xylan in the present study, it was possible to use water as a solvent for the film-forming solution and starch as a second polysaccharide in the formation of bioplastics. Xylan was modified via partial chemical acetylation by varying the reaction time, solvent, and catalyst content. The bioplastics were formed by non-acetylated xylan and acetylated xylan with degrees of substitution (DS) of 0.45 and 0.9, respectively, with starch to form blends using glycerol as a plasticizer. Acetylation with DS 0.45 showed better results in increasing the hydrophilicity of the bioplastic. On the other hand, acetylation influenced the thermal stability of bioplastics, increasing the maximum temperature of the degradation rate from 302 °C to 329 °C and 315 °C, owing to changes in the crystallinity of the polymers. In addition to the modulus of elasticity 2.99 to 290.61 and 274.67 MPa for the non-acetylated bioplastic and the bioplastic with DS of 0.45 and 0.90, respectively. Thus, the films obtained presented suitable physicochemical properties for use in various industrial applications, such as active and intelligent packaging in the food sector.
Assuntos
Amido , Xilanos , Amido/química , Xilanos/química , Vapor , Plásticos , SolventesRESUMO
Sugarcane bagasse was pretreated with dilute phosphoric acid or sulfuric acid to facilitate cellulose hydrolysis and lignin extraction. With phosphoric acid, only 8 % of the initial cellulose was lost after delignification, whereas pretreatment with sulfuric acid resulted in the solubilization of 38 % of the initial cellulose. After enzymatic hydrolysis, the process using phosphoric acid produced approximately 35 % more glucose than that using sulfuric acid. In general, the lignins showed 95-97 % purity (total lignin, w/w), an average molar mass of 9500-10,200 g mol-1, a glass transition temperature of 140-160 °C, and a calorific value of 25 MJ kg-1. Phosphoric acid lignin (PAL) was slightly more polar than sulfuric acid lignin (SAL). PAL had 13 % more oxidized units and 20 % more OH groups than SAL. Regardless of the acid used, the lignins shared similar properties, but differed slightly in the characteristics of their functional groups and chemical bonds. These findings show that pretreatment catalyzed with either of the two acids resulted in lignin with sufficiently good characteristics for use in industrial processes.
Assuntos
Celulose , Saccharum , Celulose/química , Lignina/química , Saccharum/química , Hidrólise , Ácidos Fosfóricos , Ácidos SulfúricosRESUMO
This work studied the optimization of enzymatic saccharification of Agave tequilana bagasse (ATB) pretreated with the low-cost protic ionic liquid (PIL) ethanolamine acetate ([EOA][OAc]) using the highly available and cost-effective mixture of the enzymatic cocktails Celluclast 1.5L-Viscozyme L. Response surface methodology (RSM) was employed to maximize the sugars concentration and yield. The RSM optimization conditions of the enzymatic saccharification of pretreated ATB that achieved the maximum reducing sugars (RS) concentration were: 11.50 % w/v solids loading, 4.26 pH with 0.76 and 1.86 mg protein/mL buffer of Viscozyme L and Celluclast 1.5L, respectively. Similarly, the conditions that maximize the sugar yield (SY) were solids loading of 5.62 % w/v, and 4.51 pH as well as 1.07 and 2.03 mg protein/mL buffer of Viscozyme L and Celluclast 1.5L, respectively. Saccharification performance of the first-generation and low-cost enzyme mixture Celluclast 1.5L-Viscozyme L was compared with that reached by a second-generation and higher-cost CTec2, where Celluclast 1.5L-Viscozyme L achieved 60.86 ± 2.66 % y 79.25 ± 3.34 % of the sugars released by CTec2 at the same hydrolysis time (12 h) for the sugar concentration and yield models, respectively. These results are encouraging since they positively contribute to cost reduction and availability issues, which are key parameters to consider when thinking about scaling-up the process.
Assuntos
Agave , Celulose , Líquidos Iônicos , Análise Custo-Benefício , Carboidratos , Hidrólise , AçúcaresRESUMO
Cost is the crucial impediment in commercializing microalgal biodiesel. Therefore, cultivating microalgae in cost-effective nutrients reduces the upstream process cost remarkably. Thus, in this study, sugar cane bagasse hydrolysate (SBH) as a lucrative carbon supplement for Chlorococcum sp. and subsequent lipid extraction via an optimized solvent system for biodiesel production was investigated. Characterization of SBH revealed the presence of various monosaccharides and other sugar derivatives such as glucose, fructose, xylose, arabinose, etc. The maximum dry cell weight of 1.7 g/L was estimated in cultures grown in 10 mL SBH. Different solvents such as diethyl ether (DEE), chloroform (CHL), ethyl acetate (ETA), hexane (HEX), methanol (MET), ethanol (ETOH), acetone (ACE) and also combination of solvents (2:1 ratio) such as DEE: MET, CHL: MET, HEX: MET, HEX: ETOH was tested for lipid extraction efficacy. Among solvents used, 12.3% and 18.4% of lipids were extracted using CHL and CHL: MET, respectively, from 10 mL SBH amended cultures. However, the biodiesel yield was found to be similar at about 70.16 % in both SBH and no SBH-added cultures. The fatty acid profile of the biodiesel shows palmitic, oleic, linoleic, linolenic, and arachidonic acid as principal fatty acids. Further, the levels of SFAs, MUFAs, and PUFAs in 10 mL SBH-added cells were 24.67, 12.89, and 34.24%, respectively. Eventually, the fuel properties of Chlorococcum sp. biodiesel, satisfying international biodiesel standards, make the biodiesel a viable diesel substitute in the future.
Assuntos
Microalgas , Saccharum , Ácidos Graxos , Solventes , Lipídeos , Biocombustíveis , Carbono , Metanol , BiomassaRESUMO
The phytopathogenic fungus Chrysoporthe cubensis is a relevant source of lignocellulolytic enzymes. This work aimed to compare the profile of lignocellulose-degrading proteins secreted by C. cubensis grown under semi-solid state fermentation using wheat bran (WB) and sugarcane bagasse (SB). The exoproteomes of the fungus grown in wheat bran (WBE) and sugarcane bagasse (SBE) were qualitative and quantitatively analyzed by liquid chromatography-electrospray ionization tandem mass spectrometry (LC-ESI-MS/MS). Data are available via ProteomeXchange with identifier PXD046075. Label-free proteomic analysis of WBE and SBE showed that the fungus produced a spectrum of carbohydrate-active enzymes (CAZymes) with exclusive characteristics from each extract. While SBE resulted in an enzymatic profile directed towards the depolymerization of cellulose, the enzymes in WBE were more adaptable to the degradation of biomass rich in hemicellulose and other non-lignocellulosic polymers. Saccharification of alkaline pre-treated sugarcane bagasse with SBE promoted glucose release higher than commercial cocktails (8.11 g L-1), while WBE promoted the higher release of xylose (5.71 g L-1). Our results allowed an in-depth knowledge of the complex set of enzymes secreted by C. cubensis responsible for its high lignocellulolytic activity and still provided the identification of promising target proteins for biotechnological applications in the context of biorefinery.
Assuntos
Celulose , Saccharum , Celulose/metabolismo , Proteômica , Saccharum/metabolismo , Espectrometria de Massas em Tandem , Proteínas Fúngicas/metabolismo , Fibras na Dieta/metabolismo , HidróliseRESUMO
Β-Carotene is a red-orange pigment that serves as a precursor to important pharmaceutical molecules like vitamin A and retinol, making it highly significant in the industrial sector. Consequently, there is an ongoing quest for more sustainable production methods. In this study, glucose and xylose, two primary sugars derived from sugarcane bagasse (SCB), were utilized as substrates for ß-carotene production by Rhodotorula glutinis CCT-2186. To achieve this, SCB underwent pretreatment using NaOH, involved different concentrations of total solids (TS) (10%, 15%, and 20%) to remove lignin. Each sample was enzymatically hydrolyzed using two substrate loadings (5% and 10%). The pretreated SCB with 10%, 15%, and 20% TS exhibited glucose hydrolysis yields (%wt) of 93.10%, 91.88%, and 90.77%, respectively. The resulting hydrolysate was employed for ß-carotene production under batch fermentation. After 72 h of fermentation, the SCB hydrolysate yielded a ß-carotene concentration of 118.56 ± 3.01 mg/L. These findings showcase the robustness of R. glutinis as a biocatalyst for converting SCB into ß-carotene.
RESUMO
This article presents an experimental study to analyze the mechanical properties of a soil stabilized with ordinary Portland cement (OPC) under a sustainable approach consisting of a significant substitution of OPC for sugarcane bagasse ash (SCBA) to reduce the quantity of cement used in the stabilization, reaching the necessary mechanical requirements for its use as a subgrade layer. Soil specimens were elaborated with 3%, 5%, and 7% OPC as a stabilizing agent by weight of the soil. These mixtures were then partially substituted with 25%, 50%, and 75% SCBA, with these percentages being by weight of the stabilizer (OPC). Compaction, compressive strength, and California bearing ratio (CBR) tests were performed to evaluate the mechanical properties of the specimens. The results indicate that a 25% substitution of OPC by SCBA shows a similar performance to the mixture with only Portland cement, so a reduction in OPC use can be made. Further, with a substitution of 100% OPC by SCBA, the CBR of natural soil without stabilizers is improved.
RESUMO
Graphene-based materials have increasingly attracted attention in recent years. It is a material is recognized worldwide due to its numerous applications in several sectors. However, graphene production involves several challenges: scalability, high costs, and high-quality production. This study synthesized graphene-like porous carbon nanosheets (GPCNs) through a thermochemical process under a nitrogen atmosphere using grape bagasse as a precursor. Three temperatures (700, 800, and 900 ºC) of the pyrolysis process were studied. Chemical graphitization and activation were used to form high-specific surface area materials: FeCl3.6H2O(aq) and ZnCl2(s) in a simultaneous activation-graphitization (SAG) method. The materials obtained (GPCN700, GPCN800, and GPCN900) were compared to previously produced chars (C700, C800, and C900). A high specific surface area and total pore volume were obtained for GPCN materials, and GPCN900 presented the highest values: 1062.7 m2g-1 and 0.635 cm3 g-1, respectively. The GPCN and char materials were classified as mesoporous and applied as adsorbents for CO2(g). The GPCN800 presented the best CO2(g) adsorbent, with a CO2(g) adsorption capacity of 168.71 mg g-1.
Assuntos
Grafite , Vitis , Carbono , Dióxido de Carbono , PorosidadeRESUMO
Endophytic fungi constitute a major part of the still unexplored fungal diversity and have gained interest as new biological sources of natural active compounds, including enzymes. Endophytic fungi were isolated from soybean leaves and initially screened on agar plates for the production of CMCase (carboxymethylcellulase), xylanase, amylase and protease. The highest Enzymatic Indexes (IE) were verified for xylanase (2.14 and 1.31) with the fungi M6-A6P5F2 and M12-A5P3F1.2 and CMCase (1.92 and 1.62) with the fungi M13-A9P2F1 and M12-A5P3F1.2, respectively. The production of xylanase and CMCase by the selected fungi was evaluated in submerged cultivation using beechwood xylan and carboxymethylcellulose (CMC), as well as sugarcane straw and bagasse in different ratios as carbon sources. Both types of lignocellulosic biomass proved to be good inducers of enzymatic activity. The best xylanase producer among the isolates was identified as Colletotrichum boninense. With this fungus, the highest xylanase activity was obtained with a sugarcane straw-bagasse mixture in a 50:50 ratio (383.63 U mL-1), a result superior to that obtained with the use of beechwood xylan (296.65 U mL-1). Regardingthe kinetic behavior of the crude xylanase, there was found optimal pH of 5.0 and optimal temperatures of 50°C and 60°C. At 40°C and 50°C, xylanase retained 87% and 76% of its initial catalytic activity, respectively. These results bring new perspectives on bioprospecting endophytic fungi for the production of enzymes, mainly xylanase, as well as the exploitation of agro-industrial by-products, such as sugarcane straw and bagasse.
Assuntos
Saccharum , Xilanos , Saccharum/microbiologia , Biomassa , FungosRESUMO
To reduce the environmental impacts from sodium silicate synthesis, a ceramic method was suggested, with sugarcane bagasse ash (SCBA) as the source of silicon dioxide and sodium carbonate. Although the production of sodium silicate is carried out on a large scale, it should be noted that its process requires temperatures above 1000 °C; it also requires the use of highly corrosive agents such as sodium hydroxide and chlorine gas to neutralize the remaining sodium hydroxide. In the present study, the synthesis temperatures were reduced to 800 °C with a reaction time of 3 h by pressing equimolar mixtures of previously purified SCBA and sodium carbonate; then, heat treatment was carried out under the indicated conditions. The resulting materials were analyzed with Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). Among the crystalline phases, calcium disodium silicate was identified, in addition to sodium silicate; thus, it was inferred that the other components of the ash can interfere with the synthesis of silicate. Therefore, in order to obtain the highest composition of sodium silicate, a leaching treatment of the SCBA is required.