RESUMO
In Mexico, corn and the nixtamalization technique hold immense culinary and economic significance. Thus, optimizing and offering alternatives for this process is critical. This research proposes a solar-driven nixtamalization method customized for native maize varieties in Michoacán, Mexico. The objective is to present a technique that is energy-efficient, environmentally friendly, socially acceptable, and cost-effective. We devised a straightforward yet effective nixtamalization process utilizing the HSMC solar furnace. This method encompasses:â¢Field research to understand the practices and traditions regarding nixtamalization and the most consumed maize varieties.â¢Thermal determination and profiling of the solar oven to be used for each case study.For the rural areas of Michoacán, solar nixtamalization presents a practical and eco-sustainable alternative in both energy usage and economic terms. However, those interested in its local application must consider that the duration may vary due to differing climatic conditions and maize types.
RESUMO
Holographic lenses (HLs) are part of holographic optical elements (HOE), and are being applied to concentrate solar energy on a focal point or focal line. In this way, the concentrated energy can be converted into electrical or thermal energy by means of a photovoltaic cell or a thermal absorber tube. HLs are able to passively track the apparent motion of the sun with a high acceptance angle, allowing tracking motors to be replaced, thus reducing the cost of support structures. This article focuses on a review of the materials used in the recording of a holographic lens (HL) or multiple HLs in photovoltaic and/or concentrating solar collectors. This review shows that the use of photopolymers for the recording of HLs enables high-performance efficiency in physical systems designed for energy transformation, and presents some important elements to be taken into account for future designs, especially those related to the characteristics of the HL recording materials. Finally, the article outlines future recommendations, emphasizing potential research opportunities and challenges for researchers entering the field of HL-based concentrating solar photovoltaic and/or concentrating solar thermal collectors.
RESUMO
Given the current and escalating global energy and environmental concerns, this work explores an innovative approach to mitigate a widely employed commercial herbicide using a direct glyphosate (Gly) photocatalytic fuel cell (PFC). The device generates power continuously by converting solar radiation, degrading and mineralizing commercial glyphosate-based fuel, and reducing sodium persulfate at the cathode. Pristine and modified hematite photoanodes were coupled to Pt/C nanoparticles dispersed in a carbon paper (CP) support (Pt/C/CP) dark cathode by using an H-type cell. The Gly/persulfate PFC shows a remarkable current and power generation enhancement after dual-surface modification of pristine hematite with segregated Hf and FeNiOx cocatalysts. The optimized photoanode elevates maximum current density (Jmax) from 0.35 to 0.71 mA cm-2 and maximum power generation (Pmax) from 0.04 to 0.065 mW cm-2, representing 102.85 and 62.50% increase in Jmax and Pmax, respectively, as compared to pristine hematite. The system demonstrated stability over a studied period of 4 h; remarkably, the photodegradation of Gly proved substantial, achieving â¼98% degradation and â¼6% mineralization. Our findings may significantly contribute to reducing Gly's environmental impact in agribusiness since it may convert the pollutant into energy at zero bias. The proposed device offers a sustainable solution to counteract Gly pollution while concurrently harnessing solar energy for power generation.
RESUMO
A mixed-mode solar drying was developed to evaluate the physicochemical and colorimetric properties of Zompantle (Erythrina americana). A 22-factorial design was used; the operation mode (mesh shade and direct) and airflow (natural convection and forced convection) were established as factors in this design. The initial moisture content in the Zompantle flower was reduced from 89.03% (w.b) to values that ranged from 3.84% to 5.84%; depending on the operation mode of the dryer, the final water activity ranged from 0.25 to 0.33. The Zompantle's components as proteins (4.28%), antioxidant activity (18.8%), carbohydrates (4.83%), fat (0.92%), fiber (3.71%), ash (0.94%), and total soluble solids (3°Brix) increased as the water was evaporated during the drying. The increment in the Zompantle's components depends on the operation mode; in direct mode and natural convection, the proteins, antioxidant activity, carbohydrates, fat, fiber, ash, and total soluble solids were 6.99%, 61.69%, 79.05%, 1.20%, 3.84%, 8.70%, and 45 °Brix, respectively. The total drying efficiency was 14.84% with the direct mode and natural convection (DM-NC) and 17.10% with the mesh shade and natural convection (MS-NC). The Hue angle measures the property of the color; the indirect mode and natural convection keep the hue angle close to the initial value (29.2 °). The initial chroma value of the Zompantle flower was 55.07; the indirect mode and natural convection kept high saturation (37.58); these dry conditions ensured a red color in the dehydrated Zompantle. Dehydrated Zompantle's flowers could have several practical applications, such as an additive in traditional Mexican cuisine.
Assuntos
Antioxidantes , Erythrina , Antioxidantes/química , Colorimetria , Carboidratos , ÁguaRESUMO
Excess energy derived from photosynthesis can be used in plant microbial fuel cell (PMFC) systems as a sustainable alternative for the generation of electricity. In this study, the in situ performance of CAM (Crassulacean acid metabolism) plants in Calama, in the Atacama Desert, was evaluated for energy recovery using PMFCs with stainless steel AISI 316L and Cu as electrodes. The plant species evaluated included Aloe perfoliata, Cereus jamacaru, Austrocylindropuntia subulata, Agave potatorum, Aloe arborescens, Malephora crocea, and Kalanchoe daigremontiana. Among the plant species, Kalanchoe daigremontiana demonstrated significant potential as an in situ PMFC, showing a maximum cell potential of 0.248 V and a minimum of 0.139 V. In addition, the cumulative energy for recovery was about 9.4 mWh m-2 of the electrode. The use of CAM plants in PMFCs presents a novel approach for green energy generation, as these plants possess an inherent ability to adapt to arid environments and water-scarce areas such as the Atacama Desert climate.
RESUMO
High-performance nanosized optoelectronic devices based on van der Waals (vdW) heterostructures have significant potential for use in a variety of applications. However, the investigation of nanoribbon-based vdW heterostructures are still mostly unexplored. In this study, based on first-principles calculations, we demonstrate that a Sb2S3/Sb2Se3 vdW heterostructure, which is formed by isostructural nanoribbons of stibnite (Sb2S3) and antimonselite (Sb2Se3), possesses a direct band gap with a typical type-II band alignment, which is suitable for optoelectronics and solar energy conversion. Optical absorption spectra show broad profiles in the visible and UV ranges for all of the studied configurations, indicating their suitability for photodevices. Additionally, in 1D nanoribbons, we see sharp peaks corresponding to strongly bound excitons in a fashion similar to that of other quasi-1D systems. The Sb2S3/Sb2Se3 heterostructure is predicted to exhibit a remarkable power conversion efficiency (PCE) of 28.2%, positioning it competitively alongside other extensively studied two-dimensional (2D) heterostructures.
RESUMO
It is urgent yet challenging to develop new environmentally friendly and cost-effective sources of energy. Molecular solar thermal (MOST) systems for energy capture and storage are a promising option. With this in mind, we have prepared a new water-soluble (pH > 6) norbornadiene derivative (HNBD1) whose MOST properties are reported here. HNBD1 shows a better matching to the solar spectrum compared to unmodified norbornadiene, with an onset absorbance of λonset = 364 nm. The corresponding quadricyclane photoisomer (HQC1) is quantitatively generated through the light irradiation of HNBD1. In an alkaline aqueous solution, the MOST system consists of the NBD1-/QC1- pair of deprotonated species. QC1- is very stable toward thermal back-conversion to NBD1-; it is absolutely stable at 298 K for three months and shows a marked resistance to temperature increase (half-life t½ = 587 h at 371 K). Yet, it rapidly (t½ = 11 min) releases the stored energy in the presence of the Co(II) porphyrin catalyst Co-TPPC (ΔHstorage = 65(2) kJâmol-1). Under the explored conditions, Co-TPPC maintains its catalytic activity for at least 200 turnovers. These results are very promising for the creation of MOST systems that work in water, a very interesting solvent for environmental sustainability, and offer a strong incentive to continue research towards this goal.
RESUMO
The solar electroflotation (EF) processes using saline electrolytes are today one of the great challenges for the development of electrochemical devices, due to the corrosion problems that are generated during the operation by being in permanent contact with Cl- ions. This manuscript discloses the corrosion behavior of titanium electrodes using a superposition model based on mixed potential theory and the evaluation of the superficial performance of the Ti electrodes operated to 4 V/SHE solar electroflotation in contact with a solution of 0.5 M NaCl. Additionally provided is an electrochemical analysis of Ti electrodes regarding HER, ORR, OER, and CER that occur during the solar saline EF process. The non-linear superposition model by mixed potential theory gives electrochemical and corrosion parameters that complement the information published in scientific journals, the corrosion current density and corrosion potential in these conditions is 0.069 A/m2 and -7.27 mV, respectively. The formation of TiO2 and TiOCl on the anode electrode was visualized, resulting in a reduction of its weight loss of the anode electrode.
RESUMO
The use of models capable of forecasting the production of photovoltaic (PV) energy is essential to guarantee the best possible integration of this energy source into traditional distribution grids. Long Short-Term Memory networks (LSTMs) are commonly used for this purpose, but their use may not be the better option due to their great computational complexity and slower inference and training time. Thus, in this work, we seek to evaluate the use of neural networks MLPs (Multilayer Perceptron), Recurrent Neural Networks (RNNs), and LSTMs, for the forecast of 5 min of photovoltaic energy production. Each iteration of the predictions uses the last 120 min of data collected from the PV system (power, irradiation, and PV cell temperature), measured from 2019 to mid-2022 in Maceió (Brazil). In addition, Bayesian hyperparameters optimization was used to obtain the best of each model and compare them on an equal footing. Results showed that the MLP performs satisfactorily, requiring much less time to train and forecast, indicating that they can be a better option when dealing with a very short-term forecast in specific contexts, for example, in systems with little computational resources.
RESUMO
Resumen La industria alimentaria utiliza hasta el 15 % del total de la energía eléctrica que demanda el sector industrial, principalmente en procesos de secado. Esto suscita la búsqueda de nuevas alternativas de secado que reduzcan el uso de energía eléctrica. Una opción es el secado solar, principalmente, el de tipo indirecto, a través de captadores solares de placa plana (CSPP). El objetivo de este trabajo fue analizar los recientes desarrollos de los CSPP, características, ventajas, desventajas, eficiencia y diversas tecnologías utilizadas en conjunto, para aumentar la eficiencia térmica en el secado solar. Los CSPP han desarrollado, a través de la hibridación con la utilización de otras fuentes de energía (eléctrica, biomasa, solar), un incremento en su eficiencia que los vuelve cada vez más viables para ser utilizados en procesos comerciales de secado de alimentos.
Abstract The food industry uses up to 15 % of the total electrical energy demanded by the industrial sector, mainly in drying processes. This motivates the search for new drying alternatives that reduce the use of electrical energy. One option is solar drying; mainly indirect type solar drying, that uses flat plate solar collectors (FPSC). The objective of this work was to analyze the recent developments of the FPSC, their characteristics, advantages, disadvantages, efficiency, and the range of technologies used in conjunction with the FPSC to increase their thermal efficiency for solar drying. The FPSC have developed through hybridization with the use of other energy sources (electricity, biomass, solar), an increase in their efficiency, that increasingly turns them into viable options for food drying processes.
RESUMO
In this paper, we present the first study of the long-term climate-change impact on photovoltaic power potential in Nariño, Colombia. In this region, more than half of the territory does not have a constant electricity supply, but it has great potential for solutions with renewable energy sources. Based on the Coordinated Regional Downscaling Experiment (CORDEX), we assess the change in photovoltaic power potential towards the end of this century, considering two climate change scenarios, one optimistic and the other pessimistic. Our results suggest that changes in photovoltaic power potential, by the end of the century, will have a maximum decrease of around 2.49% in the central zone of Nariño, with some non-affected areas, and a maximum increase of 2.52% on the southeastern side with respect to the pessimistic climate change scenario.
RESUMO
Global Horizontal Irradiance was measured using a thermopile-type pyranometer during more than three years using a sample time of two seconds, with the purpose of capturing fast transient events of irradiance which are notable in tropical regions as the one where these data were collected: Bogotá, Colombia. The date and time of each measurement were registered along with the irradiance values. In addition, other related quantities were calculated and included for each one of the measurement instants: Optical Air Mass, Zenith angle, Extraterrestrial Solar Irradiance, and Clearness Index. Daily aggregated statistics of irradiance were calculated and are provided here too. Data points corresponding to nights were discarded. The raw data was analyzed to remove incomplete days, to guarantee that daily statistics are accurate and meaningful. After this data cleaning process, 1016 complete days remain, having a total of 21,959,912 data points. These data are useful for studying the effect of irradiance transients over photovoltaic systems, including power electronics, batteries and electric loads; it can also be used in studies about the stability of the radiative regime or the variability of irradiance such as Avila et al. (2019) (where part of these data was effectively used) and other related works cited there.
RESUMO
This article explores the patents of solar energy technologies in the organic Rankine cycle (ORC) applications. The conversion of low-quality thermal energy into electricity is one of the main characteristics of an ORC, making efficient and viable technologies available today. However, only a few and outdated articles that analyze patents that use solar energy technologies in ORC applications exist. This leads to a lack of updated information regarding the number of published patents, International Patent Classification (IPC) codes associated with them, technology life cycle status, and the most relevant patented developments. Thus, this article conducts a current investigation of patents published between January 2010 and May 2022 using the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology and keywords. One thousand two hundred ninety-nine patents were obtained as part of the study and classified in F and Y groups of the IPC. The time-lapse analyzed was between January 2010 and May 2022. In 2014 and 2015, a peak of published patents was observed. China (CN) was the country that published the most significant number of patents worldwide. However, the European Patent Office (EP), the World Intellectual Property Organization (WO), and the United States (US) publish the patents with the highest number of patent citations. Furthermore, the possible trend regarding the development of patents for each technology is presented. A high-performance theoretical ORC plant based on the patent information analyzed by this article is introduced. Finally, exploration of IPC revealed 17 codes related to solar energy technologies in ORC applications not indexed in the main search.
RESUMO
Electricity consumption in Brazil increases significantly, making feasibility studies to diversify the Brazilian electricity mix with other renewable sources become essential. However, the electricity market continues to be primarily driven by government or regulatory incentives and economic status. With the coronavirus pandemic since the beginning of 2020, the market has been undergoing significant changes that cause uncertainty in consumer investments in grid-connected photovoltaic systems. This article presents an economic feasibility analysis of photovoltaic system installation for the Brazilian residential sector, estimating a cash and term investment and comparing the viability of the investment before the global pandemic (December 2019) with the pandemic scenario (April 2021) for each of the 27 Brazilian capitals. The baseline scenario for economic feasibility analysis calculations considered a power system of 4 kW. The results show that the effects of the pandemic in the electricity market were positive in the feasibility of investing in grid-connected photovoltaic systems. Also, financing the system increases the chances of profitability. The current scenario is possibly the most attractive ever experienced by potential investors. However, this favorable scenario could decline in the coming years due to climatic and governmental factors.
RESUMO
Tourism activity in Peru has been experiencing significant growth in the last ten years, positioning this economic sector as the third largest contributor to the National Gross Domestic Product (GDP). Likewise, Peru has a high ecological and climate diversity, which makes it the possessor of renewable energy potential, specifically solar and wind power. The rapid growth of tourism is leading to generating prospects for becoming a sustainable destination. In this sense, it is important to understand and evaluate the Peruvian legislative framework for sustainable tourism and the current state of the implementation of the scenarios provided by the governmental entity in terms of sustainability, and its link with tourism activity. Based on what has been described, this study is aimed at evaluating the four most relevant museums in the northern part of Peru; in addition, it contributes to the studies that exist at the intersection of tourism and sustainability in the chains of activities related to tourism and calls for rationality applied to tourism management in this region of Latin America. The results of the literature review of the Peruvian legal framework reveal a lack of specific laws and regulations on sustainable tourism; on the contrary, there are policies in force that contribute to promoting the development of sustainable tourism. The quantified evaluation of the solar and wind potentials of the geographical area under study indicates the minimum renewable energy potential necessary for its transformation and use in the development of sustainable museums and its contribution to sustainable tourism.
RESUMO
In this work, the production of biologically synthesized silica nanoparticles was proposed to prepare a nanosuspension as a thermal fluid in parabolic solar panels at the laboratory level. Silica nanoparticles were produced from construction sand in two stages. Biosynthesis broth was produced by Aspergillus niger aerated fermentation in a 1 L bioreactor for 9 days. Each supernatant was contacted with 18% construction sand in a 500 L reactor with mechanical agitation, at a temperature of 25 °C, and a contact time of 30 min. Subsequently, the separation process was carried out. For day 9, a pH value of 1.71 was obtained as well as acid concentrations of 15.78 g/L for citrus and 4.16 g/L for malic. The metal extraction efficiency of Si nanoparticles was 19%. The vibration peaks in the FTIR were characteristic of the presence of silica nanoparticles in wavenumbers 1020 cm-1 and 1150 cm-1. Finally, a prototype solar radiation test bench for parabolic systems was built and provided with a radiation source that falls on a translucent pipe that transports the nanoparticles, which has a pump and a series of thermocouples. The heat capacity of the biotechnologically produced silica nanoparticle suspension was 0.72 ± 0.05 kJ/kgK, using material and energy balances in the flow circuit.
RESUMO
OBJECTIVE: This cross-sectional study aimed to evaluate the prevalence and factors potentially associated with the development of actinic cheilitis (AC) in Brazilian rural workers. SUBJECTS AND METHODS: A professional performed all physical examinations and evaluations using semi-structured questionnaires in 240 rural workers. RESULTS: Eighty-three participants were diagnosed with AC (34.6%). It was more prevalent among workers older than 45 years (3.29-10.96 95% IC; OR = 3.30; p = .0018), Caucasians (phototypes I and II) (4.78-16.12 95% IC; OR = 10.81; p < .0001), illiterate individuals (2.16-21.59 95% IC; OR = 10.43; p = .0037), those with 6 or fewer years of formal schooling (2.03-7.89 95% IC; OR = 4.63; p = .0013), those regularly using pesticides (1.58-6.64 95% IC; OR = 2.79; p = .0260) and those who used the private health service in their last appointment (1.17-3.54 95% IC; OR = 2.72; p = .0083). CONCLUSION: There was a substantial prevalence of AC among rural workers with advanced age, white skin, and illiteracy, those with lower levels of education, those who regularly use pesticides, and those who utilised private health services in their last appointment. Thus, healthcare strategies that include rural workers are required for the control and prevention of AC in both public and private health services.
Assuntos
Queilite , Brasil/epidemiologia , Queilite/epidemiologia , Estudos Transversais , Humanos , PrevalênciaRESUMO
All inorganic layer-by-layer (LbL) thin films composed by TiO2nanoparticles and [Al(OH)4]-anions (TiO2/AlOx) as well as Al2O3and Nb2O5nanoparticles (Al2O3/Nb2O5) have been deposited to fluorine-doped tin-oxide coated glass (FTO) surfaces and applied as blocking layers in dye-sensitized solar cells (DSCs). Structural and morphological characterization of the LbL films by different techniques reveal that inTiO2/AlOxassembly, aluminate anions undergo condensation reactions on the TiO2surface leading to the formation of highly homogeneous films with unique optical properties. After 25 depositions transmittance losses below 10% in relation to the bare FTO substrate are observed. Electrochemical impedance spectroscopy shows thatTiO2/AlOxlayers impose an effective barrier for the charge recombination at FTO/electrolyte interface with an electron exchange time constant 50-fold higher than that for bare FTO. As a result, an improvement of 85% in the overall conversion efficiency of DSCs was observed with the employment of TiO2/AlOxblocking layers.Al2O3/Nb2O5LbL films can also work as blocking layers in DSCs but not as efficient, which is associated with the poor homogeneity of the film and its capacitive behavior. The production of cost-effective blocking layers with a low light scattering in the visible region is an important feature toward the application of DSC in other Building-integrated photovoltaic applications.
RESUMO
Using the Scopus database between the years of 2000 and 2019, a bibliometric study was done to analyze the scientific publications in the area of photovoltaic solar energy management. From the preliminary analysis of future research tendencies, ten possibilities of study topics were developed; and due to that it was possible to assume that even though many studies of technological development are found, some insights can still be approached in a way that the practical implementation of solar systems photovoltaic is better used. This data was validated by the analysis performed with the Scimat scientific mapping software under a longitudinal structure, verifying the future tendencies researches mentioned previously.
RESUMO
This dataset is part of the article entitled "Design and experimental study of a low-cost prefab Trombe Wall to improve indoor temperatures in social housing in the Biobío Region in Chile" [1], [2]. The dataset represents the outcome of experimental measurements during a 1-year monitoring campaign to assess the performance of an adaptable and low-cost prefabricated Trombe Wall (TW) with a vertical water storage system. The experiments include periods with mobile insulation during winter nights and external shading during summer which were added to test their effect on the thermal performance. Temperature sensors were used to measure and compare the temperature in two test cells: one with and one without the TW. Following the National Chilean Standard [3], the experiment was done in the interior valley (Chillan), a Mediterranean climate (Csb), according to the Köppen climate classification [4]. The two test cells were designed to represent the most used area of a social housing unit in combination with the most widely used type of window in north façades in the region. One test cell was built exactly as the social housing unit, while the second test cell included a low-cost Trombe wall. Five temperature sensors were installed in the test cells. The thermal performance of the TW was monitored and analysed for the first time in Chile, providing insights in the thermal performance of the TW and proving the potential effectiveness of seasonal variations to improve winter and summer performances.