RESUMO
Inverted perovskite solar cells (PSCs) have gained much attention due to their low hysteresis effect, easy fabrication, and good stability. In this research, an inverted perovskite solar cell ITO/PEDOT:PSS/CH3NH3PbI3/PCBM/Ag structure was simulated and optimized using SCAPS-1D version 3.3.10 software. The influence on the device of parameters, including perovskite thickness, total defect density, series and shunt resistances, and operating temperature, are discussed and analyzed. With optimized parameters, the efficiency increased from 13.47% to 18.33%. Then, a new SiOx/ITO/PEDOT:PSS/CH3NH3PbI3/PCBM/Ag device was proposed which includes a silicon-rich oxide (SiOx) layer. This material was used as the down-conversion energy material, which converts high-energy photons (ultraviolet UV light) into low-energy photons (visible light), improving the stability and absorption of the device. Finally, with SiOx, we obtained an efficiency of 22.46% in the simulation. Therefore, the device with the SiOx layer is the most suitable as it has better values for current density-voltage output and quantum efficiency than the device without SiOx.
RESUMO
Simulation and analysis of solar cells based on the heterojunction of zinc oxide doped with aluminum (AZO) and cadmium telluride (CdTe) with the structure (Al/AZO/CdTe/NiO/Ni) using the Simulator of the capacitance of solar cells - 1 dimension (SCAPS-1D) has been presented in this paper. AZO is used as a window layer and Nickel oxide (NiO) has been introduced as a hole transport layer (HTL). Through the software, the effect of thickness, absorber (CdTe), and window (AZO) layers carrier concentration, operating temperature, and resistances (series and shunt) have been studied. Simulation results show that the solar cell performance can be greatly improved by adjusting the layer's thickness and carrier concentration, obtaining optimal values of 10 nm and 10 18 c m - 3 for the AZO layer, while for the CdTe layer they were 2 µm and 10 15 c m - 3 . The optimum series and shunt resistances are in the range of 1-3 Ω c m 2 and 1800-2200 Ω c m 2 respectively. A maximum power conversion efficiency (PCE) of 14.2% is achieved with an open circuit voltage (Voc) of 0.74 V, short circuit current density (Jsc) of 26.15 m A / c m 2 and a fill factor (FF) of 72.83%, this shows AZO potential to be considered as an interesting material to replace CdS window layer.
RESUMO
In this paper, a n-i-p planar heterojunction simulation of Sn-based iodide perovskite solar cell (PSC) is proposed. The solar cell structure consists of a Fluorine-doped tin oxide (FTO) substrate on which titanium oxide (TiO2) is placed; this material will act as an electron transporting layer (ETL); then, we have the tin perovskite CH3NH3SnI3 (MASnI3) which is the absorber layer and next a copper zinc and tin sulfide (CZTS) that will have the function of a hole transporting layer (HTL). This material is used due to its simple synthesis process and band tuning, in addition to presenting good electrical properties and stability; it is also a low-cost and non-toxic inorganic material. Finally, gold (Au) is placed as a back contact. The lead-free perovskite solar cell was simulated using a Solar Cell Capacitance Simulator (SCAPS-1D). The simulations were performed under AM 1.5G light illumination and focused on getting the best efficiency of the solar cell proposed. The thickness of MASnI3 and CZTS, band gap of CZTS, operating temperature in the range between 250 K and 350 K, acceptor concentration and defect density of absorber layer were the parameters optimized in the solar cell device. The simulation results indicate that absorber thicknesses of 500 nm and 300 nm for CZTS are appropriate for the solar cell. Further, when optimum values of the acceptor density (NA) and defect density (Nt), 1016 cm-3 and 1014 cm-3, respectively, were used, the best electrical values were obtained: Jsc of 31.66 mA/cm2, Voc of 0.96 V, FF of 67% and PCE of 20.28%. Due to the enhanced performance parameters, the structure of the device could be used in applications for a solar energy harvesting system.