RESUMO
In this work, graphene oxide (GO) was synthesized by the modified Hummers method. The nanomaterial was characterized by FTIR and Raman spectroscopy, SEM, and pH at the point of zero charge. GO exhibited typical characteristics of graphene-based materials, indicating that graphite oxidation and exfoliation occurred successfully. Cd (II) and Pb (II) adsorption onto GO was carried out in batch systems, in which the effect of adsorbent dosage, contact time, and initial adsorbate concentration were evaluated. Langmuir, Freundlich, and Sips isotherm models, as well as pseudo order models and Elovich kinetic equation were applied to adsorption experimental data. Results indicated that increasing adsorbent mass, the removal efficiency of Cd (II) and Pb (II) increased. Freundlich isotherm better described Pb (II) adsorption (R2 = 0.96), while Cd (II) isotherm showed linear behavior. From the Akaike's AIC parameter, kinetic data were satisfactorily described by pseudo-first order (Cd (II)) and pseudo-n order (Pb (II)) models. GO was successfully subjected to five regeneration cycles, maintaining high efficiency (> 90%) in all cycles. GO showed high potential for the adsorption of Cd (II) and Pb (II) from aqueous solution, due to its high adsorption capacity, rapid Cd (II) and Pb (II) intakes, and great regeneration performance.
Assuntos
Grafite , Poluentes Químicos da Água , Purificação da Água , Adsorção , Cádmio/análise , Grafite/química , Concentração de Íons de Hidrogênio , Cinética , Chumbo , Água , Poluentes Químicos da Água/análise , Purificação da Água/métodosRESUMO
The present situation of COVID-19 diverted our focus towards utilizing the degraded solar cells for sensor application, this will help in global energy harvesting. So, here is our successful effort to reuse already degraded solar cells as ultraviolet (UV) and infrared (IR) sensor. The spin-coated perovskite (CH3NH3PbI3-XClX) has been already tested for visible light spectrum, as an extension to that now it is utilized as UV and IR intensity sensors to cover the whole spectrum. The employed CH3NH3PbI3-XClX material was used after its efficiency loss has been reached to a saturation point in photovoltaic devices. Each deposited layer was investigated from UV to the IR absorption spectrum for deepening study through UV-vis spectroscopy. In the sandwiched architecture possessing FTO/PEDOT: PSS/Perovskite/PC61BM/CdS/Au symmetry, the perovskite film has been employed as an absorbent layer, however, other layers participation also plays a key role. The resultant device yielded very good sensing performance because of the enhanced excitons generation which is attributed to the precise selection of the interfacial materials, e.g. CdS and PC61BM as an ETM and PEDOT: PSS as HTM. The impedance and capacitance of the devices within 0.01-200â¯kHz under varied UV and IR illumination intensities were investigated. Measurements showed that as the intensity of the light increased i.e., UV (0-200â¯W/m2) and IR (0-5800â¯W/m2), impedance decreased while capacitance increased. The current results are attributed to the increase in the concentration of charges i.e., electron-hole pairs generation depending on the built-in capacitance and frequency of the charges.
RESUMO
The great quantity of synthetic plastic discarded inappropriately in the environment is forcing the search for materials that can be reprocessable and biodegradable. Blends between synthetic polymers and natural and biodegradable polymers can be good candidates of such novel materials because they can combine processability with biodegradation and the use of renewable raw materials. However, traditional polymers usually present high levels of recyclability and use the well-established recycling infrastructure that can eventually be affected by the introduction of systems containing natural polymers. Thus, this work aims to evaluate the effect of reprocessing (simulated here by multiple extrusions) on the structure and properties of a low density polyethylene/thermoplastic starch (LDPE/TPS) blend compared to LDPE. The results indicated that multiple extrusion steps led to a reduction in the average size of the starch-rich phases of LDPE/TPS blends and minor changes in the mechanical and rheological properties of the materials. Such results suggest that the LDPE/TPS blend presents similar reprocessability to the LDPE for the experimental conditions used.