RESUMO

Este relato de caso clínico tem como objetivo descrever a utilização de osso alógeno na reconstrução de maxila atrófica para posterior reabilitação com prótese fixa metalocerâmica sobre implantes, fazer uma análise histológica do tecido ósseo enxertado e descrever o acompanhamento clínico e radiográfico por 8 anos. Uma paciente de 54 anos, com edentulismo parcial e atrofia moderada-a-severa na maxila, apresentou-se para tratamento demonstrando muito interesse em receber prótese sobre implantes. Após exame clínico e radiográfico, foi realizada montagem dos modelos de estudo em ASA para enceramento diagnóstico e obtenção de um guia multifuncional (tomográfico/ cirúrgico). A tomografia indicou a necessidade de reconstrução óssea maxilar. Procedeuse então à aposição de blocos de osso alógeno para aumento horizontal nas regiões anterior e posterior da maxila. Um dos blocos foi triturado e utilizado para levantamento do assoalho do seio maxilar no lado esquerdo. Dez meses depois, uma nova tomografia foi solicitada, utilizando o mesmo guia inicial, e os implantes instalados, utilizando o guia multifuncional como guia cirúrgico. Neste momento, material ósseo foi coletado na interface osso enxertado/osso nativo com uma broca trefina. Os resultados histológicos demonstraram viabilidade das células ósseas no enxerto, além da presença de vasos sanguíneos. Após o tempo necessário para osseointegração, procedeu-se com tratamento protético. Nenhuma complicação foi relatada até oito anos de controle. A sequência de tratamento proposta forneceu bons resultados estéticos e funcionais. Concluiu-se, então, que o emprego de osso alógeno é uma alternativa viável para a reconstrução de rebordos alveolares severamente reabsorvidos(AU)

This clinical case report aims to describe the use of allogeneic bone in the atrophic maxilla reconstruction for subsequent rehabilitation with a fixed metal-ceramic prosthesis on implants; to perform a histological analysis of the grafted bone tissue; and to describe the clinical and radiographic monitoring for 8 years. A 54-year-old patient, with partial edentulism and moderate-to-severe atrophy in the maxilla showed great interest in receiving implant prostheses. After c linical and radiographic examination, the ASA study models were assembled for diagnostic waxing and a multifunctional guide (tomographic / surgical) was obtained. Tomography indicated the need for maxillary bone reconstruction. Allogeneic bone blocks were then placed for horizontal enlargement in the anterior and posterior regions of the maxilla. One of the blocks was crushed and used to lift the floor of the maxillary sinus on the left side. Ten months later, a new tomography was requested, using the same initial guide, and the implants installed, using the multifunctional guide as a surgical guide. At this time, bone material was collected at the grafted bone / native bone interface with a trephine drill. Histological results demonstrated viability of bone cells in the graft, besides the presence of blood vessels. After the necessary time for osseointegration, a prosthetic treatment was performed. No complications were reported up to eight years of control. The propose treatment sequence provided good aesthetic and functional results. It was concluded, then, that the use of allogeneic bone is a viable alternative for the reconstruction of severely reabsorbed alveolar edges(AU)

Assuntos

RESUMO

Abstract The aim of this study was to clinically and radiographically compare extra short and standards implants. Forty-two implants were installed in 10 selected patients. They received prosthetic loading only after the conventional waiting time for osseointegration and the prostheses were made ferulized. Radiographic shots were performed to evaluate vertical and horizontal bone losses at times T1 (prosthetic installation), T2 (6 months follow-up) and T3 (12 months follow-up). Biological parameters such as bone level around the implants (CBL) were evaluated, CBL alteration (CBLC), total crown length (TCL) and implant/crown ratio (ICR) were digitally calculated. All implants included in the study were submitted to the analysis of the implant stability quotient (ISQ) at the time of implant installation (T0) and at 12 months of prosthetic function (T3). Data were statistically tested. The ICR was higher in the test group than in the control group (p<0.0001). The CBL measurements at the beginning of the study were 0.21±0.19 mm and 0.32±0.38 mm and at 12 months 0.65±0.24 mm and 0.87±0.34 mm, respectively in the test and control groups. CBLCs and CBL were similar at all times (p>0.05). No correlation was found between CBLC and ICR parameters, as well as between ISQ and implant length. We may conclude that standards and extra short implants can provide similar clinical results in prosthetic rehabilitation of the atrophic jaw over 12 months of follow-up.

Resumo O objetivo deste estudo foi comparar clínica e radiograficamente implantes extra curtos e padrões. Quarenta e dois implantes foram instalados em 10 pacientes selecionados. Eles receberam carga protética somente após o tempo de espera convencional para a osseointegração e as próteses foram feitas ferulizadas. As imagens radiográficas foram realizadas para avaliar as perdas ósseas verticais e horizontais nos tempos T1 (instalação protética), T2 (6 meses de acompanhamento) e T3 (12 meses de acompanhamento). Parâmetros biológicos como nível ósseo ao redor dos implantes (CBL) foram avaliados, alteração CBL (CBLC), comprimento total da coroa (TCL) e relação implante / coroa (ICR) foram calculados digitalmente. Todos os implantes incluídos no estudo foram submetidos à análise do quociente de estabilidade do implante (ISQ) no momento da instalação do implante (T0) e aos 12 meses de função protética (T3). Os dados foram testados estatisticamente. A ICR foi maior no grupo teste do que no grupo controle (p<0,0001). As medidas de CBL no início do estudo foram de 0,21±0,19 mm e 0,32±0,38 mm e em 12 meses 0,65±0,24 mm e 0,87±0,34 mm, respectivamente nos grupos teste e controle. CBLCs e CBL foram semelhantes em todos os momentos (p>0,05). Não foi encontrada correlação entre os parâmetros CBLC e ICR, bem como entre o ISQ e o comprimento do implante. Podemos concluir que padrões e implantes extra curtos podem fornecer resultados clínicos semelhantes na reabilitação protética da mandíbula atrófica ao longo de 12 meses de acompanhamento.

Assuntos

RESUMO

Objetivos: melhorar a percepção do dentista sobre a atratividade do sorriso através de avaliações objetivas. Material e métodos: fotografias frontais de sorrisos (envolvendo a área dos caninos) foram aleatoriamente escolhidas e dispostas em dois sentidos verticais variados (nivelado, abaixo) numa guia personalizada contendo quatro molduras labiais do sorriso (fino, médio, grosso, invertido). Os aspectos que influenciam a atratividade do sorriso (PD = proporção dentária, PV = posicionamento vertical dentário, EL = espessura labial, FG = festonamento gengival) também foram incluídos e uma nota final geral atribuída ao sorriso geral (SG). Adicionalmente, o formulário do exercício continha a opção "existe um implante?" e "qual sua localização?". Todos os itens foram avaliados através de escalas de Likert. A prevalência de respostas foi calculada para cada item. O teste de Wilcoxon (alfa = 5%) foi usado para verificar a possibilidade de diferença de opinião entre os nivelamentos horizontais e para uma mesma moldura de sorriso. Os níveis de confiabilidade (concordância absoluta = ICC e responsividade = Cronbach alfa) também foram avaliados. Resultados: um teste-piloto foi conduzido com 16 estudantes. Trinta e duas combinações foto/moldura labial foram geradas e apresentadas de forma randomizada. A avaliação geral do sorriso ficou em: pobre (11/32), mediano (6/32), bom (15/32) e muito bom (1/32). O número de acertos da possível posição do implante foi 13 em 32 tentativas. Diferenças estatisticamente significativas entre os nivelamentos foram observadas nas situações 1/17 (p=0,0001), 13/29 (p=0,02), 2/18 (p=0,0002), 6/22 (p=0,0001), 14/30 (p=0,0001), 7/23 (p=0,01) e 15/31 (p=0,039). Os maiores coeficientes de ICC e Cronbach alfa foram vistos para o sorriso geral e FG. Conclusão: a percepção visual do dentista pode ser treinada mudando-se a moldura labial e o nivelamento vertical dos dentes e é influenciada pelo festonamento gengival. O teste se mostrou útil na verificação da atratividade do sorriso.

Objectives: to improve the perception of the dentist on the smile attractiveness through objective evaluations. Material and methods: frontal photographs of smiles (involving the canine area) were randomly chosen and arranged in two different vertical directions (leveled, below) in a personalized guide containing four lip architectures (thin, medium, thick, inverted). The aspects that infl uence the smile attractiveness (PD = dental proportion, PV = vertical tooth position, EL = lip thickness, GS = gingival scalloping) were also included and a general final score attributed to the general smile (SA). Additionally, the exercise form contained questions such as "is there an implant?" and "what is your location?". All items were assessed using Likert scales. The prevalence of responses was calculated for each item. The Wilcoxon test was used to verify the possibility of differences between the horizontal leveling for the same smile architecture. The reliability levels (absolute agreement = ICC and responsiveness = Cronbach alpha) were also evaluated. Results: a pilot test was conducted with 16 students. Thirty-two photos/lip architecture combinations were generated and presented at random. The overall smile rating was: poor (11/32), average (6/32), good (15/32), and very good (1/32). The number of positive responses for implant position was 13 in 32 trials. Statistically significant differences were observed in the combinations 1/17 (p=0.0001), 13/29 (p=0.02), 2/18 (p=0.0002), 6/22 (p=0.0001), 14/30 (p=0.0001), 7/23 (p=0.01) and 15/31 (p=0.039). The highest ICC and Cronbach alpha values were seen for the general smile attractiveness (SA) and GS. Conclusion: the visual perception can be trained by changing the lip architecture and vertical leveling of the teeth and is influenced by gingival scalloping. This test proved to be useful in verifying the smile attractiveness.

Assuntos

RESUMO

BACKGROUND: The biomechanical behavior of implant-supported titanium and zirconia full-arch fixed dental prosthesis (FAFDP) frameworks require further investigation. PURPOSE: Strains transferred by implant-supported titanium (Ti) and zirconia (Zr) FAFDP frameworks were analyzed. MATERIALS AND METHODS: Maxillary 14-unit FAFDPs supported by 6 implants and 12-unit FAFDPs supported by 4 implants were tested. One-piece frameworks were fabricated by computer-aided design/computer-aided manufacturing. Four groups were divided (n = 3): G1, Ti-6 implants; G2, Zr-6 implants; G3, Ti-4 implants; G4, Zr-4 implants. A 250 N single-point load was applied on the second premolar. A three-dimensional digital image correlation system recorded framework and maxilla model surface deformation. RESULTS: The following strains (µS) averaged over the length of the second premolar were calculated: frameworks, G1 (321.82 ± 111.29), G2 (638.87 ± 108.64), G3 (377.77 ± 28.64), G4 (434.18 ± 132.21); model surface, G1 (473.99 ± 48.69), G2 (653.93 ± 45.26), G3 (1082.50 ± 71.14), G4 (1218.26 ± 230.37). Zirconia frameworks supported by 6 implants (G2) presented higher surface strains (P < .05). FAFDPs with titanium frameworks transferred significantly lower strains to the supporting maxilla when 6 implants were used (G1) (P < .05). Both framework materials transferred similar strains when supported by 4 implants (G3 and G4) (P > .05). CONCLUSIONS: Zirconia frameworks supported by 6 implants showed higher strains. FAFDPs supported by 6 implants transferred less strains to the supporting maxilla, irrespective of framework material.

Assuntos

RESUMO

The aim of this study was to assess the effect of a diamond-like carbon (DLC) coating on the removal torque of prefabricated implant screws after cyclic loading. Four groups with two crowns supported by two implants (n = 5) were obtained according to splinted and nonsplinted prosthesis, using titanium or DLC screws (splinted crowns with titanium screw [STi], splinted crowns with DLC screw [SC], nonsplinted crowns and titanium screw [NSTi], and nonsplinted crowns and DLC screw [NSC]). The prosthetic screws were tightened at 32 Ncm and retightened, and the specimens were submitted to 106 mechanical cycles (4 Hz/98 N). After cyclic loading, loosening torque was evaluated, and the final measurements were performed. Data were analyzed by two-way analysis of variance and Tukey's test (α = .005). There was statistically significance in the interaction of screw × splinting (P = .003). For the group that used titanium screws, NSTi showed smaller removal torque compared with STi. It was concluded that the use of the DLC coating screws in nonsplinted prosthesis maintain the torque after cyclic loading.

Assuntos

RESUMO

Objetivo: avaliar, por meio de um microdurômetro, o grau de desajuste na adaptação de pilares Ucla em implantes. Material e métodos: foram utilizados dez implantes de hexágono interno de plataforma regular, e seus respectivos componentes protéticos do tipo Ucla com antirrotacional, como seguem: dez pilares Ucla totalmente calcináveis e dez pilares Ucla com base de CoCr. Todos os pilares Ucla foram fundidos pelo mesmo laboratório de prótese e pelo mesmo processo laboratorial. Cada implante recebeu apenas dois pilares, que foram anexados por meio de um parafuso de titânio quadrado utilizando-se torque de 30 Ncm com torquímetro manual. Cada conjunto implante/pilar recebeu quatro marcações aleatórias em torno da circunferência, na qual foram feitas as medições do espaço existente entre as peças utilizando uma lupa estereoscópica de 100 vezes de aumento. Resultados: os resultados obtidos mostraram diferenças significativas entre os grupos submetidos ao teste Mann-Whitney (p < 0,05). Conclusão: o pilar Ucla com base de CoCr apresentou menor desajuste marginal vertical, quando comparado ao pilar Ucla totalmente calcinável, após o processo de fundição nos implantes de hexágono interno.

Objective: to evaluate, using a microhardness device, the misfit between Ucla abutments and internal hex implants. Material and methods: 10 internal hex implants received 10 Ucla burnout and 10 Ucla abutments with CoCr collar. All the abutments were cast in the same laboratory and under the same protocol. A square-head titanium screw was tightened to a 30 Ncm using a manual wrench. Each abutment/implant set receive four random markings around its perimeter. A stereoscopic lens was used to investigate the misfi t at 100 magnification. Results: there was a statistically significant difference between tested abutments (Mann-Whitney p < 0.05). Conclusion: the Ucla abutment with the CoCr collar presented less vertica misfit values after casting for internal hex dental implants.

Assuntos

RESUMO

En la rehabilitación odontológica integral actual, hay que evaluar los parámetros clínicos para una restauración sobre implantes dentales. El tratamiento del sector anterior de ambos maxilares en situaciones clínicas complejas, hace que el éxito sea difícil de alcanzar, inclusocuando todos los objetivos establecidos de diagnóstico y de planificación del tratamiento, sean respetados y puedan realizarse. El objetivo es imitar la apariencia de los dientes contiguos para simular la dentición natural, con un enfoque en la estética de los tejidos gingivales adyacentes a las restauraciones sobre implantes. En los casos en que el tejido óseo y la pérdida mucogingivales marcada y procedimientos quirúrgicos adicionales no son viables, se requerirá de tratamientos alternativos. Uno de ellos podría ser el uso de encía artificial para reconstruir las deficiencias de tejidos duros y blandos. Este artículo describe diferentes indicaciones y aplicaciones clínicas de la encía artificial en prótesis implanto asistida.

In the current comprehensive dental rehabilitation, clinical parameters for success restoration on dental implants must be evaluated.Treatment of both anterior maxillary and mandibular jaws in complex clinical situations makes success difficult to achieve, even when allestablished goals in diagnosis and treatment planning, are respected and can be made.The goal is to mimic the appearance of the adjacent teeth to simulate natural dentition, with a focus on the aesthetics of the gingival tissuesnext to implant restorations. In cases where the bone and mucogingival tissues loss are marked and additional surgical procedures shouldnot be viable, it will require alternative treatment options. One of them could be the use of artificial gingiva to rebuild the deficiencies ofhard and soft tissues.This article describes different indications and clinical applications in artificial gum assisted implant prosthesis.

Assuntos

RESUMO

Framework misfit is a common problem observed in overdentures, which might result in prosthetic and biological complications. The aim of this study was to evaluate the influence of vertical misfit and clip material on the stress distribution in an overdenture-retaining bar system under masticatory loading. A 3-D finite element model of a resorbed jaw was created, including two implants and a bar-clip retained overdenture. A pressure of 100 MPa was applied to the right mandibular first molar. Different vertical misfit levels (50, 100, and 200 µm) and clip materials (plastic or gold) were evaluated. Data were evaluated using von Mises stress and microstrain. Vertical misfit amplification caused an increase in the microstrain values in the peri-implant bone tissue next to the ill-fitted component and increased the stresses in the prosthetic screws. The clip material influenced the stress and microstrain distribution in the prosthetic components and bone tissue. The levels of vertical misfit seem to be closely linked with the stress values in the prosthetic screws, mainly to that of the ill-fitted component. The gold clip presented an increase in the stress compared to the plastic clip.

Assuntos

RESUMO

OBJECTIVES: The aim of this study was to evaluate the quality of life and satisfaction of patients wearing implant-supported fixed partial dentures. MATERIALS & METHODS: A total of 106 patients were selected and submitted to clinical examination and collection of the demographic data for evaluation of the implant-supported fixed dentures conditions. All participants agreed to answer to the Oral Health Impact Profile (OHIP-EDENT) questionnaire and another questionnaire about satisfaction with the implant-supported prostheses. The patients were classified into the following three groups for statistical analysis: patients wearing splinted implant-supported prosthesis (E), patients wearing single implant-supported prosthesis (U), and patients wearing single implant-supported prosthesis associated with splinted prosthesis (E + U). Kruskal-Wallis test was used to compare the answers between the groups, and a logistic regression model was measured to verify the relation between variables of the patients and the questionaries' items. RESULTS: There were significant differences among groups (P = 0.006) for discomfort during surgery itself of the satisfaction questionnaire. The marital status, groups, and hygiene condition were significant mainly for physical pain item. CONCLUSIONS: It was concluded that the patients presented high level of satisfaction and quality of life for the most of the items evaluated as well as the groups showed similar results.

Assuntos

RESUMO

BACKGROUND: Fixed implant-supported prostheses according to All-on-Four® (Nobel Biocare, Goteborg, Sweden) principles have become an accepted treatment modality in totally edentulous patients, whereas the functional effect of this therapy is limited. PURPOSE: The purpose of this study was to evaluate the muscular function of patients totally rehabilitated with All-on-Four. MATERIALS AND METHODS: This study evaluated 63 patients. Twenty-one patients were successfully rehabilitated with maxillary and mandibular All-on-Four (no dropout implants, satisfactory aesthetic and function demands prosthesis), 21 patients were dentate, and 21 were rehabilitated with double complete dentures. Electromyography was carried out during clenching, nonhabitual and habitual chewing, and rest. All values were standardized as percentage of a maximum voluntary contraction. Data were analyzed by ANOVA to compare groups and paired t-test was used for comparison between sides within each group. RESULTS: All groups presented symmetric muscular activity. The All-on-Four and dentate groups had a similar muscles surface electromyography (sEMG) contraction pattern, that is, a higher sEMG activity of masseter than temporalis muscles, differing (p ≤ .05) from those of denture group. Not one statistical difference was found between All-on-Four and dentate groups. CONCLUSION: The muscular function similarity of All-on-Four and dentate patients shows that this treatment concept may be considered as a good option for oral rehabilitation in edentulous patients.

Assuntos

RESUMO

This study evaluated the influence of cross-section geometry of the bar framework on the distribution of static stresses in an overdenture-retaining bar system simulating horizontal misfit and bone loss. Three-dimensional FE models were created including two titanium implants and three cross-section geometries (circular, ovoid or Hader) of bar framework placed in the anterior part of a severely resorbed jaw. One model with 1.4-mm vertical loss of the peri-implant tissue was also created. The models set were exported to mechanical simulation software, where horizontal displacement (10, 50 or 100 µm) was applied simulating the settling of the framework, which suffered shrinkage during the laboratory procedures. The bar material used for the bar framework was a cobalt--chromium alloy. For evaluation of bone loss effect, only the 50-µm horizontal misfit was simulated. Data were qualitatively and quantitatively evaluated using von Mises stress for the mechanical part and maximum principal stress and µ-strain for peri-implant bone tissue given by the software. Stresses were concentrated along the bar and in the join between the bar and cylinder. In the peri-implant bone tissue, the µ-strain was higher in the cervical third. Higher stress levels and µ-strain were found for the models using the Hader bar. The bone loss simulated presented considerable increase on maximum principal stresses and µ-strain in the peri-implant bone tissue. In addition, for the amplification of the horizontal misfit, the higher complexity of the bar cross-section geometry and bone loss increases the levels of static stresses in the peri-implant bone tissue.

Assuntos

RESUMO

Com a evolução da Implantodontia, há uma demanda crescente por alternativas de tratamento que possibilitem menor tempo para a resolução dos casos clínicos. Uma oclusão bem equilibrada e protocolos de carregamento adequados desempenham um papel fundamental no sucesso e na longevidade dos implantes e das próteses. O presente trabalho visou, por meio de uma revisão da literatura atual, reportar a evolução dos conceitos de oclusão e dos protocolos de carregamento aplicados aos casos reabilitados com implantes unitários nas regiões posteriores de mandíbula e maxila. Apesar da falta de consenso, a literatura, de modo geral, sugere prudência ao adotar protocolos de carregamento imediato ou precoce de implantes unitários, preferencialmente evitando contatos oclusais durante o período de osseointegração.

Recent advances on Implant Dentistry led to an increasing demand for alternatives with less chairside time to finish clinical cases. A well balanced occlusion and adequate loading protocols play a fundamental role on the success and longevity of implants and prostheses. The present paper aims to report, through a review of the current literature, the evolution of the concepts regarding occlusion and loading protocols applied to clinical cases using single-tooth implants on posterior regions. Despite the absence of a consensus about the theme, the current literature suggests, in general, caution when choosing to adopt immediate or premature loading of single-tooth implants placed on posterior regions, preferably avoiding occlusal loads during the osseointegration period.

Assuntos

RESUMO

This study evaluated the influence of retorque on loosening torque (Lt) of prosthetic screws in implant-supported dentures with different fit levels. Ten mandibular implant-supported dentures were fabricated and then 20 cast models were then prepared using prosthetic structures to create 2 fit levels: passive fit (Pf) and misfit (Mf). Two tightening techniques were also evaluated: initial torque only (T1); and initial torque and retorque after 10 min (T2). Gold or titanium screws were used, resulting in 4 groups to each one: Pf/T1, Pf/T2, Mf/T1, Mf/T2. The Lt was measured 24 h after the tightening torque using digital torque meter. Data were analyzed statistically by two-way ANOVA and Tukey's test (α=0.05), separately for each screw material. For titanium screws, no significant difference (p>0.05) was found between Pf/T1 and Pf/T2, or between Pf/T2 and Mf/T2. However, statistically significant difference (p<0.05) was found between Pf/T1 and Mf/T1, and between Mf/T1 and Mf/T2. Mf reduced the Lt using T1, while and T2 increased the Lt for Mf. Retorque and fit were shown to have no significant influence on the Lt of the gold screws. Retorque application made insignificant the misfit effect on the Lt of the titanium screws, suggesting that this procedure should be performed routinely during the screw tightening in multi-unit dentures.

Este estudo avaliou a influência do retorque no Ta dos parafusos protéticos em próteses implantossuportadas com diferentes níveis de adaptação. Foram confeccionadas 10 próteses mandibulares implantossuportadas. Vinte modelos de gesso foram fabricados utilizando as estruturas protéticas para criar os 2 níveis de adaptação: adaptação passiva (AP) e desajuste (D). Foram avaliadas 2 técnicas de aperto do parafuso: inicial torque (T1); e inicial torque e retorque após 10 min (T2). Foram usados parafusos de ouro e titânio, resultando em 4 grupos para cada material do parafuso: AP/T1, AP/T2, D/T1, D/T2. O Ta foi mensurado 24 h após o torque de aperto utilizando torquímetro digital. Os resultados foram analisados pela ANOVA (2 fatores) e teste de Tukey (α=0,05), separadamente para cada material dos parafusos. Para os parafusos de titânio, não foi encontrada diferença estatística significante entre AP/T1 e AP/T2, ou AP/T2 e D/T2; porém, diferença significante foi encontrada entre AP/T1 e D/T1, ou D/T1 e D/T2. Onde, D reduziu a Ta utilizando T1; e T2 aumentou o Ta para D. Retorque e adaptação não apresentaram influência significante no Ta dos parafusos de ouro. A aplicação do retorque tornou insignificante o efeito do desajuste no Ta dos parafusos de titânio, sugerindo que este procedimento deveria ser usado rotineiramente durante os parafusos protéticos de titânio em próteses múltiplas.

Assuntos

RESUMO

Restaurações implantossuportadas em zonas estéticas anteriores apresentam desafios significativos, tanto na fase cirúrgica quanto na fase protética. A importância dos valores estéticos para a sociedade moderna tem se refletido na Odontologia: os pacientes procuram por soluções não somente funcionais, mas, também, com excelência em estética, o que se transforma num desafio cada vez maior. Uma transição harmoniosa entre a restauração e os tecidos peri-implantares é extremamente importante. A aparência de saúde gengival consiste numa coloração natural e, também, num apropriado contorno gengival. Em relação a esse, os pilares de titânio vêm atingindo bons resultados, quando a qualidade e a quantidade de gengiva inserida estão presentes. Porém, à medida que essa é diminuída, os resultados estéticos, utilizando os pilares metálicos, ficam mais distantes. Alguns dos recursos utilizados nessas condições, objetivando a estética, são os pilares cerâmicos. Esses pilares unem resistência e estética, além de biocompatibilidade com os tecidos peri-implantares. Outra vantagem é que possibilitam a aplicação direta da porcelana, quando a indicação recai sobre uma prótese parafusada.

Implant supported restorations in anterior esthetical areas are a great challenge, both in the surgical as in the prosthetic phases. The importance of esthetical values for modern society has been reflected in Dentistry: patients are looking not only for functional but also esthetical solutions, what makes the challenge even bigger. A harmonious transition between restorations and perimplant tissues is extremely important. The healthy appearance of gingiva includes a natural color and an appropriate contour. Related to this, the titanium abutments are achieving good results, concerning the quality and quantity of attached gingiva. Meanwhile, if the gingiva conditions get worse, the esthetical results using metalic abutments may be compromised. In these situations, ceramic abutments can improve esthetical condition. These abutments have both resistance and esthetic, as well as biocompatibility with perimplant tissues. Another advantage is the possiblity of direct application of porcelain in the abutment, in case of screw retained prosthesis.

Assuntos

RESUMO

OBJECTIVES: This study evaluated the influence of prosthetic screw material on joint stability in implantsupported dentures at two levels of fit. METHODS: Ten mandibular implant-supported dentures were fabricated. Twenty cast models were fabricated using these dentures. Four groups (n=10) were tested, according to the vertical fit of the dentures [passive and non-passive] and prosthetic screw materials [titanium (Ti) or gold (Au) alloy]. The one-screw test was performed to quantify the vertical misfits using an optic microscope. The loosening torque for the prosthetic screws was measured 24 hours after the tightening torque (10 Ncm) using a digital torque meter. Data were analyzed by two-way ANOVA and Tukey's test (alpha=0.05). RESULTS: Overall, dentures with passive fit and Ti screws resulted in significantly higher loosening torque of the prosthetic screws (p<0.05). No significant interaction was found between fit level and screw material (p=0.199). The prosthetic screw material and fit of implant-supported dentures have an influence on screw joint stability. Ti screws presented higher joint stability than Au screws and minimum of misfit should be found clinically to improve the mechanical behavior of the screw joint.

RESUMO

Actualmente el uso de prótesis sobre implantes se incrementó gradualmente desde el descubrimiento de la oseointegración. La indicación inicial de los implantes fue para pacientes edéntulos totales extendiéndose después para pacientes parcialmente edéntulos. Las alternativas de retención de las piezas protésicas van desde las prótesis atornilladas hasta las prótesis cementadas o por preparación de los pilares de la forma convencional. Las prótesis cementadas sobre implantes se utilizan frecuentemente en los casos donde la inclinación de los implantes imposibilita la confección de prótesis atornilladas, debido a la salida de los tornillos de fijación por vestibular o entre los espacios interdentales comprometiendo la estética, y la resistencia cuando están localizados en las cúspides oclusales de los dientes posteriores. En ese sentido, la confección de "copings" en los pilares preparados, puede tornar el tratamiento en un proceso más rápido y seguro. No obstante, pueden surgir problemas en el momento de la instalación, debido a que el intermediario puede asumir diversas posiciones en relación a la posición del implante dificultando la colocación de la prótesis definitiva, principalmente en situaciones clínicas con más de dos implantes. De este modo, el objetivo de este trabajo fue mostrar una técnica del uso de una guía para posicionamiento de los pilares protésicos en prótesis fija cementada sobre implantes, por medio de la descripción de un caso clínico

Nowadays, the use of implant-retained prostheses has been increasing progressively since the advent of the osseointegration. The basic indication was in total edentulous patients and it was also enlarged for partially edentulous patients. Alternatives of retention could be from screw-retained implant prostheses, cement-retained implant prostheses or conventional preparations. Cement-retained implant prostheses are used frequently when the implant inclination don't allow the use of screw-retained prostheses because the screw emerge in vestibular surface or the interdental space resulting in an unaesthetic appearance and when the screw emerge on the top of the posterior cuspid teeth, diminishing the resistance. The confection of the copings on the abutments, turn the treatment faster and secure. Although, some complications can appear in the placement, because the abutment can take different positions in relation to the implant modifying the set of the prosthesis, mainly in clinical situations with more than two implants support. Thus, the aim of this study was demonstrated the use of guide to positioning of cement-retained implant prostheses, by means of a clinical case

Assuntos

RESUMO

A doença periodontal acarreta na perda óssea e conseqüente perda dentária. Este quadro clínico dificulta o restabelecimento funcional e estético, especialmente nas áreas anteriores da maxila. No entanto, o restabelecimento da anatomia óssea é proporcionado pelo procedimento de enxertia óssea, objetivando futura instalação de implantes, permitindo devolver estética e função. O plasma rico em plaquetas (PRP) mostrou ser um material autógeno, de fácil obtenção e processamento, podendo acelerar o processo de reparo ósseo. O caso clínico apresentado, conjugou o procedimento de enxertia óssea com o uso do plasma rico em plaquetas (PRP) para otimização deste procedimento. Restabelecendo o contorno ósseo para otimização do tratamento com implantes dentários

The periodontal disease causes bono loss, and subsequent dental loss. This clinical situation impairs functional and esthetic reconstruction, especially in anterior maxillary areas. Therefore, the bone anatomy reestablishment is given by bone graft augmentation procedure, aiming future implant placement, devolving esthetic and function. The platelet-rich-plasma (PRP) has been an autogenous material, easy to obtain and process, being capable of speeding the bone healing. The clinical case presented, combined the bone graft procedure with platelet-rich-plasma (PRP) to optimize dental implant therapy

Assuntos