RESUMO

The global focus on incorporating natural ingredients into the diet for health improvement encompasses ω-3 polyunsaturated fatty acids (PUFAs) derived from plant sources, such as flaxseed oil. ω-3 PUFAs are susceptible to oxidation, but oil-in-water (O/W) emulsions can serve to protect PUFAs from this phenomenon. This study aimed to create O/W emulsions using flaxseed oil and either soy lecithin or Quillaja saponins, thickened with modified starch, while assessing their physical properties (oil droplet size, ζ-potential, and rheology) and physical stability. Emulsions with different oil concentrations (25% and 30% w/w) and oil-to-surfactant ratio (5:1 and 10:1) were fabricated using high-pressure homogenization (800 bar, five cycles). Moreover, emulsions were thickened with modified starch and their rheological properties were measured. The physical stability of all emulsions was assessed over a 7-day storage period using the TSI (Turbiscan Stability Index). Saponin-stabilized emulsions exhibited smaller droplet diameters (0.11-0.19 µm) compared to lecithin (0.40-1.30 µm), and an increase in surfactant concentration led to a reduction in droplet diameter. Both surfactants generated droplets with a high negative charge (-63 to -72 mV), but lecithin-stabilized emulsions showed greater negative charge, resulting in more intense electrostatic repulsion. Saponin-stabilized emulsions showed higher apparent viscosity (3.9-11.6 mPa·s) when compared to lecithin-stabilized ones (1.19-4.36 mPa·s). The addition of starch significantly increased the apparent viscosity of saponin-stabilized emulsions, rising from 11.6 mPa s to 2117 mPa s. Emulsions stabilized by saponin exhibited higher stability than those stabilized by lecithin. This study confirms that plant-based ingredients, particularly saponins and lecithin, effectively produce stable O/W emulsions with flaxseed oil, offering opportunities for creating natural ingredient-based food emulsions.

RESUMO

Opuntia silvestri mucilage obtained from dried stems was explored as an emulsifier to prepare double emulsions aiming to encapsulate Lactiplantibacillus plantarum CIDCA 83114. W1/O/W2 emulsions were prepared using a two-step emulsification method. The aqueous phase (W1) consisted of L. plantarum CIDCA 83114, and the oil phase (O) of sunflower oil. The second emulsion was prepared by mixing the internal W1/O emulsion with the W2 phase, consisting of 4 % polysaccharides, formulated with different mucilage:(citric)pectin ratios. Their stability was assessed after preparation (day 0) and during storage at 4 °C (28 days). Determinations included creaming index, color, particle size, viscosity, turbidity, and bacterial viability, along with exposure to simulated gastrointestinal conditions. Significant differences were evaluated by analysis of variance (ANOVA) and Duncan's test (P < 0.05). After 28 days storage, bacterial viability in the W1/O/W2 emulsions was above 6 log CFU/mL for all the pectin:mucilage ratios. Emulsions containing mucilage and pectins showed lower creaming indices after 15 days, remaining stable until the end of the storage period. Formulations including 1:1 pectin:mucilage ratio exhibited the highest bacterial viability under simulated gastrointestinal conditions and were more homogeneous in terms of droplet size distributions at day 0, hinting at a synergistic effect between mucilage components (e.g., proteins, Ca2+) and pectin in stabilizing the emulsions. These results showed that Opuntia silvestri mucilage enhanced the stability of emulsions during refrigerated storage, highlighting its potential for encapsulating lactic acid bacteria. This presents an economical and natural alternative to traditional encapsulating materials.

Assuntos

RESUMO

Microbial bioemulsifiers are molecules of amphiphilic nature and high molecular weight that are efficient in emulsifying two immiscible phases such as water and oil. These molecules are less effective in reducing surface tension and are synthesized by bacteria, yeast and filamentous fungi. Unlike synthetic emulsifiers, microbial bioemulsifiers have unique advantages such as biocompatibility, non-toxicity, biodegradability, efficiency at low concentrations and high selectivity under different conditions of pH, temperature and salinity. The adoption of microbial bioemulsifiers as alternatives to their synthetic counterparts has been growing in ongoing research. This article analyzes the production of microbial-based emulsifiers, the raw materials and fermentation processes used, as well as the scale-up and commercial applications of some of these biomolecules. The current trend of incorporating natural compounds into industrial formulations indicates that the search for new bioemulsifiers will continue to increase, with emphasis on performance improvement and economically viable processes.

Assuntos

RESUMO

Lindane and other 1,2,3,4,5,6-hexachlorocyclohexane (HCH) isomers are persistent organic pollutants highly hydrophobic, which hampers their availability and biodegradation. This work aimed at (i) investigating genes encoding enzymes involved in HCH degradation in the bacterium Sphingobium sp. D4, (ii) selecting strains, from a collection of environmental isolates, able to mobilize HCHs from contaminated soil, and (iii) analysing the biodegradation of HCHs by strain D4 in co-culture with HCH-mobilizing strains or when cultivated with root exudates. Fragments of the same size and similar sequence to linA and linB genes were successfully amplified. Two isolates, Streptomyces sp. M7 and Rhodococcus erythropolis ET54b able to produce emulsifiers and to mobilize HCH isomers from soil were selected. Biodegradation of HCH isomers by strain D4 was enhanced when co-inoculated with HCH mobilizing strains or when cultivated with root exudates. The degrader strain D4 was able to decompose very efficiently HCHs isomers, reducing their concentration in soil slurries by more than 95% (from an average initial amount of 50 ± 8 mg HCH kg-1 soil) in 9 days. The combination of HCH-degrading and HCH-mobilizing strains can be considered a promising inoculum for future soil bioremediation studies using bioaugmentation techniques or in combination with plants in rhizodegradation assays.

Assuntos

RESUMO

In food formulations, lipids are normally incorporated as emulsions stabilized by different types of emulsifiers. The emulsifiers can affect fatty acid (FA) solubilization as they can interact with FA. The main purpose of the present work is the development of a methodology to evaluate the FA solubilization in an aqueous medium in the absence and presence of exogenous emulsifiers. To this end, a combination of turbidimetry, oiling off and dynamic light scattering (DLS) was used. The FA solubility, as well as its supramolecular assemblies, were determined by analyzing the changes in the turbidity profile and the corresponding size of particles obtained by DLS. Oleic acid (OA) was used as a model FA and a simulated intestinal fluid (SIF) as the aqueous phase. Emulsifiers of low (Tween 80) and high (protein and polysaccharide) molecular weight were tested. Tween 80 was the only emulsifier that improved OA solubilization, whereas the macromolecules only affected the supramolecular structure that OA adopted, being the structure of these assemblies governed by the emulsifier nature.

Assuntos

RESUMO

There has been considerable interest in the use of biosurfactants due to the diversity of structures and the possibility of production from a variety of substrates. The potential for industrial applications has been growing, as these natural compounds are tolerant to common processing methods and can compete with synthetic surfactants with regards to the capacity to reduce surface and interfacial tensions as well as stabilise emulsions while offering the advantages of biodegradability and low toxicity. Among biosurfactant-producing microorganisms, some yeasts present no risks of toxicity or pathogenicity, making them ideal for use in food formulations. Indeed, the use of these biomolecules in foods has attracted industrial interest due to their properties as emulsifiers and stabilizers of emulsions. Studies have also demonstrated other valuable properties, such as antioxidant and antimicrobial activity, enabling the aggregation of greater value to products and the avoidance of contamination both during and after processing. All these characteristics allow biosurfactants to be used as additives and versatile ingredients for the processing of foods. The present review discusses the potential application of biosurfactants as emulsifying agents in food formulations, such as salad dressing, bread, cakes, cookies, and ice cream. The antioxidant, antimicrobial and anti-adhesive properties of these biomolecules are also discussed, demonstrating the need for further studies to make the use of the natural compounds viable in this expanding sector.

Assuntos

RESUMO

During the last decade a special interest has been focused on studying the relationship between the composition and structure of emulsions and the extent of lipolysis, driven by the necessity of modulate lipid digestion to decrease or delay fats absorption or increase healthy fat nutrients bioavailability. Because bile salts (BS) play a crucial role in lipids metabolism, understanding how typical food emulsifiers affect the structures of BS under duodenal conditions, can aid to further understand how to control lipids digestion. In the present work the BS-binding capacity of three emulsifiers (Lecithin, Tween 80 and ß-lactoglobulin) was studied under duodenal conditions. The combination of several techniques (DLS, TEM, ζ-potential and conductivity) allowed the characterization of molecular assemblies resulting from the interactions, as modulated by the relative amounts of BS and emulsifiers in solution.

Assuntos

RESUMO

Microemulsions are thermodynamically stable systems that have attracted considerable attention in the food industry as delivery systems for many hydrophobic nutrients. These spontaneous systems are highly dependent on ingredients and composition. In this work phase diagrams were constructed using two surfactants (Kolliphor RH40 and ELP), water, sunflower oil, and ethanol as cosurfactant, evaluating their physicochemical properties. Stability of the systems was studied at 25 and 60 °C, monitoring turbidity at 550 nm for over a month to identify the microemulsion region. Conductivity was measured to classify between water-in-oil and oil-in-water microemulsions. The phase diagram constructed with Kolliphor RH40 exhibited a larger microemulsion area than that formulated with Kolliphor ELP. All formulations showed a monomodal droplet size distribution with low polydispersity index (<0.30) and a mean droplet size below 20 nm. Systems with higher water content presented a Newtonian behavior; increasing the dispersed phase content produced a weak gel-like structure with pseudoplastic behavior under flow conditions that was satisfactorily modeled to obtain structural parameters.

Assuntos

RESUMO

The relationship between the composition and structure of food emulsions was evaluated from the effect of a mixture of emulsifiers Whey protein (WPI) - Tween 80 (T80) and the oil phase features, such as chain length and unsaturation degree (sunflower oil, a long chain triacylglycerol - LCT or NEOBEE® 1053, a medium chain triacylglycerol - MCT). Emulsions with LCT showed higher droplet size than MCT as a consequence of its higher viscosity. All emulsions exhibited shear thinning behavior, but the viscosity was influenced by their interface composition. An occurrence of the destabilization mechanism by creaming was observed in turbidimetric measurements, but no visual phase separation could be observed, indicating a good kinetic stability after a 7-day storage. The initial interfacial tension of the water-LCT or water-MCT oil was about 25 mN/m, but the WPI addition (1% w/w) reduced the initial interfacial tension to approximately 20 mN/m. The increase of T80 concentration led to a decrease of the interfacial tension, reaching a value around 10 mN/m in systems with pure T80. The curves of interfacial tension of systems with LCT or MCT showed differences in the decay rate of tension over time. These differences were attributed to characteristics of the oil phase (hydrophobicity, unsaturation degree, presence of impurities) and the different proportions of each emulsifier within the mixture of emulsifiers. Finally, a higher viscoelastic interface was observed in LCT emulsions, which were mainly stabilized by WPI molecules. Such molecules presented a higher resistance to the displacement due to the competitive adsorption phenomenon, since the LCT is a more hydrophobic oil. On the other hand, the interface with MCT and a higher T80 concentration was less viscoelastic due to an easier displacement of WPI from the interface and the replacement by T80. The results indicate that T80 can be used in combination with WPI to produce emulsions with good stability and lower concentration of synthetic compounds. Lastly, the interfacial layer composition is not only dependent on the WPI-T80 ratio in the bulk phase, but also on the oily phase features. These results provide a potential strategy for designing emulsified foods based on the choice of ingredients and knowledge of the interaction between them.

Assuntos

RESUMO

Background: Surfactants are one of the most important raw materials used in various industrial fields as emulsifiers, corrosion inhibitors, foaming agents, detergent products, and so on. However, commercial surfactant production is costly, and its demand is steadily increasing. This study aimed to evaluate the performance of typical strains of Bacillus sp. to produce biosurfactants through fermentation. It also included the investigation of the effect of initial glucose concentration and the carbon to nitrogen ratio. Results: The biosurfactant yield was in the range of 1­2.46 g/L at initial glucose concentrations of 10­70 g/L. The optimum fermentation condition was achieved at a carbon to nitrogen ratio of 12.4, with a decrease in surface tension of up to 27 mN/m. Conclusions: For further development and industrial applications, the modified Gompertz equation is proposed to predict the cell mass and biosurfactant production as a goodness of fit was obtained with this model. The modified Gompertz equation was also extended to enable the excellent prediction of the surface tension.

Assuntos

RESUMO

Carbohydrate fatty acid esters are non-ionic surfactants with a broad spectrum of applications. These molecules are generally synthesized using short carbohydrates or linear fructans; however in this research carbohydrate fatty acid esters were produced for the first time with branched fructans from Agave tequilana. Using immobilized lipases we successfully acylated A. tequilana fructans with vinyl laurate, obtaining products with different degrees of polymerization (DP). Lipozyme 435 was the most efficient lipase to catalyze the transesterification reaction. HPLC and ESI-MS analysis proved the presence of a mixture of acylated products as a result of the chemical complexity of fructans in the A. tequilana. The ESI-MS spectra showed a molecular mass shift between 183 and 366g/mol for fructooligosaccharides with a DP lower than 6, which indicated the presence of Agave fructans that had been mono- and diacylated with lauric acid. The carbohydrate fatty acid esters (CFAE) obtained showed good emulsifying properties in W/O emulsions.

Assuntos

RESUMO

Crystallization of fats is a determinant physical event affecting the structure and properties of fat-based products. The stability of these processed foods is regulated by changes in the physical state of fats and alterations in their crystallization behavior. Problems like polymorphic transitions, oil migration, fat bloom development, slow crystallization and formation of crystalline aggregates stand out. The change of the crystallization behavior of lipid systems has been a strategic issue for the processing of foods, aiming at taylor made products, reducing costs, improving quality, and increasing the applicability and stability of different industrial fats. In this connection, advances in understanding the complex mechanisms that govern fat crystallization led to the development of strategies in order to modulate the conventional processes of fat structuration, based on the use of crystallization modifiers. Different components have been evaluated, such as specific triacyglycerols, partial glycerides (monoacylglycerols and diacylglycerols), free fatty acids, phospholipids and emulsifiers. The knowledge and expertise on the influence of these specific additives or minor lipids on the crystallization behavior of fat systems represents a focus of current interest for the industrial processing of oils and fats. This article presents a comprehensive review on the use of crystallization modifiers in lipid systems, especially for palm oil, cocoa butter and general purpose fats, highlighting: i) the removal, addition or fractionation of minor lipids in fat bases; ii) the use of nucleating agents to modify the crystallization process; iii) control of crystallization in lipid bases by using emulsifiers. The addition of these components into lipid systems is discussed in relation to the phenomena of nucleation, crystal growth, morphology, thermal behavior and polymorphism, with the intention of providing the reader with a complete panorama of the associated mechanisms with crystallization of fats and oils.

RESUMO

Os emulsificantes são aditivos empregados com diversas finalidades na produção dos alimentos industrializados, dentre elas para melhorar a textura, o volume, a aeração e a homogeneidade dos produtos. Estudos indicam mais uma função para estes compostos que atuam usualmente estabilizando emulsões, como modificadores do processo de cristalização de óleos e gorduras. Produtos como chocolates, margarinas e sorvetes são elaborados com base nos compostos gordurosos que, ao atingirem a condição de super-resfriamento ou supersaturação, formam cristais e, posteriormente, uma rede cristalina tridimensional, responsável pelos atributos sensoriais dos produtos. Os emulsificantes podem interferir no tempo de indução, na velocidade de formação dos cristais de gordura, além de modificar a morfologia e o hábito cristalino desses cristais, retardando as transições polimórficas indesejáveis e afetando diretamente a qualidade dos produtos. Esta revisão abordou os diferentes efeitos de emulsificantes utilizados em alimentos na cristalização de matérias-primas gordurosas.

The emulsifiers are additives used for many purposes in the production of foods, among them to improve texture, volume, aeration and homogeneity of the products. Most studies indicate a new role for this compound that acts usually stabilizing emulsions, as modifier of the crystallization of oils and fats. Products such as chocolate, margarine and ice cream which are made of fats, upon reaching the condition of supercooling or supersaturation, form crystals and then a three-dimensional crystal lattice responsible for sensory attributes of products. The emulsifiers can alter induction time, the rate of formation of fat crystals and modify the morphology and crystal habit of these crystals, retarding undesired polymorphic transitions and affecting quality of products. This review evaluated the effects of different food emulsifiers on the crystallization of fats.

RESUMO

Os emulsificantes são aditivos empregados com diversas finalidades na produção dos alimentos industrializados, dentre elas para melhorar a textura, o volume, a aeração e a homogeneidade dos produtos. Estudos indicam mais uma função para estes compostos que atuam usualmente estabilizando emulsões, como modificadores do processo de cristalização de óleos e gorduras. Produtos como chocolates, margarinas e sorvetes são elaborados com base nos compostos gordurosos que, ao atingirem a condição de super-resfriamento ou supersaturação, formam cristais e, posteriormente, uma rede cristalina tridimensional, responsável pelos atributos sensoriais dos produtos. Os emulsificantes podem interferir no tempo de indução, na velocidade de formação dos cristais de gordura, além de modificar a morfologia e o hábito cristalino desses cristais, retardando as transições polimórficas indesejáveis e afetando diretamente a qualidade dos produtos. Esta revisão abordou os diferentes efeitos de emulsificantes utilizados em alimentos na cristalização de matérias-primas gordurosas.

The emulsifiers are additives used for many purposes in the production of foods, among them to improve texture, volume, aeration and homogeneity of the products. Most studies indicate a new role for this compound that acts usually stabilizing emulsions, as modifier of the crystallization of oils and fats. Products such as chocolate, margarine and ice cream which are made of fats, upon reaching the condition of supercooling or supersaturation, form crystals and then a three-dimensional crystal lattice responsible for sensory attributes of products. The emulsifiers can alter induction time, the rate of formation of fat crystals and modify the morphology and crystal habit of these crystals, retarding undesired polymorphic transitions and affecting quality of products. This review evaluated the effects of different food emulsifiers on the crystallization of fats.

Assuntos

RESUMO

Os emulsificantes são aditivos empregados com diversas finalidades na produção dos alimentos industrializados, dentre elas para melhorar a textura, o volume, a aeração e a homogeneidade dos produtos. Estudos indicam mais uma função para estes compostos que atuam usualmente estabilizando emulsões, como modificadores do processo de cristalização de óleos e gorduras. Produtos como chocolates, margarinas e sorvetes são elaborados com base nos compostos gordurosos que, ao atingirem a condição de super-resfriamento ou supersaturação, formam cristais e, posteriormente, uma rede cristalina tridimensional, responsável pelos atributos sensoriais dos produtos. Os emulsificantes podem interferir no tempo de indução, na velocidade de formação dos cristais de gordura, além de modificar a morfologia e o hábito cristalino desses cristais, retardando as transições polimórficas indesejáveis e afetando diretamente a qualidade dos produtos. Esta revisão abordou os diferentes efeitos de emulsificantes utilizados em alimentos na cristalização de matérias-primas gordurosas.(AU)

The emulsifiers are additives used for many purposes in the production of foods, among them to improve texture, volume, aeration and homogeneity of the products. Most studies indicate a new role for this compound that acts usually stabilizing emulsions, as modifier of the crystallization of oils and fats. Products such as chocolate, margarine and ice cream which are made of fats, upon reaching the condition of supercooling or supersaturation, form crystals and then a three-dimensional crystal lattice responsible for sensory attributes of products. The emulsifiers can alter induction time, the rate of formation of fat crystals and modify the morphology and crystal habit of these crystals, retarding undesired polymorphic transitions and affecting quality of products. This review evaluated the effects of different food emulsifiers on the crystallization of fats.(AU)

Assuntos