RESUMO

Considering that global awareness for sustainable development has risen to face environmental damages, different building materials have been considered from a mechanical perspective. In this sense, considering the richness of South America regarding its woods, the Guayacan and the Ecuadorian oak timbers have not been previously characterized. The present research has performed mechanical, thermal, and moisture content characterizations to acknowledge the benefits of considering these materials for the building industries. In this sense, Guayacan has been shown to have lower thermal conductivity, making it ideal for thermal insulation; the oak from Manabi showed the best compressive strength; while the oak from El Oro stands with the best tensile strength; and the oak from Loja showed the best modulus of elasticity. On the other hand, all the materials were compared by multicriteria decision methods to select the best, by using the COPRAS method driven by the objective entropy-weighted method, showing that the oak from Loja is the best choice considering the advantage that presents with the modulus of elasticity. In this sense, it is concluded that regarding the mechanical properties, there is not much difference for the compression, bending, and tensile strength; nevertheless, for the modulus of elasticity the oak from Loja stands out, making it a factor to be considered in the selection of a wood for building applications that is corroborated through multicriteria decision methods.

RESUMO

Processes of water retention and movement and the hydraulic conductivity are altered in the rhizosphere. The aim of this study was to investigate the physical-hydric properties of soil aggregates in the rhizosphere of annual ryegrass (Lolium multiflorum) cropped in a Kandiudalfic Eutrudox, taking into account aspects related to soil aggregate stability. Soil aggregates from rhizosphere soil (RZS) and soil between plant rows (SBP) were used to determine soil water retention curves (SWRCs) and saturated hydraulic conductivity (Ksat). In addition, properties related to soil aggregate stability, such as water-dispersible clay, soil organic carbon (SOC), and microbial activity, were also assessed. The higher microbial activity observed in the RZS was facilitated by increased SOC and microbial activity, resulting in improved soil aggregation (less water-dispersible clay). For nearly all measured matric potentials, RZS had a higher water content than SBP. This was attributed to the stability of aggregates, increase in SOC content, and the root exudates, which improved soil water retention. The increase in total porosity in RZS was associated with improved soil aggregation, which prevents deterioration of the soil pore space and results in higher Ksat and hydraulic conductivity as a function of the effective relative saturation in RZS compared to SBP.

RESUMO

Escalating global surface temperatures are highlighting the urgent need for energy-saving solutions. Phase-change materials (PCMs) have emerged as a promising avenue for enhancing thermal comfort in the construction sector. This study assessed the impact of incorporating PCMs ranging from 1% to 10% by mass into composite Portland cement partially replaced by fly ash (FA) and nanosilica particles (NS). Mechanical and electrochemical techniques were utilized to evaluate composite cements. The results indicate that the presence of PCMs delayed cement hydration, acting as a filler without chemically interacting within the composite. The combination of FA and PCMs reduced compressive strength at early ages, while thermal conductivity decreased after 90 days due to the melting point and the latent heat of PCMs. Samples with FA and NS showed a significant reduction in the CO2 penetration, attributed to their pozzolanic and microfiller effects, as well as reduced water absorption due to the non-absorptive nature of PCMs. Nitrogen physisorption confirmed structural changes in the cement matrix. Additionally, electrical resistivity and thermal behavior assessments revealed that PCM-containing samples could reduce temperatures by an average of 4 °C. This suggested that PCMs could be a viable alternative for materials with thermal insulation capacity, thereby contributing to energy efficiency in the construction sector.

RESUMO

Vulnerability curves (VCs) have been measured extensively to describe the differences in plant vulnerability to cavitation. Although the roles of hydraulic conductivity (Ks,max) and hydraulic safety (P50, embolism resistance), both of which are parameters of VCs ('sigmoidal' type), in tree demography have been evaluated across different forests, the direct linkages between VCs and tree demography are rarely explored. In this study, we combined measured VCs and plot data of 16 tree species in Panamanian seasonal tropical forests to investigate the connections between VCs and tree mortality, recruitment and growth. We found that the mortality and recruitment rates of evergreen species were most significantly positively correlated with P50. However, the mortality and recruitment rates of deciduous species only exhibited significant positive correlations with parameter a, which describes the steepness of VCs and indicates the sensitivity of conductivity loss with water potential decline, but is often neglected. These differences among evergreen and deciduous species may contribute to the poor performance of existing quantitative relationships (such as the fitting relationships for all 16 species) in capturing tree mortality and recruitment dynamics. Additionally, evergreen species presented a significant positive relationship between relative growth rate (RGR) and Ks,max, while deciduous species did not display such relationship. The RGR of both evergreen and deciduous species also displayed no significant correlations with P50 and a. Further analysis demonstrated that species with steeper VCs tended to have high mortality and recruitment rates, while species with flatter VCs were usually those with low mortality and recruitment rates. Our results highlight the important role of parameter a in tree demography, especially for deciduous species. Given that VC is a key component of plant hydraulic models, integrating measured VC rather than optimizing its parameters will help improve the ability to simulate and predict forest response to water availability.

Assuntos

RESUMO

Silver iodide is a prototype compound of superionic conductors that allows ions to flow through its structure. It exhibits a first-order phase transition at 420 K, characterized by an abrupt change in its ionic conductivity behavior, and above this temperature, its ionic conductivity increases by more than three orders of magnitude. Introducing small concentrations of carbon into the silver iodide structure produces a new material with a mixed conductivity (ionic and electronic) that increases with increasing temperature. In this work, we report the experimental results of the ionic conductivity as a function of the reciprocal temperature for the (AgI)x - C(1-x) mixture at low carbon concentrations (x = 0.99, 0.98, and 0.97). The ionic conductivity behavior as a function of reciprocal temperature was well fitted using a phenomenological model based on a random variable theory with a probability distribution function for the carriers. The experimental data show a proximity effect between the C and AgI phases. As a consequence of this proximity behavior, carbon concentration or temperature can control the conductivity of the (AgI)x - C(1-x) mixture.

RESUMO

The adsorption of oxygen and its reaction with target gases are the basis of the gas detection mechanism by using metal oxides. Here, we present a theoretical analysis of the sensor response, within the ionosorption model, for an n-type polycrystalline semiconductor. Our goal of our work is to reveal the mechanisms of gas sensing from a fundamental point of view. We revisit the existing models in which the sensor response presents a power-law behavior with a reducing gas partial pressure. Then, we show, based on the Wolkenstein theory of chemisorption, that the sensor response depends not only on the reducing gas partial pressure but also on the oxygen partial pressure. We also find that the obtained sensor response does not explicitly depend on the grain size, and if it does, it is exclusively through the rate constants related to the involved reactions.

Assuntos

RESUMO

New composites produced with recycled waste are needed to manufacture more sustainable construction materials. This paper aimed to analyze the hygrothermal and mechanical performance of plasterboard with a polymethylhydrosiloxane (PMHS) content, incorporating recycled PET microplastic waste and varying factors such as PMHS dose, homogenization time, and drying temperature after setting. A cube-centered experimental design matrix was performed. The crystal morphology, porosity, fluidity, water absorption, flexural strength, and thermal conductivity of plasterboards were measured. The results showed that incorporating recycled PET microplastics does not produce a significant difference in the absorption and flexural strength of plasterboards. However, the addition of recycled PET reduced the thermal conductivity of plasterboards by around 10%.

RESUMO

This work reports the dielectric behavior of the biopolymer ethyl cellulose (EC) observed from transient currents experiments under the action of a direct current (DC) electric field (~107 V/m) under vacuum conditions. The viscoelastic response of the EC was evaluated using dynamic mechanical analysis (DMA), observing a mechanical relaxation related to glass transition of around ~402 K. Furthermore, we propose a mathematical framework that describes the transient current in EC using a fractional differential equation, whose solution involves the Mittag-Leffler function. The fractional order, between 0 and 1, is related to the energy dissipation rate and the molecular mobility of the polymer. Subsequently, the conduction mechanisms are considered, on the one hand, the phenomena that occur through the polymer-electrode interface and, on the other hand, those which manifest themselves in the bulk material. Finally, alternating current (AC) conductivity measurements above the glass transition temperature (~402 K) and in a frequency domain from 20 Hz to 2 MHz were carried out, observing electrical conduction described by the segmental movements of the polymeric chains. Its electrical properties also position EC as a potential candidate for electrical, electronics, and mechatronics applications.

RESUMO

Eumelanin is a natural pigment that can be particularly valuable for sustainable bioelectronic devices due to its inherent biocompatibility and hydration-dependent conductivity. However, the low conductivity of eumelanin limits its technological development. In this research, electrochemical doping was proposed as an alternative route to increase the electronic conductivity of synthetic eumelanin derivatives. Thin films of sulfonated eumelanin were deposited on platinum interdigitated electrodes and electrochemically treated by using cyclic voltammetry and chronoamperometry treatments. X-ray photoelectron spectroscopy analysis confirmed ion doping in sulfonated melanin. Current-voltage, current-time, and electrochemical impedance measurements were used to investigate the effect of different aqueous electrolytes (including KCl and LiClO4) treatments on the charge transport of sulfonated eumelanin. We show that the conductivity depends on the type and size of the anion used and can reach 10-3 S·cm-1. Additionally, depending on the electrolyte, there is a change in charge transport from mixed ionic/electronic to a predominantly electronic-only conduction. Our results show that the chemical nature of the ion plays an important role in the electrochemical doping and, consequently, in the charge transport of eumelanin. These insights serve as inspiration to explore the use of alternative electrolytes with different compositions further and develop eumelanin-based devices with tunable conductivities.

Assuntos

RESUMO

One crucial property of concrete, particularly in construction, is its thermal conductivity, which impacts heat transfer through conduction. For example, reducing the thermal conductivity of concrete can lead to energy savings in buildings. Various techniques exist for measuring the thermal conductivity of materials, but there is limited discussion in the literature about suitable methods for concrete. In this study, the transient line source method is employed to evaluate the thermal conductivity of concrete samples with natural and synthetic fibers after 7 and 28 days of curing. The results indicate that concrete with hemp fiber generally exhibits higher thermal conductivity values, increasing by 48% after 28 days of curing, while synthetic fibers have a minimal effect. In conclusion, this research opens the door to using natural alternatives like hemp fiber to improve concrete's thermal properties, providing alternatives for thermo-active foundations and geothermal energy piles which require high thermal conductivities.

RESUMO

In Colombia there are estimated to be over 121,000 missing people and victims of forced disappearances. Forensic investigators therefore need assistance in determining optimal detection techniques for buried victims, to give victims' families closure and for the wider community to see that justice is being served. Previous research has created 12 controlled simulated clandestine graves of typical Colombian murder victim scenarios at 0.5 m - 1.2 m depths in savannah and rainforest sites in Colombia. The 0-3 years of geophysical monitoring results of were published, with this paper reporting on 4-8 years monitoring of both UAV drone results and geophysical data. The UAV results from the year 8 survey, published for first time from Colombia, showed that the simulated graves could still be located using NDVI and NIR multi-spectral data, but not using optical or other multi-spectral data. The 0-3 years of geophysical data found the simulated clandestine graves could be detected with electrical resistivity and GPR methods, with the 4-8 year surveys evidencing that they could still be detected using bulk ground conductivity surveys, GPR horizontal time slice datasets and 2D ERT profiles. Research implications suggest initial use of UAV remote sensing technology to pinpoint likely search areas, before subsequent ground reconnaissance, geophysical surveys and their interpretation, before intrusive investigation methods are employed for detecting missing and disappeared persons in Colombia.

Assuntos

RESUMO

Recent progress in synthesizing and integrating surface-supported metal-organic frameworks (SURMOFs) has highlighted their potential in developing hybrid electronic devices with exceptional mechanical flexibility, film processability, and cost-effectiveness. However, the low electrical conductivity of SURMOFs has limited their use in devices. To address this, researchers have utilized the porosity of SURMOFs to enhance electrical conductivity by incorporating conductive materials. This study introduces a method to improve the electrical conductivity of HKUST-1 templates by in situ polymerization of conductive polypyrrole (PPy) chains within the SURMOF pores (named as PPy@HKUST-1). Nanomembrane-origami technology is employed for integration, allowing a rolled-up metallic nanomembrane to contact the HKUST-1 films without causing damage. After a 24 h loading period, the electrical conductivity at room temperature reaches approximately 5.10-6 S m-1 . The nanomembrane-based contact enables reliable electrical characterization even at low temperatures. Key parameters of PPy@HKUST-1 films, such as trap barrier height, dielectric constant, and tunneling barrier height, are determined using established conduction mechanisms. These findings represent a significant advancement in real-time control of SURMOF conductivity, opening pathways for innovative electronic-optoelectronic device development. This study demonstrates the potential of SURMOFs to revolutionize hybrid electronic devices by enhancing electrical conductivity through intelligent integration strategies.

RESUMO

Escherichia coli bacterium is a rod-shaped organism composed of a complex double membrane structure. Knowledge of electric field driven ion transport through both membranes and the evolution of their induced permeabilization has important applications in biomedical engineering, delivery of genes and antibacterial agents. However, few studies have been conducted on Gram-negative bacteria in this regard considering the contribution of all ion types. To address this gap in knowledge, we have developed a deterministic and stochastic Brownian dynamics model to simulate in 3D space the motion of ions through pores formed in the plasma membranes of E. coli cells during electroporation. The diffusion coefficient, mobility, and translation time of Ca2+, Mg2+, Na+, K+, and Cl- ions within the pore region are estimated from the numerical model. Calculations of pore's conductance have been validated with experiments conducted at Gustave Roussy. From the simulations, it was found that the main driving force of ionic uptake during the pulse is the one due to the externally applied electric field. The results from this work provide a better understanding of ion transport during electroporation, aiding in the design of electrical pulses for maximizing ion throughput, primarily for application in cancer treatment.

Assuntos

RESUMO

This work presents the structural and electrical characterization of K2NiF4-type layered perovskites of LaSrAl1-xMgxO4-δ composition to be used as oxide-ion electrolytes for a solid-oxide fuel cell (SOFC). These perovskites were prepared by mechano-chemical synthesis (ball milling), an alternative to traditional synthesis methods such as citrate-nitrates and solid-state reaction. With these methods, two things are avoided: first, the use of nitrate salts, which are more environmentally harmful than oxide precursors, and second, it saves the series of long thermal treatments associated with solid-state reactions. After grinding the precursors, nanometric particles were obtained with a combination of crystalline regions and amorphous regions; this effect was determined by XRD and TEM, showing that Mg has a positive effect on the phase formation by only mechanical synthesis. R2C4: After sintering, it was found by XRD that the sample x = 0.1 only presents the diffraction peaks corresponding to the desired phase, which shows a phase purity greater than 97%, even higher than that of the standard undoped sample. For x = 0.2 and 0.3, there was a segregation of impurities, possibly by the local migration of La and Sr heavy cations; this was determined by SEM and EDS. The electrical characterization of the sintered pellets was carried out by electrochemical impedance spectroscopy, which determined that the incorporation of Mg in the structure improves the ionic conductivity by three orders of magnitude, obtaining conductivities of 1.6 mS/cm at 900 °C for x = 0.2. Although the improvement in conductivity is considerable, many challenges such as densification, the segregation of impurities, and the study of mechanical and thermal properties must be carried out on these materials to endorse them as solid electrolytes in SOFC.

RESUMO

Few studies have been conducted in the cooling systems of power plants; they have focused on Naegleria fowleri, leaving a gap in the knowledge of other pathogenic free-living amoebae in this environment. The objective of this study was to determine the occurrence of saline-tolerant pathogenic Acanthamoeba in a geothermal power plant. The identification of isolated amoebae at genus level was carried out, observing their morphological characteristics; the determination of genotype and species of Acanthamoeba was performed via molecular biology (PCR). Water temperature ranged from 18 to 43 °C and conductivity from 4.0 × 104 to 8.7 × 104 µS/cm; this last value was greater than the seawater value. Only five amoeba genera were found. Acanthamoeba was in all the sampling sites, showing high saline tolerance. The high temperature, but mainly high conductivity, were the environmental conditions that determined the presence of pathogenic free-living amoebae in the hot water. All the strains of Acanthamoeba culbertsoni killed the mice, having a mortality of 40 to 100%. Acanthamoeba genotypes T10 and T5 were identified, T10 is rarely isolated from the environment, while T5 is more frequent. This is the first time that genotypes T5 and T10 have been reported in the environment in Mexico.

RESUMO

Liposomes are prominent nanosystems for drug delivery, with potential extending beyond isolated drugs. Ethanol-aqueous plant extracts can be encapsulated within liposomes to protect bioactive compounds (secondary metabolites) from rapid oxidation and enable sustained release. Determining which compound classes are present in each extract and the encapsulation efficiency (EE) of these extracts in liposomes is crucial for nanocarrier functionality. This involves assessing the ratio of bioactive substances within liposomes to the total content. However, quantifying EE for non-isolated compounds poses challenges due to the need for advanced analytical equipment and biosensing approaches. This study introduces an innovative method for EE quantification, using a conductivity electrode (k = 0.842/cm) to establish an EE biosensing technology. By correlating dynamic light scattering (DLS), zeta potential (ZP), and electrical conductivity (Cnd) data with the conductivity meter's calibration curve, a robust relationship between the free extract concentration and Cnd (r2 ≥ 0.950) was established. Lavender-loaded liposomes demonstrated an EE of 56.33%, while wormwood and oregano formulations exhibited high EEs of 94.33% and 91.70%, respectively. In contrast, sage-loaded liposomes exhibited an inadequate EE, encapsulating only approximately 0.57% of the extract. The straightforward quantification of the free extract within liposome formulations, compared to more complex approaches, could facilitate EE determination and support future characterizations.

Assuntos

RESUMO

Herein, we report the synthesis, structural and microstructural characterization, and thermoelectric properties of AgSnm[Sb0.8Bi0.2]Te2+m and Br-doped telluride systems. These compounds were prepared by solid-state reaction at high temperature. Powder X-ray diffraction data reveal that these samples exhibit crystal structures related to the NaCl-type lattice. The microstructures and morphologies are investigated by scanning electron microscopy, energy-dispersive X-ray spectroscopy (EDS), and high-resolution transmission electron microscopy (HRTEM). Positive values of the Seebeck coefficient (S) indicate that the transport properties are dominated by holes. The S of undoped AgSnm[Sb0.8Bi0.2]Te2+m ranges from +40 to 57 µV·K-1. Br-doped samples with m = 2 show S values of +74 µV·K-1 at RT, and the Seebeck coefficient increases almost linearly with increasing temperature. The total thermal conductivity (κtot) monotonically increases with increasing temperature (10-300 K). The κtot values of undoped AgSnm[Sb0.8Bi0.2]Te2+m are ~1.8 W m-1 K-1 (m = 4) and ~1.0 W m-1 K-1 (m = 2) at 300 K. The electrical conductivity (σ) decreases almost linearly with increasing temperature, indicating metal-like behavior. The ZT value increases as a function of temperature. A maximum ZT value of ~0.07 is achieved at room temperature for the Br-doped phase with m = 4.

RESUMO

BACKGROUND: Packed cell volume (PCV) is important for assessing a patient's health status. Some blood gas analyzers measure hematocrit, and the agreement with PCV varies among different analyzers. OBJECTIVES: We aimed to determine the agreement between PCV measured by microcentrifugation and hematocrit measured by the Cobas b121 blood gas analyzer in dogs, cats, and horses. METHODS: Whole blood samples for PCV and blood gas analysis were collected in lithium-heparin syringes and analyzed within 10 min of collection. Agreement and association between the PCV and Cobas b121 generated hematocrit were assessed by the Bland-Altman method, Pearson's correlation, Deming regression analysis, and paired t tests. A total allowable error of 10% was used for the analysis. RESULTS: This study included 45 dogs, 45 cats, and 33 horses. The respective mean ± SD (minimum-maximum) of PCVs and hematocrits were: dogs, 34.9 ± 9.9% (9.0-55.0) and 32.5 ± 8.8% (10.4-50.6); cats, 29.0 ± 9.6% (11.0-51.0) and 26.9 ± 9.3% (10.2-50.9); horses, 34.2 ± 6.5% (24.0-47.0) and 34.1 ± 6.0% (22.5-46.1). There were no significant differences between the methods. The bias ± SD was: dogs, -2.4 ± 2.6%; cats, -2.2 ± 2.3%; horses, -0.1 ± 2.4%. Pearson's correlation coefficients were > 0.90 for all species (P < 0.0001). In 60%, 49%, and 85% of the samples for dogs, cats, and horses, respectively, the percentage differences between the methods were within 10%. CONCLUSIONS: The Cobas b121 blood gas analyzer provided accurate estimates of PCVs in horses. However, in dogs and cats, there was a large frequency of unacceptable differences between the methods.

Assuntos

RESUMO

Plasterboard is an important building material in the construction industry because it allows for quick installation of walls, partitions, and ceilings. Although a common material, knowledge about its performance related to modern polymers and fabrication conditions is still lacking. The present work analyzes how some manufacturing factors applied during the plaster board fabrication impact on some plasterboard properties, including water absorption, flexural strength, and thermal conductivity. The manufacturing variables evaluated are the dose (D) of polymethylhydrosiloxane (PMHS), the agitation time of the mixture (H), and the drying temperature of the plaster boards after setting (T). The results suggest that factors D, H, and T induce changes in the porosity and the morphological structure of the calcium sulfate dihydrate crystals formed. Performance is evaluated at two levels of each factor following a statistical method of factorial experimental design centered on a cube. Morphological changes in the crystals of the resulting boards were evaluated with scanning electron microscopy (SEM) and the IMAGEJ image analysis program. Porosity changes were evaluated with X-ray microcomputed tomography (XMT) and 3D image analysis tools. The length-to-width ratio of the crystals decreases as it goes from low PMHS dosage to high dosage, favoring a better compaction of the plasterboard under the right stirring time and drying temperature. In contrast, the porosity generated by the incorporation of PMHS increases when going from low-level to high-level conditions and affects the maximum size of the pores being generated, with a maximum value achieved at 0.6% dosage, 40 s, and 140 °C conditions. The presence of an optimal PMHS dosage value that is approximately 0.6-1.0% is evidenced. In fact, when comparing trails without and with PMHS addition, a 10% decrease in thermal conductivity is achieved at high H (60 s) and high T (150 °C) level conditions. Water absorption decreases by more than 90% when PMHS is added, mainly due to the hydrophobic action of the PMHS. Minimum water absorption levels can be obtained at high drying temperatures. Finally, the resistance to flexion is not affected by the addition of PMHS because apparently there are two opposing forces acting: on one hand is the decrease in the length-width ratio giving more compactness, and on the other hand is the generation of pores. The maximum resistance to flexion was found around a dosage of 0.6% PMHS. In conclusion, the results suggest that the addition of PMHS, the correct agitation time of the mixture, and the drying temperature reduce the water absorption and the thermal conductivity of the gypsum boards, with no significant changes in the flexural resistance.

RESUMO

Creosote is an organic pollutant formed by a complex mixture of highly toxic and carcinogenic compounds and classified as a dense non-aqueous phase liquid (DNAPL). Its migration depends on media and fluid properties that control the multiphase flow in the subsurface. Residual saturation and hydraulic conductivity are essential parameters to accurately simulate fluid displacement in porous media. This work shows the behavior of creosote in porous medium for sandy and clay soils, collected in a contaminated area in the state of São Paulo, Brazil. Creosote retention was evaluated and compared to water. The retention curve parameters were obtained based on van Genuchten and Brooks and Corey models. The hydraulic conductivities of creosote and water are presented for both soils. The results show that, in the clay soil, water was more retained than creosote, while in the sandy soil, creosote retention was higher. The hydraulic conductivity values obtained in the clay soil show a difference of two orders of magnitude between creosote and water. Although creosote is a viscous fluid, it presents considerable mobility in the clay soil, which is relevant in remediation processes. This study advances our knowledge about DNAPL behavior in clay and sand, and no other study of creosote parameters in these porous media was found. A more accurate estimate of the time required for a liquid spill to reach groundwater can then be predicted, so that appropriate actions can be taken and risk management can be carried out.

Assuntos