RESUMO
A laser-induced graphene (LIG) surface modified with Prussian blue (iron hexacyanoferrate) is demonstrated as a novel electrochemical sensing platform for the sensitive and selective detection of hydrogen peroxide. Electrochemical Prussian blue (PB) modification on porous graphene films engraved by infrared laser over flexible polyimide was accomplished. Scanning electron microscopy images combined with Raman spectra confirm the formation of porous graphene and homogenous electrodeposition of PB over this porous surface. Electrochemical impedance spectroscopy reveals a substantial decrease in the resistance to charge transfer values (from 395 to 31.4 Ω) after the PB insertion, which confirms the formation of a highly conductive PB-graphene composite. The synergistic properties of PB and porous graphene were investigated for the constant monitoring of hydrogen peroxide at 0.0 V vs. Ag|AgCl|KCl(sat.), under high-flow injections (166 µL s-1) confirming the high stability of the modified surface and fast response within a wide linear range (from 1 to 200 µmol L-1). Satisfactory detection limit (0.26 µmol L-1) and selectivity verified by the analysis of complex samples confirmed the excellent sensing performance of this platform. We highlight that the outstanding sensing characteristics of the developed sensor were superior in comparison with other PB-based or LIG-based electrochemical sensors reported for hydrogen peroxide detection.
Assuntos
Grafite , Técnicas Eletroquímicas/métodos , Eletrodos , Ferrocianetos , Grafite/química , Peróxido de Hidrogênio/análise , LasersRESUMO
The fabrication of PDMS microfluidic structures through soft lithography is widely reported. While this well-established method gives high precision microstructures and has been successfully used for many researchers, it often requires sophisticated instrumentation and expensive materials such as clean room facilities and photoresists. Thus, we present here a simple protocol that allows the rapid molding of simple linear microchannels in PDMS substrates aiming microfluidics-based applications. It might serve as an alternative to researchers that do not have access to sophisticated facilities such as clean rooms. The method developed here consists on the use of pencil graphite leads as template for the molding of PDMS channels. It yields structures that can be used for several applications, such as housing support for electrochemical sensors or channels for flow devices. Here, the microdevices produced through this protocol were employed for the accommodation of carbon black paste, which was utilized for the first time as amperometric sensor in microchip electrophoresis. This platform was successfully used for the separation and detection of model analytes. Ascorbic acid and iodide were separated within 45 s with peak resolution of 1.2 and sensitivities of 198 and 492 pA/µM, respectively. The background noise was ca. 84 pA. The analytical usefulness of the system developed was successfully tested through the quantification of iodide in commercial pharmaceutical formulations. It demonstrates good efficiency of the microfabrication protocol developed and enables its use for the easy and rapid prototyping of PDMS structures over a low fabrication cost.
Assuntos
Microfluídica/instrumentação , Dimetilpolisiloxanos , Eletroforese em Microchip/instrumentação , Eletroforese em Microchip/métodos , Desenho de Equipamento , Grafite , Microfluídica/economiaRESUMO
Microchip electrophoresis is a versatile separation technique. Electrochemical detection is suitable to apply to microdevices due to its easy integration to the fabrication process and good sensitivity and selectivity. Here we describe the procedures to prepare Pt band electrodes deposited on glass to couple to polydimethylsiloxane (PDMS) microchips aiming the separation and detection of nitrite using an isolated potentiostat.
Assuntos
Dimetilpolisiloxanos/química , Eletroforese em Microchip/instrumentação , Nitritos/análise , Técnicas Biossensoriais/instrumentação , Eletrodos , Eletroforese em Microchip/métodos , VidroRESUMO
Pathogenic bacteria are responsible for several diseases in humans and in a variety of hosts. Detection of pathogenic bacteria is imperative to avoid and/or fight their potential harmful effects. This work reports on the first amperometric biosensor for the rapid detection of Streptococcus agalactiae (S. agalactiae). The biosensor relies on a single biotinylated antibody that immobilizes the bacteria on a screen-printed carbon electrode while is further linked to a streptavidin-conjugated HRP reporter. The biotinylated antibody provides selectivity to the biosensor whereas serves as an anchoring point to the reporter for further amplification of the electrochemical signal. The resultant immunosensor is simple, responds rapidly, and allows for the selective and highly sensitive quantification of S. agalactiae cells in a concentration range of 101-107CFUml-1, with a detection limit of 10CFUml-1. The approach not only enables a rapid detection and quantification of S. agalactiae in environmental samples but also opens up new opportunities for the simple fabrication of electrochemical immunosensors for different target pathogens.
Assuntos
Anticorpos Imobilizados/química , Técnicas Biossensoriais/métodos , Doenças dos Peixes/diagnóstico , Infecções Estreptocócicas/veterinária , Streptococcus agalactiae/isolamento & purificação , Tilápia/microbiologia , Microbiologia da Água , Animais , Técnicas Biossensoriais/economia , Técnicas Eletroquímicas/economia , Técnicas Eletroquímicas/métodos , Eletrodos , Doenças dos Peixes/microbiologia , Imunoensaio/economia , Imunoensaio/métodos , Limite de Detecção , Infecções Estreptocócicas/diagnóstico , Infecções Estreptocócicas/microbiologiaRESUMO
In this work, the possibility of simultaneous determination of three compounds with a single-injection step using batch injection analysis with multiple pulse amperometric detection (BIA-MPA) is demonstrated for the first time. A sequence of three potential pulses (+1.25 V, +1.60 V, and +1.80 V) was applied with the acquisition of three separate amperograms. 8-Chlorotheophylline was detected selectively at +1.25 V, both 8-chlorotheophylline and pyridoxine at +1.60V and 8-chlorotheophylline, pyridoxine, and diphenhydramine at +1.80 V. Subtraction between the currents detected at the three amperograms (with the help of correction factors) was used for the selective determination of pyridoxine and diphenhydramine. The proposed method is simple, inexpensive, fast (60 injections h(-1)), and present selectivity for the determination of the three compounds in pharmaceutical samples, with results similar to those obtained by HPLC (95% confidence level).
Assuntos
Eletroquímica/métodos , Injeções/métodos , Difenidramina/análise , Eletroquímica/economia , Concentração de Íons de Hidrogênio , Teofilina/análogos & derivados , Teofilina/análise , Fatores de TempoRESUMO
Poly [Ni-Protoporphyrin] film (pNiPP), containing multiwall carbon nanotubes (MWCNT) was used to cover a glassy carbon electrode. The hybrid material (pNiPP/MWCNT) successfully combines the permselectivity of pNiPP with the high conductivity of MWCNT. The modified electrode was used to perform amperometric detection of long chain aliphatic amines (LCAA) in order to prevent the passivation effect of the aliphatic chain. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) demonstrated that the pNiPP/MWCNT facilitates the electron transfer reaction. The charge transfer resistance (Rct) values were significantly lower by up to one order of magnitude compared to the bare electrode. Differential pulse polarography (DPP) showed a marked decrease of the overpotential generated by the aliphatic chain. The calibration of the amperometric peak area vs. concentrations of derivatized LCAA exhibits a linear response within the range of 0.018 and 28 µM and correlation coefficient (R(2)) higher than 0.999 (n=5). The quantitation limit of the pNiPP/MWCNT electrode is about 400 times lower than the UV-visible detection. RSD of 7.2%, 5.8%, 2.5% and 2.3% was obtained for concentrations of 0.028, 0.28, 2.8 and 28 µM of ferrocenyl octadecylamine. A solution of sphingosine, 0.23 µM, was exclusively detected with HPLC-ECD with pNiPP/MWCNT electrode.
Assuntos
Aminas/análise , Metaloporfirinas/química , Nanocompostos/química , Nanotubos de Carbono/química , Níquel/química , Protoporfirinas/química , Aminas/química , Condutividade Elétrica , EletroquímicaRESUMO
An HPLC-PAD method using a gold working electrode and a triple-potential waveform was developed for the simultaneous determination of streptomycin and dihydrostreptomycin in veterinary drugs. Glucose was used as the internal standard, and the triple-potential waveform was optimized using a factorial and a central composite design. The optimum potentials were as follows: amperometric detection, E1=-0.15V; cleaning potential, E2=+0.85V; and reactivation of the electrode surface, E3=-0.65V. For the separation of the aminoglycosides and the internal standard of glucose, a CarboPac™ PA1 anion exchange column was used together with a mobile phase consisting of a 0.070 mol L(-1) sodium hydroxide solution in the isocratic elution mode with a flow rate of 0.8 mL min(-1). The method was validated and applied to the determination of streptomycin and dihydrostreptomycin in veterinary formulations (injection, suspension and ointment) without any previous sample pretreatment, except for the ointments, for which a liquid-liquid extraction was required before HPLC-PAD analysis. The method showed adequate selectivity, with an accuracy of 98-107% and a precision of less than 3.9%.