RESUMO
Estimation of scaling-up parameters for a site restoration process using a surfactant-enhanced soil washing (SESW) process followed by the application of advanced oxidation processes (Fenton and photo-Fenton) was performed. For the SESW, different parameters were varied and the soil washing efficiency for pesticide (2,4-D) removal assessed. The resulting wastewater was treated using the Fenton reaction in the absence and presence of ultraviolet (UV) radiation for pesticide removal. Results showed that agitation speed of 1550 rpm was preferable for the best pesticide removal from contaminated soil. It was possible to wash contaminated soils with different soil concentrations; however the power drawn was higher as the soil concentration increased. Complete removal of the pesticide and the remaining surfactant was achieved using different reaction conditions. The best degradation conditions were for the photo-Fenton process using [Fe(II)] = 0.3 mM; [H2O2] = 4.0 mM where complete 2,4-D and sodium dodecylsulfate (SDS) removal was observed after 8 and 10 minutes of reaction, respectively. Further increase in the hydrogen peroxide or iron salt concentration did not show any improvement in the reaction rate. Kinetic parameters, i.e. reaction rate constant and scaling-up parameters, were determined. It was shown that, by coupling both processes (SESW and AOPs), it is possible the restoration of contaminated sites.
Assuntos
Recuperação e Remediação Ambiental/métodos , Peróxido de Hidrogênio/química , Ferro/química , Poluentes do Solo/química , Tensoativos/química , Ácido 2,4-Diclorofenoxiacético/química , Eliminação de Resíduos Líquidos/métodos , Águas Residuárias/químicaRESUMO
This study was conducted to evaluate the ozone, UV and O3/UV processes for the reuse of sewage treatment plant effluent (Universidad Autonoma Metropolitana Azcapotzalco wastewater treatment plant). The ozone/UV process was compared to individual ozone and the UV processes and control parameters were total and fecal coliforms. Different ozone concentrations (6-12 mg O3/min) and different UV fluencies (6.7-20.12 mJ/cm²) were tested. It is possible to conclude than none of the processes achieved the disinfection levels required to comply with the Mexican standard NOM-003-SEMARNAT-1997. The continuous ozone process offered the lower total and fecal coliforms reductions, while UV light resulted a disinfection agent with higher germicide power than ozone. The maximum logarithmic reduction achieved due to the combined ozone/UV process was of 2.04 for fecal coliforms and of 2.17 for total coliforms. The next 8 combinations showed lower removal efficiencies, but always higher than those obtained with the single ozone or UV processes. The ozone/UV process was highly effective for the disinfection and a synergistic effect was observed.
Assuntos
Ozônio , Raios Ultravioleta , Eliminação de Resíduos Líquidos/métodos , Purificação da Água/métodosRESUMO
The use of iron in a +6 valence state, (Fe (VI), as FeO4(-2)) was tested as a novel alternative for wastewater disinfection and decontamination. The removal of organic matter (OM) and index microorganisms present in an effluent of a wastewater plant was determined using FeO4(-2) without any pH adjustment. It was observed that concentrations of FeO4(-2) ranging between 5 and 14 mg l(-1) inactivated up to 4-log of the index microorganisms (initial concentration c.a. 10(6) CFU/100 ml) and achieved OM removal up to almost 50%. The performance of FeO4(-2) was compared with OM oxidation and disinfection using hypochlorite. It was observed that hypochlorite was less effective in OM oxidation and coliform inactivation than ferrate. Results of this work suggest that FeO4(-2) could be an interesting oxidant able to deactivate pathogenic microorganisms in water with high OM content and readily oxidize organic matter without jeopardizing its efficiency on microorganism inactivation.
Assuntos
Ferro/química , Eliminação de Resíduos Líquidos/métodos , Purificação da Água/métodos , Enterobacteriaceae , Humanos , Concentração de Íons de Hidrogênio , Nefelometria e Turbidimetria , OxirreduçãoRESUMO
Wastewater produced in the contaminated soil washing was treated by means of coagulation-flocculation (CF) process. The wastewater contained petroleum hydrocarbons, a surfactant, i.e., sodium dodecyl sulfate (SDS) as well as salts, brownish organic matter and other constituents that were lixiviated from the soil during the washing process. The main goal of this work was to develop a process for treating the wastewaters generated when washing hydrocarbon-contaminated soils in such a way that it could be recycled to the washing process, and also be disposed at the end of the process properly. A second objective was to study the relationship among the coagulant and flocculant doses and the pH at which the CF process is developed, for systems where methylene blue active substances (MBAS) as well as oil and greases were present. The results for the selection of the right coagulant and flocculant type and dose, the optimum pH value for the CF process and the interactions among the three parameters are detailed along this work. The best coagulant and flocculant were FeCl(3) and Tecnifloc 998 at doses of 4,000 and 1 mg/L, correspondingly at pH of 5. These conditions gave color, turbidity, chemical oxygen demand (COD) and conductivity removals of 99.8, 99.6, 97.1 and 35%, respectively. It was concluded that it is feasible to treat the wastewaters generated in the contaminated soil washing process through CF process, and therefore, wastewaters could be recycled to the washing process or disposed to drainage.
Assuntos
Cloretos/química , Compostos Férricos/química , Hidrocarbonetos/análise , Dodecilsulfato de Sódio/análise , Poluentes do Solo/análise , Tensoativos/análise , Eliminação de Resíduos Líquidos/métodos , Purificação da Água/métodos , Condutividade Elétrica , Floculação , Concentração de Íons de Hidrogênio , México , Nefelometria e Turbidimetria , Oxigênio/análiseRESUMO
Decontamination of soil washing wastewater was performed using two different solar driven advanced oxidation processes (AOPs): the photo-Fenton reaction and the cobalt/peroxymonosulfate/ultraviolet (Co/PMS/UV) process. Complete sodium dodecyl sulphate (SDS), the surfactant agent used to enhance soil washing process, degradation was achieved when the Co/PMS/UV process was used. In the case of photo-Fenton reaction, almost complete SDS degradation was achieved after the use of almost four times the actual energy amount required by the Co/PMS/UV process. Initial reaction rate in the first 15min (IR15) was determined for each process in order to compare them. Highest IR15 value was determined for the Co/PMS/UV process (0.011mmol/min) followed by the photo-Fenton reaction (0.0072mmol/min) and the dark Co/PMS and Fenton processes (IR15=0.002mmol/min in both cases). Organic matter depletion in the wastewater, as the sum of surfactant and total petroleum hydrocarbons present (measured as chemical oxygen demand, COD), was also determined for both solar driven processes. It was found that, for the case of COD, the highest removal (69%) was achieved when photo-Fenton reaction was used whereas Co/PMS/UV process yielded a slightly lower removal (51%). In both cases, organic matter removal achieved was over 50%, which can be consider proper for the coupling of the tested AOPs with conventional wastewater treatment processes such as biodegradation.
Assuntos
Descontaminação/métodos , Poluentes do Solo/análise , Energia Solar , Eliminação de Resíduos Líquidos/métodos , Cobalto/química , Escuridão , Hidrocarbonetos/química , Indicadores e Reagentes , Oxirredução , Peróxidos/química , Dodecilsulfato de Sódio/química , Tensoativos/química , Raios UltravioletaRESUMO
Mexico has a very important oil industry, comprehending the exploration, production, transformation, storage and distribution of crude oil and its fractions. Petroleos Mexicanos (PEMEX) is a state-owned monopoly in charge of these activities. Oil and oil-products transport is an extremely crucial operation for the cycle production-transformation-distribution. Pipeline system transport crude oil and sub-products along the country (including liquids, gases and mixtures). It has been reported that more than 30% of the oil ducts in Mexico have been operating for over 30 years, although their lifetime has been calculated in 25-30 years. This work is aimed at characterizing a zone around six oil-pipeline pumping stations located at northern Mexico. The specific places to evaluate soil contamination were (1) the distribution head of the Gomez Palacio (GOPA) pumping station; (2) the north side of the old ditch, the API oil separator and the wastewater zones of the Jimenez (JIM) pumping station; (3) the pumping stations of Ceballos (CE), Peronal (PER), Simon Bolivar (SIBO), and Mayran (MAY). The study comprehended sampling of the areas, delimitation of contamination in the vertical and horizontal extension, analysis of the sampled soils, regarding TPH and, in some cases, the 16 PAHs considered as a priority by USEPA, calculation of areas and volumes contaminated (according to the Mexican legislation, specifically NOM-EM-138-ECOL-2002) and, finally, a proposal for the best remediation techniques suitable for the encountered contamination levels and the localization of contaminants. In general, TPHs were found in all the pumping stations analyzed in this study. Regarding maximal TPHs concentrations at the stations, their order of contamination was as follows: SIBO>CE>PER>MAY>JIM>GOPA. PAHs were found only in a few points at concentrations above the detection limit. At the Jimenez, Gomez Palacio, Peronal, and Ceballos stations, only one point, with PAHs values over the detection limit was found, whereas two points were found at Mayran, and finally at the Simon Bolivar station there were four points with measurable amounts of PAHs. Given the areas and volumes that need to be treated (32835 m3), as well as the physical position of contaminants, it is considered that excavation of the contaminated soil is feasible and the cleaning process could be soil washing assisted with surfactants, though bioremediation should not been discharged as a possible remediation technique.
Assuntos
Óleos Combustíveis/análise , Poluentes do Solo/análise , Solo/análise , Monitoramento Ambiental/métodos , Geografia , México , Hidrocarbonetos Policíclicos Aromáticos/análiseRESUMO
Oil spills due to oil pipelines is a very frequent problem in Mexico. Petroleos Mexicanos (PEMEX), very concerned with the environmental agenda, has been developing inspection and correction plans for zones around oil pipelines pumping stations and pipeline right-of-way. These stations are located at regular intervals of kilometres along the pipelines. In this study, two sections of an oil pipeline and two pipeline pumping stations zones are characterized in terms of the presence of Total Petroleum Hydrocarbons (TPHs) and Polycyclic Aromatic Hydrocarbons (PAHs). The study comprehends sampling of the areas, delimitation of contamination in the vertical and horizontal extension, analysis of the sampled soils regarding TPHs content and, in some cases, the 16 PAHs considered as priority by USEPA, calculation of areas and volumes contaminated (according to Mexican legislation, specifically NOM-EM-138-ECOL-2002) and, finally, a proposal for the best remediation techniques suitable for the contamination levels and the localization of contaminants.
Assuntos
Petróleo , Poluentes do Solo/análise , México , Compostos Policíclicos/análiseRESUMO
Degradation of two chlorinated pesticides (2,4-D and DDT) using a 54-mL glass column packed with tezontle (a low-cost basaltic scoria) was tested. Bacteria were cultured in YPG (yeast, peptone, and glucose) liquid medium at 32 degrees C. The rich medium was pumped during 24 h through the column to inoculate it. Later, the wasted medium was discharged and the pesticide added. Optical densities, TOC, and pesticide concentration were determined. Pesticide removals for 2,4-D (with initial concentration between 100 and 500 mg/L) were about 99%. DDT removal (at initial concentration of up to 150 mg/L) was as high as 55-99%. TOC removals for 2,4-D was in the 36-87% interval, whereas for DDT they were as high as 36-78%.
Assuntos
Ácido 2,4-Diclorofenoxiacético/metabolismo , DDT/metabolismo , Herbicidas/metabolismo , Praguicidas/metabolismo , Pseudomonas fluorescens/metabolismo , Ácido 2,4-Diclorofenoxiacético/análise , Biodegradação Ambiental , DDT/análise , Relação Dose-Resposta a Droga , Herbicidas/análise , Cinética , Praguicidas/análiseRESUMO
Many oil industry related sites have become contaminated due to the activities characteristic of this industry, such as oil exploration and production, refining, and petro-chemistry. In Mexico, reported hydrocarbon spills for the year 2000 amounted to 185203, equivalent to 6252 tons (PEMEX, 2000). The first step for the remediation of these polluted sites is to assess the size and intensity of the oil contamination affecting the subsoil and groundwater, followed by a health risk assessment to establish clean up levels. The aim of this work was to characterize the soil and water in a north-central Mexico Oil Storage and Distribution Station (ODSS), in terms of TPHs, gasoline and diesel fractions, BTEX, PAHs, MTBE, and some metals. Besides, measurements of the explosivity index along the ODSS were made and we describe and discuss the risk health assessment analysis performed at the ODSS, as well as the recommendations arising from it. Considering soils with TPH concentrations higher than 2000 mg kg(-1), the contaminated areas corresponding to the railway zone is about 12776.5 m2, to the south of the storage tanks is about 6558 m2, and to the south of the filling tanks is about 783 m2. Total area to be treated is about 20107 m2 (volume of 20107 m3), considering 1m depth.
Assuntos
Exposição Ambiental , Sedimentos Geológicos/análise , Petróleo/análise , Poluentes do Solo/análise , Poluentes Químicos da Água/análise , Óleos Combustíveis/análise , Gasolina/análise , Sedimentos Geológicos/química , Indústrias , Metais/análise , México , Medição de Risco , Poluentes do Solo/toxicidade , Poluentes Químicos da Água/toxicidadeRESUMO
The soil of a coastal Mexican refinery is quite contaminated, especially by hydrocarbons, with detected concentrations up to 130000 mg kg(-1) as TPHs (total petroleum hydrocarbons). The main sources of contamination are pipelines, valves, and old storage tanks, besides the land disposal of untreated hydrocarbon sediments derived from the cleaning of storage tanks. A health risk assessment (HRA) was carried out in order to measure the risk hazard indexes and clean-up standards for the refinery soil. HRA suggested the following actions to be taken: benzene concentrations must be reduced in eight of the 16 studied refinery zones to 0.0074-0.0078 mg kg(-1). Also, vanadium concentration must be reduced in two zones up to a concentration of 100 mg kg(-1). In only one of all of the studied zones, benzo(a)pyrene concentration must be reduced to 0.1 mg kg(-1). After 1 yr, TPHs showed a diminution of about 52%. Even though TPHs concentrations were variable, during 1999 the average concentrations were as much as 15.5 times the goal concentration. For year 2000, TPHs concentrations were only 7.4-fold the proposed value. For the 1999-2000 period, PAHs (polycyclic aromatic hydrocarbons) concentrations decreased by 82%. Some PAHs with 2, 3, 4, and 5 aromatic rings were removed up to 100% values.