RESUMO
The aims of this work were to evaluate the reactivity of sugarcane straw ashes (SCSA) burned under controlled conditions and to analyze their reactivity in blended cement and hydrated lime pastes by thermogravimetric analysis (TG) and calorimetry. Four different ashes were produced, and burned at 600 °C, 700 °C, 800 °C and 900 °C (SCSA600, SCSA700, SCSA800 and SCSA900, respectively). These ashes were characterized by X-ray fluorescence spectroscopy, X-ray diffractometry, particle size distribution by laser diffraction and specific area surfaces to assess their potential interest in the partial replacement of inorganic binders (Portland cement (OPC) and hydrated lime). The hydrated lime pastes were subjected to scanning electron microscopy (SEM) and TG. The blended cement pastes were analyzed by TG and calorimetry, compressive strength testing and mercury intrusion porosimetry. High lime fixation percentages were observed in the hydrated lime and OPC pastes and were higher than 75% and 50% for the ashes burned at 600 °C and 700 °C, respectively. Calorimetry showed a delay in the heat release of SCSA600 and SCSA700 compared to the control paste. These pastes also had higher compressive strength and a smaller total pore volume. The results indicate the positive response of preparing sugar cane ashes under controlled conditions (mainly for straw calcined within the 600-700 °C range) for their use as pozzolanic addition by partially replacing inorganic binders.
RESUMO
In this research work, the quantitative characterization of a binary blend comprised of two pozzolans (sugar cane straw (SCSA)-sugar cane bagasse ashes (SCBA), bamboo leaf ash (BLAsh)-SCBA and paper sludge (PS)-fly ash (FA)) taking into account the calculated values of the kinetic parameters of the reaction in the pozzolan/calcium hydroxide system is shown. The paper shows the most significant and important results obtained by the authors in the quantitative assessment (calculation of kinetic parameters) of the pozzolanic reaction of different mixtures of pozzolanic materials that are residues from agriculture or industrial processes. This allows a direct and rigorous comparison of the pozzolanic activity of the binary combinations of materials. The values of the kinetic parameters (reaction rate constant or activation free energy) constitute a very precise quantitative index of the pozzolanic activity of the binary combinations of materials, which is very useful for its employment in the elaboration of ternary cements. This paper shows that the binary blends 1SCBA60Blash40, 1SCBA50Blash50, 1SCBA70Blash30 have a very high pozzolanic reactivity followed by PSLSFA, 2SCBA50SCSA50, PSISFA and SCWI.
RESUMO
Densification processes are used to improve the mechanical and physical properties of lignocellulose materials by either collapsing the cell cavities or by filling up the pores, consequently reducing the void volume fraction. This paper focuses on an extensive review of bamboo densification process, which is achieved by compressing the material in the direction perpendicular to the fibers using mainly two different techniques: an open system, thermo-mechanical (TM), or a closed system, viscoelastic-thermal-compression (VTC). The main aim of bamboo densification is to decrease its heterogeneity, as well as to improve its mechanical and physical performance. In addition, densification may occur during the manufacturing of bamboo products in which hot-pressing processes are used to mold bamboo panels. There are over 1600 publications about bamboo, concentrated in the recent decade, mainly about engineered materials. Although several papers regarding bamboo and wood densification are available, very few studies have comprehensively investigated the densification process solely through compression of natural bamboo culms. According to the literature, applying a combination of compression of 6-12 MPa at temperatures between 120-170 °C for 8-20 min can produce materials with higher strength in comparison to the mechanical properties of natural bamboo. The majority of research on bamboo densification indicates that the modified material results in improved properties in terms of density, hardness, bending strength, stiffness, and durability. This paper provides a review that consolidates knowledge on the concept of bamboo culm densification, discusses the roles of parameters that control the process, ascertains the best practice, and finally determines gaps in this field of knowledge.
RESUMO
This study was conducted to determine the relationship among temperatures measured at different anatomical sites of the animal body and their daily pattern as indicative of the thermal stress in lactating dairy cows under tropical conditions. Environmental dry bulb (DBT) and black globe (BGT) temperatures and relative humidity (RH) were recorded. Rectal temperature (RT), respiratory frequency (RF), body surface (BST), internal base of tail (TT), vulva (VT) and auricular temperatures (AT) were collected, from 37 Black and White Holstein cows at 0700, 1300 and 1800 hours. RT showed a moderately and positive correlations with all body temperatures, ranging from 0.59 with TT to 0.64 with BST. Correlations among AT, VT and TT with RF were very similar (from 0.63 to 0.64) and were greater than those observed for RF with RT (0.55) or with BST (0.54). RF and RT were positively correlated to TT (0.63 and 0.59, respectively), AT (r = 0.63 for both) and VT (r = 0.64 and 0.63, respectively). Positive and very high correlations were observed among AT, VT and TT (from 0.94 to 0.97) indicating good association of temperatures measured in these anatomical sites. Correlations of BST with AT and VT were positive and very similar (0.71 and 0.72, respectively) and lower with TT (0.66). The AT, TT, VT and BST presented similar patterns and follow the variations of DBT through the day. Temperatures measured at different anatomical sites of the animal body have the potential to be used as indicative of the thermal stress in lactating dairy cows.