RESUMO

This research assessed the effects of pre-heating on the physical-mechanical-chemical properties of different resin composites. For this, resin composites were evaluated in 6 levels: Admira/ADM, Vitra/VIT, Filtek Supreme/FS, Filtek Supreme Flowable/FSF, Filtek One/FO, and Filtek Bulk Fill Flowable/FBF; temperature was evaluated in 4 levels using a composite heater: room temperature/22 ºC, 37 ºC, 54 ºC, and 68 ºC. Response variables were: degree of conversion/DC, flexural strength/FS and color stability/ΔE (immediately after light curing/LC, after 7 days of dark-dry-storage, and after 24 h and 3 days of artificial aging in water at 60 ºC). Data were subjected to 2-way ANOVA (DC and FR) and 3-way repeated measurements ANOVA (ΔE), all followed by Tukey's test (α = 5%). DC were similar (FBF, FS, and FSF) or increased (ADM, FO, and VIT) as the temperature increased. Results of FR were unchanged or increased for all composites except VIT and ADM. High-viscosity composites (VIT and FS) showed higher FR values than low-viscosity composite (FSF). For bulk-fill composites, FBF and FO showed similar results, but lower than high-viscosity composites. Results of color stability showed acceptable values up to 3 days aging except for ADM and FSF. ΔE was not influenced by pre-heating and, overall, ΔE: FS < VIT < FO < FSF < ADM < FBF. Only VIT and FS showed ΔE ≤ 3.3 (clinical threshold). Therefore, the effects of pre-heating depend on the material. The tested materials generally showed similar or enhanced properties after pre-heating (except ADM and VIT).

RESUMO

STATEMENT OF PROBLEM: When 3-dimensional printing casts, the operator can change the type of resin and the printing layer thickness, reducing the fabrication time. However, how these parameters affect the accuracy of 3-dimensionally printed casts is unknown. PURPOSE: The purpose of this in vitro study was to evaluate the accuracy of 3-dimensionally printed casts by using a stereolithography (SLA) 3-dimensional printer (Forms2) with 3 different layer thickness (25, 50, and 100 µm) and 2 different resins (Gray and Cast) and by comparing the time to obtain each cast. MATERIAL AND METHODS: One master cast was scanned, and a single file was printed several times. The printed casts were then scanned by using a laboratory scanner. The standard tessellation language (STL) files provided by the laboratory scanner were superimposed and compared by using a software program (Geomagic Control; 3D Systems). The 2-way ANOVA test was used for the trueness evaluation, followed by the Tukey test to identify differences among the groups (α=.05). RESULTS: No statistically significant differences in accuracy were found among the 3 different layers for either resin (P>.05). Printing time doubled as layer thickness decreased. CONCLUSIONS: This study showed that when printing casts, the fastest printing settings can be used without losing accuracy and that the laboratory digital workflow can be accelerated with selection of the resin and cast layer, as the type of resin and layer thickness did not influence the quality of the casts.

Assuntos

RESUMO

OBJECTIVE: This study evaluated the microshear bond strength of a resin cement to Y-TZP after different methods of TiO2 nanotubes (nTiO2) incorporation on pre-sintered Y-TZP surfaces. METHODS: nTiO2 were synthesized and incorporated on Y-TZP slices as follows (n = 15): 1) nTiO2 mixed with isopropyl alcohol/manual application (MAl); 2) nTiO2 mixed with acetone/manual application (MAc); 3) nTiO2 mixed with isopropyl alcohol/high-pressure vacuum application (HPVAl); 4) nTiO2 mixed with acetone/high-pressure vacuum application (HPVAc). As controls, surfaces were sandblasted with Al2O3 (OX) or Rocatec silicatization (ROC). All ceramics were sintered after nTiO2 incorporation. Surface treatments of OX and ROC were made after sintering. Surfaces were characterized by confocal laser microscopy, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Resin composite cylinders (1.40 mm diameter and 1 mm height) were cemented with a resin cement, stored in water at 37 °C for 24 h and thermocycled for 10 000 cycles before microshear bond strength evaluation. Data were analyzed with one-way ANOVA and Games-Howell (α = 0.05), and fracture analysis was performed using a stereomicroscope. RESULTS: EDS confirmed the presence of TiO2 on treated Y-TZP. The confocal analysis showed higher roughness for HPVAc and OX. There were significant differences between surface treatments (p < 0.001). HPVAl (22.96 ± 10.3), OX (34.16 ± 7.9) and ROC (27.71 ± 9.4) showed higher microshear bond strengths and were statistically similar (p > 0.05). MAC showed intermediary values, and HPVAc and MAl presented decreased bond strength, with a high percentage of premature debonding. CONCLUSION: High-pressure vacuum application of nTiO2 mixed with isopropyl alcohol was able to produce bond strength values compared to conventional air abrasion and Rocatec silicatization. SIGNIFICANCE: The infiltration of TiO2 nanostructures on the pre-sintered Y-TZP is an interesting approach that can improve bond strength without the need of sandblasting methods.

Assuntos

RESUMO

Background: Proanthocyanidin has been considered as a preventive agent against erosion because of its properties, which involves remineralization, reduction of demineralization and matrix metalloproteinases (MMPs) inhibition. Thus, the aim of this in situ study was to evaluate the effect of proanthocyanidin-based dentifrices on wear resistance of dentin specimens subjected to erosion associated with abrasion. Material and Methods: This crossover double-blinded study was performed in 5 phases of 5 days each, with 10 healthy volunteers who wore 5 palatal devices (1 for each phase) with 4 dentin specimens. The groups under study were: G1 - placebo dentifrice (negative control group); G2 - 0.012% chlorhexidine dentifrice (1st positive control group); G3 - NaF 1110 ppm fluoride dentifrice (2nd positive control group); G4 - 10% purified proanthocyanidin dentifrice (1st test group); G5 - fluoride + proanthocyanidin dentifrice (2nd test group). Erosion was performed by palatal device immersion in acid beverage (Coca-cola®), 3 times daily for 5 minutes during 5 days. Abrasion was applied after the first and third erosive cycles by using a eletric toothbrush during 15 seconds in each specimen with the application of the studied dentifrices slurry. The response variable was depth of dentin loss (µm) measured by profilometry. Data were analyzed by Repeated Measures Analysis of Variance followed by LSD Fisher's test (p<0.05). Results: Data (G1: 1.76 ± 0.55A; G2: 1.19 ± 0.42B; G3: 1.29 ± 0.34B; G4: 0.93 ± 0.38C; G5: 0.82 ± 0.34C) showed that G4 and G5 did not presented significant difference between them, but showed less dentine loss when compared to all other groups. G1 presented the highest dentin wear. Conclusions: Proanthocyanidin and the combination of proanthocyanidin and fluoride dentifrices revealed the best results, showing that these formulations could be a promising alternative for patients who suffer with dentin erosion. Key words:Dentin, erosion, cross-liking agent, metalloproteinases, toothpastes.

RESUMO

Endosseous implant surface topography directly affects adherent cell responses following implantation. The aim of this study was to examine the impact of nanoscale topographic modification of titanium implants on Osterix gene expression since this gene has been reported as key factor for bone formation. Titanium implants with smooth and nanoscale topographies were implanted in the femurs of Osterix-Cherry mice for 1-21 days. Implant integration was evaluated using scanning electron microscopy (SEM) to evaluate cell adhesion on implant surfaces, histology, and nanotomography (NanoCT) to observe and quantify the formed bone-to-implant interface, flow cytometry to quantify of Osterix expressing cells in adjacent tissues, and real-time PCR (qPCR) to quantify the osteoinductive and osteogenic gene expression of the implant-adherent cells. SEM revealed topography-dependent adhesion of cells at early timepoints. NanoCT demonstrated greater bone formation at nanoscale implants and interfacial osteogenesis was confirmed histologically at 7 and 14 days for both smooth and nanosurface implants. Flow cytometry revealed greater numbers of Osterix positive cells in femurs implanted with nanoscale versus smooth implants. Compared to smooth surface implants, nanoscale surface adherent cells expressed higher levels of Osterix (Osx), Alkaline phosphatase (Alp), Paired related homeobox (Prx1), Dentin matrix protein 1 (Dmp1), Bone sialoprotein (Bsp), and Osteocalcin (Ocn). In conclusion, nanoscale surface implants demonstrated greater bone formation associated with higher levels of Osterix expression over the 21-day healing period with direct evidence of surface-associated gene regulation involving a nanoscale-mediated osteoinductive pathway that utilizes Osterix to direct adherent cell osteoinduction.

Assuntos

RESUMO

STATEMENT OF PROBLEM: Intraoral scanners (IOSs) have some inherent distortions caused by optical and/or software imperfections. However, how other factors such as operator experience, scan time, scanner type, and scan size influence scan accuracy is not clear. PURPOSE: The purpose of this in vitro study was to evaluate the trueness and precision of scans performed by 3 professionals with different levels of experience by using 2 IOSs. MATERIAL AND METHODS: Three operators with low, medium, and high levels of experience scanned a master model 10 times by using 2 IOSs (CEREC Omnicam; Dentsply Sirona and TRIOS 3; 3Shape), resulting in 10 standard tessellation language files for each group (N=60). Each standard tessellation language file was divided into 2 areas (prepared teeth and complete arch). Precision was evaluated by comparing the 10 scans from each examiner for each system. Trueness was evaluated by comparing each scan file with a reference scan obtained from a laboratory scanner (D2000; 3Shape). A 3D analysis software program (Geomagic Control; 3D Systems) was used to perform all the comparisons and superimpositions. The 3-way ANOVA test followed by the Tukey HSD test were used to assess precision and trueness. The 2-way ANOVA followed by the Tukey HSD test was used to assess scan time. The Pearson correlation test was performed between scan time and trueness for both scanners. An additional correlation was performed between scan time and number of images, as well as between number of images and trueness for the TRIOS 3. RESULTS: Statistically significant influences of operator (P<.001), scanner (P<.001), scan size (P<.001), operator and scan size (P<.001), and scanner and scan size (P<.001) were observed. The TRIOS 3 group reported higher precision than the CEREC Omnicam group for complete-arch scans (P<.001), although no difference was observed for scans of the prepared tooth. Medium- (P=.002) and low-experience operators (P<.001) reported lower precision for complete-arch scans performed with CEREC Omnicam when compared with TRIOS 3. The low-experience operator reported significantly worse results for complete-arch scans in comparison with the medium- (P=.008 and P<.001) and high-experience operators (P<.001 and P=.001), by using TRIOS 3 and CEREC Omnicam, respectively. Medium- and high-experience operators reported similar results among themselves. The CEREC Omnicam scanner reported lower trueness for complete-arch scans when compared with the prepared tooth (P<.001); for TRIOS 3, a difference was only observed for the low-experience operator when compared with the high-experience operator (P<.001). The CEREC Omnicam reported lower trueness than the TRIOS 3, except for the medium-experience operator with the prepared tooth scan. Comparing the trueness between operators and considering the same scanner and scan size, all groups were similar. The low-experience operator had a longer scanning time than the medium- and high-experience operators. For TRIOS 3, the low-experience operator obtained the highest number of images during each scan. CONCLUSIONS: The accuracy of intraoral scans was influenced by operator experience, type of IOSs, and scan size. More experienced operators and smaller scan sizes made for more accurate scans. In addition, more experienced operators made faster scans, and the TRIOS 3 was more accurate than the CEREC Omnicam for complete-arch scans.

Assuntos

RESUMO

STATEMENT OF PROBLEM: Information related to the optical and surface properties, including health compatibility, surface roughness, and esthetics, of 3D-printed dental materials is scarce. PURPOSE: The purpose of this in vitro study was to compare the physical and surface properties of a 3D-printed resin with those of materials used for interim restorations. MATERIAL AND METHODS: A 3D-printed resin (PR) (NextDent C&B MFH; 3D Systems), an autopolymerizing interim material (BA) (Protemp 4; 3M ESPE), and a composite resin (Z350) (Filtek Z350XT; 3M ESPE) were tested for degree of color change (ΔE) (n=7) at different timepoints-24 hours after polishing/baseline (P0), 8 days after polishing (P1), and after artificial aging in water at 60 °C for 24 hours (P2)-by using a CIELab-based colorimeter; flexural strength (σ) (n=10) with a 3-point bend test; Knoop hardness (H) (n=8); and surface roughness (Ra) (n=7) with a profilometer. All specimens were polished 24 hours after polymerization, except for the additional group for surface roughness (BA) without polishing (BANP). A statistical analysis was performed by using 2-way repeated-measures ANOVA followed by the Fischer test for ΔE and 1-way ANOVA followed by the Fisher test for microhardness and surface roughness (α=.05). RESULTS: The Z350 showed the highest values for σ and H, followed by PR. BA showed the lowest results for both tests (P<.05). Considering roughness, the Z350 showed similar values to those of BA but lower than PR; PR showed similar roughness when compared with BA. PR showed the highest color variation among the groups at all timepoints, followed by BA. The Z350 was the most color stable material at all timepoints. CONCLUSIONS: The 3D-printed composite resin had adequate mechanical and surface properties for an interim restorative material. It has the potential to be a low-cost workflow in dentistry, although its color stability could be a concern for long-term use.

Assuntos

RESUMO

Avaliar o efeito da ativação ultrassônica e do veículo do MTA no pH dentinário em dentes com reabsorção radicular externa simulada. Métodos: Uma cavidade foi preparada na superfície radicular de 46 dentes bovinos, as quais foram seladas com MTA preparado com 100% de água destilada (DW) ou com 80% DW e 20% de propilenoglicol (PG). Os dentes foram divididos em quatro grupos (n = 10), de acordo com o veículo e o protocolo de ativação ultrassônica utilizado durante a inserção do material (ativação ou sem ativação). O grupo controle (n = 6) foi deixado sem selamento. O pH foi mensurado após 15, 30 e 60 dias de imersão. Resultados: A ativação com ultrassom não alterou significativamente o pH (p>0,05). Os cimentos manipulados utilizando DW + PG apresentaram maior pH aos 15 dias, em relação ao MTA manipulado com DW (p<0,05). Conclusão: A associação de 80% de água destilada com 20% de propilenoglicol aumentou o pH dentinário, o que é positivo para o reparo de reabsorções radiculares (AU).

The aim of this study was to evaluate the effect of ultrasonic activation and MTA vehicle on dentinal pH in simulated external root resorptions. So, a cavity was prepared in the root of forty-six bovine teeth. They were filled with MTA mixed with 100% distilled water (DW) or MTA mixed with 80% DW and 20% propylene glycol (PG). Teeth were divided into four groups (n = 10), according to the vehicle (DW or PG) and ultrasonic protocol used for material insertion (activated or not). Control group (n = 6) was unfilled. The pH was assessed after 15, 30 and 60 days of immersion. As results of all that, activation with ultrasound did not significantly alter the pH (p > 0.05). The cements were mixed with either DW or DW + PG, with the later association presenting higher pH at 15 days of assessment than the former (p < 0.05). Thereby, it can be concluded that mixing MTA with 80% DW and 20% PG increased the dentinal pH, which is positive for root resorption repair (AU).

Assuntos

RESUMO

The quality of the micromechanical retention between the enamel prisms exposed through acid etching and adhesive system can be influenced by the relationship between the angle of the exposed enamel prisms and the external surface/restorative material. Therefore, the aim of the present study was to determine the influence of the enamel cavosurface beveling in different cavity sizes on the angle relation between enamel prisms and the restorative material. For this research, 30 human permanent molars were used and divided into three groups according the isthmus aperture of class I cavities (1/4, 1/3, and 1/2 of the intercuspal distance). Cavosurface angle beveling was performed in each tooth buccal or palatal/lingual side, and a resin composite restoration was placed. Each restored tooth was sectioned in buccal/palatal direction followed by analysis in scanning electron microscope. Means of the angles observed between enamel prisms and the restorative material were registered and statistically analyzed by Kruskal-Wallis test. Results showed higher mean angle values for beveled groups when comparing with the values observed in the unbeveled margins (p < .05) regardless of the isthmus aperture, being 1/4 (beveled = 48.36°; unbeveled = 20.71°), 1/3 (beveled = 39.75°; unbeveled = 29.15°), and 1/2 (beveled = 37.02°; unbeveled = 26.34°). It was also observed that in some unbeveled cavities, there were the presence of laterally exposed enamel prisms (0°), mainly in more conservative cavities. It was concluded that the presence of higher angles values occurred in the samples with beveled margins, without presence of laterally exposed enamel prisms.

RESUMO

Aim: To evaluate the color stability of bovine enamel with artificial white spot lesions treated with resin infiltration (ICON) or remineralization with fluoride using two storage methods. Methods: Sixty incisors were submitted to artificial white spot lesion induced by demineralization-remineralization (DE-RE) cycling. Initial color was evaluated with CIE-Lab to measure ΔEab. Demineralized teeth were divided according to the treatment of the white spot lesion (n = 20): 1) Remineralization with 2% neutral fluoride gel for 4min (control); 2) ICON application following manufacturer's recommendations; and 3) ICON with decreased drying time after the application of ethanol. After 24h, color was evaluated and samples were subdivided (n = 10) according to storage: 1) distilled water for 1 month; 2) grape juice for 10min daily. After storage, color was evaluated. L*, a* and b* data were analyzed by one-way ANOVA and ∆Eab data by two-way ANOVA followed by Tukey's HSD (α = 0.05). Results: L* was affected by juice storage, and decreased when ICON was applied with decreased drying time after the ethanol application. The same behavior occurred with a* (increase with reduced drying time), while b* was not affected. For ∆Eab significant differences were observed between groups (p = 0.0219) and storage methods (p = 0.0007). There was no interaction effect (p = 0.1118). Remineralization with fluoride presented the lowest color changes after storage in water. Conclusion: Treatment of artificial carious lesions with resin infiltration presented greater color changes than fluoride remineralization after storage in both solutions in vitro

Assuntos

RESUMO

OBJECTIVE: Extensive restorations in posterior teeth always bring doubts to the clinicians regarding the best protocol, mainly when structures of reinforcement were lost. OBJECTIVE: This study aimed to evaluate the effect of beveling on the fracture resistance and pattern of class II (MOD) restored teeth. METHODOLOGY: Ninety human premolars were randomly assigned into 9 groups: CTR (control/sound); NC (cavity preparation, non-restored); RU (restored, unbeveled); RTB (restored, entire angle beveling); RPB (restored, partial/occlusal beveling); EC (endodontic access/EA, non-restored); EU (EA, unbeveled); ETB (EA, entire angle beveling); EPB (EA, partial/occlusal beveling). Teeth were restored with Esthet X resin composite and stored in distilled water for 24 h before the inclusion in PVC cylinders. The axial loading tests were performed with 500 kgF at 0.5 mm/min crosshead speed until fracture of the specimens. Fracture resistance and pattern were accessed and data were analyzed using one-way ANOVA and Tukey's HSD test (α=0.05). RESULTS: Mean (±SD) failure loads ranged from 136.56 (11.62) to 174.04 (43.5) kgF in the groups tested without endodontic access. For endodontically accessed teeth, fracture resistance ranged from 95.54 (13.05) to 126.51 (19.88) kgF. Beveling of the cavosurface angle promoted the highest fracture resistance values (p<0.05) and prevented catastrophic fractures. CONCLUSIONS: Cavosurface angle beveling is capable of improving fracture resistance and pattern for both endodonticaly accessed and non-accessed teeth.

Assuntos

RESUMO

The aim of this study is to evaluate the machinability of four CAD/CAM materials (n = 13) assessed by brittleness index, Vickers hardness, and fracture toughness and interaction among such mechanical properties. The materials selected in this in vitro study are Feldspathic ceramic [FC], Lithium-disilicate glass ceramic [LD], leucite-reinforced glass ceramic [LR], and nanofilled resin material [RN]. Slices were made from the blocks following original dimensions 14 × 12 × 3 mm (L × W × H), using a precision slow-speed saw device and then surfaces were regularized through a polishing device. Brittleness index and fracture toughness were calculated by the use of specific equations for each one of the properties. The Vickers hardness was calculated automated software in the microhardness device. One-way Anova and Pearson's correlation were applied to data evaluation. LD obtained the highest values for brittleness index and was not significantly different from FC. LR presented statistically significant difference compared with RN, which had the lowest mean. Vickers hardness showed LD with the highest average, and no statistical difference was found between FC and LR. RN presented the lowest average. Fracture toughness showed FC and LR not statistically different from each other, likewise LD and RN. The brittleness index, considered also as the machinability of a material, showed within this study as positively dependent on Vickers hardness, which leads to conclusion that hardness of ceramics is related to its milling capacity. In addition, fracture toughness of pre-sintered ceramics is compared to polymer-based materials.

Assuntos

RESUMO

Bulk-fill composites were introduced in dentistry to accelerate clinical procedures while providing adequate outcomes. Concerns regarding the use of bigger composite increments rely on the polymerization shrinkage and shrinkage stress, which may generate gaps on the adhesive interface and result in a reduced success rate. OBJECTIVE: To evaluate the polymerization shrinkage stress of different bulk-fill resin composites and their elastic modulus. MATERIALS AND METHODS: Fourteen specimens were made for each of the nine different resin composites (seven with 12 mm3 and seven with 24 mm3): Surefill SDR flow (SDR), X-tra Base (XB), Filtek Bulk Fill Flowable (FBF), Filtek Z350XT Flow (Z3F); Tetric Evo Ceram Bulk Fill (TBF), X-tra Fil (XF), Filtek Bulk Fill (FBP), Admira Xtra Fusion (ADM) and Filtek Z350 XT (Z3XT). Linear shrinkage stress was evaluated for 300 s with the aid of a linear shrinkage device adapted to a Universal Testing Machine. For each composite group, seven additional specimens (2x2x25 mm) were made and Young's modulus was evaluated with a 3-point bending device adapted in a Universal Testing Machine with 0.5 mm/min crosshead speed and 50 KgF loading cell. RESULTS: For 12 mm3 specimens, three-way ANOVA showed that only SDR and TBF generated lower stress after 20 s. Considering 300 s, TBF, SDR, and XF generated the lowest stress, followed by ADM, FBP, XB, and FBF, which were similar to Z3XT. Z3F generated the highest stress values for all time points. Considering 24 mm3 specimens after 20 s, all bulk fill composites generated lower stress than Z3XT, except XB. After 300 s, SDR, FBP, and ADM generated the lowest stress, followed by TBF and XF. For elastic modulus, one-way ANOVA showed that FBF, SDR, Z3F, and ADM presented the lowest values, followed by XB and TBF. FBP, Z3XT, and XF presented the highest elastic modulus among the evaluated composites. CONCLUSIONS: Bulk-fill resin composites presented equal to lower shrinkage stress generation when compared to conventional composites, especially when bigger increments were evaluated. Bulk-fill composites showed a wide range of elastic modulus values, but usually similar to "regular" composites.

Assuntos

RESUMO

Abstract: The aim of this study is to evaluate the machinability of four CAD/CAM materials (n = 13) assessed by brittleness index, Vickers hardness, and fracture toughness and interaction among such mechanical properties. The materials selected in this in vitro study are Feldspathic ceramic [FC], Lithium-disilicate glass ceramic [LD], leucite-reinforced glass ceramic [LR], and nanofilled resin material [RN]. Slices were made from the blocks following original dimensions 14 × 12 × 3 mm (L × W × H), using a precision slow-speed saw device and then surfaces were regularized through a polishing device. Brittleness index and fracture toughness were calculated by the use of specific equations for each one of the properties. The Vickers hardness was calculated automated software in the microhardness device. One-way Anova and Pearson's correlation were applied to data evaluation. LD obtained the highest values for brittleness index and was not significantly different from FC. LR presented statistically significant difference compared with RN, which had the lowest mean. Vickers hardness showed LD with the highest average, and no statistical difference was found between FC and LR. RN presented the lowest average. Fracture toughness showed FC and LR not statistically different from each other, likewise LD and RN. The brittleness index, considered also as the machinability of a material, showed within this study as positively dependent on Vickers hardness, which leads to conclusion that hardness of ceramics is related to its milling capacity. In addition, fracture toughness of pre-sintered ceramics is compared to polymer-based materials.

Assuntos

RESUMO

Abstract Extensive restorations in posterior teeth always bring doubts to the clinicians regarding the best protocol, mainly when structures of reinforcement were lost. Objective This study aimed to evaluate the effect of beveling on the fracture resistance and pattern of class II (MOD) restored teeth. Methodology Ninety human premolars were randomly assigned into 9 groups: CTR (control/sound); NC (cavity preparation, non-restored); RU (restored, unbeveled); RTB (restored, entire angle beveling); RPB (restored, partial/occlusal beveling); EC (endodontic access/EA, non-restored); EU (EA, unbeveled); ETB (EA, entire angle beveling); EPB (EA, partial/occlusal beveling). Teeth were restored with Esthet X resin composite and stored in distilled water for 24 h before the inclusion in PVC cylinders. The axial loading tests were performed with 500 kgF at 0.5 mm/min crosshead speed until fracture of the specimens. Fracture resistance and pattern were accessed and data were analyzed using one-way ANOVA and Tukey's HSD test (α=0.05). Results Mean (±SD) failure loads ranged from 136.56 (11.62) to 174.04 (43.5) kgF in the groups tested without endodontic access. For endodontically accessed teeth, fracture resistance ranged from 95.54 (13.05) to 126.51 (19.88) kgF. Beveling of the cavosurface angle promoted the highest fracture resistance values (p<0.05) and prevented catastrophic fractures. Conclusions Cavosurface angle beveling is capable of improving fracture resistance and pattern for both endodonticaly accessed and non-accessed teeth.

Assuntos

RESUMO

BACKGROUND: The use of hybrid-light (HL) during in-office teeth bleaching can provide faster and reliable results after a single bleaching session, especially if associated with previous acid etching. The present in vivo, interventional, split-mouth, triple-blinded and randomized study evaluated the efficiency of a HL, with and without prior enamel acid etching, assessing the gel application time, degree of color change, sensitivity and treatment stability up to 12 months. METHODS: Thirty-four patients were selected and randomly divided into four groups. The color was evaluated using a spectrophotometer with the CIELab color system, and a VAS questionnaire was used to evaluate the sensitivity. Both upper and lower hemiarches (GI and III) received enamel acid etching with 37% phosphoric acid for 15 s prior to the application of 35% hydrogen peroxide gel (HP). For GI and II, HP was applied on both dental arches for 3-4 consecutive applications and activated by HL (2 × 3' activations with 1' interval); and 3 × 15' (HP) for GIII and IV without HL. Patients returned in 24 h, 1 week, 1-, 6- and 12-months intervals. The clinical operator was different from the clinical measurements operator. RESULTS: After 3-way ANOVA, Tukey's, Wilcoxon and Mann-Whitney tests, all with p < 0.05, no statistical differences were observed between the groups regarding color change (ΔE) and sensitivity in all evaluations. The lowest gel application time was observed for GII (acid etch + HL), followed by GI (HL). CONCLUSIONS: The present study's results reveal the advantages of HL associated with acid etching prior to in office bleaching.

Assuntos

RESUMO

PURPOSE: To evaluate the color change caused by post-irradiation conversion (ΔE24h and ΔE8 days ) and artificial aging (ΔEAGING ) of resin cements light activated through ceramics of different opacities immediately and 6 minutes after manipulating the material. MATERIALS AND METHODS: Resin cement disks (Allcem and LuxaCore) were light activated through ceramics (without ceramic, e.max HT, LT, and MO) immediately and 6 minutes after the manipulation (n = 10). Spectrophotometry was used to evaluate ΔE24h and ΔE8 days after 37˚C-dry-dark-storage for 24 hours and 8 days, and ΔEAGING after 60˚C-water-storage for 24 hours. Data were analyzed with three-way ANOVA and Tukey's HSD (α = 0.05). RESULTS: Regarding the post-irradiation color change, significant differences were found between the cements (p < 0.0001), light activation protocols (p = 0.037), and ceramics (p < 0.001). The immediate activation (16.2 ± 0.1) showed lower ΔE values than the delayed activation (16.5 ± 0.1). Ceramics influenced the ΔE values as follows: MO (14.0 ± 1.2) < LT (14.9 ± 1.2) ≈ HT (15.4 ± 1.2) < control (21.2 ± 1.2). Regarding ΔEAGING , significant differences were found between cements (p < 0.001), light activation (p = 0.006), and ceramics (p < 0.001). The delayed activation (8.4 ± 0.1) showed lower values than the immediate activation (8.9 ± 0.1). Ceramic spacers influenced ΔEAGING as follows: control (5.6 ± 0.2) < MO (6.6 ± 0.2) < HT (11.0 ± 0.2) ≈ LT (11.5 ± 0.2). CONCLUSION: The delayed light activation resulted in increased color stability, while the ceramic interposition resulted in lower color stability.

Assuntos

RESUMO

Often, young patients (≤30 years old) present with carious lesions that progress acutely, compromising a large amount of tooth structure. In these cases, a treatment to prevent the occurrence of pulp exposure and promote remineralization of caries-affected dentin is necessary to maintain healthy dental structure and allow more conservative interventions. The approach will be different when pulp exposure occurs: The therapeutic treatments will be focused on reparative dentin formation and prevention of microorganisms penetrating the pulp organ. Due to the different possible treatments that can be performed to avoid pulp necrosis and the various materials that can be used for this purpose, professionals may have some difficulties understanding all the indications for conservative pulp treatments. The objective of this article is to describe and discuss a successful pulp capping and stepwise excavation associated with restorative treatment for deep caries lesions of anterior upper teeth.

Assuntos

RESUMO

A pigmentação melânica gengival é uma condição clínica mais prevalente em indivíduos da raça negra e oriental, consistindo frequentemente em um problema estético. Embora a recidiva seja imprevisível, vários tratamentos são propostos, entre eles a mucodermoabrasão com diferentes instrumentos. O objetivo do presente relato de caso clínico foi demonstrar duas técnicas para resolução desses casos: emprego dos gengivótomos e de uma ponta de cerâmica em alta rotação.

Gingival melanin pigmentation is a clinical condition, more prevalent in oriental and black people, and may generate esthetical problems. Despite the fact that recurrence is unpredictable, different treatments are proposed, such as epithelial abrasion with different instruments. The objective of the present case report is to show two different techniques for resolution of such cases: use of Kirkland periodontal knife, and abrasive ceramic burs in high speed.

Assuntos

RESUMO

Introduction: Fractures of the anterior teeth consists of a clinical condition that generates not only aesthetic and psychological problems, but may also cause dental pain. Thus, the affected teeth should be treated as urgencies in dental offices and their resolution whenever possible should be in a single session. Direct resin composite restorations should wherever possible be preferred due to the speed and possibility of obtaining good results. Objective: The objective of this case report is to describe the clinical sequence for restoration of a maxillary central incisor that presented a crown fracture using an immediate insert technique for resin composite (a "free hand" technique) with a modification to obtain dentin layer. Case report: A patient sought treatment after she fractured tooth #21. The restoration was performed with resin composite using the immediate technique. To facilitate the layering technique, the immediate insertion technique was changed for making the dentin lobes with the aid of a Teflon tape and the support with the index finger. Conclusion: The restoration of fractured anterior teeth can be performed quickly with the use of resin composites of different opacities and the use of the technique of immediate insertion proposed in this case report.