RESUMO
In this work, a fiber laser refractometer based on a fiber ball lens (FBL) interferometer is proposed. The linear cavity erbium-doped fiber laser uses an FBL structure acting as a spectral filter and sensing element for determining the RI of a liquid medium surrounding the fiber. The optical interrogation of the sensor is the wavelength displacement of the generated laser line as a function of the RI variations. For the proposed FBL interferometric filter, the free spectral range of its wavelength-modulated reflection spectrum is adjusted to maximum in order to obtain RI measurements in a range of 1.3939 to 1.4237 RIU, from laser wavelength displacements in a range from 1532.72 to 1565.76 nm. The obtained results show that the wavelength of the generated laser line is a linear function of the RI variations on the medium surrounding the FBL with a sensitivity of 1130.28 nm/RIU. The reliability of the proposed fiber laser RI sensor is analytically and experimentally investigated.
RESUMO
The use of titanium oxynitride (TiOxNy) thin films as a saturable absorber (SA) element for generation of passive Q-switched (PQS) laser pulses, from a linear cavity Er-Yb double-clad fiber (EYDCF) laser, is demonstrated. Additionally, the deposition of the material as a thin film covering a fiber micro-ball lens (MBL) structure is reported for the first time. The TiOxNy coating is deposited by a direct current (DC) magnetron-sputtering technique. The MBL is inserted within the laser cavity in a reflection configuration, alongside a reflecting mirror. As a result, the coated fiber MBL simultaneously acts as a SA element for PQS laser pulses generation and as an interference filter for wavelength selection and tuning of the generated laser line. Tunable single-laser emission in a wavelength range limited by dual-wavelength laser generation at 1541.96 and 1547.04 nm is obtained. PQS laser pulses with a repetition rate from 18.67 to 124.04 kHz, minimum pulse duration of 3.57 µs, maximum peak power of 0.359 W, and pulse energy of 1.28 µJ were obtained in a pump power range from 1 to 1.712 W.
RESUMO
In this work, we demonstrated lossy mode resonance (LMR) generation in optical fiber structures based on multimode fibers coated with aluminum-doped zinc oxide (AZO) films. AZO thin films were deposited by using radio frequency magnetron sputtering. In order to exhibit the usefulness of the LMR effect for sensing applications in optical fiber based systems, the deposition conditions of the AZO film coatings were set to obtain the second LMR order within the 1.55 µm wavelength range. An optical transmission configuration setup was used to investigate the LMR effect on fiber structures based on the use of no-core and cladding-removed multimode fibers coated with AZO films synthesized from metallic sputtering targets with different proportions of Zn:Al, 92:8% and 98:2%, at atomic concentrations. The optical and electrical/chemical features of the AZO films were characterized with UV-vis and XPS spectroscopy, respectively. The optical response of the proposed sensing configuration to refractive index (RI) variations was experimentally demonstrated. For the best approach, the sensitivity of wavelength displacement to RI variations on the liquid surrounding media was found to be 1214.7 nm/RIU.
RESUMO
An all-fiber curvature laser sensor by using a novel modal interference in-fiber structure is proposed and experimentally demonstrated. The in-fiber device, fabricated by fusion splicing of multimode fiber and double-clad fiber segments, is used as wavelength filter as well as the sensing element. By including a multimode fiber in an ordinary modal interference structure based on a double-clad fiber, the fringe visibility of the filter transmission spectrum is significantly increased. By using the modal interferometer as a curvature sensitive wavelength filter within a ring cavity erbium-doped fiber laser, the spectral quality factor Q is considerably increased. The results demonstrate the reliability of the proposed curvature laser sensor with advantages of robustness, ease of fabrication, low cost, repeatability on the fabrication process and simple operation.