RESUMO
It is crucial to monitor the levels of Non-Ionizing Radiation (NIR) to which the general population may be exposed and compare them to the limits defined in the current standards, in view of the rapid rise of communication services and the prospects of a connected society. A high number of people visits shopping malls and since these locations usually have several indoor antennas close to the public, it is therefore a kind of place that must be evaluated. Thus, this work presents measurements of the electric field in a shopping mall located in Natal, Brazil. We proposed a set of six measurement points, following two criteria: places with great the flow of people and the presence of one or more Distributed Antenna System (DAS), co-sited or not with WiFi access points. Results are presented and discussed in terms of the distance to DAS (conditions: near and far) and flow density of people in the mall (scenarios: low and high number of people). The highest peaks of electric field measured were 1.96 and 3.26 V/m, respectively corresponding to 5% and 8% of the limits defined by the International Commission on Non-Ionizing Radiation Protection (ICNIRP) and the Brazilian National Telecommunication Agency (ANATEL).
Assuntos
Eletricidade , Telecomunicações , Humanos , Brasil , Radiação não IonizanteRESUMO
Waste tire rubber (WTR) has been extensively generated worldwide due to mobility needs growth. About 1.5 billion units are generated annually, constantly discharged in the environment with a few reusability alternatives. Therefore, rubber recovery methods and these residues' transformation into a cost-effective product have gained attention. Aiming to minimize the usage of fossil resources and contributes to a circular economy, it was analyzed the usage of WTR particles (5-20% by weight) in castor oil-based polyurethane foams under natural aging to promote a holistic view of all factors involved in the performance of the foams. Morphological, thermal, chemical, and mechanical properties were determined before and after exposure to open air to observe the impact of photo-oxidation and hydrolysis. The increase in viscosity of pre-polymer during the rubber loading produced greater density foams with smaller cell sizes than neat PU, in which the average cell size increased after the weathering. The rubber contributes to enhancing the compressive behavior in the non-exposed samples. After exposure, the results suggest that degradation may act to increase the crosslinking density even with the presented structural changes such as yellowing and voids. Regarding thermal stability, the rubber promotes a slight decay in the ability to resist a heat flow before and after weathering. Still, the char yield increased, showing a possibility of better fire retardancy for composites. FTIR and UV-vis showed chemical structure changes as Photo-Fries network rearrangement, Norrish I random chain scission, and Norrish II ß-scission. Besides, UV-vis revealed the maximum absorbance in the UVB region, showing that the PU reinforced by WTR can be a promising material for civil coatings.
Assuntos
Óleo de Rícino , Poliuretanos , Borracha , ViscosidadeRESUMO
Waste tire rubber is produced on a large scale in the automotive industry and is considered difficult to recycle because they have iron, nylon, polyester, and chemical structure formed by cross-links. In this way, the waste is almost always deposited in inappropriate places or incorrectly burned, causing a series of environmental problems. The objective of this work was to analyze the viability of the use of waste tire rubber (5, 10, and 20% m/m) reinforced in polyurethane foam (PU) derived from castor oil to obtain composites, as an alternative for raw materials petrochemical industrial. The materials were characterized by scanning electron microscopy (SEM), optical microscopy (OM), apparent density, contact angle, water absorption, X-ray diffractometry (XRD), spectroscopy infrared (FTIR), thermogravimetry (TGA) techniques, and mechanical tests. The results showed that the residue of the rubber powder reinforced with polyurethane caused an increase in the density of the composites when compared to pure PU, which directly influenced the morphological, physical, thermal, and mechanical properties. This fact occurred because with the insertion of rubber powder in the PU there was a decrease in cell size and increase of pore volume. The TG and DTG analyzes showed that the insertion of the rubber powder improved the thermal stability of the composite when compared to pure PU, as well as impact tests and contact angle.
Assuntos
Óleo de Rícino , Poliuretanos , Reciclagem , Borracha , TermogravimetriaRESUMO
Pentavalent antimonial (SbV) is the first treatment for cutaneous leishmaniasis (CL). Other drugs present similar side effects and higher cost. Oral miltefosine is effective to treat kala-azar. The aim of the present study was to compare the efficacy of glucamine (SbV) plus topical miltefosine with glucamine in the treatment of CL. Eighty isogenic C57BL/6 mice were inoculated with Leishmania (Leishmania) amazonensis and divided into two groups: one group was treated with SbV associated with miltefosine, and the other group received SbV plus saline solution. Groups were evaluated according to the diameter of the inoculated foot pad, the culture, and the parasite count using the limiting dilution assay. There was not statistical difference. The efficacy of glucamine in CL treatment did not increase when associated with topical miltefosine.(AU)