RESUMO

The presence of pharmaceuticals in wastewater resulting from human activities has driven researchers to explore effective treatment methods such as adsorption using activated carbon (AC). While AC shows promise as an adsorbent, further studies are essential to comprehend its entire interaction with pharmaceuticals. This article investigates the adsorption of potassium diclofenac (PD) onto AC using experimental and modeling approaches. Batch adsorption studies coupled with Fourier transform infrared spectroscopy (FTIR) were employed to clarify the adsorption mechanism of PD on AC. Various kinetic and isotherm adsorption models were applied to analyze the adsorbent-adsorbate interaction. The kinetics were best described by Avrami's fractional order (AFO) nonlinear model. Also, the intraparticle diffusion (IP) model reveals a three-stage adsorption process. The experimental equilibrium data fitted well with the three-parameter nonlinear Liu model, indicating a maximum adsorption capacity (Qmax) of 88.45 mg g-1 and suggesting monolayer or multilayer adsorption. Thermodynamic analysis showed favorable adsorption (ΔG° < 0), with an enthalpy change (ΔH° = -30.85 kJ mol-1) characteristic of physisorption involving hydrogen bonds and π-π interactions. The adsorption mechanism was attributed to forming a double layer (adsorbate-adsorbent and adsorbate-adsorbate).

Assuntos

RESUMO

This work aimed to describe the adsorption behavior of Congo red (CR) onto activated biochar material prepared from Haematoxylum campechianum waste (ABHC). The carbon precursor was soaked with phosphoric acid, followed by pyrolysis to convert the precursor into activated biochar. The surface morphology of the adsorbent (before and after dye adsorption) was characterized by scanning electron microscopy (SEM/EDS), BET method, X-ray powder diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) and, lastly, pHpzc was also determined. Batch studies were carried out in the following intervals of pH = 4-10, temperature = 300.15-330.15 K, the dose of adsorbent = 1-10 g/L, and isotherms evaluated the adsorption process to determine the maximum adsorption capacity (Qmax, mg/g). Kinetic studies were performed starting from two different initial concentrations (25 and 50 mg/L) and at a maximum contact time of 48 h. The reusability potential of activated biochar was evaluated by adsorption-desorption cycles. The maximum adsorption capacity obtained with the Langmuir adsorption isotherm model was 114.8 mg/g at 300.15 K, pH = 5.4, and a dose of activated biochar of 1.0 g/L. This study also highlights the application of advanced machine learning techniques to optimize a chemical removal process. Leveraging a comprehensive dataset, a Gradient Boosting regression model was developed and fine-tuned using Bayesian optimization within a Python programming environment. The optimization algorithm efficiently navigated the input space to maximize the removal percentage, resulting in a predicted efficiency of approximately 90.47% under optimal conditions. These findings offer promising insights for enhancing efficiency in similar removal processes, showcasing the potential of machine learning in process optimization and environmental remediation.

Assuntos

RESUMO

This study explored the effects of solution pH, biosorbent dose, contact time, and temperature on the Pb(II) biosorption process of natural and chemically treated leaves of A. compressa K. (Raw-AC and AC-OH, respectively). The results show that the surface characteristics of Raw-AC changed following alkali treatment. FT-IR analysis showed the presence of various functional groups on the surface of the biosorbent, which were binding sites for the Pb(II) biosorption. The nonlinear pseudo-second-order kinetic model was found to be the best fitted to the experimental kinetic data. Adsorption equilibrium data at pH = 2-6, biosorbents dose from 5 to 20 mg/L, and temperature from 300.15 to 333.15 K were adjusted to the Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models. The results show that the adsorption capacity was enhanced with the increase in the solution pH and diminished with the increase in the temperature and biosorbent dose. It was also found that AC-OH is more effective than Raw-AC in removing Pb(II) from aqueous solutions. This was also confirmed using artificial neural networks and genetic algorithms, where it was demonstrated that the improvement was around 57.7%. The nonlinear Langmuir isotherm model was the best fitted, and the maximum adsorption capacities of Raw-AC and AC-OH were 96 mg/g and 170 mg/g, respectively. The removal efficiency of Pb(II) was maintained approximately after three adsorption and desorption cycles using 0.5 M HCl as an eluent. This research delved into the impact of solution pH, biosorbent characteristics, and operational parameters on Pb(II) biosorption, offering valuable insights for engineering education by illustrating the practical application of fundamental chemical and kinetic principles to enhance the design and optimization of sustainable water treatment systems.

Assuntos

RESUMO

A grafting of N1-(3-trimethoxysilylpropyl)diethylenetriamine (TMSPDETA) on natural clay was carried out to obtain an organic-inorganic hybrid clay material that was applied as an adsorbent to the uptake of Reactive Blue 19 (RB-19) and Reactive Green 19 (RG-19) dyes from aqueous wastewaters. This research demonstrates the effect of TMSPDETA contents on amino-functionalized clay materials' hydrophobic/hydrophilic behavior. The resultant material was utilized to uptake reactive dyes in aqueous solutions. The clay@TMSPDETA hybrid material was characterized by isotherm of adsorption and desorption of nitrogen, FTIR, elemental analysis, TGA, pHpzc, total acidity, total basicity groups, and hydrophilic balance. The hybrid samples were more hydrophilic than the pristine clay for ratios from 0.1 up to 0.5 due to adding amino groups to the pristine clay. FTIR spectra suggest that TMSPDETA was grafted onto the clay. The hybrid material presents a surface area 2.17-fold (42.7 m2/g) lower than pristine clay (92.7 m2/g). The total volume of pores of hybrid material was 0.0822 cm3/g, and the pristine clay material was 0.127 cm3/g, corresponding to a diminution of the total pore volume (Vtot) of 1.54 times. The kinetic data followed the pseudo-second-order (PSO) model for RB-19 and RG-19 reactive dyes. The equilibrium data were better fitted to the Liu isotherm model, displaying a Qmax as 178.8 and 361.1 mg g-1 for RB-19 and RG-19, respectively, at 20.0 °C. The main mechanism of interactions of the reactive dyes with the hybrid clay is electrostatic interaction. The clay@TMSPDETA has a very good effect on treating synthetic dye-textile wastewater. The removal percentage of simulated wastewater was up to 97.67% and 88.34% using distilled water and plastic industry wastewater as the solvents, respectively. The clay@TMSPDETA-0.1 could be recycled up to 5 cycles of adsorption and desorption of both dyes, attaining recoveries of 98.42% (RB-19) and 98.32% (RG-19) using 0.1 M HCl + 10% ethanol.

Assuntos

RESUMO

The Brazil nut shell was used as a precursor material for preparing activated carbon by chemical activation with potassium hydroxide. The obtained material (BNSAC) was characterized, and the adsorptive features of phenol were investigated. The characterization showed that the activated carbon presented several rounded cavities along the surface, with a specific surface area of 332 m2 g-1. Concerning phenol adsorption, it was favored using an adsorbent dosage of 0.75 g L-1 and pH 6. The kinetic investigation revealed that the system approached the equilibrium in around 180 min, and the Elovich model represented the kinetic curves. The Sips model well represented the equilibrium isotherms. In addition, the increase in temperature from 25 to 55 °C favored the phenol adsorption, increasing the maximum adsorption capacity value (qs) from 83 to 99 mg g-1. According to the estimated thermodynamic parameters, the adsorption was spontaneous, favorable, endothermic, and governed by physical interactions. Therefore, the Brazil nut shell proved a good precursor material for preparing efficient activated carbon for phenol removal.

Assuntos

RESUMO

This paper proposes an easy and sustainable method to prepare high-sorption capacity biobased adsorbents from wood waste. A biomass wood waste (spruce bark) was employed to fabricate a composite doped with Si and Mg and applied to adsorb an emerging contaminant (Omeprezole) from aqueous solutions, as well as synthetic effluents loaded with several emerging contaminants. The effects of Si and Mg doping on the biobased material's physicochemical properties and adsorptive performance were evaluated. Si and Mg did not influence the specific surface area values but impacted the presence of the higher number of mesopores. The kinetic and equilibrium data presented the best fitness by the Avrami Fractional order (AFO) and Liu isotherm models, respectively. The values of Qmax ranged from 72.70 to 110.2 mg g-1 (BP) and from 107.6 to 249.0 mg g-1 (BTM). The kinetic was faster for Si/Mg-doped carbon adsorbent, possibly due to different chemical features provoked by the doping process. The thermodynamic data showed that the adsorption of OME on biobased adsorbents was spontaneous and favorable at four studied temperatures (283, 293, 298, 303, 308, 313, and 318 K), with the magnitude of the adsorption correspondent to a physical adsorption process (ΔH° < 2 kJ mol-1). The adsorbents were applied to treat synthetic hospital effluents and exhibited a high percentage of removal (up to 62%). The results of this work show that the composite between spruce bark biomass and Si/Mg was an efficient adsorbent for OME removal. Therefore, this study can help open new strategies for developing sustainable and effective adsorbents to tackle water pollution.

RESUMO

The harmful effects on the environment caused by the indiscriminate use of synthetic plastics and the inadequate management of post-consumer waste have given rise to efforts to redirect this consumption to bio-based economic models. In this sense, using biopolymers to produce materials is a reality for food packaging companies searching for technologies that allow these materials to compete with those from synthetic sources. This review paper focused on the recent trends in multilayer films with the perspective of using biopolymers and natural additives for application in food packaging. Firstly, the recent developments in the area were presented concisely. Then, the main biopolymers used (gelatin, chitosan, zein, polylactic acid) and main methods for multilayer film preparation were discussed, including the layer-by-layer, casting, compression, extrusion, and electrospinning methods. Furthermore, we highlighted the bioactive compounds and how they are inserted in the multilayer systems to form active biopolymeric food packaging. Furthermore, the advantages and drawbacks of multilayer packaging development are also discussed. Finally, the main trends and challenges in using multilayer systems are presented. Therefore, this review aims to bring updated information in an innovative approach to current research on food packaging materials, focusing on sustainable resources such as biopolymers and natural additives. In addition, it proposes viable production routes for improving the market competitiveness of biopolymer materials against synthetic materials.

RESUMO

Sapelli wood sawdust-derived magnetic activated carbon (SWSMAC) was produced by single-step pyrolysis using KOH and NiCl2 as activating and magnetization agents. SWSMAC was characterized by several techniques (SEM/EDS, N2 adsorption/desorption isotherms, FTIR, XRD, VSM, and pHPZC) and applied in the brilliant blue FCF dye adsorption from an aqueous medium. The obtained SWSMAC was a mesoporous material and showed good textural properties. Metallic nanostructured Ni particles were observed. Also, SWSMAC exhibited ferromagnetic properties. In the adsorption experiments, adequate conditions were an adsorbent dosage of 0.75 g L-1 and a solution pH of 4. The adsorption was fast, and the pseudo-second-order demonstrated greater suitability to the kinetic data. The Sips model fitted the equilibrium data well, and the maximum adsorption capacity predicted by this model was 105.88 mg g-1 (at 55 °C). The thermodynamic study revealed that the adsorption was spontaneous, favorable, and endothermic. Besides, the mechanistic elucidation suggested that electrostatic interactions, hydrogen bonding, π-π interactions, and n-π interactions were involved in the brilliant blue FCF dye adsorption onto SWSMAC. In summary, an advanced adsorbent material was developed from waste by single-step pyrolysis, and this material effectively adsorbs brilliant blue FCF dye.

Assuntos

RESUMO

Water pollution by dyes has been a major environmental problem to be tackled, and magnetic adsorbents appear as promising alternatives to solve it. Herein, magnetic activated carbons were prepared by the single-step method from Sapelli wood sawdust, properly characterized, and applied as adsorbents for brilliant blue dye removal. In particular, two magnetic activated carbons, MAC1105 and MAC111, were prepared using the proportion of biomass KOH of 1:1 and varying the proportion of NiCl2 of 0.5 and 1. The characterization results demonstrated that the different proportions of NiCl2 mainly influenced the textural characteristics of the adsorbents. An increase in the surface area from 260.0 to 331.5 m2 g-1 and in the total pore volume from 0.075 to 0.095 cm3 g-1 was observed with the weight ratio of NiCl2. Both adsorbents exhibit ferromagnetic properties and the presence of nanostructured Ni particles. The different properties of the materials influenced the adsorption kinetics and equilibrium of brilliant blue dye. MAC111 showed faster kinetics, reaching the equilibrium in around 10 min, while for MAC1105, it took 60 min for the equilibrium to be reached. In addition, based on the Sips isotherm, the maximum adsorption capacity was 98.12 mg g-1 for MAC111, while for MAC1105, it was 60.73 mg g-1. Furthermore, MAC111 presented the potential to be reused in more adsorption cycles than MAC1105, and the use of the adsorbents in the treatment of a simulated effluent exhibited high effectiveness, with removal efficiencies of up to 90%.

Assuntos

RESUMO

The Calophyllum inophyllum species annually produces a large volume of cylindrical fruits, which accumulate on the soil because they do not have nutritional value. This study sought to enable the use of this biomass by producing activated biochar with zinc chloride as an activating agent for further application as an adsorbent in batch and fixed bed columns. Different methodologies were used to characterize the precursor and the pyrolyzed material. Morphological changes were observed with the emergence of new spaces. The carbonaceous material had a surface area of 468 m2 g-1, Dp = 2.7 nm, and VT = 3.155 × 10-1 cm3 g-1. Scientific and isothermal studies of the adsorption of the diuron were conducted at the natural pH of the solution and adsorbent dosage of 0.75 g L-1. The kinetic curves showed a good fit to the Avrami fractional order model, with equilibrium reached after 150 min, regardless of the diuron concentration. The Liu heterogeneous surface model well represented the isothermal curves. By raising the temperature, adsorption was encouraged, and at 318 K, the Liu Qmax was reached at 250.1 mg g-1. Based on the Liu equilibrium constant, the nonlinear van't Hoff equation was employed, and the ΔG° were < 0 from 298 to 328 K; the process was exothermic nature (ΔH0 = -46.40 kJ mol-1). Finally, the carbonaceous adsorbent showed good removal performance (63.45%) compared to a mixture containing different herbicides used to control weeds. The stoichiometric column capacity (qeq) was 13.30 and 16.61 mg g-1 for concentrations of 100 and 200 mg L-1, respectively. The length of the mass transfer zone was 5.326 cm (100 mg L-1) and 4.946 cm (200 mg L-1). This makes employing the leftover fruits of the Calophyllum inophyllum species as biomass for creating highly porous adsorbents a very effective and promising option.

Assuntos

RESUMO

This work proposes a facile methodology for producing porous biochar material (ABC) from açaí kernel residue, produced by chemical impregnation with ZnCl2 (1:1) and pyrolysis at 650.0 °C. The characterization was achieved using several techniques, and the biochar material was employed as an adsorbent to remove catechol. The results show that ABC carbon has hydrophilic properties. The specific surface area and total pore volume are 1315 m2·g−1 and 0.7038 cm3·g−1, respectively. FTIR revealed the presence of oxygenated groups, which can influence catechol adsorption. The TGA/DTG indicated that the sample is thermally stable even at 580 °C. Adsorption studies showed that equilibrium was achieved in <50 min and the Avrami kinetic model best fits the experimental data, while Freundlich was observed to be the best-fitted isotherm model. Catechol adsorption on ABC biochar is governed by van der Waals forces and microporous and mesoporous filling mechanisms. The Qmax is 339.5 mg·g−1 (40 °C) with 98.36% removal of simulated effluent, showing that açaí kernel is excellent biomass to prepare good biochar that can be efficiently used to treat real industrial effluents.

Assuntos

RESUMO

Rare earth elements such as neodymium (Nd) are important elements used mainly in developing new technologies. Although they are found in low concentrations in nature, they can be obtained by extracting solid samples such as phosphogypsum. Among the techniques, adsorption has been used successfully with several adsorbent materials. In this work, two strains of Spirulina platensis (LEB-18 and LEB-52) were employed as biosorbents for efficiently removing the Nd element from the aqueous media. Biosorption tests were carried out in a batch system, and the results of the biosorption kinetics showed that for both materials, the biosorption of Nd was better described by the Avrami model. Moreover, it could be considered that 80 min would be necessary to attain the equilibrium of Nd(III) using both biosorbents. The result of the biosorption isotherms showed that for both strains, the best-fitted model was the Liu model, having a maximum biosorption capacity of 72.5 mg g−1 for LEB-18 and 48.2 mg g−1 for LEB-52 at a temperature of 298 K. Thermodynamics of adsorption showed that for both LEB-18 and LEB-52 the process was favorable (∆G° < 0) and exothermic (∆H° −23.2 for LEB-18 and ∆H° −19.9 for LEB-52). Finally, both strains were suitable to uptake Nd, and the better result of LEB-18 could be attributed to the high amount of P and S groups in this biomass. Based on the results, a mechanism of electrostatic attraction of Nd3+ and phosphate and sulfate groups of both strains of Spirulina platensis was proposed.

RESUMO

A biomass amino silica-functionalized material was successfully prepared by a simple sol-gel method. 3-Aminopropyltriethoxysilane (APTES) was added to a tannin-rich grape residue to improve its physicochemical properties and enhance the adsorption performance. The APTES functionalization led to significant changes in the material's characteristics. The functionalized material was efficiently applied in the removal of methyl orange (MO) due to its unique characteristics, such as an abundance of functional groups on its surface. The adsorption process suggests that the electrostatic interactions were the main acting mechanism of the MO dye removal, although other interactions can also take place. The functionalized biomass achieved a very high MO dye maximum adsorption capacity (Q max) of 361.8 mg g-1. The temperature positively affected the MO removal, and the thermodynamic studies indicated that the adsorption of MO onto APTES-functionalized biomass was spontaneous and endothermic, and enthalpy is driven in the physisorption mode. The regeneration performance revealed that the APTES-functionalized biomass material could be easily recycled and reused by maintaining very good performance even after five cycles. The adsorbent material was also employed to treat two simulated dye house effluents, which showed 48% removal. At last, the APTES biomass-based material may find significant applications as a multifunctional adsorbent and can be used further to separate pollutants from wastewater.

RESUMO

Two carbon composite materials were prepared by mixing avocado biochar and methyl polysiloxane (MK). Firstly, MK was dissolved in ethanol, and then the biochar was added at different times. In sample 1 (R1), the time of adding biochar was immediately after dissolving MK in ethanol, and in sample 2 (R2), after 48 h of MK dissolved in ethanol. The samples were characterized by nitrogen adsorption/desorption measurements obtaining specific surface areas (SBET) of 115 m2 g-1 (R1) and 580 m2 g-1 (R2). The adsorbents were further characterized using scanning electron microscopy, FTIR and Raman spectroscopy, adsorption of vapors of n-heptane and water, thermal analysis, Bohem titration, pHpzc, and C H N elemental analysis. R1 and R2 adsorbents were employed as adsorbents to remove the antibiotic ciprofloxacin from the waters. The t1/2 and t0.95 based on the interpolation of Avrami fractional-order were 20.52 and 246.4 min (R1) and 14.00 and 157.6 min (R2), respectively. Maximum adsorption capacities (Qmax) based on the Liu isotherm were 10.77 (R1) and 63.80 mg g-1 (R2) for ciprofloxacin. The thermodynamic studies showed a spontaneous and exothermic process for both samples, and the value of ΔH° is compatible with physical adsorption.

Assuntos

RESUMO

A new alternative aerogel was prepared from low-cost chitin and psyllium biopolymers to adsorb crystal violet (CV) dye from liquid media and possibly treat effluents containing other dyes. The aerogel was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM), which demonstrated that aerogel has a typical structure of amorphous materials and presented a randomly interconnected porous structure that resembles an open pore network. 2.5 g L-1 of aerogel was able to remove 86.00% of CV from solutions, and the natural pH of the CV solution was considered the more adequate for adsorption. The pseudo-second-order (PSO) model satisfactorily described the adsorption kinetics, and the Freundlich model was suitable to represent the adsorption equilibrium. The maximum experimental capacity achieved was 227.11 mg g-1, which indicates that aerogel is very efficient and competitive with several adsorbents. Tests using a simulated effluent showed that aerogel has excellent potential to treat real colored effluents.

Assuntos

RESUMO

This paper presents the synthesis of a hybrid material through the use of natural pozzolan and titanium(IV) isopropoxide using the sol-gel method and its application in the photocatalytic hexavalent chromium reduction. The characterization data indicated a mesoporous material possessing a surface area of 271.7 m2 g-1. The morphology studies (SEM and TEM) showed nanosheet hybrid structures. The analysis of DRUV, FTIR, XRD, and Mössbauer spectroscopy provides a different electronic structure of the synthetized material when compared with the originals, proving the hybridization process between pozzolan and titanium(IV) isopropoxide. The photocatalytic reduction of Cr(VI) to Cr(III) using the hybrid material showed a better performance than conventional photocatalysts (precursor and TiO2-P25). Operational conditions such as chromium initial concentration (0.02-0.20 mM), solution pH (3-6), and type of scavenger (citric or tartaric acid) were evaluated in order to determine the best experimental conditions for the Cr(VI) photoreduction. At their optimum (catalyst load of 15 mg L-1, tartaric acid as scavenger, [scavenger]0/[Cr(VI)]0 M ratio = 3:1, pH 3, and 25 °C), the total photoreduction of 0.20 mM Cr(VI) was achieved in 180 min. The novel hybrid materials synthesized from pozzolan and titanium(IV) isopropoxide showed to be a potential catalyst for the Cr(VI) reduction in aqueous solution. Graphical abstract.

Assuntos

RESUMO

This review discusses the imminent threat that microplastics (MPs) associated with pharmaceuticals represent to the aquatic environment and public health. We initially focused upon recognizing and stressing that MPs are ubiquitous pollutants. The influence of environmental factors, such as pH, mechanical stress, and photodegradation, are examined, aiming to elucidate how both substances might associate, what are their simultaneous degradation pathways and, to understand the interactions between MPs and pharmaceuticals. Mathematical tools, such as modeling and simulations, are presented in detail, aiming to improve how information is interpreted. Furthermore, it is exhibited that MPs sorption and interaction behavior towards organic contaminants play an important role in understanding its dynamics in the environment, as well as their possible interactions with pharmaceuticals that are summarized. At last, MPs and pharmaceuticals toxicity and bioaccumulation are presented.

Assuntos

RESUMO

This study presents the extraction of antibiotic amoxicillin (AMX) from aqueous solution employing activated carbons (AC) from olive biomass (OB). Two AC were prepared using ZnCl2 (activator agent), and a conventional muffle furnace (ACF) or microwave oven (ACMW). The structure, morphology, and textural properties from both AC were analyzed by scanning electron microscope (SEM), pH of point-zero-charge (pHPZC), infrared spectroscopy (FTIR), and N2 adsorption/desorption isotherms. AC with mesoporous structures rich in oxygenated groups and high specific area (as high as 1742 m2 g-1) were helpful for the efficient and fast adsorption of AMX. The Avrami kinetic nonlinear equation showed the best fitting for the empirical data when related to the pseudo-1st and pseudo-2nd order. The isothermal experimental data followed the Liu nonlinear model, displaying at 25 °C the maximum sorption capacity of 237.02 and 166.96 mg g-1 for the ACF and ACMW, respectively. An adsorption test with synthetic hospital effluent was carried out to evaluate the possibility of applying both adsorbents in wastewater purification. The purification efficiency was up to 94.4% and 91.96% for ACF and ACMW, respectively. Therefore, the AC obtained from OB (containing a mixture of seed, pulp, and olive peel) has a high potential for application in removing emerging contaminants from the wastewater.

Assuntos

RESUMO

Wastes from the Pacara Earpod tree (Enterolobium contortisilquum) and Ironwood (Caesalpinia leiostachya) seeds were studied as biosorbents for the removal of basic fuchsin from waters. Both biosorbents were prepared and characterized by different analytical methods. The characterization data showed that both materials were mainly composed of lignin, cellulose, and hemicellulose. Both biosorbents exhibited roughened surfaces and surface functional groups such as C-H, C=O, C=C, C-O, C-N, and OH bonds. Furthermore, the XRD pattern shows an amorphous phase with a wide peak from 10 to 30° due to the lignin. In terms of dosage and pH, the use of 1 g L-1 and 9.0, respectively, is recommended. The initial concentrations for the biosorption kinetics ranged from 50 to 500 mg L-1, where the Pacara ear and the Ironwood reached an adsorption capacity of 145.62 and 100.743 mg g-1 for the 500 mg L-1. The pseudo-second-order was found to be the proper model for describing biosorption of basic fuchsin onto Pacara Earpod tree and Ironwood, respectively. For the isotherm experiments, the maximum experimental biosorption capacity was found to be 166.858 and 110.317 mg g-1 for the Pacara Earpod and Ironwood for the initial concentration of 500 mg L-1 at 328 K. The Langmuir and the Tóth models were the best for representing the equilibrium curves for the basic fuchsin on the Pacara Earpod and the Ironwood, respectively. Maximum adsorption capacities of 177.084 mg g-1 and 136.526 mg g-1 were achieved for the Pacara Earpod tree and Ironwood, respectively. The biosorption process was spontaneous, endothermic, and favorable for both biosorbents. The biosorbents were also applied for coloration removal of simulated textile effluents, reaching 66% and 54% for the Pacara Earpod and Ironwood, respectively. For the final application, the materials were used in fixed-bed biosorption, with an initial concentration of 200 mg L-1, reaching breakthrough times of 710 and 415 min, leading to biosorption capacities of the column of 124.5 and 76.5 mg g-1, for the Pacara Earpod and Ironwood, respectively.

Assuntos

RESUMO

The present research describes the synthesis of new nanomagnetic activated carbon material with high magnetization, and high surface area prepared in a single pyrolysis step that is used for the carbonization, activation, and magnetization of the produced material. The pyrolysis step of tucumã seed was carried out in a conventional tubular oven at 600 °C under N2-flow. It was prepared three magnetic carbons MT-1.5, MT-2.0, MT-2.5, that corresponds to the proportion of biomass: ZnCl2 always 1:1 and varying the proportion of NiCl2 of 1.5, 2.0, and 2.5, respectively. These magnetic nanocomposites were characterized by Vibrating Sample Magnetometer (VSM), X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, hydrophobic/hydrophilic balance, CHN/O elemental analysis, modified Boehm titration, N2 adsorption-desorption isotherms; and pHpzc. All the materials obtained presented Ni particles with an average crystallite size of less than 33 nm. The MT-2.0 was employed for the removal of nicotinamide and propranolol from aqueous solutions. Based on Liu isotherm, the Qmax was 199.3 and 335.4 mg g-1 for nicotinamide and propranolol, respectively. MT-2.0 was used to treat simulated pharmaceutical industry effluents attaining removal of all organic compounds attaining up to 99.1 % of removal.

Assuntos