RESUMO
A indicação das soluções anestésicas nos tratamentos endodônticos de rotina deve estar fundamentada nos conhecimentos dos possíveis efeitos que essas substâncias podem desencadear no paciente sistemicamente comprometido. Objetivo: O objetivo do presente estudo foi priorizar a indicação e discutir os possíveis efeitos secundários ou adversos passíveis de ocorrência com as substâncias que compõem as soluções anestésicas durante a rotina de tratamento dos canais radiculares (AU).
The indication of anesthetic solutions in routine endodontic treatments must be based on knowledge of the possible effects that these substances can trigger in systemically compromised patients. Aim: The aim of the present study was to prioritize the indication and discuss the possible secondary or adverse effects likely to occur with the use of substances of which anesthetic solutions are composed, during the routine treatment of root canals (AU).
Assuntos
Humanos , Tratamento do Canal Radicular , Anestésicos , Soluções/efeitos adversosRESUMO
The aim of this study was to evaluate the effect of peracetic acid (PAA) as a single irrigant on the smear layer, on the intraradicular dentinal bond strength, and on the penetrability of an epoxy-based resin sealer into the dentinal tubules. A total of 120 roots were distributed into 4 groups according to the irrigant used in root canal preparation: 1% PAA (PAA); 2.5% NaOCl followed by final irrigation with 17% EDTA and 2.5% NaOCl (NaOCl-EDTA-NaOCl); 2.5% NaOCl (NaOCl); and saline solution (SS). The smear layer was evaluated using scanning electron microscopy. The bond strength of an epoxy-based resin sealer (AH Plus) to root dentin was evaluated by the push-out test and penetrability of the sealer into dentinal tubules was observed by confocal laser microscopy. The results were analyzed by the Kruskal-Wallis and the Dunn post-test (α = 0.05). The use of 1% PAA as single root canal irrigant provided smear layer removal and improved the penetrability and bond strength of AH Plus to root dentin in a manner similar to that of the NaOCl-EDTA-NaOCl group (p > 0.05). The NaOCl and SS groups had higher values of smear layer and lower values of sealer penetrability and dentin bond strength than the PAA and NaOCl-EDTA-NaOCl groups (p < 0.05). Thus, 1% PAA has the potential to be used as a single irrigant in root canals.
Assuntos
Cavidade Pulpar/efeitos dos fármacos , Dentina/efeitos dos fármacos , Resinas Epóxi/química , Ácido Peracético/química , Materiais Restauradores do Canal Radicular/química , Irrigantes do Canal Radicular/química , Camada de Esfregaço/química , Colagem Dentária/métodos , Cavidade Pulpar/química , Dentina/química , Ácido Edético/química , Humanos , Teste de Materiais , Microscopia Confocal , Microscopia Eletrônica de Varredura , Valores de Referência , Reprodutibilidade dos Testes , Hipoclorito de Sódio/químicaRESUMO
STATEMENT OF PROBLEM: The post space must be irrigated with solutions that do not interfere with the bond strength and enhance penetration into the dentinal tubules of self-etching resin cement. Which solution is best is unclear. Peracetic acid with different formulations appears to be a good option. PURPOSE: The purpose of this in vitro study was to evaluate the effect of irrigating the fiber post space by using 1% peracetic acid (PA) at low (LH) or high (HH) hydrogen peroxide concentration on the bond strength and penetration into the dentinal tubules of RelyX U200 self-etching resin cement. MATERIAL AND METHODS: After intraroot preparation for fiber posts in 60 endodontically treated teeth, the specimens were divided into 4 groups (n=15) according to the irrigation protocol: CG (control), distilled water; NA (NaOCl), 2.5% sodium hypochlorite; LHPA, PA with a low concentration of hydrogen peroxide; and HHPA, PA with a high concentration of hydrogen peroxide. The fiber posts were then cemented with self-etching resin cement labeled with rhodamine. Cross sections of the thirds were obtained by confocal scanning microscopy and submitted to the push-out and cement penetration tests. The data obtained in the push-out tests were evaluated by using ANOVA and the Tukey post hoc test, and those data obtained in the confocal screening were evaluated by using the Kruskal-Wallis and Dunn (Bonferroni correction) tests (α=.05). RESULTS: Bond strength values in the cervical third of the CG were higher than those in NA (P=.035) but similar to those of the other groups (P=.05). In the other thirds, CG and LHPA values were similar to one another (P=.05) but higher than those of NA and HHPA (P<.001). The penetration rate assessed by confocal scanning microscopy revealed similar results in the cervical third for all groups (P=.075), except for NA which provided the lowest penetration. In the remaining thirds, CG and LHPA provided the highest penetration rate (P=.015). CONCLUSIONS: The LHPA group had no negative effects on the bond strength and penetration into the dentinal tubules of the self-etching resin cement.
Assuntos
Colagem Dentária , Técnica para Retentor Intrarradicular , Dentina , Ácido Peracético , Cimentos de ResinaRESUMO
Abstract The aim of this study was to evaluate the effect of peracetic acid (PAA) as a single irrigant on the smear layer, on the intraradicular dentinal bond strength, and on the penetrability of an epoxy-based resin sealer into the dentinal tubules. A total of 120 roots were distributed into 4 groups according to the irrigant used in root canal preparation: 1% PAA (PAA); 2.5% NaOCl followed by final irrigation with 17% EDTA and 2.5% NaOCl (NaOCl-EDTA-NaOCl); 2.5% NaOCl (NaOCl); and saline solution (SS). The smear layer was evaluated using scanning electron microscopy. The bond strength of an epoxy-based resin sealer (AH Plus) to root dentin was evaluated by the push-out test and penetrability of the sealer into dentinal tubules was observed by confocal laser microscopy. The results were analyzed by the Kruskal-Wallis and the Dunn post-test (α = 0.05). The use of 1% PAA as single root canal irrigant provided smear layer removal and improved the penetrability and bond strength of AH Plus to root dentin in a manner similar to that of the NaOCl-EDTA-NaOCl group (p > 0.05). The NaOCl and SS groups had higher values of smear layer and lower values of sealer penetrability and dentin bond strength than the PAA and NaOCl-EDTA-NaOCl groups (p < 0.05). Thus, 1% PAA has the potential to be used as a single irrigant in root canals.
Assuntos
Humanos , Ácido Peracético/química , Materiais Restauradores do Canal Radicular/química , Irrigantes do Canal Radicular/química , Camada de Esfregaço/química , Cavidade Pulpar/efeitos dos fármacos , Dentina/efeitos dos fármacos , Resinas Epóxi/química , Valores de Referência , Hipoclorito de Sódio/química , Teste de Materiais , Microscopia Eletrônica de Varredura , Reprodutibilidade dos Testes , Colagem Dentária/métodos , Ácido Edético/química , Microscopia Confocal , Cavidade Pulpar/química , Dentina/químicaRESUMO
Objetivo: Avaliar o efeito da dentina sobre o pH e a atividade antimicrobiana de formulações com hidróxido de cálcio. Material e método: O pH e a atividade antimicrobiana das formulações (G1- polietilenoglicol, G2- glicerina e paramonoclorofenol canforado ou G3- clorexidina) foram analisados nas formulações puras (G1A, G2A e G3A) ou acrescidas de dentina em pó (G1B, G2B e G3B). Tubos de polietileno foram preenchidos com uma das formulações e imersos em água destilada. O pH foi analisado após 24 horas, 7, 14 e 21 dias. A atividade antimicrobiana foi avaliada sobre Enterococcus faecalis (ATCC 29212), através do teste de difusão em ágar. Os resultados foram submetidos aos testes de ANOVA e Tukey (p=0,05). Resultado: A dentina não exerceu efeito sobre o pH das formulações, exceto ocasionando a redução em G1, no período de 24 horas (p<0,05). Nas demais formulações, não houve interferência da dentina sobre o pH (p>0,05). Quando comparados entre os grupos, em 24 horas e 7 dias, G1A e G1B apresentaram menor pH (p<0,05). Em 14 dias, G2A, G2B, G3A e G3B demonstraram similar pH (p>0,05), assim como entre G3B e G1A (p>0,05). Em 21 dias, todas as formulações demonstram semelhante pH (p>0,05). Os resultados em ordem decrescente da atividade antimicrobiana foram G2A=G2B>G3A=G3B>G1A=G1B (p<0,05). Conclusão: A dentina não interferiu no pH e na atividade antimicrobiana das diferentes formulações com hidróxido de cálcio, exceto na associação com o polietilenoglicol, em que ocasionou a redução do pH apenas no período de 24 horas. A formulação com paramonoclorofenol canforado apresentou maior atividade antimicrobiana, seguida da clorexidina e do polietilenoglicol. .
Objective: To evaluate the dentin effect on pH and antimicrobial activity of the calcium hydroxide chemical formulations. Material and method: pH and antimicrobial activity of calcium hydroxide formulations were evaluated (G1-polyethyleneglycol, G2-glycerin and camphorated paramonochlorophenol and G3-chlorhexidine). The formulations were evaluated alone (G1A, G2A e G3A) or with dentin powder (G1B, G2B and G3B). Polyethylene tubes were filled with the formulation and immersed in distilled water. After 24 hours, 7, 14 and 21 days, pH was evaluated. The antimicrobial activity was evaluated against Enterococcus faecalis by agar diffusion test. All data were submitted to ANOVA and Tukey tests (p=0.05). Result: None effect was observed on pH and antimicrobial activity by dentin on different chemical formulations, except the reduction occurred in G1 at 24 hours (p <0.05). When compared between the groups at 24 hours and 7 days, G1A and G1B had a lower pH (p <0.05). At 14 days, G2A, G2B, G3A and G3B showed similar pH (p<0.05) and between G3B and G1A (p>0.05). At 21 days, all formulations were similar (p>0.05). Regarding antimicrobial activity G2B G2A => = G3A G3B> = G1A G1B (p<0.05). Conclusion: The dentin did not affect the pH and antimicrobial activity of different formulations containing calcium hydroxide, except in association with polyethylene glycol, which caused the reduction of pH, within 24 hours. The formulation with paramonochlorophenol camphor showed higher antimicrobial activity, followed by chlorhexidine and polyethylene glycol. .
Assuntos
Hidróxido de Cálcio , Análise de Variância , Enterococcus faecalis , Dentina , Concentração de Íons de Hidrogênio , Clorexidina , EndodontiaRESUMO
The objective of this study was to describe the main lesions that simulate clinically and propose a treatment protocol for acute endodontic infection. Signs and clinical symptoms of periodontal abscess, gingival abscess, odontoma, herpes simplex, pericoronitis, acute pulpitis and necrotizing ulcerative gingivitis/periodontitis (NUG/NUP) were described and compared with acute endodontic infections. A treatment protocol was described by optimizing the procedures in access cavity, microbial decontamination and detoxification of the root canal, apical debridement, intracanal and systemic medication and surgical drainage procedures. The convenience of the use of 5.25% sodium hypochlorite, root canal instrumentation using a crown-down technique, intracanal medication with 2% chlorhexidine or triple antibiotic paste and the convenience of the use of antibiotics, analgesics, and surgical drainage to solve cases of acute dentoalveolar abscess was discussed.
Assuntos
Cavidade Pulpar , Abscesso Periapical/diagnóstico , Periodontite Periapical/diagnóstico , Diagnóstico Diferencial , Humanos , Abscesso Periapical/terapia , Periodontite Periapical/tratamento farmacológico , Irrigantes do Canal Radicular/uso terapêutico , Preparo de Canal Radicular , Tratamento do Canal RadicularRESUMO
AIM: The aim of this study was to evaluate the fracture resistance of teeth submitted to several internal bleaching protocols using 35% hydrogen peroxide (35HP), 37% carbamide peroxide (37CP), 15% hydrogen peroxide with titanium dioxide nanoparticles (15HPTiO2) photoactivated by LED-laser or sodium perborate (SP). MATERIALS AND METHODS: After endodontic treatment, fifty bovine extracted teeth were divided into five groups (n = 10): G1-unbleached; G2-35HP; G3-37CP; G4-15HPTiO2 photoactivated by LED-laser and G5-SP. In the G2 and G4, the bleaching protocol was applied in 4 sessions, with 7 days intervals between each session. In the G3 and G5, the materials were kept in the pulp teeth for 21 days, but replaced every 7 days. After 21 days, the teeth were subjected to compressive load at a cross head speed of 0.5 mm/min, applied at 135° to the long axis of the root using an eletromechanical testing machine, until teeth fracture. The data were submitted to ANOVA and Tukey tests (α = 5%). RESULTS: The 35HP, 37CP, 15HPTiO2 and SP showed similar fracture resistance teeth reduction (p > 0.05). All bleaching treatments reduced the fracture resistance compared to unbleached teeth (p < 0.05). CONCLUSION: All bleaching protocols reduced the fracture resistance of endodontically-treated teeth, but there were no differences between each other. CLINICAL SIGNIFICANCE: There are several internal bleaching protocols using hydrogen peroxide in different concentrations and activation methods. This study evaluated its effects on fracture resistance in endodontically-treated teeth.
Assuntos
Cavidade Pulpar/efeitos dos fármacos , Clareadores Dentários/uso terapêutico , Clareamento Dental/métodos , Fraturas dos Dentes/fisiopatologia , Animais , Boratos/uso terapêutico , Peróxido de Carbamida , Bovinos , Análise do Estresse Dentário/instrumentação , Peróxido de Hidrogênio/uso terapêutico , Terapia com Luz de Baixa Intensidade , Teste de Materiais , Nanopartículas , Peróxidos/uso terapêutico , Fármacos Fotossensibilizantes/uso terapêutico , Distribuição Aleatória , Tratamento do Canal Radicular/métodos , Estresse Mecânico , Fatores de Tempo , Titânio/uso terapêutico , Ureia/análogos & derivados , Ureia/uso terapêuticoRESUMO
UNLABELLED: Recently, various calcium silicate-based sealers have been introduced for use in root canal filling. The MTA Fillapex is one of these sealers, but some of its physicochemical properties are not in accordance with the ISO requirements. OBJECTIVE: The aim of this study was to evaluate the flowability, pH level and calcium release of pure MTA Fillapex (MTAF) or containing 5% (MTAF5) or 10% (MTAF10) calcium hydroxide (CH), in weight, in comparison with AH Plus sealer. MATERIAL AND METHODS: The flowability test was performed according to the ISO 6876:2001 requirements. For the pH level and calcium ion release analyses, the sealers were placed individually (n=10) in plastic tubes and immersed in deionized water. After 24 hours, 7 and 14 days, the water in which each specimen had been immersed was evaluated to determine the pH level changes and calcium released. Flowability, pH level and calcium release data were analyzed statistically by the ANOVA test (α=5%). RESULTS: In relation to flowability: MTAF>AH Plus>MTAF5>MTAF10. In relation to the pH level, for 24 h: MTAF5=MTAF10=MTAF>AH Plus; for 7 and 14 days: MTAF5=MTAF10>MTAF>AH Plus. For the calcium release, for all periods: MTAF>MTAF5=MTAF10>AH Plus. CONCLUSIONS: The addition of 5% CH to the MTA Fillapex (in weight) is an alternative to reduce the high flowability presented by the sealer, without interfering in its alkalization potential.
Assuntos
Compostos de Alumínio/química , Compostos de Cálcio/química , Hidróxido de Cálcio/química , Cálcio/química , Resinas Epóxi/química , Óxidos/química , Materiais Restauradores do Canal Radicular/química , Silicatos/química , Análise de Variância , Combinação de Medicamentos , Teste de Materiais , Valores de Referência , Fatores de Tempo , Viscosidade , Água/químicaRESUMO
Recently, various calcium silicate-based sealers have been introduced for use in root canal filling. The MTA Fillapex is one of these sealers, but some of its physicochemical properties are not in accordance with the ISO requirements. Objective: The aim of this study was to evaluate the flowability, pH level and calcium release of pure MTA Fillapex (MTAF) or containing 5% (MTAF5) or 10% (MTAF10) calcium hydroxide (CH), in weight, in comparison with AH Plus sealer. Material and Methods: The flowability test was performed according to the ISO 6876:2001 requirements. For the pH level and calcium ion release analyses, the sealers were placed individually (n=10) in plastic tubes and immersed in deionized water. After 24 hours, 7 and 14 days, the water in which each specimen had been immersed was evaluated to determine the pH level changes and calcium released. Flowability, pH level and calcium release data were analyzed statistically by the ANOVA test (α=5%). Results: In relation to flowability: MTAF>AH Plus>MTAF5>MTAF10. In relation to the pH level, for 24 h: MTAF5=MTAF10=MTAF>AH Plus; for 7 and 14 days: MTAF5=MTAF10>MTAF>AH Plus. For the calcium release, for all periods: MTAF>MTAF5=MTAF10>AH Plus. Conclusions: The addition of 5% CH to the MTA Fillapex (in weight) is an alternative to reduce the high flowability presented by the sealer, without interfering in its alkalization potential. .
Assuntos
Compostos de Alumínio/química , Compostos de Cálcio/química , Hidróxido de Cálcio/química , Cálcio/química , Resinas Epóxi/química , Óxidos/química , Materiais Restauradores do Canal Radicular/química , Silicatos/química , Análise de Variância , Combinação de Medicamentos , Teste de Materiais , Valores de Referência , Fatores de Tempo , Viscosidade , Água/químicaRESUMO
Due to the low radiopacity of Sealer 26, iodoform is frequently empirically added to this sealer. Thus, the interference of this procedure with the physicochemical properties of Sealer 26 must be evaluated. Objective: This study evaluated the influence of the addition of iodoform on setting time, flow, solubility, pH, and calcium release of an epoxy-based sealer. Material and Methods: The control group was pure Sealer 26, and the experimental groups were Sealer 26 added with 1.1 g, 0.55 g or 0.275 g of iodoform. Setting time evaluation was performed in accordance with the ASTM C266-03 speciflcation. The analysis of flow and solubility was in accordance with the ISO 6876-2001 speciflcation. For the evaluation of pH and calcium ion release, polyethylene tubes were filled with the materials and immersed in flasks with 10 ml of deionized water. After 24 h, 7, 14, 21, 28, and 45 days pH was measured. In 45 days, the calcium released was evaluated with an atomic absorption spectrophotometer. Results: The addition of iodoform increased setting time in comparison with pure sealer (P<0.05). As for flow, solubility, and calcium release, the mixtures presented results similar to pure sealer (p>0.05). In the 24 h period, the mixture with 1.1 g and 0.55 g of iodoform showed lower pH than pure sealer and than sealer added with 0.275 g of iodoform (P<0.05). Conclusions: The iodoform added to Sealer 26 interferes with its setting time and solubility properties. Further studies are needed to address the clinical signiflcance of this interference. .
Assuntos
Bismuto/química , Hidróxido de Cálcio/química , Resinas Epóxi/química , Hidrocarbonetos Iodados/química , Materiais Restauradores do Canal Radicular/química , Análise de Variância , Concentração de Íons de Hidrogênio , Teste de Materiais , Fenômenos Químicos , Valores de Referência , Reprodutibilidade dos Testes , Solubilidade , Fatores de TempoRESUMO
UNLABELLED: Due to the low radiopacity of Sealer 26, iodoform is frequently empirically added to this sealer. Thus, the interference of this procedure with the physicochemical properties of Sealer 26 must be evaluated. OBJECTIVE: This study evaluated the influence of the addition of iodoform on setting time, flow, solubility, pH, and calcium release of an epoxy-based sealer. MATERIAL AND METHODS: The control group was pure Sealer 26, and the experimental groups were Sealer 26 added with 1.1 g, 0.55 g or 0.275 g of iodoform. Setting time evaluation was performed in accordance with the ASTM C266-03 speciflcation. The analysis of flow and solubility was in accordance with the ISO 6876-2001 speciflcation. For the evaluation of pH and calcium ion release, polyethylene tubes were filled with the materials and immersed in flasks with 10 ml of deionized water. After 24 h, 7, 14, 21, 28, and 45 days pH was measured. In 45 days, the calcium released was evaluated with an atomic absorption spectrophotometer. RESULTS: The addition of iodoform increased setting time in comparison with pure sealer (P<0.05). As for flow, solubility, and calcium release, the mixtures presented results similar to pure sealer (p>0.05). In the 24 h period, the mixture with 1.1 g and 0.55 g of iodoform showed lower pH than pure sealer and than sealer added with 0.275 g of iodoform (P<0.05). CONCLUSIONS: The iodoform added to Sealer 26 interferes with its setting time and solubility properties. Further studies are needed to address the clinical signiflcance of this interference.
Assuntos
Bismuto/química , Hidróxido de Cálcio/química , Resinas Epóxi/química , Hidrocarbonetos Iodados/química , Materiais Restauradores do Canal Radicular/química , Análise de Variância , Fenômenos Químicos , Concentração de Íons de Hidrogênio , Teste de Materiais , Valores de Referência , Reprodutibilidade dos Testes , Solubilidade , Fatores de TempoRESUMO
AIM: This clinical report presents a new method for retrieving separated instruments from the root canal with minimally invasive procedures. BACKGROUND: The presence of separated instrument in root canal may interfere in the endodontic treatment prognosis. There are several recommended methods to retrieve separated instruments, but some are difficult in clinically practice. CASE REPORT: This study describes two cases of separated instrument removal from the root canal using a stainless-steel prepared needle associated with a K-file. Case 1 presented a fractured gutta-percha condenser within the mandibular second premolar, it was separated during incorrect intracanal medication calcium hydroxide placement. Case 2 had a fractured sewing needle within the upper central incisor that the patient used to remove food debris from the root canal. After cervical preparation, the fractured instruments were fitted inside a prepared needle and then an endodontic instrument (#25 K-file) was adapted with clockwise turning motion between the needle inner wall and the fragment. CONCLUSION: The endodontic or atypical nonendodontic separated instrument may be easily pull on of the root canal using a single and low cost device. CLINICAL SIGNIFICANCE: The methods for retrieving separated instruments from root canal are difficult and destructive procedures. The present case describes a simple method to solve this problem.
Assuntos
Cavidade Pulpar/patologia , Corpos Estranhos/terapia , Preparo de Canal Radicular/instrumentação , Hidróxido de Cálcio/administração & dosagem , Criança , Falha de Equipamento , Humanos , Masculino , Pessoa de Meia-Idade , Agulhas , Retratamento , Irrigantes do Canal Radicular/administração & dosagem , Aço Inoxidável/químicaRESUMO
Avaliar os efeitos da incorporação do iodofórmio ou do hidróxido de cál-cio (HC) respectivamente no cimento Sealer 26 ou MTA Fillapex (MF). Na ava-liação com o Sealer 26, as proporções de 1.1g, 0,55g or 0.275g foram incorpo-radas ao cimento e o de tempo de presa, escoamento, solubilidade, pH e libe-ração de cálcio foram avaliados. Na análise do MF puro, acrescido de 5% (MF5) ou 10%(MF10) em massa de HC, o escoamento, pH e liberação de cál-cio foram comparados com AH Plus. A adição do iodofórmio ao Sealer26 au-mentou o tempo de presa do cimento (p<0,05), mas os demais resultados fo-ram similares (p>0,05). Em 24hs, a mistura com 1.1g: 0.55g de iodofórmio de-monstrou menor pH que o cimento puro (p<0,05). O MF teve maior escoamento que os demais cimentos (p<0,05). O MF10 apresentou menor escoamento que MF (P<0,05). O MF10 apresentou maior pH que o AH Plus (p<0,05).A liberação de cálcio foi similar ao MF e o MF10 (p>0,05). O MF5 demonstrou menor esco-amento que o MF e maior que MF10 (p<0,05), tendo maior valor de pH que o MF (p<0,05) e similar liberação de cácio ao MF10. A adição do iodofórmio inter-fere no tempo de presa e solubilidade do Sealer 26 e a adição de 5%HC no MF apresentou-se como alternativa para reduzir o escoamento, sem interferir no potencial de alcalinização do MF.
To evaluate the effects of incorporation of iodoform or calcium hydroxide (CH) respectively in cement Sealer 26 or MTA Fillapex (MF) . In review with the Sealer26, the proportions of 1.1g, 0.55g or 0.275g were incorporated into the cement and the setting time, flow, solubility, pH and calcium release were evaluated. The analysis of pure MTA Fillapex (MF) or containing 5% (MF5) or 10% (MF 10) calcium hydroxide (CH), in weight, in comparison with AH Plus sealer .The addition of iodoform to Sealer26 cement increased setting time(p < 0.05), but the other results were similar (p> 0.05). In 24 hours, the mixture with 1.1g : 0.55g iodoform showed lower pH than the pure cement ( p < 0.05 ) . The MF had greater flow than the other cements ( p < 0.05 ) . The MF10 showed lower flow that MF ( P < 0.05 ) . The MF10 showed pH greater than AH Plus (p< 0.05). Calcium realise was similar to MF and MF10 (p> 0.05). The MF5 showed less than the flow MF , and greater than MF10 (p <0.05 ), and higher pH value than the MF (p <0.05) and calcium release similar to MF10 . The addition of iodoform interferes with the setting time and solubility of Sealer 26 and the addition of 5% CH in the MF presented as an alternative to reduce the flow without interfering with potential alkalization
Assuntos
Cálcio , Cimentos Dentários , Fenômenos Químicos , EndodontiaRESUMO
Introduction: Endodontic sealer residues on dentinal surface have negative effects on adhesion of adhesives system and/or can cause discoloration of the dental crown. Objective: To evaluate the efficacy of 95% ethanol in removal of residues of epoxy-based (AH Plus), methacrylate-based (Epiphany SE) or calcium-based (Sealapex) sealers on dentinal surface. Material and methods: Thirty-two bovine incisor dental crown fragments (0.5 mm x 0.5 mm) were treated with 17% EDTA and 2.5% NaOCl. The specimens were divided into three experimental groups (n = 10): G1 (AH Plus), G2 (Epiphany SE) and G3 (Sealapex). In each group was applied a coating of one endodontic sealer type and were left undisturbed for 5 minutes. After this period, the specimens were cleaned with 95% ethanol. The control group was composed by two specimens that did not receive any sealer or cleaning treatment. The sealer residues persistence after cleaning with 95% ethanol was evaluated by scanning electron microscopy (x500) and a score system was applied. Data obtained were analyzed by Kruskal-Wallis and Dunn tests (α = 5%). Results: Moderate amount of endodontic sealer residues were observed in all groups, regardless of the endodontic sealer compositions. G1, G2 and G3 presented similar amount of sealer residues on dentinal surface after cleaning with 95% ethanol (p > 0.05). Conclusion: 95% ethanol was inefficiency to remove completely AH Plus, Epiphany SE and Sealapex residues of sealer-contaminated dentin.
RESUMO
AIM: This study investigated the flowability, setting time, pH, calcium release and bond strength of a MTA-based cement (MTA Fillapex(®)) compared to AH Plus and Sealapex. MATERIALS AND METHODS: For the flowability test, the ISO 6876:2001 specification was utilized and for the setting time test, the ASTM C266-03 specification was utilized. For the pH and calcium release measurements, 10 samples were prepared for each group and analyzed for several different periods. For the push-out test, dentin disks were distributed into three groups, according to the cement utilized and into three subgroups, according to the root third (n = 10). After obturation, the specimens underwent push-out testing. The data were compared statistically using a significance level of 5%. RESULTS: The flowability of all materials was found to be similar (p > 0.05). The setting times were different among the groups tested (MTA Fillapex < Sealapex < AH Plus) (p < 0.05). At days 7 and 28, the MTA Fillapex presented the higher pH values (p < 0.05). At 24 hours and at 14 days, the calcium release of the MTA Fillapex was similar to that of Sealapex (p > 0.05). AH Plus presented the lowest pH and calcium release values (p < 0.05). In all root thirds, the adhesion to the dentin of the MTA Fillapex and Sealapex were significantly lower than that of AH Plus (p < 0.05). CONCLUSION: MTA Fillapex and Sealapex presented several similar properties and both were found to be different than AH Plus. CLINICAL SIGNIFICANCE: This study evaluated the physicochemical and mechanical properties of new MTA-based root canal cement, in order to use this scaler in root canal fillings. MTA Fillapex showed satisfactory properties for clinical use.
Assuntos
Compostos de Alumínio/química , Compostos de Cálcio/química , Colagem Dentária , Óxidos/química , Materiais Restauradores do Canal Radicular/química , Silicatos/química , Adesividade , Cálcio/química , Hidróxido de Cálcio/química , Fenômenos Químicos , Cavidade Pulpar/ultraestrutura , Análise do Estresse Dentário/instrumentação , Dentina/ultraestrutura , Combinação de Medicamentos , Resinas Epóxi/química , Dureza , Humanos , Concentração de Íons de Hidrogênio , Teste de Materiais , Salicilatos/química , Estresse Mecânico , Fatores de Tempo , ViscosidadeRESUMO
The presence of residual endodontic sealer in the pulp chamber may cause discoloration of the dental crown and interfere with the adhesion of restorative materials. The aim of this study was to compare the efficacy of different solvents in removing residues of an epoxy resin-based sealer (AH Plus) from the dentin walls of the pulp chamber, by scanning electron microscopy (SEM). Forty-four bovine incisor dental crown fragments were treated with 17% EDTA and 2.5% NaOCl. Specimens received a coating of AH Plus and were left undisturbed for 5 min. Then, specimens were divided in four groups (n = 10) and cleaned with one of the following solutions: isopropyl alcohol, 95% ethanol, acetone solution, or amyl acetate solution. Negative controls (n = 2) did not receive AH Plus, while in positive controls (n = 2) the sealer was not removed. AH Plus removal was evaluated by SEM, and a score system was applied. Data were analyzed by Kruskal-Wallis and Dunn tests. None of the solutions tested was able to completely remove AH Plus from the dentin of the pulp chamber. Amyl acetate performed better than 95% ethanol and isopropyl alcohol (p < 0.05), but not better than acetone (p > 0.05) in removing the sealer from dentin. No significant differences were observed between acetone, 95% ethanol, and isopropyl alcohol (p > 0.05). It was concluded that amyl acetate and acetone may be good options for cleaning the pulp chamber after obturation with AH Plus.
Assuntos
Dentina/efeitos dos fármacos , Dentina/ultraestrutura , Resinas Epóxi/análise , Resinas Epóxi/metabolismo , Compostos Orgânicos/farmacologia , Materiais Restauradores do Canal Radicular/análise , Materiais Restauradores do Canal Radicular/metabolismo , Solventes/farmacologia , Animais , Bovinos , Processamento de Imagem Assistida por Computador , Incisivo/efeitos dos fármacos , Incisivo/ultraestrutura , Microscopia Eletrônica de Varredura , Compostos Orgânicos/metabolismo , Solventes/metabolismoRESUMO
The aim of this study was to evaluate the persistence of methacrylate-based cement residues on the dentin, after dentin surface cleaning with ethanol or acetone, with or without previous application of a dentin adhesive. Forty bovine crown fragments were obtained and the dentin surface was washed with 1.0 mL of 2.5% sodium hypochlorite (NaOCl), followed by 0.1 mL of 17% ethylenediaminetetraacetic acid application for 3 min, and final irrigation with 2.5% NaOCl. The specimens were air dried and resin-based cement was rubbed onto the dentine surface with a microbrush applicator. In 20 specimens, previously to cement, a dentin adhesive was applied in all surfaces. After 15 min, the surface was scrubbed with a cotton pellet and moistened with ethanol or acetone, compounding the following groups: G1-99.5% ethanol and G2-acetone, without previous use of dentin adhesive; G3-99.5% ethanol and G4-acetone, with previous use of dentin adhesive. The dentin surface was scrubbed until the cement residues could not be visually detected. Sections were then processed for scanning electron microscopy and evaluated at 500× magnification and scores were attributed to each image according to the area covered by residual sealer, and data were subjected to Kruskal-Wallis at 5% significance. The lower residue presence was observed in G3 (P = 0.005). All surface presented cement residues when acetone was used as cleaning solution (P = 0.0005). The cleaning solutions were unable to completely remove the cement residues from both surfaces. The ethanol used after previous application of the dentin adhesive promoted the lower presence of residues.
Assuntos
Colagem Dentária/métodos , Cimentos Dentários/química , Adesivos Dentinários/química , Dentina/fisiologia , Endodontia/métodos , Metacrilatos/química , Condicionamento Ácido do Dente/métodos , Animais , Bovinos , Cimentos Dentários/uso terapêutico , Adesivos Dentinários/uso terapêutico , Metacrilatos/uso terapêutico , Microscopia Eletrônica de VarreduraRESUMO
The aim of this study was to evaluate the persistence of resin cement residues after dentin surface cleaning with different alcohol-based solutions or an essential oil (eucalyptol). Forty bovine teeth were sectioned in order to expose pulp chamber dentin to be washed with 1.0 mL of 2.5% sodium hypochlorite (NaOCl), followed by 0.1 mL of 17% EDTA application for 3 min, and final irrigation with 2.5% NaOCl. The specimens were air dried and resin-based cement was rubbed onto the dentine surface with a microbrush applicator. After 15 min, the surface was scrubbed with a cotton pellet and moistened with different dentin cleaning solutions, compounding the following groups: G1--95% ethanol, G2--70% ethanol, G3--70% isopropyl alcohol, or G4--eucalyptol. The dentin was scrubbed until the cement residues could not be visually detected. Sections were then processed for SEM and evaluated at × 500 magnification. Scores were attributed to each image according to the area covered by residual sealer, and data were subjected to Kruskal-Wallis at 5% significance. Eucalyptol promoted the most adequate dentin cleaning, although no statistical difference was detected amongst the groups (P > 0.05), except between the eucalyptol and 70% ethanol groups (P < 0.05). All the evaluated dentin cleaning solutions were unable to completely remove the cement residues from the dentin surface.
Assuntos
Álcoois/uso terapêutico , Cicloexanóis/uso terapêutico , Cimentos Dentários/análise , Cimentos Dentários/uso terapêutico , Dentina/química , Dentina/efeitos dos fármacos , Monoterpenos/uso terapêutico , Dente não Vital , Animais , Bovinos , Dentina/ultraestrutura , Eucaliptol , Incisivo , Microscopia Eletrônica de VarreduraRESUMO
A velocidade de absorção, por cones de papel absorvente, em função dos irrigantes (I) tergentol, (II) soro fisiológico, (III) irrigocal, (IV) endocris e (V) solução de Milton foi avaliada através do método proposto por HOLLAND et alii. Observou-se escala crescente do tempo de absorção, dos grupos I e V, existindo diferença entre os grupos extremos (p<0,05)
Assuntos
Humanos , Masculino , Feminino , Preparo de Canal RadicularRESUMO
Trinta caninos humanos extraídos, tiveram seus canais radiculares preenchidos com cimento de óxido de zinco e eugenol. Em seguida, foram realizadas a apicectomia e a preparação para obturação retrógrada. Utilizou-se como agentes irrigadores, o soro fisiológico, EDTA e ácido cítrico a 2 por cento, realizando-se em seguida a retro-obturação com o cimento de óxido de zinco e eugenol. Após a imersão em solução de azul-de-metileno a 2 por cento por sete dias, a infiltração marginal foi analisada, denotando-se menor magnitude para o soro fisiológico, com diferença significante em relação ao ácido cítrico a 2 por cento (p>0,05)