Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 3 de 3
Filtrar
Mais filtros











Intervalo de ano de publicação
1.
Braz Oral Res ; 282014.
Artigo em Inglês | MEDLINE | ID: mdl-24918368

RESUMO

The purpose of this study was to assess the color of layered resin overlays and to test the early microhardness of dual cure resin cement (DCRC) light cured through the layered resin overlays. Resin overlays of 1.5 mm thickness were fabricated with the A3 shade of Z350 (Group 1L), the A3B and A3E shades of Supreme XT (Group 2L), and the A3, E3, and T1 shades of Sinfony (Group 3L) using one, two, and three layers, respectively (n=7). Each layer of the resin overlays was set in equal thickness. The color of the resin overlays was measured with a colorimeter and compared with an A3 shade resin denture tooth. DCRC was light cured through the resin overlays, and the early microhardness of the DCRC was measured. The ΔE value between the denture tooth and the resin overlays and the Vickers hardness number (VHN) of the DCRC were analyzed with one-way ANOVA and Tukey's HSD test. The color differences were 8.9±0.5, 5.3±1.0, and 7.3±0.5 and the VHNs were 19.4±1.1, 21.1±0.9, and 29.3±0.6 for Groups 1L, 2L, and 3L, respectively. Therefore, to match the designated tooth color of resin inlays and to increase the early microhardness of DCRC, layered resin inlays are more appropriate than single-dentin-layer resin inlays. However, the translucent layer should be used cautiously because the color difference of resin inlays with a translucent layer was affected more than those without a translucent layer.


Assuntos
Lâmpadas de Polimerização Dentária , Revestimento de Dentadura , Pigmentação em Prótese , Cimentos de Resina/química , Análise de Variância , Colorimetria , Testes de Dureza , Humanos , Restaurações Intracoronárias/métodos , Teste de Materiais , Polimerização , Valores de Referência , Reprodutibilidade dos Testes , Cimentos de Resina/efeitos da radiação , Propriedades de Superfície , Fatores de Tempo
2.
J Appl Oral Sci ; 20(5): 576-80, 2012.
Artigo em Inglês | MEDLINE | ID: mdl-23138746

RESUMO

OBJECTIVE: The aim of this study was to evaluate the effect of multiple layers of an infection control barrier on the micro-hardness of a composite resin. MATERIAL AND METHODS: One, two, four, and eight layers of an infection control barrier were used to cover the light guides of a high-power light emitting diode (LeD) light curing unit (LCU) and a low-power halogen LCU. The composite specimens were photopolymerized with the LCUs and the barriers, and the micro-hardness of the upper and lower surfaces was measured (n=10). The hardness ratio was calculated by dividing the bottom surface hardness of the experimental groups by the irradiated surface hardness of the control groups. The data was analyzed by two-way ANOVA and Tukey's HSD test. RESULTS: The micro-hardness of the composite specimens photopolymerized with the LED LCU decreased significantly in the four- and eight-layer groups of the upper surface and in the two-, four-, and eight-layer groups of the lower surface. The hardness ratio of the composite specimens was <80% in the eight-layer group. The micro-hardness of the composite specimens photopolymerized with the halogen LCU decreased significantly in the eight-layer group of the upper surface and in the two-, four-, and eight-layer groups of the lower surface. However, the hardness ratios of all the composite specimens photopolymerized with barriers were <80%. CONCLUSIONS: The two-layer infection control barrier could be used on high-power LCUs without decreasing the surface hardness of the composite resin. However, when using an infection control barrier on the low-power LCUs, attention should be paid so as not to sacrifice the polymerization efficiency.


Assuntos
Resinas Compostas/química , Lâmpadas de Polimerização Dentária , Controle de Infecções Dentárias/métodos , Análise de Variância , Resinas Compostas/efeitos da radiação , Testes de Dureza , Humanos , Teste de Materiais , Polimerização , Propriedades de Superfície , Fatores de Tempo
3.
J. appl. oral sci ; J. appl. oral sci;20(5): 576-580, Sept.-Oct. 2012. tab
Artigo em Inglês | LILACS | ID: lil-654924

RESUMO

OBJECTIVE: The aim of this study was to evaluate the effect of multiple layers of an infection control barrier on the micro-hardness of a composite resin. MATERIAL AND METHODS: One, two, four, and eight layers of an infection control barrier were used to cover the light guides of a high-power light emitting diode (LeD) light curing unit (LCU) and a low-power halogen LCU. The composite specimens were photopolymerized with the LCUs and the barriers, and the micro-hardness of the upper and lower surfaces was measured (n=10). The hardness ratio was calculated by dividing the bottom surface hardness of the experimental groups by the irradiated surface hardness of the control groups. The data was analyzed by two-way ANOVA and Tukey's HSD test. RESULTS: The micro-hardness of the composite specimens photopolymerized with the LED LCU decreased significantly in the four- and eight-layer groups of the upper surface and in the two-, four-, and eight-layer groups of the lower surface. The hardness ratio of the composite specimens was <80% in the eight-layer group. The micro-hardness of the composite specimens photopolymerized with the halogen LCU decreased significantly in the eight-layer group of the upper surface and in the two-, four-, and eight-layer groups of the lower surface. However, the hardness ratios of all the composite specimens photopolymerized with barriers were <80%. CONCLUSIONS: The two-layer infection control barrier could be used on high-power LCUs without decreasing the surface hardness of the composite resin. However, when using an infection control barrier on the low-power LCUs, attention should be paid so as not to sacrifice the polymerization efficiency.


Assuntos
Humanos , Lâmpadas de Polimerização Dentária , Resinas Compostas/química , Controle de Infecções Dentárias/métodos , Análise de Variância , Resinas Compostas/efeitos da radiação , Testes de Dureza , Teste de Materiais , Polimerização , Propriedades de Superfície , Fatores de Tempo
SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA