RESUMO

Pharmaceutical active compounds (PhACs) are detected pollutants in aquatic environments worldwide at concentrations ranging from ng L-1 to µg L-1. Currently, PhAC monitoring is poorly realized in Mexico. This study proposes a priority list of PhACs in Mexican aquatic environments, considering their occurrence and environmental and human health risks. Ecological risks were assessed as Risk Quotients (RQ) values using the PhAC concentrations detected in surface water, obtaining high risks (RQ > 1) against aquatic organisms, especially of naproxen, ibuprofen, diclofenac, acetaminophen, 17ß-estradiol, carbamazepine, ketoprofen, caffeine. In contrast, potential human health risks (RQH) were assessed on the Mexican population using the concentrations quantified in groundwater, demonstrating potential risks (RQH > 0.2) on the population, particularly of DCF and CBZ. Thus, a priority list of PhACs can be used as a reference for environmental monitoring in Mexican water supplies as well as PhACs monitoring in countries of the Caribbean region and Central America.

Assuntos

RESUMO

Rapid synthesis of carbon-based magnetic materials derived from cobalt and iron metal-organic frameworks (MOFs), ZIF-67, and MIL-100(Fe), by microwave-assisted method, followed by carbonization under a N2 atmosphere is described in this study. The carbon-derived MOFs (CDMs) were evaluated for the removal of the emerging pollutants sulfadiazine (SDZ) and flumequine (FLU) used as veterinary drugs. The study aimed to link the adsorption behavior with their surface properties and elemental composition. C-ZIF-67 and C-MIL-100(Fe) showed hierarchical porous structures with specific surface areas of 295.6 and 163.4 m2 g-1, respectively. The Raman spectra of the CDMs show the characteristic D and G bands associated with defect-rich carbon and sp2 graphitic carbon, respectively. The CDMs exhibit cobalt species (Co3O4, CoO, and Co) in C-ZIF-67 and iron species (Fe2O3, Fe3O4, and Fe) in C-MIL-100 (Fe) which are related to the magnetic behavior of CDMs. C-ZIF-67 and C-MIL-100 (Fe) had saturation magnetization values of 22.9 and 53.7 emu g-1, respectively, allowing easy solid-liquid separation using a magnet. SDZ and FLU removal rates on CDMs follow pseudo-second-order kinetics, and adsorption isotherms fit the Langmuir model based on regression coefficient values. Adsorption thermodynamics calculations showed that the adsorption of SDZ and FLU by CDMs was a thermodynamically favorable process. Therefore, these properties of C-ZIF-67 and C-MIL-100 (Fe) and their regeneration ability facilitate their use as adsorbents for emerging pollutants.

Assuntos

RESUMO

Five endocrine-disrupting compounds (EDCs) were determined in four urban wastewater treatment plants (WWTPs) of the Metropolitan Area of Monterrey (MAM) in two seasonal periods (winter and summer). The MAM, one of the most urbanized areas in Mexico, is characterized by high industrial activity and population density, leading to extensive use of several EDCs. In the MAM, ∼90% of urban and industrial wastewater is treated in WWTPs, where EDCs can be partially eliminated. In this work, dissolved levels of 17ß-estradiol (E2), 17α-ethinyl estradiol (EE2), bisphenol A (BPA), 4-nonylphenol (4NP), and 4-tert-octylphenol (4TOP) in wastewater were determined. The EDCs' determination was carried out through solid-phase extraction (SPE) and gas chromatography coupled to mass spectrometry (GC-MS). High EDCs levels (0.4-450 ng/L) were found in the influents of WWTPs, while concentrations in the effluents ranged from 0.2 to 26.8 ng/L, with E2, EE2, and 4TOP being the most persistent. The Spearman correlation analysis revealed the association between E2 and EE2 (r = 0.4835, p < 0.05), and between BPA and 4NP (r = 0.5180, p < 0.05), suggesting that these EDCs have similar sources. Also, E2, BPA, and 4TOP were positively correlated with the chemical oxygen demand (COD), biochemical oxygen demand (BOD), and total suspended solids (TSS) (r = 0.4080-0.5694, p < 0.05), indicating the association of the EDCs with the organic matter in the wastewater. The factor analysis confirmed the significant correlation of COD, BOD, TSS, temperature, and pH with the high occurrence of 4TOP during the summer. It was also confirmed that summer warmer temperatures favored the removal of BPA and 4NP in the studied WWTPs. Finally, the studied sites were classified by cluster analysis in three groups, revealing the impact that seasonality has on the behavior of the selected EDCs.

Assuntos

RESUMO

A solid-phase extraction methodology using a MIL-101(Fe)/PVDF membrane was proposed as a useful alternative for the simultaneous determination of naproxen, diclofenac, and ibuprofen, three anti-inflammatory drugs (NSAIDs), in wastewater samples by HPLC-CCD analysis. The MIL-101(Fe) was prepared by a rapid microwave-assisted method and supported in a polymeric PVDF membrane. The prepared material was characterized by X-ray diffraction (XRD), nitrogen adsorption-desorption, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared spectroscopy (FT-IR). The factors that affect the extraction of the NSAIDs using the MIL-101(Fe)/PVDF membrane as the sample volume, the solution pH and the elution solvent were studied in detail. The selected conditions were 50 mL of sample solution at pH 3 and 5 mL of methanol: acetone (30:70, v v-1) acidified with formic acid at 2% as elution solvent. The analytical method was linear with determination coefficients (r2 ≥ 0.998) in the calibration ranges from 2 to 100 ng mL-1 for naproxen, 20-200 ng mL-1 for diclofenac, and 100-300 ng mL-1 for ibuprofen. The intra and inter-day precision (repeatability and reproducibility, respectively) of the method (RSD%, n = 5) were lower than 4.8% and 7.1%, respectively. The accuracy reported as recovery percentages ranged from 82 to 118%, and the limits of detection were between 1.8 and 32.3 ng mL-1. Moreover, MIL-101(Fe)/PVDF membrane exhibited improved adsorption efficiency compared to that of its analog MIL-101(Cr)/PVDF and the pristine PVDF membranes, obtaining in an easy and rapid (60 min) way a low-cost and low-toxic adsorbent with excellent stability, reusability, mechanic resistance, and simple operation which shows excellent performance.

Assuntos

RESUMO

In this work, the dispersive solid-phase extraction of sulfonamide antibiotics was evaluated using magnetic porous carbons derived from cobalt(ii)-based metal-organic frameworks. By direct carbonization under the inert atmosphere of Co-SIM-1, Co-MOF-74 and Co-DABCO MOFs, different magnetic porous carbons were prepared and characterized to study their structural, morphological, chemical and textural properties. Their performance for the simultaneous extraction of three sulfonamides (sulfadiazine, sulfamerazine and sulfamethazine), prior to HPLC analysis, was also evaluated, obtaining the best results (>95%) in the case of C/Co-SIM-1 carbon, probably due to its bimodal pore structure, high surface area and large amount of surface defects. Using this adsorbent, the effect of the solution pH and contact time on the adsorption of the sulfonamides, and the reusability of the carbon were studied.

RESUMO

A fully automated on-line system for monitoring the TiO2-based photocatalytic degradation of dimethyl phthalate (DMP) and diethyl phthalate (DEP) using sequential injection analysis (SIA) coupled to liquid chromatography (LC) with UV detection was proposed. The effects of the type of catalyst (sol-gel, Degussa P25 and Hombikat), the amount of catalyst (0.5, 1.0 and 1.5 g L-1), and the solution pH (4, 7 and 10) were evaluated through a three-level fractional factorial design (FFD) to verify the influence of the factors on the response variable (degradation efficiency, %). As a result of FFD evaluation, the main factor that influences the process is the type of catalyst. Degradation percentages close to 100% under UV-vis radiation were reached using the two commercial TiO2 materials, which present mixed phases (anatase/rutile), Degussa P25 (82%/18%) and Hombikat (76%/24%). 60% degradation was obtained using the laboratory-made pure anatase crystalline TiO2 phase. The pH and amount of catalyst showed minimum significant effect on the degradation efficiencies of DMP and DEP. Greater degradation efficiency was achieved using Degussa P25 at pH 10 with 1.5 g L-1 catalyst dosage. Under these conditions, complete degradation and 92% mineralization were achieved after 300 min of reaction. Additionally, a drastic decrease in the concentration of BOD5 and COD was observed, which results in significant enhancement of their biodegradability obtaining a BOD5/COD index of 0.66 after the photocatalytic treatment. The main intermediate products found were dimethyl 4-hydroxyphthalate, 4-hydroxy-diethyl phthalate, phthalic acid and phthalic anhydride indicating that the photocatalytic degradation pathway involved the hydrolysis reaction of the aliphatic chain and hydroxylation of the aromatic ring, obtaining products with lower toxicity than the initial molecules.

RESUMO

An on-line solid phase extraction coupled to liquid chromatography with UV detection (SPE/LC-UV) method was automated by the multisyringe flow-injection analysis (MSFIA) system for the determination of three phthalic acid esters (PAEs). The PAEs determined in drinking water stored in polyethylene terephthalate (PET) bottles of ten commercial brands were dimethyl phthalate (DMP), diethyl phthalate (DEP) and dibutyl phthalate (DBP). C18-bonded silica membrane was used for isolation and enrichment of the PAEs in water samples. The calibration range of the SPE/LC-UV method was 2.5-100µgL-1 for DMP and DEP and 10-100µgL-1 for DBP with correlation coefficients (r) ranging from 0.9970 to 0.9975. Limits of detection (LODs) were between 0.7 and 2.4µgL-1. Inter-day reproducibility performed at two concentration levels (10 and 100µgL-1) expressed as relative standard deviation (%RSD) were found in the range of 0.9-4.0%. The solvent volume was reduced to 18mL with a total analysis time of 48min per sample. The major species detected in bottled water samples was DBP reaching concentrations between 20.5 and 82.8µgL-1. The recovery percentages for the three analytes in drinking water were 80-115%. The migration test showed a great variation in the sum of migrated PAEs level (10.2-50.6µgL-1) among the PET bottle brands analyzed indicating that the presence of these contaminants in the plastic containers may depend on raw materials and the conditions used during their production process.

Assuntos

RESUMO

A fully automated on-line system for monitoring the photocatalytic degradation of herbicides was developed using multisyringe flow injection analysis (MSFIA) coupled to a solid phase extraction (SPE) unit with UV detection. The calibration curves were linear in the concentration range of 100-1000 µg L(-1) for 3,6-dichloro-2-methoxybenzoic acid (dicamba) and 500-3000 µg L(-1) for 2,4-dichlorophenoxyacetic acid (2,4-D), while the detection limits were 30 and 135 µg L(-1) for dicamba and 2,4-D, respectively. The monitoring of the photocatalytic degradation (TiO2 anatase/UV 254 nm) of these two herbicides was performed by MSFIA-SPE system using a small sample volume (2 mL) in a fully automated approach. The degradation was assessed in ultrapure and drinking water with initial concentrations of 1000 and 2000 µg L(-1) for dicamba and 2,4-D, respectively. Degradation percentages of approximately 85% were obtained for both herbicides in ultrapure water after 45 min of photocatalytic treatment. A similar degradation efficiency in drinking water was observed for 2,4-D, whereas dicamba exhibited a lower degradation percentage (75%), which could be attributed to the presence of inorganic species in this kind of water.

Assuntos

RESUMO

The prevalence of heavy metal pollution and mobility of both Pb and Cd was investigated in street dust samples from the Metropolitan Area of Monterrey (MAM) in northern Mexico. Street dust samples from 30 selected sites were analysed for their content of Zn, Cd, Pb, Cr and Ni after digestion according to U.S. EPA Method 3051. Multivariate analysis including correlation coefficient analysis, Principal Component Analysis and Cluster Analysis was used to analyse the data and identify possible sources of these heavy metals. Compared with background values, elevated concentrations of Pb (300 mg kg(-1)), Cd (7.6 mg kg(-1)) and Cr (78 mg kg(-1)) were observed in street dust of MAM. Based on multivariate statistical approaches, the studied elements were classified in three main sources: (1) Cr, Ni and Zn mainly derived from industrial activities; (2) Cd originating from traffic-related activities; and (3) Pb associated with vehicular emissions. A sequential extraction procedure using the Tessier method was applied to evaluate the mobility of Pb and Cd in street dust. The majority of Pb was associated with the residual fraction followed by the carbonate fraction. The majority of Cd was associated with the residual fraction. These results indicated that the mobility was higher in Pb (26%) compared with Cd (11%), posing a potential risk to the environment.

Assuntos

RESUMO

The degradation of a model mixture composed of Acid Yellow 36 (AY36) and Methyl Orange (MO) azo dyes was performed using the photo-Fenton process (PFP). The performance of this process conducted under artificial UV light (365 nm) was compared with the Fenton reaction. Some important operating parameters that affect the degradation of azo dyes, such as initial Fe(2+) and H(2)O(2) concentrations and the presence or absence of chloride ions, were investigated. Decolorisation of the dye mixture sample was achieved in 70 min with the photo-Fenton reaction, while the complete mineralization evaluated by TOC abatement was completed in 180 min. These results provide important knowledge for the treatment of wastewater containing azo dye mixtures by Fenton and photo-Fenton oxidation processes.

RESUMO

The simple extraction-spectrophotometric procedure is proposed in this work for the determination of 2-(thiocyanomethylthiol)benzothiazole (TCMTB) in chrome tanning liquors after its breakdown to 2-mercaptobenzothiazole (MBT). The sample (50mul) was 4-fold diluted with deionized water and the conversion of TCMTB to MBT was obtained with cysteine (400 mul, 0.1 moll(-1)) in alkaline conditions (pH 10). After acidification to pH 2.5 (100 mul phosphoric acid, 2 moll(-1)), the extraction was carried out with 800 mul of ethyl acetate, containing 0.2% of beta-mercaptoethanol and absorbance was measured at 324 nm with the cut-off filter 295 nm. To avoid possible errors due to MBT presence in the sample, this same sample was taken for blank, but the reagents were added in form of one acid solution (omitting the conversion step). The calibration range was 10-120 mugml(-1) of TCMTB with the regression coefficient 0.9999, the quantitation limit was 2.80 mugml(-1) and the within day precision was 3.34 and 0.20%, respectively, for 10 and for 100 mugml(-1) of TCMTB. The results obtained in the analysis of the three industrial liquor samples by the proposed procedure were in a good agreement with the results obtained using liquid chromatography method.