RESUMO
Galvanic effluents are composed of a wide range of heavy metals, requiring adequate treatment to remove these contaminants and to meet the limits established by environmental agencies. Considering this aspect, the present study had as main objectives: (i) to evaluate the efficiency of the electrocoagulation (EC) in the treatment of a galvanic effluent, with the purpose of removing total Cr, Cu, Mn, Ni and (ii) reuse the sludge generated for inorganic pigment production. EC tests were carried out through factorial design 23 with triplicate central point. pH (3, 7, 11), reaction time (15, 22.5 and 30 min) and current density (10, 17.5 and 25 mA/cm2) were the control variables. Under ideal experimental conditions (pH 7.00; t = 22.5 min and DC = 17.5 mA/cm2) were removed 96.94% of Mn, 97.63% of Cu and 99.99% of total Cr and Ni, allowing to meet the limits provided in CONAMA Resolution 430/2011. The production of inorganic pigments from a mixture of 10% sludge (generated in the ideal experimental condition) and Al2O3 and TiO2 proved to be technically viable. It was obtained 8.27 g of a brown inorganic pigment, composed mainly of Al1.82Cr0.18O3, Ca0.999(Ti0.805Fe0.201)O2.899 and Fe2.18O4Ti0.42. Therefore, the results obtained demonstrate that EC is an effective technique in galvanic effluents treatment. The sludge generated in this process showed to be appropriated to be reused in inorganic pigment production and could be considered as an alternative to reduce the environmental impact related to electroplating process.
Assuntos
Metais Pesados , Purificação da Água , Corantes , Eletrocoagulação/métodos , Resíduos Industriais/análise , Esgotos , Purificação da Água/métodosRESUMO
The present study investigated the efficiency of physicochemical processes of coagulation and flocculation and Fenton advanced oxidative process in reducing the parameters of colour, turbidity and Chemical Oxygen Demand (COD) of a real effluent from a textile industry. During the physicochemical process, the efficiencies of different coagulants (aluminium polychloride (Polifloc 18), ferric chloride (Acquafloc FC40), aluminium sulphate combined with organic coagulant (AST) and aluminium sulphate) and nonionic (FX NS2), cationic (FX CS6 and FX CS7) and anionic (FX AS6 and AN905) flocculants were tested. After the tests, 72.60% of COD, 36.25% of colour and 98.59% of turbidity were removed, using aluminium polychloride coagulant and AN 905 flocculant. It was also evaluated the effect of Fenton advanced oxidative process application in removal of colour, COD and turbidity of the effluent previously treated through the physicochemical process. Removals of these parameters were analysed in two different pH ranges (pH 6.0 and 7.0). In both pH 6.0 and pH 7.0, reductions were observed in all analysed parameters, obtaining 170.78â mg O2/L of COD, 22.19â mg/L of colour and 0.80 NTU of turbidity (at pH 6.0) and 151.80â mg O2/L of COD, 26.73â mg/L of colour, 0.94 NTU of turbidity (at pH 7.0), which demonstrates the efficiency of this process in the reduction of parameters analysed.
Assuntos
Eliminação de Resíduos Líquidos , Poluentes Químicos da Água , Análise da Demanda Biológica de Oxigênio , Cor , Floculação , TêxteisRESUMO
A combination of electrocoagulation and coagulation-flocculation processes was used for re-refining effluent from lubricating oils. The efficiency of the process was evaluated based on the chemical oxygen demand (COD), color, and turbidity of the refined effluent. Electrocoagulation (EC) and coagulation-flocculation parameters, such as the initial pH (3.00, 4.41, and 9.00), and current density (4, 9, and 16 A/m2), and the use of aluminum polychloride coagulant and superfloc A300 flocculant were studied. EC performed at pH 9, with a current density of 16 A/m2 and 7 V, resulted in removal efficiencies of 85.14%, 99.81%, and 99.85%, for COD, color, and turbidity, respectively. The removal efficiencies increased to 96%, 99.87%, and 99.94% for COD, color, and turbidity, respectively, by the further coagulation-flocculation treatment in the presence of 13.8 mg/L aluminum polychloride coagulant and 80 mg/L Superfloc A300 flocculant.