RESUMO
BACKGROUND: The aim of this study was to characterize solid particulate aerosol derived from a cutlery microenterprise and to investigate substances associated with activities performed within the work environment. OBJECTIVE: Suspended particulate matter (SPM) was collected at different locations in the cutlery workshop and near machines used by workers, using passive sampling devices fitted with polytetrafluoroethylene filters, onto which total particulate material was deposited. The substances present in the SPM were analyzed using gas chromatography-mass spectrometry (GC-MS). RESULTS: Identification of the substances was performed using the National Institute of Standards (NIST) library and automated mass spectral deconvolution and identification system. (AMDIS) software, considering at least 70% probability. The concentration of total dust, obtained using a gravimetric method, was approximately 1âmg.m-3. CONCLUSION: The toxic substances found in the SPM included halogenated hydrocarbons (containing chlorine, fluorine, and iodine) and aromatic hydrocarbons. The toxic substances included naphthalene, which is classified as carcinogenic.
Assuntos
Hidrocarbonetos Aromáticos/análise , Hidrocarbonetos Halogenados/análise , Material Particulado/análise , Poluentes Ocupacionais do Ar/análise , Brasil , Cromatografia Gasosa-Espectrometria de Massas , Utensílios Domésticos , Naftalenos/análise , Empresa de Pequeno PorteRESUMO
Polychlorinated biphenyls (PCBs) are carcinogenic to humans and can be found in fuller's earth used for the treatment of used transformer oil. This work describes an optimization of the Fenton process for the removal of contaminants from fuller's earth. The effects of pH (2.5 and 4.0), [H2O2] (1.47 and 2.07â molâ L-1), and [Fe2+] (1.7 and 40â mmolâ L-1) were studied. The Fenton process efficiency was monitored using the decreases in the chemical oxygen demand (COD) and the concentrations of oil and grease, total carbon (TC), PCBs, and H2O2. The fuller's earth contaminated with insulating oil presented 35% (w/w) of TC, 34% (w/w) of oil and grease, 297.0â gâ L-1 COD, and 64â mg of PCBs per kg. The material could therefore be considered a dangerous waste. After Fenton treatment, using a slurry mode, there was a removal of 55% of COD, 20% of oil and grease, and 20% of TC, achieved at pH 2.5 using 2.07â molâ L-1 of H2O2 and 40.0â mmolâ L-1 of Fe2+. No PCBs were detected in the samples after the Fenton treatment, even using smaller amounts of Fenton reagents (1.47â molâ L-1 of H2O2, 1.7â mmolâ L-1 of Fe2+, pH 2.5). The results indicated that the treated fuller's earth was free from PCB residues and could be disposed of in a simple landfill, in accordance with Brazilian PCB regulations.
Assuntos
Bifenilos Policlorados , Compostos de Alumínio , Brasil , Humanos , Peróxido de Hidrogênio , Compostos de Magnésio , Oxirredução , SilicatosRESUMO
Protective clothing is used as a barrier against pesticides when working with agricultural sprays. The aim of this study was to evaluate the pesticide penetration, retention, and repellence of the material and seams of a whole-body protective garment used by applicators of pesticides. The efficiency of the material and seams of the whole-body garment were determined for its classification as proposed by ISO 27065 (ISO, 2011). The evaluation method used was the pipette test of ISO 22608. The efficiency of the material and seams of the garment (100% cotton) were tested by contamination with formulations of Roundup Original® SL; Nufos EC® and Supera SC®. The presence of the seams in the protective clothing reduced its efficiency in the control of dermal exposure, except when protecting against the Supera SC® formulation. The number of washes and uses affected the efficiency of the material and seams of the garment. The type of formulation interfered significantly in the penetration of pesticides into the material and seams. Thus, the laboratory efficiency assessment of protective clothing is necessary to determine what types of formulations and use conditions are appropriate for workers.