Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 3 de 3
Filtrar
Mais filtros











Base de dados
Intervalo de ano de publicação
1.
Clin Oral Investig ; 28(1): 45, 2023 Dec 28.
Artigo em Inglês | MEDLINE | ID: mdl-38153515

RESUMO

OBJECTIVE: This study aimed to investigate changes in the surface characteristics of two denture resins when disinfected with a vinegar-hydrogen peroxide (VHP) mixture. MATERIALS AND METHODS: Microwave-polymerized or 3D printed acrylic resin disks were immersed for 900 min (simulating 90 daily uses) in the following solutions (N = 10): water; 0.5% sodium hypochlorite; hydrogen peroxide and water dilution (1:1 ratio); vinegar and water dilution (1:1 ratio); and VHP mixture. Surface roughness, Knoop microhardness, surface free energy, and scanning electron microscopic images were assessed before and after the immersions. Results were compared using the 2-way ANOVA for repeated measures and Tukey test, at 5% significance. RESULTS: Surface roughness and microhardness did not differ (P > .05) among the solutions and times. Surface free energy and its dispersive component increased (P < .05) for all solutions. All solutions, except for water and VHP mixture, degraded microtopography. CONCLUSIONS: The VHP mixture was not deleterious to conventional and 3D-printed resin surfaces. CLINICAL RELEVANCE: Conventional and 3D printed resin dentures can be disinfected with a VHP mixture in a 1:1 ratio because this mixture does not substantially affect the surface characteristics after 90 daily immersions. On the contrary, sodium hypochlorite, hydrogen peroxide, and vinegar solutions, even in low concentrations, should be used with caution for denture disinfection because they may alter the resin microtopography over time.


Assuntos
Ácido Acético , Desinfecção , Peróxido de Hidrogênio , Hipoclorito de Sódio , Resinas Acrílicas , Água , Dentaduras
3.
J Endod ; 46(7): 980-986, 2020 Jul.
Artigo em Inglês | MEDLINE | ID: mdl-32439224

RESUMO

INTRODUCTION: The aim of this ex vivo study was to analyze the effect of different vehicles combined with agitation methods on the penetration of calcium hydroxide (CH) paste in the dentinal tubules. METHODS: Sixty freshly extracted, single-rooted human premolars were prepared using WaveOne Gold (Dentsply Sirona, York, PA) and randomized into 6 experimental groups (n = 10) according to the vehicle and method of paste agitation as follows: propylene glycol (PG) + Lentulo, PG + Lentulo + ultrasound, PG + Lentulo + sonic, distilled water (DW) + Lentulo, DW + Lentulo + ultrasonic, and DW + Lentulo + sonic. The CH paste was manipulated with sodium fluorescein dye and was inserted to completely fill the root canal. Two 1-mm thick sections at 2 mm and 5 mm from the apex of each root were obtained. The sections were scanned using confocal laser scanning microscopy, and the images were analyzed using ImageJ software (Bethesda, MD) to calculate the percentage penetration and maximum penetration depth of CH paste. Statistical analysis was performed using 1-way analysis of variance and Tukey honestly significant difference post hoc tests. RESULTS: No statistically significant differences between study factors at a distance of 2 mm from the apex were observed (P > .05). However, at 5 mm, a significant difference between the vehicles (P < .05) in percentage penetration was demonstrated with higher means for PG. CONCLUSIONS: Vehicles interfered with the penetration of CH in the dentinal tubules at 5 mm from the apex with better results for PG.


Assuntos
Hidróxido de Cálcio , Irrigantes do Canal Radicular , Dente Pré-Molar , Cavidade Pulpar , Dentina , Humanos , Microscopia Confocal , Tratamento do Canal Radicular
SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA