RESUMO
This research focuses on the development of a state observer for performing indirect measurements of the main variables involved in the soybean oil transesterification reaction with a guishe biochar-based heterogeneous catalyst; the studied reaction takes place in a batch reactor. The mathematical model required for the observer design includes the triglycerides' conversion rate, and the reaction temperature. Since these variables are represented by nonlinear differential equations, the model is linearized around an operation point; after that, the pole placement and linear quadratic regulator (LQR) methods are considered for calculating the observer gain vector L(x). Then, the estimation of the conversion rate and the reaction temperature provided by the observer are used to indirectly measure other variables such as esters, alcohol, and byproducts. The observer performance is evaluated with three error indexes considering initial condition variations up to 30%. With both methods, a fast convergence (less than 3 h in the worst case) of the observer is remarked.
RESUMO
Most conventional methods to remove heavy metals from water are efficient for high concentrations, but they are expensive, produce secondary pollution, and cannot remove low concentrations. This paper proposes a biological system to remove Cr(VI) from aqueous solutions; the biofilter is composed of a native Pseudomonas koreensis immobilized in calcium alginate beads. Lab experiments were conducted in batch reactors, considering different operating conditions: Cr(VI) concentration, temperature, pH, and time. At 30 °C and a pH of 6.6, the immobilized bacteria achieved their optimal adsorption capacity. In the chromium adsorption system, saturation was reached at 30 h with a qmax = 625 mg g-1. By adjusting the experimental data to the Langmuir and Freundlich models, it is suggested that P. koreensis forms a biofilm with a homogeneous surface where Cr(VI) is adsorbed and that the bacteria also incorporates the metal in its metabolism, leading to a multilayer adsorption. On the other hand, using Fourier transform infrared spectroscopy, it was inferred that the functional groups involved in the adsorption process were O-H and C=O, which are a part of the P. koreensis cell wall.
Assuntos
Poluentes Químicos da Água , Purificação da Água , Água , Adsorção , Alginatos/química , Poluentes Químicos da Água/análise , Cromo/análise , Purificação da Água/métodos , Concentração de Íons de Hidrogênio , Cinética , Espectroscopia de Infravermelho com Transformada de FourierRESUMO
Pecan nut (Carya illinoensis) pericarp is usually considered as a waste, with no or low value applications. Its potential as a densified solid biofuel has been evaluated, searching for alternatives to generating quality renewable energy and reducing polluting emissions in the atmosphere, based on particle size, that is an important feedstock property. Therefore, agro-industrial residues from the pecan nut harvest were collected, milled and sieved to four different granulometry: 1.6 mm (N° 12), 0.84 mm (N° 20), 0.42 mm (N° 40), and 0.25 mm (N° 60), used as raw material for biofuel briquette production. The carbon and oxygen functional groups in the base material were investigated by Fourier transform infrared spectroscopy (FTIR) and proximate analyses were performed following international standards, for determining the moisture content, volatile materials, fixed carbon, ash content, and calorific value. For the biofuel briquettes made from base material of different particle sizes, the physical characteristics (density, hardness, swelling, and impact resistance index) and energy potential (calorific value) were determined to define their quality as a biofuel. The physical transformation of the pecan pericarp wastes into briquettes improved its quality as a solid biofuel, with calorific values from around 17.00 MJ/kg for the base material to around 18.00 MJ/kg for briquettes, regardless of particle size. Briquettes from sieve number 40 had the highest density (1.25 g/cm3). Briquettes from sieve number 60 (finest particles) presented the greater hardness (99.85). The greatest susceptibility to swelling (0.31) was registered for briquettes with the largest particle size (sieve number 20). The IRI was 200 for all treatments.
RESUMO
Citrus wax is a waste generated during the purification process of the citrus essential oil. A lot of citrus wax wastes are globally produced, despite this, its composition and properties are not well known. Here we present comprehensive results proving the chemical composition and the physical properties of citrus wax. Additionally, our study provides the basis for obtaining value-added products from citrus wax wastes. The qualitative/quantitative analysis revealed the presence of different compounds, which range from flavonoids, saponins, carbohydrates, unsaturated compounds, phenolic hydroxyls, and long-chain fatty acid esters. Given that citrus wax is a source of many bioactive compounds, they were preferably extracted with ethanol. The ethanolic extracts demonstrated the presence in citrus wax of different bioactives, such as 5-5'-dehydrodiferulic acid, 3,7-dimethylquercetin, 5,6-dihydroxy-7,8,3',4'-tetramethoxyflavone, tangeretin, and limonene. After the extraction of bioactives from citrus wax, a washed waxy material with high content of long-chain fatty acid esters was obtained. It was shown that this washed wax can be used for the production of biodiesel. The transesterification reactions in acid media was the preferred process because higher content of fatty acid methyl esters (such as hexadecanoic acid methyl ester and 9,12-octadecadienoic acid (Z,Z)-, methyl ester) were obtained. Currently, citrus wax does not have any industrial application, here we shown that under the concept of waste biorefinery, the citrus wax wastes are useful sources for producing value-added products such as bioactive compounds and biodiesel.