RESUMO
OBJECTIVE: To explore the relationship between ventricular filling curves and the extent of late enhancement on cardiac magnetic resonance imaging (MRI) in patients with hypertrophic cardiomyopathy. MATERIAL AND METHODS: We retrospectively included consecutive patients with suspected and/or confirmed hypertrophic cardiomyopathy and a control group of patients matched for age and sex who underwent cardiac MRI with evaluation of late enhancement. Among other determinations, we evaluated the following parameters on cine sequences: peak filling rate, time to the first peak filling rate, and filling rate normalized to the filling volume. RESULTS: Late enhancement was observed in 29 (73%) of the 40 patients with hypertrophic cardiomyopathy. The normalized peak filling rate was significantly lower in patients with late enhancement (4.9 ± 1.6 in those with hypertrophic cardiomyopathy positive for late enhancement vs. 5.8 ± 2.2 in those with hypertrophic cardiomyopathy negative for late enhancement vs. 6.3 ± 1.5 in controls, p = 0.008) and the time to peak filling was longer in patients with late enhancement (540.6 ± 89.7 ms vs. 505.5 ± 99.3 ms in those with hypertrophic cardiomyopathy negative for late enhancement vs. 486.9 ± 86.3 ms in controls, p = 0.02). When the population was stratified into three groups in function of the normalized peak filling rate, significant differences were observed among groups for age (p = 0.002), mean wall thickness (p = 0.036), and myocardial mass (p = 0.046) and atrial dimensions, whereas no significant differences with respect to late enhancement were seen. CONCLUSIONS: In patients with hypertrophic cardiomyopathy, we found a significant association between ventricular filling patterns and age, wall thicknesses, and atrial dimensions, but not with the extent of late enhancement.
Assuntos
Cardiomiopatia Hipertrófica/fisiopatologia , Ventrículos do Coração/diagnóstico por imagem , Ventrículos do Coração/fisiopatologia , Imageamento por Ressonância Magnética , Adulto , Técnicas de Imagem Cardíaca , Diástole , Feminino , Humanos , Masculino , Pessoa de Meia-Idade , Fatores de TempoRESUMO
This work presents the development of a liquid chromatographic method based on modeling entire fast scan fluorimetric detection second-order data with the multivariate curve resolution alternating least squares algorithm, for the simultaneous determination of five marker pteridines in urine samples. The modeling strategy involves the building of a single MCR-ALS model composed of matrices augmented in the spectral mode, i.e. time profiles remain invariant while spectra may change from sample to sample. This approach allowed us to separate and determine the whole analytes at once. The developed approach enabled us to determine five of the most important metabolic disorder marker pteridines: biopterin, neopterin, isoxanthopterin, pterin and xanthopterin, three of them presenting emission spectra with the same emission wavelength maxima. In addition, some of these analytes present overlapped time profiles. As a consequence of using the entire data sets, a considerable reduction of the data processing experimental time can be achieved. Results are compared with a previous strategy in which data were split in five different regions, and information about the figures of merit of the new strategy compared with the previously reported strategy is reported.
Assuntos
Biomarcadores/urina , Cromatografia Líquida de Alta Pressão/métodos , Modelos Teóricos , Pteridinas/urina , Espectrometria de Fluorescência/métodos , CalibragemRESUMO
The effect of piecewise direct standardization (PDS) and baseline correction approaches was evaluated in the performance of multivariate curve resolution (MCR-ALS) algorithm for the resolution of three-way data sets from liquid chromatography with diode-array detection (LC-DAD). First, eight tetracyclines (tetracycline, oxytetracycline, chlorotetracycline, demeclocycline, methacycline, doxycycline, meclocycline and minocycline) were isolated from 250 mL effluent wastewater samples by solid-phase extraction (SPE) with Oasis MAX 500 mg/6 mL cartridges and then separated on an Aquasil C18 150 mm x 4.6mm (5 microm particle size) column by LC and detected by DAD. Previous experiments, carried out with Milli-Q water samples, showed a considerable loss of the most polar analytes (minocycline, oxitetracycline and tetracycline) due to breakthrough. PDS was applied to overcome this important drawback. Conversion of chromatograms obtained from standards prepared in solvent was performed obtaining a high correlation with those corresponding to the real situation (r2 = 0.98). Although the enrichment and clean-up steps were carefully optimized, the sample matrix caused a large baseline drift, and also additive interferences were present at the retention times of the analytes. These problems were solved with the baseline correction method proposed by Eilers. MCR-ALS was applied to the corrected and uncorrected three-way data sets to obtain spectral and chromatographic profiles of each tetracycline, as well as those corresponding to the co-eluting interferences. The complexity of the calibration model built from uncorrected data sets was higher, as expected, and the quality of the spectral and chromatographic profiles was worse.
Assuntos
Cromatografia Líquida de Alta Pressão/métodos , Tetraciclinas/análise , Poluentes Químicos da Água/análise , Algoritmos , Modelos Teóricos , Tetraciclinas/isolamento & purificação , Eliminação de Resíduos LíquidosRESUMO
The use of multivariate spectrophotometric calibration for the simultaneous determination of dexamethasone and two typical excipients (creatinine and propylparaben) in injections is presented. The resolution of the three-component mixture in a matrix of excipients has been accomplished by using partial least-squares (PLS-1). Notwithstanding the elevated degree of spectral overlap, they have been rapidly and simultaneously determined with high accuracy and precision (comparable to the HPLC pharmacopeial method), with no interference, and without resorting to extraction procedures using non-aqueous solvents. A simple and fast method for wavelength selection in the calibration step is used, based on the minimisation of the predicted error sum of squares (PRESS) calculated as a function of a moving spectral window.