RESUMO
This work describes the synthesis of catalysts based on red mud/polyethylene terephthalate (PET) composites and their subsequent heat treatment under N2 atmosphere. The materials were characterized by scanning electron microscopy (SEM), temperature programmed reduction (TPR), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric (TG) analysis and N2 adsorption/desorption. The catalysts were evaluated in the oxidative desulfurization reaction of dibenzothiophene (DBT) in a biphasic system. The results indicated that the PET impregnation on red mud increased the affinity of the catalyst with the nonpolar phase (fuel), in which the contaminant was dissolved, allowing a higher conversion (up to 80%) and selectivity to the corresponding dibenzothiophene sulfone. The sulfone compound is more polar than DBT and diffused into the polar solvent as indicated by the data obtained via gas chromatography-mass spectrometry (GC-MS).
Assuntos
Modelos Químicos , Polietilenotereftalatos/química , Adsorção , Catálise , Oxirredução , Espectroscopia de Infravermelho com Transformada de Fourier , TiofenosRESUMO
In this study, we obtained a composite based on carbon/iron oxide from red mud and PET (poly(ethylene terephthalate)) wastes by mechanical mixture (10, 15 and 20wt.% of PET powder/red mud) followed by a controlled thermal treatment at 400°C under air. XRD analyses revealed that the α-Fe2O3 is the main phase formed from red mud. TPR analyses showed that the iron oxide present in the composites undergoes reduction at lower temperature to form Fe(2+) species present in Fe3O4, indicating that the iron oxide in the composite can exhibit greater reactivity in the catalytic processes compared to the original red mud. In fact, catalytic tests showed that the composites presented higher capacity to remove methylene blue dye (MB), presenting about 90% of removal after 24h of reaction. The MB removal was also monitored by mass spectrometer with ionization via electrospray (ESI-MS), which demonstrated the occurrence of the oxidation process, showing the formation of MB oxidation products. The stability of the composites was confirmed after four reuse cycles. The results seem to indicate that PET carbon deposited over the iron oxide from red mud promotes adsorption of the contaminant allowing its contact with the iron atoms and their consequent reaction.
RESUMO
The present work highlights the preparation of activated carbons (ACs) using spent coffee grounds, an agricultural residue, as carbon precursor and two different activating agents: water vapor (ACW) and K(2)CO(3) (ACK). These ACs presented the microporous nature and high surface area (620-950 m(2) g(-1)). The carbons, as well as a commercial activated carbon (CAC) used as reference, were evaluated as phenol adsorbent showing high adsorption capacity (≈150 mg g(-1)). The investigation of the pH solution in the phenol adsorption was also performed. The different activating agents led to AC with distinct morphological properties, surface area and chemical composition, although similar phenol adsorption capacity was verified for both prepared carbons. The production of activated carbons from spent coffee grounds resulted in promising adsorbents for phenol removal while giving a noble destination to the residue.
Assuntos
Carvão Vegetal/química , Café/química , Fenol/isolamento & purificação , Poluentes Químicos da Água/isolamento & purificação , Purificação da Água/métodos , Adsorção , Brasil , Microscopia Eletrônica de Varredura , Modelos Teóricos , Porosidade , Sementes/química , Propriedades de SuperfícieRESUMO
The adsorption features of activated carbon and the oxidation properties of iron oxides were combined in a composite to produce new materials for atrazine removal from aqueous medium. Activated carbon/iron oxide composites were prepared at 1/1 and 5/1 mass ratios and characterized with powder X-ray diffractometry (XRD), infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and nitrogen adsorption measurements. The adsorption and oxidation processes were evaluated in batch experiments, in order to monitor the atrazine removal capacity of these composites. The main iron oxide actually present in the composites was goethite (alpha-FeOOH). Impregnation with iron oxide reduced the surface area by its deposition in the activated carbon pores. However, a higher iron concentration promoted a higher oxidation rate, indicating that the efficiency of the oxidation reaction is related with the iron content and not with the pre-concentration of the contaminant on the carbon surface through adsorption process.