RESUMO

Paper is one of the packaging materials that presents a biodegradable character, being used in several areas; however, its barrier properties (gases and fat) and mechanics are reduced, which limits its application. Coating papers with synthetic polymers improve these properties, reducing their biodegradability and recyclability. The objective of this work was to develop and characterize coated paperboard, using the tape casting technique, with different ratios of film form agar-agar/chitosan (AA:CHI, 100:0, 50:50, and 0:100) and different numbers of coating layers (operating times for application of 14.25 min and 28.5 min for one and two layers, respectively). A significant reduction in water absorption capacity was found by applying a 0:100 coating (approximately 15%). Considering all coating formulations, the water vapor permeability reduced by 10 to 60% compared to uncoated paperboard, except for two layers coated with 0:100. The tensile index (independent of AA:CHI) was higher in the machine direction (22.59 to 24.99 MPa) than in the cross-section (11.87-13.01 MPa). Paperboard coated only with chitosan showed superior properties compared to the other formulation coatings evaluated.

RESUMO

Synthetic polymer coatings impact the biodegradable behavior of cellulosic packaging material. The environmental consequences of food packaging disposal have increased consumer concern. The present study aimed to use natural polymer coatings incorporating palmitic acid and activated carbon applied to paperboard surfaces as a sustainable alternative to improve cellulosic packaging material's moisture and fat barrier properties, minimizing the environmental impact. The coating formulation was defined using a Factorial Experimental Design with independent variables: chitosan, palmitic acid, activated carbon concentrations, and the number of coating layers. The highest concentration of chitosan (2.0% w/w) filled the pores of the cellulosic paperboard network, supporting the compounds incorporated into the filmogenic matrix and improving the fat resistance. The water vapor permeability of the coated paperboard material (range: 101 ± 43 to 221 ± 13 g·d-1·m-2) was influenced by the hydrophobicity effect of palmitic acid, the non-polar characteristic of activated carbon, and the number of applied layers. The coating formulation selected was a chitosan concentration of 2.0% (w/w), a palmitic acid concentration of 1.8% (w/w), an activated carbon concentration of 1.2% (w/w), and an application of three layers. The coating provides the potential for a paperboard surface application, improving the cellulosic packaging material's fat and moisture barrier properties and maintaining biodegradability and recyclability.

RESUMO

Starches are promising molecules in the production of edible films. However, the hydrophilic nature of these materials is among the main limitations of packaging based on natural polymers. An underexplored alternative is the incorporation of emulsions. This work aimed to produce films based on crosslinked cassava starch with emulsions based on watermelon seed oil (WSO) extracted with pressurized ethanol. The effect of incorporating watermelon seed oil emulsion (WSOE) on the microscopic, structural, mechanical, hydrophilic, and thermal properties of films was analyzed. The internal structure and roughness of the films were significantly affected by increasing WSOE concentration. The WSOE incorporation increased the elongation capacity of the films and reduced the strain at break. WSOE concentrations did not significantly affect the water solubility, permeability, and X-ray diffraction but decreased the wettability of the films. The analysis of the thermal properties showed that the films did not present phase separation in the studied temperature range. Overall, WSOE improved the properties of the films based on cross-linked cassava starch, but it is necessary to optimize the production conditions of the films. These materials may potentially be used as biodegradable food packaging, controlled-release films, and edible coatings in food protection.

RESUMO

Abstract The objective of this study was to evaluate the behavior of active compounds concentration present in the industrial by-product of acerola during drying using convective dehydration at 40, 50 and 60 °C. For this, flavones and flavonols, total proanthocyanidins, vitamin C, total phenolic content and antioxidant capacity as function of drying time were determined. The drying data were adjusted using the models of Page, Lewis, Henderson & Pabis, Modified Page and Logarithmic. In relation to the applied models, Page model presented the best fit. Acerola by-products dried at 40 °C showed higher concentrations of active compounds and higher antioxidant capacity. Although the drying process provoked changes in concentration of the active compounds, in the studied temperature range, significant concentrations of those bioactive compounds were observed. Thus, acerola by-product may present potential for application in different foods.

Assuntos

RESUMO

The present study evaluated the effect of the incorporation of copaiba oil, in direct and in microencapsulated form, into films based on Xanthosoma mafaffa Schott starch. Initially, the characterization of copaiba oil by gas chromatograph coupled with mass spectrometry (GC-MS) and its antimicrobial activity against gram-positive and gram-negative bacteria was performed. The films were produced by the casting technique and characterized in relation to physical, chemical, structural, and antimicrobial activity. Sesquiterpenes, mainly ß-caryophyllene, were the predominant compounds in copaiba oil, showing antimicrobial activity against B. subtilis and S. aureus. The films showed forming capacity, however, was observed a decrease in solubility and revealed an increase in hydrophobic characteristics. However, the oil reduced the tensile strength and elongation, while the microcapsules did not influence the mechanical properties in comparison to the control film. From microstructure analysis, changes in the films roughness and surface were observed after the addition of oil both directly and in microencapsulated form. Films incorporated with microparticles were able to inhibit the gram-positive bacteria tested, forming inhibition zones, indicating that the encapsulation of copaiba oil was more efficient for protecting bioactive compounds from the oil, suggesting the possible application of mangarito starch-based films incorporated with copaiba oil as biodegradable packaging.

RESUMO

Different baking conditions were used in order to evaluate its effects on bread aspects. Doughs were baked at 160, 190 and 220 °C, during 9, 12, 15 and 20 min, and characterized in relation to color change, oxalate and mineral concentration, and protein digestibility. The higher the baking temperature and time, the higher the crust color change, the lower the oxalate concentration, and the higher the amount of some macro minerals. Protein digestibility may also be favored, however it does not follow a linear correlation. Although it is not possible to obtain a condition that favors the content of all minerals, protein digestibility and reduces oxalate content, the use of high temperatures and times is important as it can reduce oxalate and thereby prevent its associated problems. Understanding how to optimize it during baking could be used to produce breads with a higher mineral bioavailability, an important strategy for food industry and also when using alternative flours.

Assuntos

RESUMO

In the orange juice industry, more than 50% of raw material becomes by-products that are rich in active compounds and have high nutritional content. Improved use of these by-products could represent a key strategy for a circular economy. The objective of this study was to produce a flour from orange juice by-product, characterize it, and then apply this flour to produce cookies. Orange by-product flour (OBPF) was characterized in terms of its chemical composition, dietary fiber, phenolic compounds, antioxidant potential, and hygroscopic properties. Subsequently, the effect of substituting wheat flour by OBPF in cookies was evaluated. OBPF presented a very high content of dietary fiber (73.61% dry matter (DM)), minerals (ash = 2.72% DM), and total phenolic compounds (534 ± 30 mg gallic acid equivalent (GAE)/100 g of DM). In general, the properties of cookies were not significantly influenced by using OBPF as a substitution for wheat flour. Sensorial analyses showed that cookies produced with 10% OBPF presented the higher scores. Therefore, OBPF showed interesting characteristics, suggesting its possible use in the development of fiber enriched foods such as cookies; and its production represents a key strategy for the orange juice processing industries towards the application of a circular economy in the food system.