RESUMO
Abstract This study aimed to compare the availability of supplies and amalgam and composite resin restorations among Oral Health Teams (OHT) in Brazilian regions. Secondary data were extracted from Modules I and II of the 1st (2012) and V and VI of the 2nd (2014) and 3rd cycle (2017) of the external evaluation of the National Program for Access and Quality in Primary Care2. The proportions between regions and cycles were compared using the Chi-square test with the z-test adjusted by the Bonferroni method (p<0.05). Among 2012, 2014, and 2017 there was a significant reduction in the proportion of OHT that performed amalgam restorations (87.5%, 89.2%, and 80.2%; p<0.001) and an increase in resin composite (92.5 %, 97.7%, and 99.0%; p<0.001), with the same trend in Brazilian regions (p<0.001). Amalgamator availability decreased among 2012 (99.0%), 2014 (98.4%) and 2017 (85.6%) (p<0.001). Amalgam availability was lower in 2017 (80.1%), compared to 2012 (87.5%) and 2014 (97.5%) (p<0.001). The availability of light curing decreased between 2012 (99.0%), 2014 (98.4%) and 2017 (85.6%) (p<0.001), being less available in the North (95.7%) (p<0.001). The light-curing resin increased between 2012 (94.1%), 2014 (96.6%) and 2017 (97.0%) (p<0.001), with no increase only in the North (p=0.134). While there was a reduction in supplies and amalgam restoration, there was an increase in supplies and resin composite restorations in the period evaluated in all Brazilian regions. However, regional disparities are still evident, with fewer supplies of restorative services in the North region.
Resumo Este estudo objetivou comparar a disponibilidade de fornecimentos e restaurações de amálgama e resina composta entre as Equipas de Saúde Oral (OHT) por regiões brasileiras. Os dados secundários foram extraídos dos módulos I e II do 1º (2012) e V e VI do 2º (2014) e 3º ciclo (2017) da avaliação externa do Programa Nacional de Acesso e Qualidade em Cuidados Primários. As proporções entre regiões e ciclos foram comparadas utilizando o teste Qui-quadrado com o teste z ajustado pelo método de Bonferroni (p<0,05). Entre 2012, 2014, e 2017 houve uma redução significativa na proporção de OHT que realizou restaurações de amálgama (87,5%, 89,2%, e 80,2%; p<0,001) e um aumento na resina composta (92,5%, 97,7%, e 99,0%; p<0,001), com a mesma tendência nas regiões brasileiras (p<0,001). A disponibilidade de amalgamadores diminuiu entre 2012 (99,0%), 2014 (98,4%) e 2017 (85,6%) (p<0,001). A disponibilidade de amálgama foi menor em 2017 (80,1%), em comparação com 2012 (87,5%) e 2014 (97,5%) (p<0,001). A disponibilidade de polimerização por luz diminuiu entre 2012 (99,0%), 2014 (98,4%) e 2017 (85,6%) (p<0,001), estando menos disponível no Norte (95,7%) (p<0,001). A resina fotopolimerizadora aumentou entre 2012 (94,1%), 2014 (96,6%) e 2017 (97,0%) (p<0,001), sem aumento apenas no Norte (p=0,134). Embora tenha havido uma redução nos fornecimentos e restauração de amálgamas, houve um aumento nos fornecimentos e restaurações de resina composta no período avaliado em todas as regiões brasileiras. Contudo, as disparidades regionais são ainda evidentes, com menos oferta de serviços de restauração na região Norte.
RESUMO
OBJECTIVES: To characterize the surface of zirconia (Y-TZP) submitted to different surface treatments (with and without plasma associations) and to evaluate the shear bond strength (SBS) between veneering ceramic (VC) and Y-TZP after different aging methods. METHODS: 301 Y-TZP specimens were fabricated and distributed into 7 groups: C (control): no treatment; Al: airborne abrasion with 27 µm Al2O3 particle; L: liner; P: plasma; Al + L: airborne + liner; Al + P: airborne + plasma; P + L: plasma + liner. The Y-TZP surface was characterized by SEM, EDS, AFM, surface profilometry, surface-free energy (SFE), and XRD. SBS between Y-TZP and VC was verified after three aging protocols: initial, after hydrothermal aging (autoclave for 5 h), or thermal fatigue (30,000 baths - 5-55 °C). One- (profilometry, SFE) and two-way ANOVA (SBS), and Tukey's HSD test were used. RESULTS: For the plasma groups, a full globular surface coverage was observed (SEM, AFM). Si was found for Al, L, Al + L, and P + L. Roughness was lower for C, P, and Al + P. For SFE, the highest values were found when the liner was applied (>74.59 nm/Nm). The highest monoclinic content was observed for Al + L (6.96%) and Al + P (5.86%). For the initial period, Al and P + L presented the lowest SBS values (<5.85 MPa; P > 0.331). The highest SBS values were found for L, P, and P + L (hydrothermal aging) and for P, L, Al + L, and Al + P (thermal fatigue). SIGNIFICANCE: Changes in Y-TZP topography and the SBS with the VC were found, according to treatments performed. Plasma treatment improved SBS and did not cause phase transformation.
Assuntos
Colagem Dentária , Cerâmica , Teste de Materiais , Microscopia Eletrônica de Varredura , Resistência ao Cisalhamento , Propriedades de Superfície , Ítrio , ZircônioRESUMO
OBJECTIVE: A silica-based nanofilm has been successfully deposited via Room-Temperature Atomic Layer Deposition (RT-ALD) on the surface of a glass. The purpose of this study was to evaluate the mechanical performance of a hybrid interface created between yttria-stabilized zirconia (Y-PSZ) transformed layer and silica-based nanofilm via RT-ALD. MATERIAL AND METHODS: Fully-sintered Y-PSZ (14 × 4.0 × 1.5 mm) specimens in different translucencies (MO, MT, LT; IPS e.max Zircad, Ivoclar Vivadent) were distributed in 5 groups: control (C - no treatment); hydrothermal treatment (HT- 15h, 134°C, 2 bar); alumina blasting (B - 50 µm Al2O3); RT-ALD silica deposition (S); HT followed by silica deposition (HTS). RT-ALD cycles consisted of the sequential exposure of specimens to tetramethoxysilane orthosilicate (TMOS - 60s) and ammonium hydroxide (NH4OH - 10 min) vapors in 40 cycles. Mechanical performance was analyzed by flexural strength (FS) (n = 10) and fatigue failure load (staircase method; n = 20) tests. Surface hardness (H) and Young's modulus (YM) were analyzed by nanoindentation. For surface chemical and topographical characterization, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were performed. Data from surface H, YM, FS, and fatigue limit (FL) were analyzed by two-way analysis of variance (ANOVA). RESULTS: The interaction between material and treatment had a significant effect on FS (p < 0.001). The FS values ranged from 436.23 MPa to 856.65 MPa. HT resulted in the highest FS (856.65 MPa) for LT and the lowest FS (436.23 MPa) for MO zirconia. For all materials, S and B treatments resulted in similar FS values (p > 0.410). S did not affect FL when compared to the C group (p > 0.277) for any material investigated. HTS resulted in higher FL than S for LT and MO materials (p < 0.001). Surface hardness and modulus were similar between control and S-treated specimens for all materials analyzed. XPS analysis showed homogeneous silica content after 20 and 40 RT-ALD cycles, and SEM did not show significant changes in surface morphology between C and S-treated specimens. CONCLUSION: RT-ALD resulted in effective silica deposition without any deleterious effect on zirconia-based materials mechanical properties. Alumina blasting promoted higher alteration on surface topography. HT prior to S resulted in superior FL (for MO and MT) and flexural strength (MO) for some of the materials investigated.