RESUMO
STATEMENT OF PROBLEM: The efficiency of adding nanoparticles to silicone protection has proven to prevent color degradation. However, reports of other physical property changes in facial silicone are scarce. PURPOSE: The purpose of this in vitro study was to evaluate the influence of adding nanoparticles on the hardness, tear strength, and permanent deformation of a facial silicone. MATERIAL AND METHODS: Specimens were made for each test, with 140 for the hardness test, 140 for the permanent deformation test, but 280 for the rupture test. This higher number was due to the fact that the first 140 specimens were ruptured and unusable after the initial reading. ZnO, BaSO4, and TiO2 nanoparticles at concentrations of 1% and 2% of silicone were used, as well as specimens without nanoparticles that consisted of only oil paint and of only silicone. Outcomes were measured before and after 1008 hours of accelerated aging. Data were analyzed by nested analysis of variance (ANOVA) and Tukey honest significant differences test (α=.05). RESULTS: Results showed that the presence of nanoparticles influenced the properties of the assessed groups. The nanoparticles decreased hardness values. The highest values of tear strength were observed for the groups with addition of BaSO4. The 1% ZnO group without oil paint showed the lowest values of permanent deformation. CONCLUSIONS: Based on the findings of this in vitro study, the use of ZnO nanoparticles is recommended, since they did not negatively affect the properties of the materials evaluated.
Assuntos
Prótese Maxilofacial , Análise de Falha de Equipamento , Dureza , Humanos , Prótese Maxilofacial/normas , Microscopia Eletroquímica de Varredura , Nanopartículas , Falha de Prótese , Resistência à Tração , Óxido de Zinco/uso terapêuticoRESUMO
The purpose of this literature review was to describe the main features of phantom eye syndrome in relation to their possible causes, symptoms, treatments, and influence of eye amputation on quality of life of anophthalmic patients. For this, a bibliographical research was performed in Pubmed database using the following terms: "eye amputation," "eye trauma," "phantom eye syndrome," "phantom pain," and "quality of life," associated or not. Thirteen studies were selected, besides some relevant references contained in the selected manuscripts and other studies hallowed in the literature. Thus, 56 articles were included in this review. The phantom eye syndrome is defined as any sensation reported by the patient with anophthalmia, originated anophthalmic cavity. In phantom eye syndrome, at least one of these three symptoms has to be present: phantom vision, phantom pain, and phantom sensations. This syndrome has a direct influence on the quality of life of the patients, and psychological support is recommended before and after the amputation of the eyeball as well as aid in the treatment of the syndrome. Therefore, it is suggested that, for more effective treatment of phantom eye syndrome, drug therapy should be associated with psychological approach.
Assuntos
Olho/patologia , Membro Fantasma/patologia , Humanos , Membro Fantasma/tratamento farmacológico , Sensação , SíndromeRESUMO
OBJECTIVES: The purpose of this study was to investigate the effect of thermal cycling and disinfection on the colour change of denture base acrylic resin. MATERIALS AND METHODS: Four different brands of acrylic resins were evaluated (Onda Cryl, QC 20, Classico and Lucitone). All brands were divided into four groups (n = 7) determined according to the disinfection procedure (microwave, Efferdent, 4% chlorhexidine or 1% hypochlorite). The treatments were conducted three times a week for 60 days. All specimens were thermal cycled between 5 and 55°C with 30-s dwell times for 1000 cycles before and after disinfection. The specimens' colour was measured with a spectrophotometer using the CIE L*a*b* system. The evaluations were conducted at baseline (B), after first thermal cycling (T1 ), after disinfection (D) and after second thermal cycling (T2 ). Colour differences (ΔE) were calculated between T1 and B (T1 B), D and B (DB), and T2 and B (T2 B) time-points. RESULTS: The samples submitted to disinfection by microwave and Efferdent exhibited the highest values of colour change. There were significant differences on colour change between the time-points, except for the Lucitone acrylic resin. CONCLUSIONS: The thermal cycling and disinfection procedures significantly affected the colour stability of the samples. However, all values obtained for the acrylic resins are within acceptable clinical parameters.