RESUMEN

Although deterioration of silicone maxillofacial prostheses is severely accentuated in smoking patients, the phenomenon has not been systematically studied. To address a gap in the literature concerning the stability of maxillofacial prostheses during service, in this contribution, the effect of cigarette smoke on the aspect and physical properties of M511 silicone elastomer was evaluated. The aspect, surface, and overall properties of the silicone material, pigmented or not, were followed by AFM, color measurements, FTIR, water contact angle measurements, TGA-DTG and DSC, hardness and compression stress-strain measurements. The types of the contaminants adsorbed were assessed by XRF, ESI-MS, MALDI-MS, and NMR spectral analyses. Important modifications in color, contact angle, surface roughness, local mechanical properties, and thermal properties were found in the silicone material for maxillofacial prostheses after exposure to cigarettes smoke. The presence of lead, nicotine, and several other organic compounds adsorbed into the silicone material was emphasized. Slight decrease in hardness and increase in Young's modulus was found. The combined data show important impact of cigarette smoke on the silicone physical properties and could indicate chemical transformations by secondary cross-linking. To our knowledge, this is the first study making use of complementary physical methods to assess the effect of cigarette smoke on the aspect and integrity of silicone materials for maxillofacial prostheses.

Asunto(s)

Ensayo de Materiales , Prótesis Maxilofacial , Humo , Humanos , Elastómeros de Silicona/química , Nicotiana/química , Color

RESUMEN

BACKGROUND: Digitally fabricated dentures may require relining due to continual alveolar ridge resorption. However, studies evaluating the tensile bond strength (TBS) of digitally fabricated dentures bonded to denture liners are lacking. This study aimed to evaluate the TBS of autopolymerized, heat-polymerized, milled, and 3D printed denture base materials bonded to 2 acrylic-based and 2 silicone-based denture liners, both before and after thermocycling. Additionally, the impact of thermocycling on the TBS were also evaluated. METHODS: The TBS of 4 different denture base materials (Palapress (PL), Vertex Rapid Simplified (VR), Smile CAM total prosthesis (SC), and NextDent denture 3D+ (ND)) bonded to 2 acrylic-based (GC Soft-Liner (GC) and Tokuyama Rebase II (RB)) and 2 silicone-based (Ufi Gel P (UP) and Sofreliner Tough M (ST)) denture liners were tested. Specimens (n = 8) were divided into non-thermocycling and thermocycling groups. Non-thermocycling specimens were tested after 24-hours water immersion, while thermocycling specimens were underwent 5000 cycle and were immediately tested. Mode of failure was examined under a stereomicroscope. Data were analyzed using 2-way ANOVA and Tukey HSD tests (α = 0.05), and independent samples t test (α = 0.05) for TBS between non-thermocycling and thermocycling groups. RESULTS: For the non-thermocycling groups, within the same denture liner material, no significant differences were found between denture base materials, except the ND + RB group, which had significantly lower TBS. For the thermocycling groups, within the same denture liner material, the TBS in the PL group exhibited the highest and the ND group exhibited the lowest. Within the same denture base material, in both non-thermocycling and thermocycling groups, the TBS in the ST group exhibited the highest; in contrast, that in the GC group exhibited the lowest. No significant differences were observed in TBS between non-thermocycling and thermocycling groups, except for denture base materials bonded to the ST group, SC + UP, and ND + UP groups. CONCLUSIONS: Milled denture base can be relined with acrylic-based or silicone-based denture liner. However, cautions should be exercised when relining 3D printed denture base. Thermocycling did not affect TBS between acrylic-based denture liners and denture bases. In contrast, it affected the bond between silicone-based denture liner and denture base.

Asunto(s)

Bases para Dentadura , Alineadores Dentales , Ensayo de Materiales , Impresión Tridimensional , Resistencia a la Tracción , Resinas Acrílicas/química , Recubrimiento Dental Adhesivo/métodos , Humanos , Polimerizacion , Materiales Dentales/química , Técnicas In Vitro , Calor , Análisis del Estrés Dental , Polimetil Metacrilato/química , Siliconas/química , Elastómeros de Silicona/química

RESUMEN

BACKGROUND: Glaucoma is one of the major irreversible blinding eye diseases in the world. Reducing intraocular pressure (IOP) is the primary treatment option, and taking eye drops daily is the common method. However, short drug duration and poor bioavailability of eye drops may lead to unsatisfied therapeutic effects and inadequate patient compliance. METHODS: A brimonidine-loaded silicone rubber insert (BRI@SR@PT) was prepared by loading brimonidine into a surface-modified silicone rubber ring, followed by polydopamine/thermoplastic polyurethane coatings. The physical properties, in vitro cytocompatibility and drug release of BRI@SR@PT were investigated. The BRI@SR@PT was administrated in the conjunctival sac of rabbit eyes, and its in vivo drug release, IOP-lowering efficacy and biosafety were assessed. RESULTS: The BRI@SR@PT presented great thermal stability and excellent elasticity. The BRI@SR@PT was able to release BRI sustainably for 28 days with little toxicity in vitro. Compared to BRI eye drops, the BRI@SR@PT effectively lowered IOP for 21 days based on the sustained BRI release with great biosafety when administrated in conjunctival sac of rabbit eyes in a noninvasive fashion. CONCLUSIONS: The conjunctival sac insert (BRI@SR@PT), as a promising drug-delivery platform, may provide a sustained IOP-lowering treatment for patients with ocular hypertension or glaucoma, without the need for invasive procedures.

Asunto(s)

Tartrato de Brimonidina , Preparaciones de Acción Retardada , Liberación de Fármacos , Glaucoma , Presión Intraocular , Poliuretanos , Conejos , Animales , Presión Intraocular/efectos de los fármacos , Glaucoma/tratamiento farmacológico , Tartrato de Brimonidina/administración & dosificación , Tartrato de Brimonidina/farmacología , Tartrato de Brimonidina/uso terapéutico , Poliuretanos/química , Poliuretanos/administración & dosificación , Sistemas de Liberación de Medicamentos , Polímeros/química , Elastómeros de Silicona/química , Conjuntiva , Soluciones Oftálmicas/administración & dosificación , Indoles/administración & dosificación , Indoles/farmacocinética , Masculino , Disponibilidad Biológica , Humanos , Antihipertensivos/administración & dosificación , Antihipertensivos/farmacología , Antihipertensivos/farmacocinética , Antihipertensivos/química

RESUMEN

Gesture recognition is crucial for enhancing human-computer interaction and is particularly pivotal in rehabilitation contexts, aiding individuals recovering from physical impairments and significantly improving their mobility and interactive capabilities. However, current wearable hand gesture recognition approaches are often limited in detection performance, wearability, and generalization. We thus introduce EchoGest, a novel hand gesture recognition system based on soft, stretchable, transparent artificial skin with integrated ultrasonic waveguides. Our presented system is the first to use soft ultrasonic waveguides for hand gesture recognition. EcoflexTM 00-31 and EcoflexTM 00-45 Near ClearTM silicone elastomers were employed to fabricate the artificial skin and ultrasonic waveguides, while 0.1 mm diameter silver-plated copper wires connected the transducers in the waveguides to the electrical system. The wires are enclosed within an additional elastomer layer, achieving a sensing skin with a total thickness of around 500 µ m. Ten participants wore the EchoGest system and performed static hand gestures from two gesture sets: 8 daily life gestures and 10 American Sign Language (ASL) digits 0-9. Leave-One-Subject-Out Cross-Validation analysis demonstrated accuracies of 91.13% for daily life gestures and 88.5% for ASL gestures. The EchoGest system has significant potential in rehabilitation, particularly for tracking and evaluating hand mobility, which could substantially reduce the workload of therapists in both clinical and home-based settings. Integrating this technology could revolutionize hand gesture recognition applications, from real-time sign language translation to innovative rehabilitation techniques.

Asunto(s)

Gestos , Mano , Reconocimiento de Normas Patrones Automatizadas , Dispositivos Electrónicos Vestibles , Humanos , Femenino , Mano/fisiología , Adulto , Masculino , Reconocimiento de Normas Patrones Automatizadas/métodos , Adulto Joven , Ultrasonido , Algoritmos , Elastómeros de Silicona , Piel , Reproducibilidad de los Resultados

RESUMEN

The occurrence and ecological impacts of emerging fungicides in the environment has gained increasing attention. This study applied an in-jar passive sampling device based on silicone rubber (SR) film to measuring the freely dissolved concentration (Cfree) of 6 current-use fungicides as a critical index of bioavailability in water and soils. The kinetics parameters including SR-water, soil-water, and organic carbon-water partition coefficients and sampling rates of the target fungicides were first attained and characterized well with their physicochemical properties. The in situ and ex situ field deployment in Hefei City provided the assessment of contaminated levels for these fungicides in rivers and soils. The Cfree of triadimefon and azoxystrobin was estimated at 0.54 ± 0.07-17.4 ± 2.5 ng L-1 in Nanfei River and Chao Lake, while triadimefon was only found in Dongpu Reservoir water with Cfree below 0.66 ± 0.04 ng L-1. The results exhibited that the equilibrium duration of 7 d was suitable for water application but a longer interval of 14 d was recommended for soil sampling. This work demonstrated the advantages of the proposed strategy in terms of fast monitoring within 2 weeks and high sensitivity down to detection limits in 0.5-5 ng L-1. The in-jar passive sampling device can be extrapolated to the evaluation for a wide coverage of organic pollutants in water and soils.

Asunto(s)

Monitoreo del Ambiente , Fungicidas Industriales , Elastómeros de Silicona , Contaminantes del Suelo , Suelo , Contaminantes Químicos del Agua , Fungicidas Industriales/análisis , Monitoreo del Ambiente/métodos , Contaminantes Químicos del Agua/análisis , Contaminantes del Suelo/análisis , Suelo/química , China , Ríos/química

RESUMEN

Blood-contacting catheters play a pivotal role in contemporary medical treatments, particularly in the management of cardiovascular diseases. However, these catheters exhibit inappropriate wettability and lack antimicrobial characteristics, which often lead to catheter-related infections and thrombosis. Therefore, there is an urgent need for blood contact catheters with antimicrobial and anticoagulant properties. In this study, we employed tannic acid (TA) and 3-aminopropyltriethoxysilane (APTES) to create a stable hydrophilic coating under mild conditions. Heparin (Hep) and poly(lysine) (PL) were then modified on the TA-APTES coating surface using the layer-by-layer (LBL) technique to create a superhydrophilic TA/APTES/(LBL)4 coating on silicone rubber (SR) catheters. Leveraging the superhydrophilic nature of this coating, it can be effectively applied to blood-contacting catheters to impart antibacterial, antiprotein adsorption, and anticoagulant properties. Due to Hep's anticoagulant attributes, the activated partial thromboplastin time and thrombin time tests conducted on SR/TA-APTES/(LBL)4 catheters revealed remarkable extensions of 276 and 103%, respectively, when compared to uncoated commercial SR catheters. Furthermore, the synergistic interaction between PL and TA serves to enhance the resistance of SR/TA-APTES/(LBL)4 catheters against bacterial adherence, reducing it by up to 99.9% compared to uncoated commercial SR catheters. Remarkably, the SR/TA-APTES/(LBL)4 catheter exhibits good biocompatibility with human umbilical vein endothelial cells in culture, positioning it as a promising solution to address the current challenges associated with blood-contact catheters.

Asunto(s)

Catéteres , Materiales Biocompatibles Revestidos , Heparina , Polifenoles , Taninos , Materiales Biocompatibles Revestidos/química , Materiales Biocompatibles Revestidos/farmacología , Humanos , Catéteres/microbiología , Polifenoles/química , Polifenoles/farmacología , Heparina/química , Heparina/farmacología , Taninos/química , Taninos/farmacología , Silanos/química , Silanos/farmacología , Anticoagulantes/química , Anticoagulantes/farmacología , Propilaminas/química , Aminas/química , Aminas/farmacología , Antibacterianos/farmacología , Antibacterianos/química , Polilisina/química , Polilisina/farmacología , Propiedades de Superficie , Interacciones Hidrofóbicas e Hidrofílicas , Células Endoteliales de la Vena Umbilical Humana/efectos de los fármacos , Elastómeros de Silicona/química , Adsorción , Escherichia coli/efectos de los fármacos

RESUMEN

STATEMENT OF PROBLEM: The choice of cleaning method is an important consideration for lengthening the serviceable time of facial prostheses as microbial organisms and biofilms could degrade facial prostheses and cause skin irritation. Whether microwave disinfection is a suitable cleaning method without degradation of the properties of a prosthesis is unclear. PURPOSE: The purpose of this in vitro study was to measure the color stability of 6 commonly used facial silicone elastomers after microwave disinfection over a simulated 1.5-year period. MATERIAL AND METHODS: Six different facial silicone elastomers: MDX4-4210, MDX4-4210/Type A, M511, A-2186, VST-50, and A-2000 were mixed with intrinsic silicone white opacifier (except for the control group) and subsequently combined with 4 silicone intrinsic pigment color groups: red (R), yellow (Y), burnt sienna (B), and a mixture of R+Y+B (M). The control group was a silicone elastomer without opacifier or pigment. Each of the 30 experimental groups consisted of 5 specimens (N=150). Five specimens were placed in a 250-mL Erlenmeyer flask filled with 160 mL of tap water. Seven flasks were then placed in a 660-W microwave oven. An exposure of 6 minutes was used according to the antimicrobial efficacy of microwave disinfection protocol on facial silicone prostheses with a final water temperature of 60 °C for 18 times (simulating 1.5 years of microwave disinfection with one 6-minute exposure monthly). A spectrophotometer was used to measure reflectance color change values (∆E). Color differences were calculated following CIELab (∆E*ab) and CIEDE2000 (∆E00) formulae. ∆E*ab and ∆E00 were statistically analyzed by a linear mixed effects model with 3 factors (silicone type, color shade, and time) using the R Statistical software program (α=.05). RESULTS: Both ∆E*ab and ∆E00 of all silicone elastomers studied were less than the visual perceptibility thresholds (∆E*ab<1.1 and E00<0.7) and were considered clinically acceptable (∆E*ab<3.0 and E00<2.1) after the 1.5-year simulation of microwave disinfection. Yellow and blue pigments had more effect on MDX4-4210 and M511, while red pigment had more effect on MDX4-4210, MDX4-4210/Type A, and M511 (P<.05). Nevertheless, the values were still below the perceptibility threshold (∆E*ab≤1.0 and E00<0.6). CONCLUSIONS: All 6 facial silicone elastomers maintained clinically acceptable color after 18 months of exposure to microwave disinfection.

Asunto(s)

Color , Desinfección , Prótesis Maxilofacial , Microondas , Elastómeros de Silicona , Microondas/uso terapéutico , Desinfección/métodos , Elastómeros de Silicona/química , Coloración de Prótesis , Humanos , Técnicas In Vitro , Ensayo de Materiales , Dimetilpolisiloxanos

RESUMEN

PURPOSE: To evaluate flow profile and non-Newtonian behavior of 10 different silicone lining materials. METHODS: Ten commercially available silicone lining materials were selected for evaluation. The flow profile and non-Newtonian behavior of each material was measured using a shark fin testing method. Fin height and resultant base thickness were measured with a digital caliper and compared with one-way ANOVA and Student-Newman-Keuls post hoc test and fin base by Kruskal-Wallis one-way ANOVA on ranks with Dunn post hoc test with significance at P< 0.05 for both. RESULTS: Shark fin heights ranged from 9.62 ± 0.86 mm [Reline II (Soft)] to 25.54 ± 0.43 mm [Sofreliner (Medium)]. Shark fin bases ranged from 2.57 ± 0.51 mm [Sofreliner (Medium)] to 10.31 ± 0.57 mm [Reline II (Soft)]. Statistically significant differences were found between certain samples' shark fin heights as well as resultant bases (P< 0.05) indicating different rheological properties. CLINICAL SIGNIFICANCE: Silicone liner materials differ significantly with respect to flow profile and non-Newtonian behavior. While a high flow profile (low viscosity) of an elastomeric impression material improves accuracy, it may be a detriment to a denture lining material that must achieve a critical minimum thickness to provide resilience. Likewise, a low flow profile (high viscosity) material may also pose a disadvantage, requiring excessive compression and possible tissue distortion to achieve the same critical thickness. The results of this study should be considered when selecting the appropriate material for clinical application. Additional studies are indicated to further quantify rheological properties as well as correlate them to physical properties after the complete cure of the material.

Asunto(s)

Alineadores Dentales , Siliconas , Humanos , Viscosidad , Ensayo de Materiales , Bases para Dentadura , Elastómeros de Silicona , Propiedades de Superficie

RESUMEN

PURPOSE: This study investigated the color stability of different commercially available silicone materials for facial prostheses upon exposure to everyday beverages. It was hypothesized that the beverages would not alter the color of the silicone under conditions simulating daily exposure. METHODS: Sixty specimens were fabricated using two materials - VST-50 and Silfy - and exposed to commercially available cold mineral water, tea, or coffee. Specimen color was evaluated on days 1 and 15. The color was measured with a spectrophotometer based on CIELab system and color differences were calculated as ΔE. Statistical analysis was performed using the Kruskal-Wallis test and Mann-Whitney U test. RESULTS: The mean ΔE values after 15 days of exposure to mineral water, cold green tea, and coffee were 1.016, 3.480, and 3.636 for VST-50 and 0.440, 0.798, and 1.425 for Silfy, respectively. Both materials showed significant differences in color, and VST-50 showed a greater color change than Silfy, especially for coffee. CONCLUSION: Pigmented silicone elastomers have low color stability, leading to an overall color change in silicone prostheses when exposed to pigmented beverages. Color changes in such prostheses can be mitigated by selecting materials with better color stability to extend their longevity.

Asunto(s)

Prótesis Maxilofacial , Aguas Minerales , Elastómeros de Silicona , Color , Café , Coloración de Prótesis , Ensayo de Materiales , Bebidas

RESUMEN

During the disinfection of indoor spaces using gaseous hypochlorous acid (HOCl(g)), inhalation is the most common route of exposure for humans. In this study, an artificial human respiratory tract model was exposed to 12-140 ppb HOCl(g) at an aspiration flow rate of 800 mL/s for 15 h in a 1 m3 chamber. The respiratory tract model was equipped with 5th order bronchi and all gas-contact parts were made of silicone rubber with no other chlorine-consuming substances. The concentration of HOCl(g) reaching the lung pseudo-space was approximately 47.4% of the HOCl(g) concentrations in the chamber and was calculated to be very close to zero when the chamber concentration was less than 20.5 ppb. The disappearance of HOCl(g) during inhalation is likely due to the adsorption of HOCl(g) on the gas-contact silicone rubber surfaces. The cytotoxicity of HOCl(g) on respiratory epithelial cells was also examined using human air-liquid-interface airway tissue models. Human nasal epithelium and bronchiolar epithelium were exposed to 100 ppb and 500 ppb HOCl(g) for 8 h and 5 d, respectively. No significant effects of HOCl(g) on cell viability and ciliary activity were observed in any cell type, indicating that low concentrations of HOCl(g）, less than 500 ppb, had no cytotoxic effect.

Asunto(s)

Gases , Ácido Hipocloroso , Humanos , Ácido Hipocloroso/farmacología , Elastómeros de Silicona , Células Epiteliales , Pulmón

RESUMEN

PURPOSE: To evaluate the clinical profile of myopic strabismus fixus (MSF) in children and surgical outcomes of silicone band loop myopexy. METHOD: We retrospectively reviewed records of children presenting with MSF who underwent silicone band loop myopexy between January 2008 and December 2020 at a tertiary eye care center. Data concerning demographics, refractive error, axial length, extra-ocular motility, and ocular alignment pre-operatively and post-operatively, intra- and post-operative complications, ocular and systemic associations, were evaluated. The long-term effects of band loop myopexy on ocular alignment stability, motility improvement, and myopia progression were analyzed. Surgical outcome was defined as post-operative orthotropia or heterotropia less than or equal to 20 PD. RESULTS: A total of0 eyes of 7 patients (median age: 5 years; 5 boys and 2 girls) who underwent band loop myopexy were included in the study. Among them, three children underwent bilateral and four children underwent unilateral band loop myopexy. Medial rectus recession was performed only in two patients as a part of initial procedure. The median follow-up duration was 7 years. Most of the children, i.e. six of them presented with esotropia-hypotropia and only one patient presented with exotropia-hypotropia complex. The median pre-operative measurements were esotropia of 62.5 PD, hypotropia of5 PD, and exotropia of4 PD. Postoperative average primary position deviation measured was close to 9-10 PD of esotropia. The overall motility improved to -1 from -3. CONCLUSION: The clinical profile of MSF in children is almost similar to adults. This condition is a rare entity among adults as well as children. Majority of children with MSF presented with esotropia-hypotropia complex. Silicone band loop myopexy with or without medial rectus recession proves to be a reliable surgical procedure as it provides stable outcomes in terms of ocular alignment and motility among children.

Asunto(s)

Miopía , Músculos Oculomotores , Procedimientos Quirúrgicos Oftalmológicos , Humanos , Masculino , Femenino , Estudios Retrospectivos , Músculos Oculomotores/cirugía , Músculos Oculomotores/fisiopatología , Niño , Miopía/cirugía , Miopía/fisiopatología , Miopía/complicaciones , Preescolar , Procedimientos Quirúrgicos Oftalmológicos/métodos , Resultado del Tratamiento , Visión Binocular/fisiología , Movimientos Oculares/fisiología , Estudios de Seguimiento , Agudeza Visual/fisiología , Elastómeros de Silicona , Estrabismo/cirugía , Estrabismo/fisiopatología , Estrabismo/etiología , Refracción Ocular/fisiología

RESUMEN

1,3-dichlorobenzene (1,3-DCB) is an aromatic solvent that might be formed during thermal decomposition of bis(2,4-dichlorobenzoyl)peroxide used as initiator in silicone rubber production with many workers exposed worldwide. During metabolism of 1,3-DCB, two isomeric mercapturic acids can be formed from ring oxidation of 1,3-DCB in the liver, namely 2,4-dichlorophenylmercapturic acid (24CPhMA) and 3,5-dichlorophenylmercapturic acid (35CPhMA). These urinary mercapturic acids might serve as biomarkers of the toxicologically relevant absorbed dose of 1,3-DCB and have not been determined so far. Thus, we were aimed to develop an analytical method for quantification of these biomarkers. Authentic standards of both mercapturic acids as well as deuterium-labelled analogues were self-synthesized. A method for the quantification of both CPhMAs in human urine using online-SPE LC/MS/MS was developed and validated with an LOQ of 0.1 ng mL-1 for both CPhMAs. The analytes were extracted from urine by online-SPE on a restricted access material phase, transferred to the analytical column and quantified by tandem mass spectrometry. Interday (n = 6) and Intraday (n = 10) precision for both CPhMAs ranged from 1.7 to 4.3 % with accuracies between 99.4 and 109.9 % at concentrations of 0.6 and 3 ng mL-1. We applied the method on post-shift urine samples of 16 workers of the silicone rubber industry with occupational exposure to 1,3-DCB. Both CPhMAs were above LOQ in 15 of 16 urine samples with median levels (range) for 24CPhMA and 35CPhMA of 1.64 ng mL-1 (<0.1 - 8.2 ng mL-1) and 3.98 ng mL-1 (0.36 - 24.1 ng mL-1), respectively. This is the first report on specific urinary mercapturic acids of 1,3-DCB in humans. Our results show that ring oxidation of 1,3-DCB is considered to be a toxicologically relevant metabolic pathway in humans. This might improve risk assessment of 1,3-DCB-emissions in silicone rubber industry.

Asunto(s)

Clorobencenos , Cromatografía Líquida con Espectrometría de Masas , Espectrometría de Masas en Tándem , Humanos , Espectrometría de Masas en Tándem/métodos , Cromatografía Liquida/métodos , Acetilcisteína/química , Elastómeros de Silicona , Biomarcadores/orina , Isótopos

RESUMEN

Silicone rubber (SR), a common medical-grade polymer used in medical devices, has previously been modified for nitric oxide (NO) releasing capabilities. However, the effects of material properties such as film thickness on NO release kinetics are not well explored. In this study, SR is used in the first analysis of how a polymer's thickness affects the storage and uptake of an NO donor and subsequent release properties. Observed NO release trends show that a polymer's thickness results in tunable NO release. These results indicate how crucial a polymer's thickness is to optimize the NO release in an efficient and effective method.

Asunto(s)

Óxido Nítrico , Elastómeros de Silicona , Donantes de Óxido Nítrico

RESUMEN

Objective: To investigate the dosimetric effects of using individualized silicone rubber (SR) bolus on the target area and organs at risk (OARs) during postmastectomy radiotherapy (PMRT), as well as evaluate skin acute radiation dermatitis (ARD). Methods: A retrospective study was performed on 30 patients with breast cancer. Each patient was prepared with an individualized SR bolus of 3 mm thickness. Fan-beam computed tomography (FBCT) was performed at the first and second fractions, and then once a week for a total of 5 times. Dosimetric metrics such as homogeneity index (HI), conformity index (CI), skin dose (SD), and OARs including the heart, lungs, and spinal cord were compared between the original plan and the FBCTs. The acute side effects were recorded. Results: In targets' dosimetric metrics, there were no significant differences in Dmean and V105% between planning computed tomography (CT) and actual treatments (P > .05), while the differences in D95%, V95%, HI, and CI were statistically significant (P < .05). In OARs, there were no significant differences between the Dmean, V5, and V20 of the affected lung, V5 of the heart and Dmax of the spinal cord (P > .05) except the V30 of affected lung, which was slightly lower than the planning CT (P < .05). In SD, both Dmax and Dmean in actual treatments were increased than plan A, and the difference was statistically significant (P < .05), while the skin-V20 and skin-V30 has no difference. Among the 30 patients, only one patient had no skin ARD, and 5 patients developed ARD of grade 2, while the remaining 24 patients were grade 1. Conclusion: The OR bolus showed good anastomoses and high interfraction reproducibility with the chest wall, and did not cause deformation during irradiation. It ensured accurate dose delivery of the target and OARs during the treatment, which may increase SD by over 101%. In this study, no cases of grade 3 skin ARD were observed. However, the potential of using OR bolus to reduce grade 1 and 2 skin ARD warrants further investigation with a larger sample size.

Asunto(s)

Neoplasias de la Mama , Dermatitis , Radioterapia de Intensidad Modulada , Humanos , Femenino , Neoplasias de la Mama/radioterapia , Neoplasias de la Mama/cirugía , Elastómeros de Silicona , Planificación de la Radioterapia Asistida por Computador/métodos , Dosificación Radioterapéutica , Estudios Retrospectivos , Reproducibilidad de los Resultados , Mastectomía/efectos adversos , Radioterapia de Intensidad Modulada/efectos adversos , Radioterapia de Intensidad Modulada/métodos , Tomografía Computarizada por Rayos X , Dermatitis/cirugía , Órganos en Riesgo/efectos de la radiación

RESUMEN

STATEMENT OF PROBLEM: Part 1 of this 2-part study determined that microwave disinfection did not degrade the color stability of facial silicone prostheses. However, investigations on the effects of microwave disinfection on the mechanical properties of different silicone elastomers are lacking. PURPOSE: The purpose of this in vitro study was to examine the mechanical properties of commonly used colored facial silicone elastomers before and after microwave disinfection over a simulated 1.5-year period. MATERIAL AND METHODS: Six commonly used facial silicone elastomers: MDX4-4210, MDX4-4210/Type A, M511, A-2186, VST-50, and A-2000 were combined with functional intrinsic silicone pigments and opacifier (red, yellow, blue, and white). A total of 288 specimens were fabricated (n=12). Half of the specimens were tested for mechanical properties as the baseline, while the other specimens were tested after microwave disinfection. Microwave disinfection was performed with 660 W, 6 minutes of exposure time, and microwaved for 18 cycles to simulate 1.5 years of usage (one 6-minute exposure monthly). For mechanical property testing, all specimens were tested for tensile strength and percentage elongation (ASTM D412), tear strength (ASTM D624), and hardness (ASTM D2240). For each property, a 2-way ANOVA (silicone type and microwave disinfection factors) and Tukey multiple comparison test were performed using the R statistical software program (α=.05). RESULTS: Following microwave disinfection, tensile strength and percentage elongation of A-2000 increased significantly (P<.05). MDX4-4210, MDX4-4210/Type A, and A-2000 showed significant increases in their hardness (P<.001). Tear strength also increased significantly for MDX4-4210 and VST-50 (P<.05). Among the materials tested (ranked from highest to lowest value,=not statistically significant different), for tensile strength, VST-50>A-2186=A-2000>MDX4-4210/Type A=M511=MDX4-4210 (P<.05). For percentage elongation, VST-50>MDX4-4210/Type A>A-2186>M511=A-2000=MDX4-4210=M511 (P<.05). For hardness, A-2000=A-2186>M511=VST-50>MDX4-4210>MDX4-4210/Type A (P<.05). For tear strength, VST-50>A-2186>A-2000>M511>MDX4-4210/Type A=MDX4-4210 (P<.05). CONCLUSIONS: Overall, the mechanical properties of all the silicones tested were not adversely affected by microwave disinfection. VST-50 showed the best mechanical properties among the materials tested both before and after microwave disinfection. Microwave energy is a safe method of disinfecting the silicone elastomers tested in this study.

Asunto(s)

Implantes Dentales , Dimetilpolisiloxanos , Prótesis Maxilofacial , Elastómeros de Silicona , Desinfección , Ensayo de Materiales , Microondas/uso terapéutico , Resistencia a la Tracción

RESUMEN

BACKGROUND: Urethral injury occurs in 1-6 % of male cases during minimally invasive surgery of lower rectal cancer. A Foley catheter emitting near-infrared (NIR) fluorescence of sufficient intensity has been expected to locate the urethra during image-guided surgery. Although it has been difficult to impart NIR fluorescent properties to biocompatible thermosetting polymers, we have recently succeeded in developing a NIR fluorescent compound for silicone rubber and a NIR fluorescent Foley catheter (HICARL). Here, we evaluated its NIR fluorescence properties and visibility performance using porcine anorectal isolation specimens. METHODS: The HICARL catheter was made of a mixture of solid silicone rubber and a NIR fluorescent compound that emits fluorescence with a wavelength of 820-880 nm, while a conventional transparent Foley catheter was made of solid silicone rubber only. As a standard for comparison of the intensity of NIR fluorescence, a transparent Foley catheter the lumen of which was filled with a mixture of indocyanine green (ICG) and human plasma was used. As a comparison to assess the visibility performance of the HICARL catheter, a transparent Foley catheter into which a commercially available NIR fluorescent polyurethane ureteral catheter (NIRC) was placed was used. RESULTS: A NIR fluorescence quantitative imaging analysis revealed that the Foley-NIRC catheter and the HICARL catheter emitted 3.42 ± 0.42 and 6.43 ± 0.07 times more fluorescence than the Foley-ICG catheter, respectively. The location of the HICARL catheter placed in the anorectum with a wall thickness of 3.8 ± 0.1 mm was clearly delineated in its entirety by NIR fluorescence, while that of the Foley-NIRC catheter was faintly or only partially visible. CONCLUSIONS: The HICARL catheter emitting NIR fluorescence of sufficient intensity is a promising and easy-to-use tool for urethral visualization during image-guided surgery of lower rectal cancer.

Asunto(s)

Fotoquimioterapia , Neoplasias del Recto , Cirugía Asistida por Computador , Humanos , Masculino , Animales , Porcinos , Elastómeros de Silicona , Fotoquimioterapia/métodos , Fármacos Fotosensibilizantes , Colorantes , Verde de Indocianina/farmacología , Catéteres , Neoplasias del Recto/diagnóstico por imagen , Neoplasias del Recto/cirugía

RESUMEN

PURPOSE: To assess the complications that resulted in the explantation or secondary intervention with foldable intraocular lenses (IOLs). SETTING: University setting, Salt Lake City, Utah. DESIGN: Survey study. METHODS: For the 25th consecutive year, surgeons were surveyed regarding complications associated with foldable IOLs requiring explantation or secondary intervention over the 2022 calendar year. These forms were made available online using the ASCRS and ESCRS websites and a fax-on-demand service. Surgeons completed 1 survey for each foldable IOL requiring explantation or secondary intervention. Further analysis determined complication trends related to specific IOL styles, materials, and types over the past 16 years (2007 to 2022). RESULTS: 103 completed surveys were returned in 2022 contributing to a total of 1627 tabulated surveys since 2007. In the 2022 survey, dislocation/decentration continued to be the most common complication overall. Glare/optical aberrations was a common complication associated with multifocal IOLs continuing a 16-year trend. In addition, hydrophilic acrylic IOLs as well as some silicone lenses in eyes with asteroid hyalosis demonstrated calcification as the most common complication necessitating explantation. CONCLUSIONS: Dislocation/decentration remains the leading cause of explantation in most IOL types. Glare/optical aberrations continue to be an associated complication of multifocal IOLs suggesting this ongoing issue has yet to be resolved with this type of IOL. In addition, calcification of hydrophilic acrylic lenses and silicone lenses is a rare event but continues to occur.

Asunto(s)

Lentes Intraoculares , Lentes Intraoculares Multifocales , Humanos , Lentes Intraoculares/efectos adversos , Encuestas y Cuestionarios , Siliconas , Remoción de Dispositivos , Elastómeros de Silicona

RESUMEN

PURPOSE: To evaluate the effect of adding tea tree oil to denture liners on Candida albicans and bond strength to the acrylic denture base. MATERIALS AND METHODS: Disc-shaped specimens were fabricated from silicone-based resilient liner (Tokuyama, Molloplast), acrylic-based hard liner (GC Reline), and acrylic-based soft liner (Visco-gel). Tea tree oil (TTO) was incorporated into the liners at varying concentrations (0% [control], 2%, 5%, 8%). C albicans were counted by viable colony count, and optical density (OD) was measured with a spectrophotometer. The tensile strength to heat polymerized acrylic denture base was measured in a universal testing machine. The compliance of the data to the distribution of normality was evaluated using the Shapiro Wilk test. Two-way ANOVA, Bonferroni correction, and paired sample t test were performed (α = .05). RESULTS: The addition of TTO into liners provided a significant decrease in the OD values (P < .001). The control groups of the liners presented the highest colony counts, whereas increasing TTO decreased the results (P < .01). According to tensile bond strength test, 8% TTO addition resulted in a significant decrease for Tokuyama (P < .01) and Molloplast liners (P < .05), while 2% TTO resulted in significance for GC Reline (P < .001). CONCLUSIONS: Denture liners containing increasing percentages of TTO presented lower amounts of C albicans colonies and decreased bond strength to the denture bases. When using TTO for its antifungal properties, the amount added should be carefully selected because the tensile bond strength may be affected.

Asunto(s)

Recubrimiento Dental Adhesivo , Alineadores Dentales , Aceite de Árbol de Té , Elastómeros de Silicona/química , Bases para Dentadura , Candida albicans , Aceite de Árbol de Té/farmacología , Resinas Acrílicas/química , Ensayo de Materiales , Polimetil Metacrilato , Resistencia a la Tracción

RESUMEN

Episil is a bioadhesive barrier-forming liquid gel that can relieve mucositis caused by radiotherapy (RT) and effectively relieve pain. The purpose of this trial is to compare the efficacy and safety of Episil in improving acute radiation dermatitis (ARD) in patients with breast cancer. This study included patients who met the criteria for postoperative RT for breast cancer. The primary end point was the grade of RD during treatment. A total of 102 patients were included in this study. The patients were grouped in a 2:1 ratio using the randomized number table method: 67 patients received Episil combined with conventional skin care (the Episil group), whereas the remaining 35 patients served as the control group and received conventional skin care only (the control group). According to the grading criteria of the Radiation Therapy Oncology Group (RTOG), the skin reaction rate and severity were significantly better in the Episil group than the control group (24.62%, 72.31%, 3.08, 0, 0 vs. 0, 85.71%, 14.29%, 0, 0, 0) across grades 0 to 4 (P < 0.05). The itchiness score exhibited s significant reduction in the Episil group as compared with the control group (P < 0.05). The results of the European Organization for Research and Treatment of Cancer Quality of Life Questionnaire (EORTC QLQ-C30) showed that the overall health (z = -5.855, P < 0.001) and overall quality of life (z = -6.583, P < 0.001) were better in the Episil group than the control group after RT. Overall, in patients with breast cancer receiving RT, the topical application of Episil may significantly reduce the grading of ARD, alleviate patient symptoms, and improve the patient's overall quality of life.

Asunto(s)

Neoplasias de la Mama , Radiodermatitis , Elastómeros de Silicona , Humanos , Femenino , Neoplasias de la Mama/radioterapia , Neoplasias de la Mama/cirugía , Calidad de Vida , Radiodermatitis/tratamiento farmacológico , Dolor

RESUMEN

Polymer modification using silicone rubber represents a promising avenue for enhancing physico-mechanical properties. However, achieving optimal performance through direct blending is hindered by the poor interface compatibility between silicone rubber and the matrix. In this study, we prepared super-tough thermoplastic vulcanizates (TPVs) of polylactic acid/silicone rubber through dynamic vulcanization with PLA, methyl vinyl silicone rubber (MVQ), glycidyl methacrylate grafted MVQ (MVQ-g-GMA), and fumed silica nanoparticles (SiO2). The impact of the SiO2 addition in MVQ on the morphology, mechanical properties, crystallization, and thermal properties of the TPVs was investigated. The results showed that MVQ-g-GMA and SiO2 exhibited a synergistic compatibilization effect significantly improving the interfacial adhesion between PLA and MVQ. Therefore, the impact and tensile strength of the TPVs increased from 8.0 kJ/m2 and 22.2 MPa to 62.6 kJ/m2 and 36.7 MPa, respectively. Moreover, the TPVs also presented good low-temperature toughness with a maximum impact strength of 40.4 kJ/m2 at -20 °C. Additionally, improvements in thermal stability and crystallization rate were also observed. Overall, combining organic and inorganic synergistic compatibilization is a feasible and effective method to fabricate outstanding low-temperature toughness to PLA.

Asunto(s)

Dióxido de Silicio , Elastómeros de Silicona , Poliésteres , Polímeros