RESUMEN

Objective The purpose of this study is to compare the tensile bond strength values to composite substrate pre- and post-aging between IPS E.max CAD and Initial LiSi. Methods The study utilized four blocks of IPS E.max CAD LT/B1 C14 (Ivoclar Vivadent, Liechtenstein, Germany) (referred to as E) and four blocks of Initial LiSi LT/B1 (GC, Tokyo, Japan) (referred to as L). These blocks were milled to produce 76 ceramic bars measuring 2 mm × 2 mm × 10 mm (E = 38, L = 38/n = 19). After acid etching with hydrofluoric acid (BISCO, Schaumburg, IL, USA) and silane application (BIS-SILANE, BISCO), the specimens were embedded in putty (Express STD, 3M, Decatur, AL, USA) to create a mold for the resin cement (RelyX U200, 3M). Subsequently, one group of each brand underwent mechanical tensile testing (E0 and L0), while the other groups were subject to tensile testing after artificial aging involving 500 thermal cycles between 5 and 55°C (E5 and L5). The mean tensile strength for each group (E0, E5, L0, and L5) was determined using the Brown-Forsythe one-way ANOVA and Tamhane's post hoc tests. Results Initial LiSi showed a superior pre-aging mean (11.7 MPa). However, both materials had identical post-aging means (7.6 MPa). There were no statistically significant differences, except between the dependent Initial LiSi groups (L0-L5). Most failure modes were mixed (cohesive cement and adhesive). There were no cohesive failures on the cement side except in three specimens of Initial LiSi post-aging. Conclusion The tested conditions have shown that Initial Lisi exhibited the highest pre-aging mean; however, it exhibited inferior bond stability under aging conditions compared to IPS E.max CAD. Analyzing the microstructure before and after aging may provide insights into the greater decrease in bond strength observed in the Initial LiSi specimens.

RESUMEN

Introduction A space between the prepared tooth and the cemented crown can cause microleakage, allowing microorganisms to enter, which in turn leads to the breakdown of the luting cement. To achieve an optimum fit, several factors should be considered, including the type of crown used, the taper of tooth preparation, and the type of cementing agent. Aim The purpose of the current study is to evaluate the microleakage of zirconia crowns cemented with glass ionomer cement (GIC), resin-modified GIC (RMGIC), and self-adhesive resin cement. Materials Forty-five primary mandibular molars were divided into three groups: Group I receiving GIC, Group II receiving RMGIC, and Group III receiving self-adhesive resin cement. These cements were used to lute the teeth with Kedo zirconia crowns. The restored samples underwent thermal cycling and were assessed for microleakage under a stereomicroscope. For the statistical analysis, SPSS version 23.0 was used. Descriptive statistics were presented as frequencies and percentages. Analytical statistics, including the Mann Whitney U test, were used to assess the differences in the level of microleakage between the groups at p < 0.05. Results The Mann Whitney U test revealed no significant difference in the level of microleakage between GIC and RMGIC (p = 0.072). However, self-adhesive resin cement showed significantly less microleakage than GIC (p = 0.000). Similarly, when comparing RMGIC and self-adhesive resin cement, the latter showed significantly less microleakage than the former (p = 0.001). Conclusion Microleakage of Kedo zirconia crowns on mandibular first molars was highest when luted with GIC, followed by RMGIC, and was least when luted with self-adhesive resin cement.

RESUMEN

Despite the rise in popularity of ceramic braces for adults, the risk of enamel microcracks (EMCs) upon removal remains a significant drawback for both dental professionals and patients. Our study aimed to assess the effects of thermocycling, pre-curing, and co-curing techniques with different bonding agents on the enamel surface of teeth after the removal of ceramic brackets. We also examined the incidence, quantity, length, and direction of EMCs on tooth surfaces. Additionally, the adhesive remnant index (ARI) scores and orthodontic bracket bond failure modes were evaluated and compared. The study divided 40 extracted upper canine teeth into ten groups for further analysis. Two groups had intact enamel as the negative control, while the remaining groups had orthodontic ceramic brackets bonded using different bonding agents and curing techniques. Thermocycling was performed in five groups, and ARI was assessed after debonding. The study findings were statistically significant (p < 0.05) in demonstrating the impact of curing techniques on EMCs and debonding outcomes. Seventh-generation bonding agents resulted in complete adhesive removal (ARI = 0). The microcracks' incidence, number, and length showed insignificant results. Differences in ARI between thermocycler and non-thermocycler samples were insignificant. Both co-curing and pre-curing techniques yielded comparable ARI results. This study highlights the importance of using advanced bonding agents to minimize enamel damage during ceramic bracket debonding.

RESUMEN

BACKGROUND: While many denture base materials are currently available on the market, little data exists regarding their dimensional stability after exposure to the oral environment. This study aimed to evaluate the effect of thermocycling on the trueness and precision of milled, 3-dimensional (3D)-printed, and conventional digitally fabricated complete denture bases (CDBs). METHODS: A completely edentulous maxillary stone model was scanned to generate a standard tessellation language (STL) file; this was imported into metal-milling-machine software (Redon Hybrid CAD-CAM metal milling machine, Redon, Turkey) to produce a metal model for fabricating 30 CDBs. These were divided into three groups (n = 10 in each) according to the construction technique: group 1, CAD-CAM milled CDBs; group 2, 3D-printed CDBs; and group 3, conventional compression molded CDBs. All CDBs were scanned after fabrication and evaluated before and after thermocycling using superimposition. The data were analyzed using a one-way ANOVA, Tukey's post hoc test, and a paired t-test. RESULTS: The level of trueness between the CAD-CAM milled, 3D-printed, and compression molded CDBs showed significant differences before and after thermocycling (P < 0.05). Group 1 showed the highest degree of trueness before and after thermocycling, group 3 exhibited a higher degree of trueness than group 2 before thermocycling, and group 2 had a higher degree of trueness than group 3 after thermocycling. There was a significant difference in the precision for each CDB type before and after thermocycling (P < 0.05). CONCLUSION: The trueness of the CAD-CAM milling system in complete denture (CD) fabrication is superior to that of the 3D printing and conventional compression molding systems before and after thermocycling. Thermocycling had a significant effect on the precision of all CDB types. The compression molding system in CD construction is the most negatively affected via thermocycling with regard to the measures of trueness and precision. CLINICAL TRIAL NUMBER: Not applicable, no human participants were involved.

Asunto(s)

RESUMEN

AIM: The study aims to assess the effect of surface treatments by chemical agents on the retentive strengths of crowns fabricated from polymethylmethacrylate (PMMA) reinforced with graphene nanoparticles adhesively bonded to abutments after thermocycling. SETTINGS AND DESIGN: In vitro comparative study. MATERIALS AND METHODS: This study is composed of four groups - one control, one treated with 99% pure etchant acetone solution, one treated with 15 wt% potassium hydrogen fluoride solution, and the last group treated with a combination of both solutions. RESULTS: The results showed that the mean load in Group A is 228.46±3.16, Group B is 252.57±7.14, Group C is 184.51±6.61, and Group D is 211.03±2.54. The mean score is highest for Group B followed by Group A and Group D, and it is least for Group C. One-way analysis of variance (ANOVA) detected highly significant differences (p<0.01) among the four groups. CONCLUSION: It can be concluded that acetone is the best chemical etchant solution for crowns fabricated from G-CAM discs (Graphenano Dental, Graphenano Nanotechnologies, Spain).

RESUMEN

Background Choosing the optimal aligner material on the market is crucial to ensure constant forces for tooth displacement. Processes like manufacturing and intraoral usage can result in the degradation of certain properties, which can affect the overall efficacy of treatment. Objective The objective of the study is to compare the surface roughness and flexural modulus of two aligner materials following the processes of thermoforming and aging. Materials and methods Two groups of 12 samples each were tested: Group 1 consisted of polyethylene terephthalate glycol (PET-G) and Group 2 of zendura-polyurethane (PU). The groups were tested at three time points: T0 - pre-thermoformed; T1 - after thermoforming; T2 - after thermoforming and aging. The surface roughness and the flexural modulus were evaluated. One-way ANOVA followed by a Bonferroni post hoc test was conducted to compare the changes within each group across the three times. An independent t-test was done to compare the values between the two groups at each time point. The statistical tests were performed using SPSS software version 26 (IBM Corp., Armonk, NY, USA). P-values >0.05 were considered statistically significant. Results There was a significant change in the surface roughness post-aging in Group 2 (p=0.03) and flexural strength within Group 1 (p=0.031) and Group 2 (p=0.06) across the three time points. Comparing the changes within the three time points in Group 1, significant changes were observed between T0-T1 (p=0.045) and T0-T2 (p=0.07). In Group 2, significant changes were observed between T0-T2 (p=0.012). Comparing the flexural strength between the two groups, significant differences were observed at T0 (p=0.012) and T1 (p=0.001). Conclusion The aging process affected the surface roughness in Zendura (PU). The thermoforming and aging process resulted in reduced flexural strength in both Zendura (PU) and Duran groups (PET-G).

RESUMEN

This study explores the effect of using dental brushes with or without metacrylate-based modeling resins on long-term color stability and surface topographies of resin-based composites. This study examined the effects of two variables: (1) the type of brush used (Art brush, Micro-brush, or Mylar strip) and (2) the application of a modeling resin (applied or not applied). The specimens were artificially aged through 10,000 cycles of thermocycling and subsequently immersed in coffee for 30 days. Measurements of color and surface roughness were taken at baseline and after the aging, using a non-contact profilometer for surface roughness and a spectrophotometer for color. Data were analyzed using paired t-tests and one-way ANOVA. Resin-based composites smoothed with dental brushes or micro brushes without modeling resins exhibited lower color change (ΔE) than other groups. Paired t-tests revealed significant differences in average surface roughness (Ra) and valley depth (Rv) for each surfacing technique before and after aging (p ⩽ 0.01). The root means square average of the profile heights (Rq) significantly increased in the control and micro-brush groups (p ⩽ 0.01). In conclusion, the use of brushes in resin-based composites placement does not increase the susceptibility to staining. Instead, the inclusion of resin modeling contributes to discoloration over time.

Asunto(s)

RESUMEN

Adhesion of zirconia is difficult; thus, etching agents using several different methods are being developed. We investigated the effects of surface treatment with commercially available etching agents on the bond strength between zirconia and resin cement and compared them with those achieved using air abrasion alone. We used 100 zirconia blocks, of which 20 blocks remained untreated, 20 blocks were sandblasted, and 60 blocks were acid-etched using three different zirconia-etching systems: Zircos-E etching (strong-acid etching), smart etching (acid etching after air abrasion), and cloud etching (acid etching under a hot stream). Each group was subjected to a bonding procedure with dual-polymerized resin cement, and then 50 specimens were thermocycled. The shear bond strengths between the resin cement and zirconia before and after the thermocycling were evaluated. We observed that in the groups that did not undergo thermocycling, specimens surface-treated with solution did not show a significant increase in shear bond strength compared to the sandblasted specimens (p > 0.05). Among the thermocycled groups, the smart-etched specimens showed the highest shear bond strength. In the short term, various etching agents did not show a significant increase in bond strength compared to sandblasting alone, but in the long term, smart etching showed stability in bond strength (p < 0.05).

RESUMEN

Dental technology has developed materials for prosthetics that are very similar to natural teeth and offer a good balance between durability and esthetics; however, some of these materials are not very color-stable under the influence of external factors. Therefore, the aim of this study is to determine and compare the color change (∆E00) of different esthetic monolithic monochromatic CAD/CAM materials after they have been thermocycled and treated with staining solutions. The color parameters were determined using a spectrophotometer on a white and black background. Five CAD/CAM materials were used for this study-CAD/CAM nanoceramic (GC Cerasmart270), CAD/CAM lithium disilicate ceramic (IPS e.max CAD), CAD/CAM polymer (Telio CAD), CAD/CAM composite (Tetric CAD) and CAD/CAM polymer-infiltrated ceramic (Vita Enamic). The test specimens produced were divided into groups and were thermocycled in distilled water. They were then stored for four weeks at 37 °C in either distilled water as a control liquid, black tea, instant coffee or red wine. The aim is also to evaluate the color changes as a function of the exposure time of the staining solutions. The results obtained were analyzed statistically. All CAD/CAM materials tend to discolor to varying degrees. Among the factors contributing to discoloration, red wine proved to be the most significant influencing factor. The conclusion from the results is that the color change is influenced by the type of material, the staining solution, the sample thickness, the color background and the aging time.

RESUMEN

OBJECTIVES: This in vitro study examined the marginal integrity of experimental composite materials doped with bioactive glass (BG). MATERIALS AND METHODS: Class-II MOD cavities were prepared and restored with one of the following composite materials: a commercial composite material as a reference (Filtek Supreme XTE), an experimental composite doped with BG 45S5 (C-20), and an experimental composite doped with a fluoride-containing BG (F-20). Six experimental groups (n = 8) were used, as each of the three composites was applied with (+) or without (-) a universal adhesive (Adper Scotchbond Multipurpose). All specimens were subjected to thermocycling (10,000 x, 5-55 °C) and then additionally stored in artificial saliva for eight weeks. Scanning electron micrographs of the mesial and the distal box were taken at three time points (initial, after thermocycling, and after eight weeks of storage in artificial saliva). The margins were classified as "continuous" and "non-continuous" and the percentage of continuous margins (PCM) was statistically analyzed (α = 0.05). RESULTS: In most experimental groups, thermocycling led to a significant decrease in PCM, while the additional 8-week aging had no significant effect. F-20 + performed significantly better (p = 0.005) after 8 weeks storage in artificial saliva than the reference material with adhesive, while no statistically significant differences were observed at the other two time points. C-20 + exhibited significantly better PCM than the reference material with adhesive after thermocycling (p = 0.026) and after 8 weeks (p = 0.003). CONCLUSIONS: Overall, the experimental composites with BG showed at least as good marginal adaptation as the commercial reference, with an indication of possible re-sealing of marginal gaps. CLINICAL RELEVANCE: Maintaining or improving the marginal integrity of composite restorations is important to prevent microleakage and its likely consequences such as pulp irritation and secondary caries.

Asunto(s)

RESUMEN

AIMS AND OBJECTIVES: To evaluate the effect of coffee thermocycling on color stability and translucency of CAD-CAM polychromatic high translucent zirconia compared with lithium disilicate glass ceramic. METHODS: Sixteen rectangular plates (14 × 16 × 1.0 mm) of two ceramic materials (IPS E.max CAD (IEC), IPS E.max ZirCAD Prime [IZP]) were prepared. Each specimen was measured for color coordinates using a spectrophotometer following 30,000 cycles of coffee thermocycling. CIELAB formula was used to determine color and translucency differences (ΔE and ΔTP). The means of ΔE and ΔTP were compared using independent samples t-test and were evaluated using their respective 50%:50% perceptibility and acceptability thresholds (PT and AT). One-way analysis of variance was performed to evaluate the translucency parameter (TP) and surface roughness (Ra) of each material. RESULTS: Mean ΔE values of IEC (4.69) and IZP (4.64) were higher than the AT (ΔE ≤ 2.7) with no significant difference found between the two groups (p = 0.202). Considering the TP, only IEC showed a statistically significant increase in TP value (p < 0.001). However, the mean ΔTP of IEC (3.25) remained within the range of acceptability (1.3 < ΔTP ≤ 4.4). CONCLUSIONS: Within the limitations of this current study, the color stability of all materials was clinically affected by coffee thermocycling. In terms of translucency, only lithium disilicate glass ceramic was influenced by coffee thermocycling. High translucent zirconia had superior translucency stability compared to lithium disilicate glass ceramic.

Asunto(s)

RESUMEN

OBJECTIVES: This study aimed to evaluate the shear bond strength and failure behavior between cobalt-chromium (Co-Cr) alloy and different types of denture base resins (DBRs) over time. METHODS: Seventy-two disk-shaped specimens (8 mm in diameter and 2 mm in thickness) were manufactured using a selective laser melting technology-based metal 3D printer. Three types of DBRs were used: heat-cure (HEA group), cold-cure (COL group), and 3D-printable (TDP group) DBRs (n = 12 per group). Each DBR specimen was fabricated as a 5 mm × 5 mm × 5 mm cube model. The specimens of the TDP group were manufactured using a digital light processing technology-based 3D printer. Half of the DBRs were stored in distilled water at 37 °C for 24 h, whereas the remaining half underwent thermocycling for 10,000 cycles. Shear bond strength was measured using a universal testing machine; failure modes were observed, and metal surfaces were evaluated using energy dispersive spectrometry. RESULTS: The shear bond strength did not differ between the DBR types within the non-thermocycled groups. Contrarily, the TDP group exhibited inferior strength compared to the HEA group (P = 0.008) after thermocycling. All three types of DBRs exhibited a significant decrease in the shear bond strength and an increased tendency toward adhesive failure after thermocycling. CONCLUSIONS: The bond strength between 3D-printable DBRs and Co-Cr alloy was comparable to that of heat-and cold-cure DBRs before thermocycling. However, it exhibited a considerable weakening in comparison to heat-cure DBRs after simulated short-term use. CLINICAL SIGNIFICANCE: The application of 3D-printable DBR in metal framework-incorporated removable partial dentures may be feasible during the early phase of the treatment. However, its application is currently limited because the bond strength between the 3D-printable DBR and metal may weaken after short-term use. Further studies on methods to increase the bond strength between these heterogeneous materials are required.

Asunto(s)

RESUMEN

BACKGROUND: The translucency of different zirconia generations at each time point after thermocycling aging is still lacking. METHODS: Four zirconia materials were used with a total of 60 samples produced from monolithic third generation (5Y) 5 mol% yttria-stabilized zirconia polycrystalline ceramic and fourth generation zirconia (4Y) 4 mol% yttria-stabilized zirconia polycrystalline ceramic, represented by [group1:[CM-5Y] Ceramill Zolid fx (3rd generation zirconia) (Amann Girrbach, Koblach, Austria), group 2:[CM-4Y] Ceramill Zolid HT + (4th generation zirconia) (Amann Girrbach, Koblach, Austria), group 3:[CC-5Y] Cercon XT/ML (Dentsply Sirona, Germany) (3rd generation), and group 4:[CC-4Y] Cercon HT/ML (Dentsply Sirona, Germany) (4th generation)]. The L*a*b* figures were measured by using a spectrophotometer at baseline and after 10,000, 30,000, and 50,000 cycles of thermocycling. At each interval, the translucency of the samples was estimated by using the translucency formula CIEDE2000. The Scheffe post-hoc compared differences among each of the four materials. The Repeated measures ANOVA tested the differences between the materials at each of the different thermocycling intervals (p < .001). Data analyses were evaluated at a significance level of p < .05 (CI 95%). RESULTS: Two-way ANOVA revealed that at baseline the third and fourth generation's zirconia showed statistically significant differences in translucency (P < .001). Translucency values at baseline and after thermocycling exhibited statistically significant changes (p = .003). At each of the time interval; CM-4Y had the highest translucency values followed by CM-5Y, CC-4Y and CC-5Y had the least translucency values. CONCLUSIONS: The third and fourth generations of zirconia displayed different translucencies. Thermocycling affected the translucency of both third and fourth generations of zirconia. At each of the time intervals group 2:[CM-4Y] had the highest TP followed by group1:[CM-5Y], while, group 3:[CC-5Y] and group 4:[CC-4Y] had the least TP.

Asunto(s)

RESUMEN

Introduction Fixed prosthodontic treatment involves the replacement of missing tooth structures with a variety of materials. Several newer metal-free ceramics have been developed in recent years to meet patients' aesthetic needs. The long-term performance of all ceramics, however, is unknown, necessitating a continuous evaluation of the materials' strength. Aim The aim of this study was to compare and evaluate the fracture resistance of IPS E max pressable crowns and graphene crowns, which are luted with Rely X U200 self-adhesive resin cement on the respective dies, as well as thermocycling of IPS E max pressable crowns and thermocycling of graphene crowns. The current review was conducted as an in vitro examination at the Division of Prosthodontics, GSL Dental School, Rajahmundry, Andhra Pradesh, India. Materials and methods On a typodont tooth, a shoulder finish line design was prepared and incisal reduction was performed. The tooth was scanned, designed, and milled to produce 18 metal dies made of cobalt-chrome alloy. These metal dies produced a total of (n=36) all-ceramic crowns, which were divided into two groups based on crown type: 18 IPS E max crowns and 18 graphene crowns. The participants were once again divided into two subgroups within each group, with the purpose of assessing fracture resistance. This evaluation was conducted using a universal testing machine both before and after subjecting the specimens to thermocycling. The obtained data were sent for statistical analysis. Results Fracture resistance values were reduced after thermocycling of both IPS E max and Graphene crowns. Without thermocycling, the fracture resistance values of IPS E max crowns were higher than those of graphene crowns. Conclusions The fracture resistance of IPS E max crowns exhibited a statistically significant increase when compared to graphene crowns. Additionally, it was shown that the fracture resistance of both materials was reduced upon exposure to thermocycling.

RESUMEN

Background and objective Glass ionomer cement (GIC), also known as polyalkenoate cement, has been extensively used in dentistry for both luting and restorative purposes. Despite being the first choice for aesthetic restorations due to their chemical bonding ability to teeth, GICs have faced challenges such as low mechanical properties, abrasion resistance, and sensitivity to moisture, leading to the search for improved materials.  This study aims to assess the effects of thermocycling on the compressive, flexural strength, and microhardness of green-mediated nanocomposite-modified GIC in comparison to traditional GIC. Methodology Green-mediated nanoparticles, consisting of chitosan, titanium, zirconia, and hydroxyapatite (Ch-Ti-Zr-HA), were synthesized using a one-pot synthesis technique to form nanocomposites. These nanocomposites were then incorporated into GIC specimens in varying concentrations (3%, 5%, and 10%), denoted as Group I, Group II, and Group III, respectively. Group IV served as the control, consisting of conventional GIC. To assess the performance of the novel restorative materials over an extended period, compressive strength, flexural strength, and microhardness were measured before and after thermocycling using a universal material testing machine. Furthermore, scanning electron microscopy (SEM) analysis was carried out following the thermocycling process. The collected data were subjected to statistical analysis through one-way analysis of variance (ANOVA) and paired t-tests. Results  The findings demonstrated that, in comparison to the control group, both the mean compressive strength and flexural strength, as well as hardness, were notably higher for the 10% and 5% nanocomposite-modified GIC specimens before and after thermocycling (P < 0.05). Notably, there was no notable difference observed between the 5% and 10% concentrations (P > 0.05). These results suggest that incorporating green-mediated nanocomposites (Ch-Ti-Zr-HA) modified GIC at either 5% or 10% concentration levels leads to improved mechanical properties, indicating their potential as promising alternatives in dental restorative materials. Conclusions Based on our findings, it can be inferred that the 10% and 5% concentrations of green-mediated (Ch-Ti-Zr-HA) modified GIC exhibit superior compressive and flexural strength compared to conventional GIC. Additionally, analysis of the scanning electron microscope (SEM) morphology revealed that green-mediated GIC displays smoother surface characteristics in contrast to conventional GIC. These results underscore the potential advantages of utilizing green-mediated nanocomposite-modified GIC in dental applications, suggesting enhanced mechanical properties and surface quality over conventional.

RESUMEN

Objetivo: Cuando las resinas compuestas son expuestas a procesos de envejecimiento naturales en boca, como es el ciclaje térmico, pueden sufrir un deterioro en sus propiedades ópticas. El objetivo de este estudio fue evaluar la influencia del envejecimiento térmico sobre la estabilidad del color de dos resinas compuestas. Materiales y métodos: Se confeccionaron 120 pas- tillas de resinas compuestas, divididas en dos grupos: uno de resina Spectra Smart (n=60) y otro de resina Filtex Z350 XT (n=60). Estas muestras fueron sometidas a distintos regíme- nes de ciclaje térmico de 0, 10.000, 20.000 y 30.000 ciclos con temperaturas de entre 5 ºC +/- 2 ºC y 55 ºC +/- 2 °C. Los parámetros de color CIE L*a*b* de cada muestra se mi- dieron con un espectrofotómetro antes y después del proceso de envejecimiento. Las diferencias de color se calcularon me- diante la fórmula CIELAB (ΔE). Los datos fueron analizados estadísticamente usando la prueba no paramétrica de Kruskal Wallis y de U-Mann Whitney. Resultados: Los distintos regímenes de termociclado produjeron cambios de color estadísticamente significativos en ambos materiales. El material que tuvo menor estabilidad cromática fue Spectra Smart aunque sin diferencias estadísti- camente significativas. Conclusión: El envejecimiento térmico simulado a tres años afecta la estabilidad de color de las muestras, tanto de las resinas Spectra Smart, como de Filtex Z350 XT, sin alcanzar los valores que clínicamente determinarían la necesidad del reemplazo de las restauraciones (AU)

Aim: When composite resins are exposed to natural ag- ing processes in the mouth, such as the thermal cycling, they may suffer a deterioration in their optical properties. The aim of this study was to evaluate the influence of thermal aging on the color stability of two composite resins. Materials and methods: 120 composite resins tablets were made, divided into two groups: one of Spectra Smart res- in (n=60) and another of Filtex Z350 XT resin (n=60). These were subjected to different thermal cycle regimes of 0, 10,000, 20,000 and 30,000 cycles with temperature between 5 °C +/- 2 °C and 60 °C +/- 2 °C. The CIE L*a*b* color parameters of each sample were measured with a spectrophotometer before and after the aging process. Color differences were calculat- ed using the CIELAB formula (ΔE). The data were statisti- cally analyzed using the non-parametric Kruskal Wallis and U-Mann Whitney tests. Results: The different thermocycling regimes produce statistically significant color changes in both materials. The material that had the least chromatic stability was Spectra Smart, although without statistically significant differences. Conclusion: Simulated 3 year thermal aging affects the color stability of the samples, both Spectra Smart resins and Filtex Z350 XT, without reaching the values that would clini- cally determine the need to replace the restorations (AU)

Asunto(s)

RESUMEN

OBJECTIVE: To investigate the effects of sterilization, conditioning method, and thermal aging on the retentive strength of two-piece zirconia abutments. MATERIALS AND METHODS: In total, 128 stock zirconia abutments were divided into four groups (n = 32) according to the conditioning parameters: (A) air-abrasion using 50 µm alumina particles/1.0 bar, (B) 50 µm/2.0 bar, (C) 100 µm/1.0 bar, and (D) 100 µm/2.0 bar. All abutments were bonded onto titanium bases using DTK adhesive resin and stored in water bath (37°C) for 72 h. Each group was subdivided into two subgroups (n = 16), group 1 was disinfected, whereas group 2 followed disinfection and autoclave sterilization. Half of the specimens of each subgroup (n&#x02009;=&#x02009;8) was directly subjected to the axial retention test (groups N), while the other half was first subjected to 150&#x02009;days of thermocycling followed by retention test (groups T). Statistical analysis was performed with three-way ANOVA, additional statistical analysis was performed by using separate one-way ANOVAs followed by the Tukey's post-hoc test for post hoc pairwise comparisons among groups. RESULTS: The highest median retention strength was recorded for group B2N (1390 N), whereas the lowest strength was recorded for group C1T (688 N). No significant interaction (p ≥ 0.05) was detected between the different variables; conditioning method, sterilization, and the thermal cycling regarding the effect on the resulting retention. However, the sterilization always showed a positive effect. Thermocycling presented an adversely significant effect only in the absence of sterilization (p < 0.05), with the exception of subgroups A. For the sterilized groups, thermocycling had no statistically significant effect on the retention. CONCLUSION: Steam autoclaving increased the retention of hybrid zirconia abutments. DTK adhesive resin for two-piece zirconia abutments performed well after sterilization and thermocycling.

Asunto(s)

RESUMEN

Background Discoloration affects glass ionomer cement (GIC) color stability due to its brittle nature and microporosity. To counter this, incorporating alternative materials is essential for maintaining color stability. Aim This study aims to determine the color stability and gloss of GIC modified with bioactive chitosan, titanium, zirconia, and hydroxyapatite nanoparticles before and after artificial aging. Materials and methods  The study was conducted at Saveetha Research Centre, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, located in Chennai, India. Green-mediated chitosan, titanium, zirconia, and hydroxyapatite (Ch-Ti-Zr-HA) nanoparticles were synthesized using the one-pot synthesis technique. Forty-eight disc-shaped specimens were prepared by incorporating the obtained nanoparticles (nanocomposite) into the GIC, with a diameter of 5 mm and thickness of 2 mm. The specimens were prepared in different concentrations (3%, 5%, and 10%) designated as group I, group II, and group III, respectively. Group IV, serving as the control, consisted of conventional GIC without any modifications. Following preparation, scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) microanalysis confirmed sample elements, and the specimens were submerged in distilled water for a duration of 24 hours prior to the commencement of testing. Subsequently, the specimens underwent artificial aging (thermocycling), between temperatures of 5°C and 55°C, for a total of 30,000 cycles, with a 30-second dwell time. Color change and gloss characteristics were assessed both after 24 hours and following thermocycling using a spectrophotometer and glossometer, respectively. The average color change parameter (ΔE) was measured using Adobe Photoshop. The data obtained were subjected to statistical analysis using an unpaired t-test. Results Significant color stability variations were observed post thermocycling (P = 0.001). Group 2 (5%) exhibited minimal delta E difference (0.508 ± 0.105), indicating superior color stability, while group 4 (control) had maximum difference (1.15 ± 0.187), indicating lower stability. Gloss tests confirmed GIC's polishability, where there were significant differences among all the groups. Conclusion It can be concluded that 5% nanoparticle-modified GIC has better color stability and gloss than conventional GIC. Further studies are needed to analyze the color stability and gloss through dentifrices and other beverages.

RESUMEN

Background/purpose: Polyetheretherketone (PEEK) is a highly sought-after thermoplastic due to its exceptional mechanical properties and biocompatibility. However, bonding PEEK to indirect composite resin (ICR) or denture-based resin (DBR) can be challenging. Laser engraving technology has shown potential to improve bonding for other materials; thus, this study aims to evaluate its effectiveness for PEEK. Materials and methods: The experiment involved preparing ingot-shaped PEEK samples, which were then categorized into four groups based on the treatment method employed: without treatment, air abrasion, sulfuric acid etching, and laser engraving (LS). Subsequently, the samples were bonded to ICR or DBR, and their shear bond strength (SBS) was tested with or without thermocycling using a universal testing machine. Furthermore, the failure mode was observed, with statistical analyses conducted to compare the results. Results: The grid-like microslit structure of LS group displayed the highest SBS for bonding PEEK to ICR or DBR (P < 0.05). During the bonding of PEEK to ICR, resin residue and penetration into the microslits were frequently observed in the LS group, indicating cohesive failure. However, when PEEK was bonded to DBR, mixture failure was frequently observed without thermocycling. After thermocycling, only the LS group showed cohesive failure, while the majority of specimens exhibited mixture failure. Conclusion: Laser engraving significantly improves the SBS between PEEK and both ICR and DBR. Furthermore, it was observed that resin had penetrated the microslits, indicating that laser engraving has great potential as a surface treatment method.

RESUMEN

OBJECTIVE: The current dental resin composites often suffer from polymerization shrinkage, which can lead to microleakage and potentially result in recurring tooth decay. This study presents the synthesis of a novel monomer, (3,9-diethyl-1,5,7,11-tetraoxaspiro[5,5]undecane-3,9-diyl)bis(methylene) bis((2-(3-(prop-1-en-2-yl)phenyl)propan-2-yl)carbamate) (DDTU-IDI), and evaluates its effect in the formulation of low-shrinkage dental resin composites. METHODS: DDTU-IDI was synthesized through a two-step reaction route, with the initial synthesis of the required raw material monomer 3,9-diethyl-3,9-dihydroxymethyl-1,5,7,11-tetraoxaspiro-[5,5] undecane (DDTU). The structures were confirmed using Fourier-transform infrared (FT-IR) spectroscopy and hydrogen nuclear magnetic resonance (1HNMR) spectroscopy. Subsequently, DDTU-IDI was incorporated into Bis-GMA-based composites at varying weight percentages (5, 10, 15, and 20 wt%). The polymerization reaction, degree of conversion, polymerization shrinkage, mechanical properties, physicochemical properties and biocompatibility of the low-shrinkage composites were thoroughly evaluated. Furthermore, the mechanical properties were assessed after a thermal cycling test with 10,000 cycles to determine the stability. RESULTS: The addition of DDTU-IDI at 10, 15, and 20 wt% significantly reduced the polymerization volumetric shrinkage of the experimental resin composites, without compromising the degree of conversion, mechanical and physicochemical properties. Remarkably, at a monomer content of 20 wt%, the polymerization shrinkage was reduced to 1.83 ± 0.53%. Composites containing 10, 15, and 20 wt% DDTU-IDI exhibited lower water sorption and higher contact angle. Following thermal cycling, the composites exhibited no significant decrease in mechanical properties, except for the flexural properties. SIGNIFICANCE: DDTU-IDI has favorable potential as a component which could produce volume expansion and increase rigidity in the development of low-shrinkage dental resin composites. The development of low-shrinkage composites containing DDTU-IDI appears to be a promising strategy for reducing polymerization shrinkage, thereby potentially enhancing the longevity of dental restorations.

Asunto(s)