RESUMEN

Most metallic commercial bone anchors, such as screws and suture anchors achieve their fixation to bone through shear of the bone located between the threads. They have several deficiencies, potentially leading to failure, which are particularly evident in low-density bone. These include stress-shielding resulting from mechanical properties mismatch; lack of mechanically induced remodeling and osteointegration; and when the pullout force on the anchor, during functional activities, exceeds their pullout strength, catastrophic failure occurs leaving behind large bone defects that may be hard to repair. To overcome these deficiencies, we introduced in this study a porous swelling co-polymeric material and studied its swelling and compressive mechanical characteristics as bone anchor under different configurations. Porosity was achieved by adding a non-dissolvable agent (NaCl) during the process of polymerization, which was later dissolved in water, leaving behind a porous structure with adequate porosity for osteointegration. Three different groups of cylindrical samples of the swelling co-polymer were investigated. Solid, fully porous, and partially porous with a solid core and a porous outer layer. The results of the swelling and simple compression study show that the partially porous swelling co-polymer maintains excellent mechanical properties matching those of cancellous bone, quick swelling response, and an adequate porous outer layer for mechanically induced osteointegration. These suggest that this material may present an effective alternative to conventional bone anchors particularly in low-density bone.

Asunto(s)

RESUMEN

The swelling characteristics of porous media in the offshore natural gas hydrate reservoir have an important effect on the stability of the reservoir. In this work, the physical property and the swelling of porous media in the offshore natural gas hydrate reservoir were measured. The results show that the swelling characteristics of the offshore natural gas hydrate reservoir are influenced by the coupling of the montmorillonite content and the salt ion concentration. The swelling rate of porous media is directly proportionate to water content and the initial porosity, and inversely proportionate to salinity. Compared with water content and salinity, the initial porosity has much obvious influence on the swelling, which the swelling strain of porous media with the initial porosity of 30% is three times more than that of montmorillonite with the initial porosity of 60%. Salt ions mainly affect the swelling of water bound by porous media. Then, the influence mechanism of the swelling characteristics of porous media on the structural characteristics of reservoir was tentatively explored. It can provide a basic date and scientific basis for furthering the mechanical characteristics of the reservoir in the hydrate exploitation in the offshore gas hydrate reservoir.

RESUMEN

Objects touched by patients and healthcare workers in hospitals may harbor pathogens, including multi-drug resistant (MDR) staphylococci, enterococci (VRE), Escherichia coli, Acinetobacter, and Pseudomonas species. Medical devices contaminated by these pathogens may also act as a source of severe and difficult-to-treat human infections, thus becoming a critical public health concern requiring urgent resolutions. To this end, we recently reported the bactericidal effects of a cationic copolymer (CP1). Here, aiming at developing a bactericidal formulation possibly to be used either for surfaces disinfection or to treat skin infections, CP1 was formulated as a hydrogel (CP1_1.1-Hgel). Importantly, even if not cross-linked, CP1 formed the gel upon simple dispersion in water, without requiring gelling agents or other additives which could be skin-incompatible or interfere with CP1 bactericidal effects in possible future topical applications. CP1_1.1-Hgel was characterized by attenuated-total-reflectance Fourier transform infrared (ATR-FTIR) and UV-Vis spectroscopy, as well as optic and scanning electron microscopy (OM and SEM) to investigate its chemical structure and morphology. Its stability was assessed by monitoring its inversion properties over time at room temperature, while its mechanical characteristics were assessed by rheological experiments. Dose-dependent cytotoxicity studies performed on human fibroblasts for 24 h with gel samples obtained by diluting CP_1.1-Hgel at properly selected concentrations established that the 3D network formation did not significantly affect the cytotoxic profile of CP1. Also, microbiologic investigations carried out on two-fold serial dilutions of CP1-gel confirmed the minimum inhibitory concentrations (MICs) previously reported for the not formulated CP1.Selectivity indices values up to 12 were estimated by the values of LD50 and MICs determined here on gel samples.

Asunto(s)

RESUMEN

Wide-pore cryostructurates were prepared via freezing sodium alginate aqueous solutions with subsequent ice sublimation from the frozen samples, followed by their incubation in the ethanol solutions of calcium chloride or sulfuric acid, rinsing, and final drying. Such sequence of operations resulted in the calcium alginate or alginic acid sponges, respectively. The swelling degree of the walls of macropores in such matrices decreased with increasing polymer concentration in the initial solution. The dependence of the degree of swelling on the cryogenic processing temperature had a bell-like character with a maximum for the samples formed at -20 °C. According to 1H NMR spectroscopy, the content of mobile (non-frozen) water in the frozen water-sodium alginate systems also depended on the initial polymer concentration and freezing temperature. The cryostructurates obtained did not lose their integrity in water, saline, in an acidic medium at pH 2 for at least three weeks. Under alkaline conditions at pH 12 the first signs of dissolution of the Ca-alginate sponge arose only after a week of incubation. Microbiological testing of the model depot form of the antibiotics entrapped in the Ca-alginate cryostructurate demonstrated the efficiency of this system as the antibacterial material.

RESUMEN

In this study, superabsorbent nanocomposites of guar gum grafted sodium acrylate have been synthesized via both microwave and conventional techniques. The reaction parameters of both techniques were optimized and the microwave assisted method was proved to have higher grafting yield with lesser time of reaction as compared to the conventional method. X-ray diffraction and scanning electron microscopy analyses revealed that cloisite was exfoliated and uniformly dispersed in guar gum grafted sodium acrylate matrix. The results show that introducing cloisite into the guar gum grafted sodium acrylate network improved the swelling capability and the swelling rate of the superabsorbent nanocomposite was found to be enhanced at an optimal loading of 10% cloisite. The nanocomposites showed high water absorbency within a wide pH range. Preliminary studies on crystal violet dye removal showed promising results.

Asunto(s)