RESUMEN

The abundant defects on the perovskite surface greatly impact the efficiency improvement and long-term stability of carbon-based perovskite solar cells. Molecules with electron-donating or electron-withdrawing functional groups have been cited for passivating various defects. However, few studies have investigated the potential adverse effects arising from the synergistic interactions among functional groups. Herein, we investigate the correlation between functional group configurations and passivation strength as well as the potential adverse impacts of strong electrostatic structures by methodically designing three distinct interface molecules functionalized with different ending groups, which both belong to biguanide derivatives, including 1-(3,4-dichlorophenyl) biguanide hydrochloride (DBGCl), metformin hydrochloride (MFCl), and biguanide hydrochloride (BGCl). The results indicate that DBGCl establishes comparatively mild active sites, not only passivates defects but also aids in forming a surface with a uniform potential. Conversely, MFCl exerts a more pronounced adverse effect on the perovskite surface, which is attributable to the electronic state perturbations induced by its functional groups. Due to the lack of hydrophobic groups, devices treated with BGCl demonstrate insufficient moisture resistance. Devices passivated with DBGCl demonstrate superior average efficiency, showcasing a 12% enhancement relative to the pristine. Furthermore, DBGCl-treated devices exhibit enhanced stability in three different environments, respectively, achieving the highest PCE retention rates under nitrogen conditions (25 °C), room-temperature air conditions (25 °C, RH = 40 ± 2%), and high-temperature air conditions (65 °C, RH = 40 ± 2%).

RESUMEN

In this study, a series of dopant-free, low-cost hole-transporting materials (HTMs) based on triphenylamine-functionalized azadipyrromethene dyes 1-3 (TPA-ADPs 1-3) were designed and synthesized. The properties of these new HTMs were investigated by optical spectroscopy, cyclic voltammetry, thermogravimetric analysis, differential scanning calorimetric, atomic force microscopy, and X-ray diffraction, as well as theoretical calculations. The results indicated that the TPA-ADPs 1-3 presented well-matched energy levels with perovskite, higher hole mobility, as well as more effective defect passivation at the perovskite/HTM interface by the coordination interaction between the ADP moiety and the undercoordinated Pb2+. The n-i-p perovskite solar cells (PSCs) employing HTMs 1-3 as well as doped Spiro-OMeTAD were fabricated and characterized. The TPA-ADP 1-based PSCs exhibited the best performance with a champion power conversion efficiency (PCE) of 22.13% and an fill factor of 0.81, which was superior to that of the devices based on the doped Spiro-OMeTAD. Long-term device performance studies indicated that the TPA-ADP 1-based PSCs maintained 80% of the initial PCE after 1800 h of storage in the ambient condition of 40-60% RH, which was also higher than the stability of doped Spiro-OMeTAD-based devices under the same conditions.

RESUMEN

Traditionally used phenylethylamine iodide (PEAI) and its derivatives, such as ortho-fluorine o-F-PEAI, in interfacial modification, are beneficial for perovskite solar cell (PSC) efficiency but vulnerable to heat stability above 85 °C due to ion migration. To address this issue, we propose a composite interface modification layer incorporating the discotic liquid crystal 2,3,6,7,10,11-hexa(pentoxy)triphenylene (HAT5) into o-F-PEAI. The triphenyl core in HAT5 promotes π-π stacking self-assembly and enhances its interaction with o-F-PEAI, forming an oriented columnar phase that improves hole extraction along the one-dimensional direction. HAT5 repairs structural defects in the interfacial layer and retains the layered structure to inhibit ion migration after annealing. Ultimately, our approach increases the efficiency of solar cells from 23.36% to 25.02%. The thermal stability of the devices retains 80.1% of their initial efficiency after aging at 85 °C for 1008 hours without encapsulation. Moreover, the optimized PSCs maintained their initial efficiency of 82.4% after aging under one sunlight exposure for 1008 hours. This study provides a novel strategy using composite materials for interface modification to enhance the thermal and light stability of semiconductor devices.

RESUMEN

Full-area passivating contacts based on SiOx/poly-Si stacks are key for the new generation of industrial silicon solar cells substituting the passivated emitter and rear cell (PERC) technology. Demonstrating a potential efficiency increase of 1 to 2% compared to PERC, the utilization of n-type wafers with an n-type contact at the back and a p-type diffused boron emitter has become the industry standard in 2024. In this work, variations of this technology are explored, considering p-type passivating contacts on p-type Si wafers formed via a rapid thermal processing (RTP) step. These contacts could be useful in conjunction with n-type contacts for realizing solar cells with passivating contacts on both sides. Here, a particular focus is set on investigating the influence of the applied thermal treatment on the interfacial silicon oxide (SiOx) layer. Thin SiOx layers formed via ultraviolet (UV)-O3 exposure are compared with layers obtained through a plasma treatment with nitrous oxide (N2O). This process is performed in the same plasma enhanced chemical vapor deposition (PECVD) chamber used to grow the Si-based passivating layer, resulting in a streamlined process flow. For both oxide types, the influence of the RTP thermal budget on passivation quality and contact resistivity is investigated. Whereas the UV-O3 oxide shows a pronounced degradation when using high thermal budget annealing (T > 860 °C), the N2O-plasma oxide exhibits instead an excellent passivation quality under these conditions. Simultaneously, the contact resistivity achieved with the N2O-plasma oxide layer is comparable to that yielded by UV-O3-grown oxides. To unravel the mechanisms behind the improved performance obtained with the N2O-plasma oxide at high thermal budget, characterization by high-resolution (scanning) transmission electron microscopy (HR-(S)TEM), X-ray reflectometry (XRR) and X-ray photoelectron spectroscopy (XPS) is conducted on layer stacks featuring both N2O and UV-O3 oxides after RTP. A breakup of the UV-O3 oxide at high thermal budget is observed, whereas the N2O oxide is found to maintain its structural integrity along the interface. Furthermore, chemical analysis reveals that the N2O oxide is richer in oxygen and contains a higher amount of nitrogen compared to the UV-O3 oxide. These distinguishing characteristics can be directly linked to the enhanced stability exhibited by the N2O oxide under higher annealing temperatures and extended dwell times.

RESUMEN

Small metal-rich semiconducting quantum dots (QDs) are promising for solid-state lighting and single-photon emission due to their highly tunable yet narrow emission line widths. Nonetheless, the anionic ligands commonly employed to passivate these QDs exert a substantial influence on the optoelectronic characteristics, primarily owing to strong electron-phonon interactions. In this work, we combine time-domain density functional theory and nonadiabatic molecular dynamics to investigate the excited charge carrier dynamics of Cd28Se17X22 QDs (X = HCOO-, OH-, Cl-, and SH-) at ambient conditions. These chemically distinct but regularly used molecular groups influence the dynamic surface-ligand interfacial interactions in Cd-rich QDs, drastically modifying their vibrational characteristics. The strong electron-phonon coupling leads to substantial transient variations at the band edge states. The strength of these interactions closely depends on the physicochemical characteristics of passivating ligands. Consequently, the ligands largely control the nonradiative recombination rates and emission characteristics in these QDs. Our simulations indicate that Cd28Se17(OH)22 has the fastest nonradiative recombination rate due to the strongest electron-phonon interactions. Conversely, QDs passivated with thiolate or chloride exhibit considerably longer carrier lifetimes and suppressed nonradiative processes. The ligand-controlled electron-phonon interactions further give rise to the broadest and narrowest intrinsic optical line widths for OH and Cl-passivated single QDs, respectively. Obtained computational insights lay the groundwork for designing appropriate passivating ligands on metal-rich QDs, making them suitable for a wide range of applications, from blue LEDs to quantum emitters.

RESUMEN

Surface ligand chemistry is vital to control the synthesis, diminish surface defects, and improve the electronic coupling of quantum dots (QDs) toward emerging applications in optoelectronic devices. Here, we successfully develop highly homogeneous and dispersed AgBiS2 QDs, focus on the control of interdot spacing, and substitute the long-chain ligands with ammonium iodide in solution. This results in improved electronic coupling of AgBiS2 QDs with excellent surface passivation, which greatly facilitates carrier transport within the QD films. Based on the stable AgBiS2 QD dispersion with the optimal ligand state, a homogeneous and densely packed QD film is prepared by a facile one-step coating process, delivering a champion power conversion efficiency of approximately 8% in the QD solar cells with outstanding shelf life stability. The proposed surface engineering strategy holds the potential to become a universal preprocessing step in the realm of high-performance QD optoelectronic devices.

RESUMEN

As the initial synthesized colloidal quantum dots (CQDs) are generally capped with insulating ligands, ligand exchange strategies are essential in the fabrication of CQD films for solar cells, which can regulate the surface chemical states of CQDs to make them more suitable for thin-film optoelectronic devices. However, uncontrollable surface adsorption of water molecules during the ligand exchange process introduces new defect sites, thereby impairing the resultant device performance, which attracts more efforts devoted to it but remains a puzzle. Here, we develop a solvent-engineering-assisted ligand exchange strategy to revamp the surface adsorption, improve the exchange efficiency, and modulate the surface chemistry for the environmentally friendly lead-free silver bismuth disulfide (AgBiS2) CQDs. The optimized AgBiS2 CQD solar cells deliver an outstanding champion power conversion efficiency (PCE) of up to 8.95% and improved long-term stability. Our strategy is less environment-dependent and can produce solar cells with negligible performance variance for several batches across several months. Our work demonstrates the critical role of solvents for ligand exchange in the surface chemistry of CQDs and the realization of high-performance photovoltaic devices in a highly reproducible manner.

RESUMEN

In this study, we investigate the impact of two-dimensional MoS2 coating on the optical properties of surface GaN/AlGaN quantum wells (QWs). A strong enhancement in GaN QW light emission is observed with monolayer-MoS2 coating, yielding luminescence intensity comparable to that from a QW capped by an AlGaN barrier. Our results demonstrate that MoS2, despite its quite different nature from III-nitride semiconductors, acts as an effective barrier for surface GaN QWs and suppresses spatially localized intrinsic surface states. This finding provides novel pathways for efficient III-nitride surface passivation.

RESUMEN

The cubic α-CsPbI3 phase stands out as one of the most promising perovskite compounds for solar cell applications due to its suitable electronic band gap of 1.7 eV. However, it exhibits structural instability under operational conditions, often transforming into the hexagonal non-perovskite δ-CsPbI3 phase, which is unsuitable for solar cell applications because of the large band gap (e.g., ∼2.9 eV). Thus, there is growing interest in identifying possible mechanisms for increasing the stability of the cubic α-CsPbI3 phase. Here, we report a theoretical investigation, based on density functional theory calculations, of the surface passivation of the α-, γ-, and δ-CsPbI3(100) surfaces using the C6H4(NH3)2 [p-phenylenediamine (PPD)] and Cs species as passivation agents. Our calculations and analyses corroborate recent experimental findings, showing that PPD passivation effectively stabilizes the cubic α-CsPbI3 perovskite against the cubic-to-hexagonal phase transition. The PPD molecule exhibits covalent-dominating bonds with the substrate, which makes it more resistant to distortion than the ionic bonds dominant in perovskite bulks. By contrasting these results with the natural Cs passivation, we highlight the superior stability of the PPD passivation, as evidenced by the negative surface formation energies, unlike the positive values observed for the Cs passivation. This disparity is due to the covalent characteristics of the molecule/surface interaction of PPD, as opposed to the purely ionic interaction seen with the Cs passivation. Notably, the PPD passivation maintains the optoelectronic properties of the perovskites because the electronic states derived from the PPD molecules are localized far from the band gap region, which is crucial for optoelectronic applications.

RESUMEN

Recent investigations were shifted this trend toward exploring the biomedical applicability of CDs, relevant to chronic diseases. Herein, a systematic approach is demonstrated for studying the effect of variation in the surface passivation of CDs for tuning its optical character and biological performance. Alginate and pectin were successfully clustered oxygen-surface passivated CDs, while, chitin was used to nucleate nitrogen-surface passivated CDs. Pectin-treated with base (4.1 ± 1.8 nm) and chitin-treated acid (3.5 ± 1.7 nm) were ingrained the smallest O-surface passivated CDs and N-surface passivated CDs, respectively. However, N-surface passivated CDs were shown with the highest optical activity. CDs colloids prepared from alginate, pectin & chitin, resulted in reduction of tumor cell viability percentage to be 80.8%, 74.0% & 69.0% respectively. O-surface passivated CDs nucleated from alginate showed the highest anti-proliferative effects. Moreover, O-surface passivated CDs (from alginate) showed the supremacy in inhibition of inflammation, while, increasing of its concentration ten times resulted in significant increment in inhibition percent to be 28% & 42%, using 1 µg/mL & 10 µg/mL, respectively. In summarization, it could be decided that, compared to N-surface passivated CDs (from chitin), O-surface passivated CDs (from alginate) showed excellency in application as a concurrent anti-inflammatory/antitumor drug, to be applied as a potential therapeutical reagent for treatment of inflammation, in production of vaccines, immune-therapeutics, and immune-suppressive drugs.

RESUMEN

Preventing nonspecific binding is essential for sensitive surface-based quantitative single-molecule microscopy. Here we report a much-simplified RainX-F127 (RF-127) surface with improved passivation. This surface achieves up to 100-fold less nonspecific binding from protein aggregates compared to commonly used polyethylene glycol (PEG) surfaces. The method is compatible with common single-molecule techniques including single-molecule pull-down (SiMPull), super-resolution imaging, antibody-binding screening and single exosome visualization. This method is also able to specifically detect alpha-synuclein (α-syn) and tau aggregates from a wide range of biofluids including human serum, brain extracts, cerebrospinal fluid (CSF) and saliva. The simplicity of this method further allows the functionalization of microplates for robot-assisted high-throughput single-molecule experiments. Overall, this simple but improved surface offers a versatile platform for quantitative single-molecule microscopy without the need for specialized equipment or personnel.

Asunto(s)

RESUMEN

Mass photometry (MP) is a rapidly growing optical technique for label-free mass measurement of single biomolecules in solution. The underlying measurement principle provides numerous advantages over ensemble-based methods but has been limited to low analyte concentrations due to the need to uniquely and accurately quantify the binding of individual molecules to the measurement surface, which results in diffraction-limited spots. Here, we combine nanoparticle lithography with surface PEGylation to substantially lower surface binding, resulting in a 2 orders of magnitude improvement in the upper concentration limit associated with mass photometry. We demonstrate the facile tunability of degree of passivation, enabling measurements at increased analyte concentrations. These advances provide access to protein-protein interactions in the high nanomolar to low micromolar range, substantially expanding the application space of mass photometry.

Asunto(s)

RESUMEN

Near-infrared light-emitting diodes (NIR LEDs) based on perovskite quantum dots (QDs) have produced external quantum efficiency (EQE) of ~15 %. However, these high-performance NIR-QLEDs suffer from immediate carrier quenching because of the accumulation of migratable ions at the surface of the QDs. These uncoordinated ions and carriers-if not bound to the nanocrystal surface-serve as centers for exciton quenching and device degradation. In this work, we overcome this issue and fabricate high-performance NIR QLEDs by devising a ligand anchoring strategy, which entails dissolving the strong-binding ligand (Guanidine Hydroiodide, GAI) in the mediate-polar solvent. By employing the dye-sensitized device structure (phosphorescent indicator), we demonstrate the elimination of the interface defects. The treated QDs films exhibit an exciton binding energy of 117 meV: this represents a 1.5-fold increase compared to that of the control (74 meV). We report, as a result, the NIR QLEDs with an EQE of 21 % which is a record among NIR perovskite QLEDs. These QLEDs also exhibit a 7-fold higher operational stability than that of the best previously reported NIR QLEDs. Furthermore, we demonstrate that the QDs are compatible with large-area QLEDs: we showcase 900 mm2 QLEDs with EQE approaching 20 %.

RESUMEN

Developing large-scale monolithic perovskite/silicon tandem devices based on industrial Czochralski silicon wafers will likely have to adopt double-side textured architecture, given their optical benefits and low manufacturing costs. However, the surface engineering strategies that are widely used in solution-processed perovskites to regulate the interface properties are not directly applicable to micrometric textures. Here, we devise a surface passivation strategy by dynamic spray coating (DSC) fluorinated thiophenethylammonium ligands, combining the advantages of providing conformal coverage and suppressing phase conversion on textured surfaces. From the viewpoint of molecular engineering, theoretical calculation and experimental results demonstrate that introducing trifluoromethyl group provide more effective surface passivation through strong interaction and energy alignment by forming a dipole layer. Consequently, the DSC treatment of this bifunctional molecule enables the tandem cells based on industrial silicon wafers to achieve a certified stabilized power conversion efficiency of 30.89 %. In addition, encapsulated devices display excellent operational stability by retaining over 97 % of their initial performance after 600 h continuous illumination.

RESUMEN

Inverted NiOx-based perovskite solar cells (PSCs) exhibit considerable potential because of their low-temperature processing and outstanding excellent stability, while is challenged by the carriers transfer at buried interface owing to the inherent low carrier mobility and abundant surface defects that directly deteriorates the overall device fill factor. Present work demonstrates a chemical linker with the capability of simultaneously grasping NiOx and perovskite crystals by forming a Ni-S-Pb bridge at buried interface to significantly boost the carriers transfer, based on a rationally selected molecule of 1,3-dimethyl-benzoimidazol-2-thione (NCS). The constructed buried interface not only reduces the pinholes and needle-like residual PbI2 at the buried interface, but also deepens the work function and valence band maximum positions of NiOx, resulting in a smaller VBM offset between NiOx and perovskite film. Consequently, the modulated PSCs achieved a high fill factor up to 86.24 %, which is as far as we know the highest value in records of NiOx-based inverted PSCs. The NCS custom-tailored PSCs and minimodules (active area of 18 cm2) exhibited a champion efficiency of 25.05 % and 21.16 %, respectively. The unencapsulated devices remains over 90 % of their initial efficiency at maximum power point under continuous illumination for 1700 hours.

RESUMEN

This study aims to enhance the optical and thermal properties of cesium-based perovskite nanocrystals (NCs) through surface passivation with organic sulfonate (or sulfonic acid) ligands. Four different phenylated ligands, including sodium ß-styrenesulfonate (SbSS), sodium benzenesulfonate (SBS), sodium p-toluenesulfonate (SPTS), and 4-dodecylbenzenesulfonic acid (DBSA), were employed to modify blue-emitting CsPbBr1.5Cl1.5 perovskite NCs, resulting in improved size uniformity and surface functionalization. Transmission electron microscopy and X-ray photoelectron spectroscopy confirmed the successful anchoring of sulfonate or sulfonic acid ligands on the surface of perovskite NCs. Moreover, the photoluminescence quantum yield increased from 32% of the original perovskite NCs to 63% of the SPTS-modified ones due to effective surface passivation. Time-resolved photoluminescence decay measurements revealed extended PL lifetimes for ligand-modified NCs, indicative of reduced nonradiative recombination. Thermal stability studies demonstrated that the SPTS-modified NCs retained nearly 80% of the initial PL intensity when heated at 60 °C for 10 min, surpassing the performance of the original NCs. These findings emphasize the optical and thermal stability enhancement of cesium-based perovskite NCs through surface passivation with suitable sulfonate ligands.

RESUMEN

Understanding the interaction between fullerene (C60) and perovskite surfaces is pivotal for advancing the efficiency and stability of perovskite solar cells. In this study, we investigate the adsorption behavior of C60 on methylammonium lead iodide (MAPbI3) surfaces using periodic density functional theory calculations. We explore various surface terminations and defect configurations to elucidate the influence of surface morphology on the C60-perovskite interaction, computing the adsorption energy and transfer of charge. Our results reveal distinct adsorption energies and charge transfer mechanisms for different surface terminations, shedding light on the role of surface defects in modifying the electronic structure and stability of perovskite materials. Furthermore, we provide insights into the potential of C60 to passivate surface defects, playing a relevant role in the surface reconstruction after the formation of defects. This comprehensive understanding of C60-perovskite interactions offers valuable guidelines about the role of fullerenes on surface structure and reconstruction.

RESUMEN

A high-quality nanostructured tin oxide (SnO2) has garnered massive attention as an electron transport layer (ETL) for efficient perovskite solar cells (PSCs). SnO2 is considered the most effective alternative to titanium oxide (TiO2) as ETL because of its low-temperature processing and promising optical and electrical characteristics. However, some essential modifications are still required to further improve the intrinsic characteristics of SnO2, such as mismatch band alignments, charge extraction, transportation, conductivity, and interfacial recombination losses. Herein, an inorganic-based cesium (Cs) dopant is used to modify the SnO2 ETL and to investigate the impact of Cs-dopant in curing interfacial defects, charge-carrier dynamics, and improving the optoelectronic characteristics of PSCs. The incorporation of Cs contents efficiently improves the perovskite film quality by enhancing the transparency, crystallinity, grain size, and light absorption and reduces the defect states and trap densities, resulting in an improved power conversion efficiency (PCE) of ≈22.1% with Cs:SnO2 ETL, in-contrast to pristine SnO2-based PSCs (20.23%). Moreover, the Cs-modified SnO2-based PSCs exhibit remarkable environmental stability in a relatively higher relative humidity environment (>65%) and without encapsulation. Therefore, this work suggests that Cs-doped SnO2 is a highly favorable electron extraction material for preparing highly efficient and air-stable planar PSCs.

RESUMEN

InGaN nanorods possessing larger and wavelength selective absorption by regulating In component based visible light photodetectors (PDs) as one of the key components in the field of visible light communication have received widespread attention. Currently, the weak photoelectric conversion efficiency and slow photoresponse speed of InGaN nanorod (NR) based PDs due to high surface states of InGaN NRs impede the actualization of high-responsivity and high-speed blue light PDs. Here, we have demonstrated high-performance InGaN NR/PEDOT:PSS@Ag nanowire (NW) heterojunction blue light photodetectors utilizing surface passivation and a localized surface plasmon resonance effect. The dark current is significantly reduced by passivating the InGaN NR surface states using PEDOT:PSS. The photoelectric conversion efficiency is significantly increased by increasing light absorption due to the electromagnetic field oscillation of Ag NWs. The responsivity, external quantum efficiency, detectivity, and fall/off time of the InGaN NR/PEDOT:PSS@Ag NW PDs are up to 2.9 A/W, 856%, 6.64 × 1010 Jones, and 439/725 µs, respectively, under 1 V bias and 420 nm illumination. The proposed device design presents a novel approach toward the development of low-cost, high-responsivity, high-speed blue light photodetectors for applications involving visible light communication.

RESUMEN

Quantum dots (QDs) with metal fluoride surface ligands were prepared via reaction with anhydrous oleylammonium fluoride. Carboxylate terminated II-VI QDs underwent carboxylate for fluoride exchange, while InP QDs underwent photochemical acidolysis yielding oleylamine, PH3, and InF3. The final photoluminescence quantum yield (PLQY) reached 83% for InP and near unity for core-shell QDs. Core-only CdS QDs showed dramatic improvements in PLQY, but only after exposure to air. Following etching, the InP QDs were bound by oleylamine ligands that were characterized by the frequency and breadth of the corresponding ν(N-H) bands in the infrared absorption spectrum. The fluoride content (1.6-9.2 nm-2) was measured by titration with chlorotrimethylsilane and compared with the oleylamine content (2.3-5.1 nm-2) supporting the formation of densely covered surfaces. The influence of metal fluoride adsorption on the air stability of QDs is discussed.